Search Documents

A small-charge rock excavation method based upon the Penetrating Cone Fracture (PCF) technique has been demonstrated to be capable of excavating the hardest of rocks. The PCF technique involves drilling shallow holes in the rock which are then pressurised at the bottom by a propellant charge device. A controlled fracture is initiated at the hole bottom comer and propagates in such a manner as to excavate the rock at an energy efficiency three to five times better than explosives. Due to the low flyrock velocities and airblast pressures realised with PCF breakage, the method may be used in close proximity to equipment and personnel and is thus ideally suited for integration into continuous hard rock excavation systems. Over the past 18 months full-scale testing of the PCF method has been carried out in mines in the US and Australia. This testing has utilised a 76 mm diameter gas injector for hole pressurisation and employed propellant charges ranging from 80 to 320 gm. In addition to extensive data on rock excavation performance, data on ground motion, dust, carbon monoxide and air blast have been obtained. These data indicate that none of the parameters associated with PCF breakage are detrimental to the development of PCF-based, continuous-excavation machines. Machines employing the PCF method may range from simple single-boom machines for secondary breakage and small precision-blasting jobs to integrated systems with several booms, continuous mucking capabilities and ground-support equipment for drifting and tunnelling.

Jan 1, 1993

By Scales PJ

Fatigue is the primary cause of failure of structural and mechanical components subject to dynamic loading. Recognition of this basic fact and the development of appropriate techniques and details are important in the design and repair of off highway trucks (OHTs). The frames and appendages of OHTs and other mobile plant used in the Pilbara are subject to tough operating conditions. Any fatigue-prone details quickly show up and become a maintenance liability of considerable concern. Much of this equipment is approaching the limit of its fatigue life and maintenance managers face decisions on whether to repair or replace. Even new equipment often contains some poor details which suffer distress soon after commissioning. In those cases a repair is required which will reinstate the detail to its original intended design life. Repair details must be practical and cost effective. They must also be tailored to the capability and expertise available in the field or in local manufacturers' establishments. This is particularly important where original equipment was manufactured overseas and long delivery times are involved. Lessons are drawn from components which have failed, using the evidence constructively, to provide an upgraded part or an improved substitute. With the experience now available it is relatively easy to extrapolate to cover new problem areas. This paper describes specialised techniques of mechanical fastening and detailing for low fatigue susceptibility, built up over many years of experience with OHTs and other mining plant and equipment in the Pilbara.

Jan 1, 1982

By Campbell Brown G F

THE Mount Morgan mine has, from the time of its historical discovery, been the subject of investigation and speculation by geologists and mining engineers. The first examination was made by Dr. R. L. Jack, in 1884. He came to the conclusion, from theevidence then available, that nothing but a thermal spring in the open air-otherwise a geyser-could account for the formation of the ore body. This report attracted world-wide attention at the time. Since then the mine has been examined by most of the leading geologists of Australia, and by many from elsewhere. In all cases the examination has only extended over a period' of a few days or weeks, and in the light of present knowledge of the deposit we know that sufficient data could not be obtained in such a short time to warrant the statement of definite conclusions. It is not to be wondered at, therefore, that a considerable difference of opinion exists as to the genesis of the deposit. That the company considered more detailed investigation necessary is shown by the fact that some thirteen years ago it employed Mr. Charles Walker as geological surveyor on the .mine. At that time also the data available was insufficient to give satisfactory results. It is, however, a matter for comment that none of the geological reports on the property took notice of the increase of copper values in the ore with depth, though the present workings and diamond-drilling...

