Search Documents

By R P. Langford, T A. Moore

Over the last 15 years Indonesia has experienced a surge in coalexploration, which has led to the development of a major export industry. This coal exploration has improved the understanding of the geology of the Indonesian coal deposits. The main economic coal deposits are of Eocene and Miocene to Pliocene age, which mainly occur in Kalimantan and Sumatra and were formed from peat deposits in an equatorial paleoclimate similar to that prevailing today. Some of these peats were domed peats, which grew above the normal water tables, under a climate of year-round rainfall; these peats grew above the level at which waterborne mineral matter can enter the system, resulting in low ash and sulphur, and locally very thick coal. It is believed that such peats have formed the unusually thick, low ash, and low sulphur Miocene coals of Indonesia. Coal deposits of Eocene age are typically characterised by thinner seams, with relatively higher contents of ash and sulphur. The Miocene coals and Eocene coals both appear to have formed in lacustrine, coastal plain or deltaic depositional environments, similar to the modern peat-forming environments of eastern Sumatra and parts of Kalimantan. The Eocene coals formed mainly in extensional tectonic settings. Miocene - Pliocene coal deposits formed in a range of tectonic settings.

Jan 1, 1999

By P Gardner

The Kanowna Belle gold mine in Western Australia has reached a depth of 1000 m on the way to 1300 m. A feasibility study undertaken in 2006 identified the mining of E-Block as both technically and commercially feasible. One of the major risks identified in the study was the ventilation capacity, as the existing primary ventilation system would not support the production schedule for mining and a major system upgrade would be required. Failure to provide the necessary airflow would put the project at risk. A review of the airflow requirements and infrastructure options detailed in the feasibility study was undertaken to ensure that the assumptions and design were optimised. This review recommended a minimum airflow of 206 m3/s, but by acknowledging the necessary constraints imposed by mining at depth and re-engineering the mine layout to optimise the primary ventilation circuit, this requirement was reduced to 160 m3/s. This represents a 22 per cent reduction in airflow and a reduction in capital cost that will see mining at depth become economically feasible at Kanowna Belle. This paper discusses the processes that led to a redesign of the mining layout and highlights the importance of including the ventilation network in the optimisation process.

Jan 1, 2008

Natural leaching of minerals has been recorded for some two millenia but surprisingly only in recent years has enough been known of the process for any serious design to be made. Copper has been recovered from natural mine waters since about the 17th century but again little progress was made in de- sign procedures until recently. Natural or dump leaching was started as a recovery process late in the 19th century and in the years up to the classic study of Taylor and Whelan in 1943 a series of impirical optimis- ations made it a valuable process for treating low grade or waste material. The biological nature of Sulphide leaching was proven by Colmer and Hinkle in 1947 and since then a large mass of data has accumulated on the microbiology, biochemistry, and response of ores to this form of attack. In spite of this knowledge and the vast amount of pract- ical experience available there are few recorded attempts to present methods of calculation or design procedures that can be used for setting up a leaching process. A framework is given here on which such procedures can be based and indications given of the inherent advantages and limitations of the process,

Jan 1, 1969

The process of refurbishment is not a precisely defined one. It is under- stood to mean an upgrading of a plant which is normally performed only once. The application of refurbishment in the field of materials hand- ling equipment poses particular problems because complex plants con- sist of individual components having quite different remaining service lives. For this reason, a systematic, proven procedure is proposed for the refurbishment of large materials handling equipment, designed to ensure economic implementation in accordance with the company goals. Rheinbraun2 has been using materials handling equipment since 1900, the largest units today being bucket-wheel excavators with a daily capacity of 240,000 bank cubic metres of overburden and a service weight of up to 13,500 t (metric tons). Since 1975, more than 50 large-scale refurbish- ment projects have been carried out in the company. In the process, refur- bishment has turned out to be the proven alternative to replacement of large materials handling equipment. Rheinbraun Engineering,3 a Rhein- braun subsidiary, carries out planning, consulting, and supervising work in the implementation of refurbishment projects in Germany and abroad. The most recent example is the refurbishment of Dredger 11 of the State Electricity Commission of Victoria in cooperation with Krupp-Australia, Melbourne.