Jan 1, 1911

ATTENTION has recently been directed to the subject of dust production and methods of allaying same in the Broken Hill mines, so that the time would seem opportune for the local branch of the Institute to discuss certain features of an important phase of the health question in connection with underground work. Tests conducted in the Broken Hill South mine and at other mines at Broken Hill have shown that the ordinary operatioils of mining, such as boring, blasting, and shovelling, may be accompanied by the production of considerable dust unless water is judiciously used.In South Africa·dust particles under 5 microns size are regarded as dangerous, becailse they are so small as to be invisible to the naked eye, and wm esc'ape the protections set up by nature in the nose and throat, and thus may be inhaled in large quantity. A micron is 1 25000th part of an inch. This paper contains an account of the work done on the Broken Hill South mine chiefly, though some tests were done on other local mines.An acknowledgment is due to Mr. T. A. Reid, of the Broken Hill South mine, who conducted some of the tests herein mentioned, and under whose supervision most dust counts were made. Numerous dust samples have been taken by means of thekonimeter, an instrument designed by Dr. Kotze, the Government mining engineer of the Union of South Africa, and fully described...

Jan 1, 1921

By E Ferrow, R Herbert, M E. Malmstr, M Fuchs

The study of microbial sulfide oxidation and oxidation rates of tailings requires the use of sterile control samples in laboratory experiments for comparison purposes. The need for sterile tailings sand is also apparent in the study of microbial communities and processes. This study compares six different methods with regard to sterilisation efficiency and investigates chemical and mineralogical changes in the samples as the result of sample treatment. In addition, the effect of sterilisation on mineral weathering rates is also studied. The efficiency of the different methods with regard to sterility is estimated by most probable numbers (MPN) of both sulfur and iron oxidising bacteria. The sterilisation methods that were compared are: washing with sterile water, washing with ethanol, applying antibiotics, repeated heating to 70¦C, autoclaving, and γ-irradiation. There are several possible drawbacks with the different methods, including the risk of an applied chemical acting as a substrate for micro-organisms in the system, and the risk of altering the tailings. The results show a substantial difference in sterilisation efficiency between the treatments. For example, autoclaving, repeated heating, ethanol and irradiation efficiently kill micro-organisms, rendering an undetectable amount of bacteria after one month of incubation, whilst washing with water exhibits virtually no microbiological effect, with a bacterial content comparable to the control. The use of antibiotics for sterilisation ranks intermediate: the lag-phase was twice as long in the antibiotics treatment compared with the controls. X-ray diffraction, optical and electron microscopy, M÷ssbauer spectroscopy, and mineral magnetism indicate no significant change in the bulk mineralogical composition. However, X-ray photoelectron spectroscopy analyses show that with some of the treatments, sulfides are partially oxidised, as indicated by the formation of sulfate and partially û oxidised sulfur species at the tailings surfaces. Aerated batch weathering experiments performed on sterilised tailings samples and untreated controls indicated that while the initial rates of element (S, Fe, Cu, Zn, Mg, Na, K, Ca) release may differ between the samples, over the course of ~100 days of experiment at pH 2 and room temperature, the rates declined toward a similar value for all samples. To conclude, there does not appear to be one perfect method for tailings sterilisation. Autoclaving and heating damage the mineral grain structure and oxidise the sulfide surfaces. Ethanol, antibiotics and rinsing greatly alter the pore water chemistry through the washing procedure. In addition, ethanol and denatured antibiotics might serve as a substrate and also, in the case of antibiotics, adhere to mineral surfaces thus obstructing chemical reactions. Irradiation seems to be the preferable method on an overall basis, although the formation of surface Fe3+ was suggested by M÷ssbauer spectroscopy.