Jan 1, 1989

By Steinbrucker G

Improvements in mining by the application of electronics necessitates analy-sis of the objectives and problems. A detailed analysis has shown that increased tunel-ling performance is one of the most important objectives. In mining, the environmental conditions for machines, their handling and servicing are very hard. Therefore a health monitoring system for tunnelling machines in hazardous areas has been developed. This system measures operational parameters, such as-flow, pressure, temperature, etc., de-rives forecasts of possible failures from these values, and assists maintenance person-nel. Important data are transmitted to a surface computer via telephone cables. Health monitoring is based on the cognition that slow deterioration of characteristic parame-ters, e.g. fluid loss, are symptoms of wear. Sudden changes of machine parameters indi-cate sudden destruction. Computer technology is very advanced, but transducer technolo-gy has not,been able to keep pace. Filling the yawning gap in the mining industry is a challenge to technology and requires special techniques. Machine monitoring and automa-tion in underground mining is still in its infancy. A lqt of development and research work is still necessary. The risks are great-The expected benefit due to increased min-ing performance (up to 5 %) justifies the risks in development.

Jan 1, 1985

By Rienks, Wyborn D

The Ravenswood Batholith in the Charters Towers -Ravenswood area of north Queensland, was formed by three main episodes of granitoid emplacement between the Early Ordovician and the Early Permian. Granite to granodiorite plutons of the first phase of intrusions in the Early to Middle Ordovician, probably formed by partial melting of a thin continental crust as a result of the emplacement of mafic material derived from the mantle. Some of this mafic material subsequently intruded the Ordovician granitoids as gabbro to diorite complexes. The early granitoids were deformed and metamorphosed prior to emplacement of second phase granodiorite to tonalite plutons in the Late Silurian to Early Devonian. These later plutons have generally not been deformed or recrystallised. Geochemical and isotopic data suggest the Siluro-Devonian plutonism may have been generated by a partial melting of the tholeiitic material emplaced in the lower crust during the Ordovician. A third intrusive phase consists principally off Late Carboniferous to Early Permian gabbro-granite complexes, high level granite to granodiorite complexes, and rhyolitic plugs and diatremes near the batholith margin. Gold mineralisation in the batholith is associated with two major events: mesothermal vein formation in the Early Devonian and porphyry types in the Late Carboniferous to Early Permian.

Jan 1, 1990

Drill and blast excavation in underground mining and. civil engineering projects has grad- ually given ground to mechanical boring of tun- nels, shafts and raises during the past twenty years. The use of.boring equipment must today be considered significant and wide spread al- though comprising only a very small percent of total underground excavation. The encroachment of mechanical boring into the domain of blast- ing has been by slow incremental advances. There have been few, if any major breakthroughs in this development, and none can be foreseen in the next decade. After 1990 it is possible that scientific. development will provide some form of breakthrough in rock breaking, but this is so uncertain that it should have little relevance to planners in the 1980's. A more near term view of the future, con- centrating on the next five to ten years, has lead to the conclusion that significant im- provements will be seen in tunnel borers for poor ground conditions. A universal machine will be developed that converts from a dry hard rock machine to a closed slurry type machine for passing through fault zones with unstable crushed rock and water. Two other machines have been described as alternate designs for tunnelling in squeez- ing ground conditions.

Jan 1, 1981

The development of the Australasian Code for Reporting of Identified Mineral Resources and Ore Reserves is a significan step towards informing the financial community and the public about the future profitability and risks of investing in resource companies. The Code is also important from the accountants' point of view because it provides them with a well-defined bash for assigning costs or attributing value to the assets of resource companies and hence improving their financial reports. Although reporting to the public is ultimately the responsibility of management, accountants, like geologists, are frequently required to provide information for inclusion in these reports. Jr the last ten years, there has been a considerable refinement in the reporting of mineral resources which can be attributed mainly tc the progress made towards developing the Code. It seems tha the classification and terminology that the geologists have developed are widely used in the annual reports. However, little progress has been made by accountants in improving the financia information. The purpose of this paper is twofold: (a) to outline briefl) some of the major problems in accounting and reporting fo; mining companies and; (b) to examine the potential contribution of the Code in solving those problems.