Jan 1, 2003

By K Gilliland

The past decade has seen the widespread implementation of computerised real-time operational management systems in open pit mines. While these systems have made a significant impact on operational efficiency at a process level, surprisingly little work has gone into integrating these systems with other IT systems, including those used for tactical planning and enterprise resource planning. As a result of this gap in the information hierarchy, the goal of optimising an entire operation, or multiple operations, remains elusive. Implementation of computerised operational management systems in underground mines has been much slower. This is a significant, though often overlooked, reason why the productivity for underground mining is generally so much lower than for open pits. The historical reluctance to implement computerised operational management systems underground can in part be attributed to the underground environment, particularly the difficulty in establishing effective communications. Another factor retarding the implementation of systems underground has been the perception that the nature and scale of underground mining does not lend itself to computerised operational management. This perception can be challenged, not only by a process level examination of the underground mining, but also by a holistic examination of the entire industry. In recent years, the mining industry as a whole has destroyed rather than created wealth and underground mines are major culprits. The degree of value destruct has been more pronounced with underground mines, as the usual problem û low commodity prices û has been exacerbated by the harsh environment, low productivity and a æfog of warÆ no longer generally found in open pits. Faced with these realities, underground mines will have to adopt modern management tools or suffer extinction at the hands of an unsympathetic investment community. All is not gloom and doom, however. Technological advances have largely overcome the difficulties associated with the underground environment. As a result, there is a small, but growing, number of underground mines using computerised operational management systems to directly improve the bottom line. Much greater improvements can be realised if the industry takes advantage of the recent convergence in technology, to integrate process information with tactical and enterprise resource planning systems in order to provide a solid platform for all decision-making. This would result in the æeÆ mine. Given that the underground fraternity is essentially starting with a blank sheet, they have the opportunity to æsteal a marchÆ on open pit mines, who may be constrained by legacy systems. The benefits of the æeÆ mine are presented through a hypothetical case study that examines the shortfalls of the non-æeÆ mine. The paper ends by presenting a future vision for the æeÆ mine.

Jan 1, 2000

The object of this talk is to bring before members the importance of the prospector and the' State Battery system to the wealth and prosperity of the mining industry in particular and the State of Western Australia in general, and to touch on the more important features.Customs plants of any sort are usually subject to a good deal of critioism, usually on the large profits made at the expense of the customer, etc., and this often clouds the real value of the work being done.Prospectors, on the whole, are a good class of men; they work under conditions and difficulties which would deter those less spirited. Food, water and mining supplies are often difficult to obtain and frequently have to be transported great distances. Their mining tools are usually of the most primitive type, yet during last year over 109,000 tons of prospectors' ore were handled by the State Battery system for 73,250 fine oz. valued in Australian currency at over £587,000, the value being 57/- per long ton at par.This production brings the State Battery system into fourth position amongst the producers of the State, the yield being exceeded by the Lake View and Star, Wiluna and the Great Boulder.In passing I might mention that these notes were written at the end of the year 1940, and the above figures were for the previous period. The figures for last year, 1940, were not quite so good, being 101,000 tons for approximately 60,000 fine oz., valued in Australian currency at £572,000.In spite of this drop the State Battery system maintained its position as fourth in order of gold output for the State.The extractions, as a whole, throughout the system, were 92·54%, made up of 68·86% by amalgamation and 23·68% by cyanidation. These figures, for a group of 20 plants treating widely different classes of ore, must be considered satisfactory. The total production since inception is over £11,000,000 in Australian currency.State Batteries are usually more or less of a standard design. Ore is reduced to about 2i in. maximum size before being sent to the bins. Challenge automatic feeeders control the feed to each mill unit, amalgamated copper plates collect the free gold. Corduroy strakes are used with some ores after amalgamation, but in only a few cases has this been found of any advantage to the customer.The pulp from the battery is sampled, after leaving the tables, with a "Tazewell" sampler and pumped to dams for subsequent cyanide treatment.The "Tazewell" sampler is a machine driven by the moving pulp; and takes about fifteen dips per .minute from such pulp through a slotted...