Jan 1, 1990

By Patridge A. C

Hydrocyclones have widespread use as classifiers in applications such as mine fill preparation and coal preparation. A fundamental conflict often exists between recovery of all of the valuable material and maintaining the quality of the product. This conflict is a result of a portion of the feed material passing through the cyclone, effectively without undergoing any classification. This paper describes an investigation, undertaken as an undergraduate project in mining engineering at the University of NSW (Brook, 1994), into aspects of cyclones in which supplementary water injection is used in an attempt to reduce the amount of misplaced fine material reporting to the coarse product and hence improve the overall classification efficiency. In particular, the study concentrated on the effects of different modes of water injection. Two methods of introducing wash water into the cyclone body were investigated. A series of tests were performed on a laboratory hydrocyclone having provision for radial water injection at different levels through small orifices in the wall of the conical section, and a preliminary study was made of the performance of a novel cyclone in which the conical section had walls of a permeable polyethylene, permitting a uniform introduction of wash water over the entire surface.

Jan 1, 1995

By Tomlinson E, Lama RD

Drainage of gas has been practiced overseas for almost half a century. Peal advances in drainage of gas to combat high emissions became practicable in the late fifties and early sixties when the technology was standardised to use it under a variety of mining and geological conditions. Today methane drainage is practiced in the United Kingdom, Germany, France, Belgium, Poland, Czechoslovakia, Hungary, Ibmania, U.S.S.R., China, Japan, Canada, U.S.A. and Mexico. Australia entered the list of countries using gas drainage on 3rd March, 1980 when the first full scale gas drainage system was set up and commissioned at West Cliff Colliery to drain gas from the Bulli Seam. Methods used in Europe are different from those used in North America, Japan and Australia mainly because of the different mining methods and also because of the limited number of seams under extraction, relatively new coal fields, and comparatively larger distance between the seams. In spite of the difference in the technique, the basic aim is the same and that is to improve ventilation and reduce ventilation costs, alleviate dangerous gas accummulation, overcome outburst hazards and ultimately make mining safer and more efficient. Over the last decade, there has

Jan 1, 1982

By Kendall W. T C

This paper provides a brief overview of the history of the Chaffers Dewatering Project which was successfully commissioned in August 1993. Until the end of 1992 the `Superpit' and the deep mines of the Golden Mile had all been dewatered by a staged pumping system from the 28 level in the Lake View Shaft, which was removed at that time when the Lake View Mine was absorbed into the Superpit. Feasibility analysis had indicated that adaptation of oil industry technology offered the greatest potential for a low cost solution to the problem of dewatering the open pit and deep mines. A KCGM engineer and one of the authors visited the Jackson oilfields to look at the deep well pumping technology in use there in early-1991. In the final analysis a new dewatering station was established in the 23 level crushing station of the Chaffers Shaft using conventional plunger pumps, but the rising main was screwed 178 mm OD (7 inch) casing the suspended from the surface to a depth of 686 metres, and was installed using oilfield personnel and methods. Only the second installation of its kind in Australia, the project achieved the dewatering objective at about half of the capital cost of the more conventional approach and at lower operating costs as well.

Jan 1, 1995

Through the stress synthesis of many exanples of macrostructure from eastern to western parts of China, it can be concluded that in Chinese tectonics there are two push- twisting forces, one of which ("Rl", from SE to NW) came from the Pacific Ocean plate thrusting over the Chinese continent plate in the eastern part of China; the other ("R2", from SW to NE) resulted from the thrusting of the India plate. The meeting line could be situated along the belt from 104¦-106¦E longitude in the middle part of China. To the south of Qinling the meeting line was an abyssal and giant fault situated from Longmen to the Er Inland Sea where the Tibet-Gansi fold system was intersqueezed to the Sidluan platform; to the north of Qinling, situated on the Fengxiang subsidence of the Eerduosi basin, the meeting line was located about 105¦E in Mongolia and appeared in the form of an arcuate structure, i.e. the Mongolia arcuate structure, which could extend to Beijiaer Lake towards the north. A new special type of structure named rotation-apart structure occurred from Gansu, Qinghai province to Ningxia, Neimeng autonomous region, in the west of Shandong province and in the western part of Chaidamu Basin.

Jan 1, 1987

A synthetic gold-silver telluride material (mainly sylvanite) has been prepared and its physical and chemical properties checked. Flotation tests using a Hallimond tube were conducted using commercial xanthate collectors. At collector concentrations of 10-3M with the addition of 5 × 10-4 M CUS04, no obvious differences in the mineral recoveries were seen irrespective of whether amyl, secbutyl, isobutyl or isopropyl xanthates were used. However, when the concentration of xanthate was reduced to 10-4 M or in the absence of the copper sulphate activator, the effectiveness of the collectors was in the order: amyl > secbutyl > isobutyl > isopropyl > ethyl. Changes in the slurry pH appeared to have little effect on the recovery of the telluride mineral.Leaching tests of the precious metal telluride showed that both gold and silver dissolve in alkaline oxygenated cyanide solutions but at a much lower dissolution rate than metallic gold or silver. Both leaching tests and electrochemical measurements indicate that the dissolution rate of gold-silver telluride is controlled by the pH and cyanide concentration of the leachant.Roasting the gold-silver telluride materials in air at temperatures between 550 and 750°C resulted in its decomposition into a metallic gold-silver alloy and tellurium dioxide.

Jan 1, 1994

Copper was first produced in Australia in 1844, at the Kapunda Mine in South Australia, and, by 18i>0, production exceeded 2,000 tons of copper a year. Output increased ,steadily, reaching a peak of 14,00Qo tons a year in 1867 and 1868, when the Burra Burra and Kapunda Mines in South Australia and the Peak Downs Moine at Clermont, Queensland, were at the height of their production. At this period, Australian copper formed a considerable percentage of the world's supply, its output equalling, for a short time, that of the United States. Production declined to between 3,000 and 4,000 tons a year after the closing of' these three mines between 18717 and 1879, and, at this stage, the Australian output came chiefly from the Wallatoo and Moonta mines in South Australia. About 19000, it began to rise again, with the extension of the railway to the copper fields of Chillagoe and Cloncurry, and, between 1905 and 1912, was at its greatest, with a maximum of 47,774 tons of copper in 1912. During this period, Australia contributed 4,7 per cent. of the world's annual production, and ranked among the six major copper-producing countries of the world (Table 1).

Jan 1, 1943

Gold-rich porphyry copper deposits areimportant sources of gold in the circum-Pacific region: 26 major deposits contain >7000 tonnes of gold. The deposits occur in a variety of subduction-related settings, and may be underlain by crust that is undergoing either extension or compression and that is either oceanic or cratonic in character. The deposits are associated intimately with composite porphyry stocks, which commonly were emplaced into coeval andesitic volcanic piles. The stocks range in composition from low-K calc-alkaline through high-K calc-alkaline to potassic alkaline. Much of the copper and gold were introduced as components of K-silicate alteration, which may undergo partial overprinting by intermediate argillic assemblages. Advanced argillic alteration is widespread in the shallow parts of the systems whereas sericitic alteration at deeper levels tends to be restricted. Gold distribution generally follows that of copper, which is present mainly as chalcopyrite with or without bornite. The gold is in the native state and occluded by cr in close proximity to the copper-iron and/or iron sulphides. The magmas and metals necessary for the generation of gold-rich porphyry deposits were derived mainly from subcrustal sources, with the subducted slab believed to play a pivotal role.

Jan 1, 1990

Thank you chairman, good afternoon ladies and gentlemen. In my talk this afternoon I intend to cover a brief history, some of the recent experiences and an overview of the McArthur River project.If we consider the themes of this forum, Obstacles and Opportunities, I can confidently say that in attempting to develop the McArthur River deposit Mount Isa Mines Limited (MIM) must have encountered almost every obstacle that can be imagined. However the large size and the high grade of the deposit has ensured an opportunity, from which it is very difficult to walk away from.The McArthur River Here's Your Chance (HYC) Deposit is located in the Northern Territory of Australia. It was discovered by Mount Isa Mines Limited geologists in 1955 and is one of the largest known sedimentary stratiform zinc-lead-silver deposits. The deposit has been the subject of numerous investigations and considerable expenditure culminating in a major feasibility study in 1979. There were a number of factors which prevented development, these being the size of the project, the fine grained mineralization, geographical location, market, social and capital cost. The latter had been estimated in the 1979 study to be $800 million at that time.