Jan 1, 1941

By M Skead, H Michael, R Chase, A Davidson

Ashanti Goldfields CompanyÆs (AshantiÆs) most recent development is the Geita Project in the Lake Victoria Goldfield of NW Tanzania. It comprises six distinct gold deposits within two mineralised trends: Nyankanga, Lone Cone, Geita Hill (Geita trend) and Matandani, Kukuluma and Area 3 West (Kukuluma trend). Between 1936 and 1966, the Geita area produced an estimated 5.5 M tonnes of ore from five underground deposits at an average recovered grade of 5.3 g/t. The discovery of Nyankanga was made by Ashanti in 1996 from RAB drilling of a +100 ppb Au anomaly in laterite soil above ferricrete cover. The Kukuluma trend was discovered by SAMAX Resources (taken over by Ashanti in 1998) between 1996 and 1997 from RC drilling of a +80 ppb Au laterite soil anomaly. Oxide facies banded iron formation (BIF) of the Upper Nyanzian System forms prominent topographic ridges and is the dominant host lithology for gold mineralisation. The ridges are flanked by felsic tuff units which lie stratigraphically above. Syn-genetic lamprophyre (vogesite) and post-genetic felsic dykes are also seen in the Geita trend. At Nyankanga a granodiorite-diorite suite has intruded as dykes and sills into BIF from a plug centred on a WNW fault and has produced wallrock alteration assemblages similar to those seen in Cu-porphyry systems (potassic, propylitic, etc) as well as sulphide and gold deposition. However, the main ore-grade mineralisation (as in the rest of the Geita trend) is controlled by low-to-medium angle structures dipping north-west and north with numerous splays in the hanging wall. High-grade shoots at Nyankanga plunge to the west and to the north-west, being lithologically and fault-controlled respectively. At Geita Hill the higher grade shoots are controlled by fold noses in BIF dipping to the north. Free gold occurs within fractures of sulphides. The deposits of Kukuluma and Matandani occur on an ancient (possibly Cretaceous) erosional plateau and are related to two WNW to NW trending shear zones, discordant to the local strike of the BIF sequence. Complete oxidation occurs up to 120 m depth and there is a strong supergene component to the gold distribution. Primary gold mineralisation is divisible into two distinct assemblages: arsenopyriteûpyrrhotiteûmagnetiteûchlorite associated with brecciated cherts and pyrite associated with shaley banded ironstones. Area 3W is most likely the fault-displaced extension of the same mineralised trend and comprises thin, intermittent zones of high-grade gold mineralisation occurring adjacent to a ridge in banded cherts and minor BIF. Current resources (measured, indicated and inferred) for the project are estimated at 89.24 Mt at an average grade of 4.17 g/t (11.97 Moz of contained gold) at a 1.0 g/t cut-off grade. Of this 9.83 Moz is within the Geita trend and 2.14 Moz is within the Kukuluma trend. A resource of 2.74 Moz is from an inferred resource at depth at Nyankanga where the viability of an underground operation is being studied. Proven and probable reserves are 49.77 Mt @ 3.46 g/t (5.54 Moz) based on a $325/oz gold price providing a mine life of ten years at an average production rate of 500 000 oz per year. Reserve estimation was carried out using mineable polygons to select resource blocks based on a series of mining and costs parameters. In addition key cost parameters were tested to provide sensitivities for pit optimisations and pathfinders for negotiations with suppliers and contractors. Construction began in March 1999 and first gold is expected to be poured in the second-quarter 2000.

Jan 1, 2000

By T Atchison

The Vale Ferro Carajßs S11D project in northern Brazil is based on the movement of unprecedented volumes of waste and ore for mobile in-pit crushing and conveying or ætrucklessÆ systems. In peak years, the system is intended to handle a combined 160 Mt of material.The planning and implementation of the first such system for Vale, in a remote greenfield site, utilising the services of a range of international study, design and supply partners has provided a unique set of technical and project delivery challenges. The lessons from these are of value to the industry as the trend to remote and high-volume operations continues.This paper describes the key features of the mining system and documents the challenges and mitigations for important technical, cultural and project delivery issues that have arisen. It is a combined description of the journey taken by both Vale (as owner) and SKM (as delivery partner) over the course of many years.CITATION:Atchison, T, 2013. Lessons from the S11D truckless mining project, in Proceedings Iron Ore 2013 , pp 177-184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By L E. Howard