Jan 1, 1993

Rockbursts, as they occur in South African deep level gold mines, have a lot in common with natural earthquakes. Both violently release seismic energy and cause damage to underground and surface structures. Rockbursts are the main cause of fatalities in deep gold mines and the problem may increase in severity with future mining at greater depths. Although the emphasis in Rock mechanics is on the prevention of rockbursts, prediction would provide a partial solution to the rockburst problem. A research project was initiated in 1981 on Western Deep Levels to investigate the possibility of detecting and identifying precursive microseismic activity. This project has succeeded in locating potential sources of seismic events with reasonable confidence. The timing of these events may be estimated with less confidence, and an important parameter, namely the potential size of the rockburst, still cannot be determined. An example of a large seismic event and its associated precursive activity are discussed. Practical prediction systems will, at least for some time, involve subjective decision making which will place a new responsibility on the mine manager as well as the rockburst specialist. The moral pressure on the manager as the final decision maker will probably be greater than the fear of leqal prosecution.

Jan 1, 1986

By Nguyen G. H, Graham J

A laboratory-scale fluidised-bed roaster has been used to examine the effect of temperature and duration of roast on the morphology of the calcine produced from a pyritic gold-bearing concentrate. Two mechanisms of oxidation, which depend on the roasting temperature, have been identified. For samples roasted below 550°C, direct oxidation of the sulphide occurred to form hematite with a porous fine-grained concentrically-layered texture. The surface area of the calcine increased with an increase in roasting temperature in the range 400 to 500°C. For samples roasted above 550°C, the first reaction was the evolution of sulphur vapour to produce pyrrhotite, which underwent increasing grain growth as the roasting temperature was increased. This had the effect of decreasing the surface area of the calcine. The pyrrhotite was subsequently oxidised to produce hematite.Leaching studies using cyanide solution indicated that gold extraction around 95 per cent was achieved at temperatures of 500°C and above, with optimum extraction, taking into account rate and cyanide consumption in the range 550 - 700°C. Hence recovery did not decrease with decrease in surface area of the calcine. Observed gold in leached calcines was mainly enclosed in thin oxide walls of the hematite, with minor quantities enclosed in quartz and silicate minerals.

Jan 1, 1995

According to the data provided by the most recent European Survey on Working Conditions, roughly 25 per cent of the European working population is exposed to mechanical vibrations for no less than one quarter of the work shift duration, while around ten per cent are exposed for the entire work shift. The occupational exposure to whole-body vibration (WBV), in particular, represents a major health risk in mining, quarrying and civil excavation activities. In accordance with European Directive 2002/44/EC, the latest version of the Italian law on physical risks has recently confirmed the possibility of using relevant literature data on vibration magnitude in order to evaluate personal occupational exposure (vibration database or data provided by the manufacturer). Still the alternative option, based on field measurements, represents the most appropriated method of risk assessment, as it accounts for the actual operating condition at the workplace; actual operator and vehicle under investigation and specific working cycle. The article discusses the vibration measurements taken on a number of heavy machinery (excavators, loaders, trucks, dumpers, etc) employed for talc extraction in a mine located in Sardinia and the resulting personal exposure for the drivers. The assessment was carried out in accordance with the specifications of ISO 2631-1 and EN 14253.

Dec 6, 2010

The optimisation of a mining operation requires precise ore grade control, metallurgical accounting, and laboratory sampling protocols, which are implemented by using accurate and flawless sampling systems. Good sampling practices, and sampling technologies in these fields have been historically poor and too many existing sampling systems available on the market are flawed in many ways. This is mainly the result of a poor understanding of the Sampling Theory, and the natural result of international standards on sampling that fail to present the Sampling Theory in a logical way, that still promote non-probabilistic sampling, and that fail to address the important details that make a correct sampling system. Many standards barely mention the Sampling Theory in appendices when it should be clearly the main body of a reliable standard on sampling. As a result, many standards show only little expertise in the Sampling Theory. Conventional statistics should only be a scientific tool for the Sampling Theory to reach its height, which has always been well understood by its creators. Conventional statistics can indeed be addressed in appendices of standards in sampling, but not the other way around. Until the Sampling Theory is recognised as the main body of a standard on sampling, incorrect sampling technologies will plague the market, and make it impossible for mining operations to optimise their mining and metallurgical processes. This paper makes a short list of correct new sampling technologies that have been created with respect to the principles taught in the Sampling Theory. Also, suggestions are presented to create better international standards on sampling, which would provide a stronger incentive for manufacturers to build correct sampling systems, and for engineering firms to install only sampling systems that respect the rules of sampling correctness listed in the Sampling Theory.

Jan 1, 2004