Micro-computed tomography (Micro-CT) is an X-ray imaging technique that produces high-resolution 3D computerised ‘virtual’ models of geological specimens based on the X-ray attenuation of different materials in the specimen. The ‘virtual’ specimens are made up of voxels, the 3D equivalent of pixels, each assigned a gray value based on X-ray absorption. Micro-CT has enormous potential for allowing non-destructive, digital analysis of structure and composition when the mineralogical phases can be digitally separated. However, variation in X-ray flux between scans results in highly variable grayscale values for identical materials. Consequently, materials usually have to be segmented manually, which is subjective, inaccurate, labour-intensive and time consuming. Here we present a protocol and imaging software package that can be used to accurately and precisely extract quantifiable information in a repeatable and objective fashion. The software will allow the separation, visualisation, measurement and analysis of spatial and volumetric distribution of different mineral phases without damaging the specimen. This paper explains the potential use of this protocol and software package to ultimately allow automatic segmentation and quantification of gold in drill core samples, removing subjectivity and inaccuracies from data processing.

Sep 5, 2011

By R R. Large

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The formation of orogenic gold deposits is commonly a two-stage process. The first stage involves preconcentration of gold in a suitable source rock, such as carbonaceous black shales, felsic volcaniclastics or komatiitic volcanics. The second stage involves the release of gold (commonly with arsenic and/or tellurium) from the source rocks during metamorphism or magmatic intrusive events, accompanied by the replacement of source rock pyrite by pyrrhotite. Recent research suggests that synsedimentary gold trapped in the structure of diagenetic arsenian pyrite in reduced carbonaceous facies of continental margin sedimentary basins is an ideal source of gold for many orogenic and Carlin-style gold deposits. The conversion of diagenetic arsenian pyrite to pyrrhotite during basin closure and greenschist facies metamorphism is the key process releasing gold and arsenic to the metamorphic fluid, with metal deposition in structural trap sites to form the deposits.CITATION:Large, R R, 2015. Orogenic gold deposits – a two-stage process of gold enrichment, in Proceedings PACRIM 2015 Congress, pp 335–340 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By M Zhu, G Tranell, N Simkhada, K Jakovljevic, M Wallin

Silicon is a vital element in many products today, such as electronic components, solar devices, high-quality alloys, and many others. The growing global demand highlights the need for the development of sustainable production methods to meet this demand as an alternative to the current carbothermic reduction, submerged arc furnace (SAF) based process. An alternative to this is the aluminothermic reduction of quartz in a CaO-SiO2 slag, which not only reduces direct carbon dioxide emissions but also promotes the utilisation of secondary raw materials such as quartz fines, aluminium dross and scrap as well as secondary alumina (SA) from dross recycling. In the current study, the effects of SA and CaF2 additions to slag on the resulting metal composition and metal yield were explored. Results were compared with thermodynamic simulations using FactSage™ 8.1. Experimental results show that, in agreement with thermodynamic simulations, the silicon content of the alloy is increased, while the Ca is decreased for starting slags where CaO-SiO2 is partly replaced by CaF2. Similarly, the addition of SA to the initial slag results in an alloy with a higher silicon content.

Jun 19, 2024

By S L. Nicol, B J. Hogg, O J. Mendoza, S Nikolic, A Burrows

The top submerged lance (TSL) technology, developed in the 1970s, is now widely used for the processing of a range of materials. The key advantage the ISASMELT™ TSL technology provided was the ability to process feed materials in a highly turbulent bath, reaching close to equilibrium conditions, uniquely allowing for operation below the liquidus of the molten slag phase. The details on what happened below the liquidus line in the phase diagram became critical for the successful operation of the technology. During the development of the ISASMELT™ technology this led to a collaboration between the Process Technology group of Mount Isa Mines, now part of Glencore Technology, and the Pyrometallurgy Research Centre (PYROSEARCH) at The University of Queensland. The fusion of the phase equilibria research into the technology development allowed for understanding of the behaviour of molten splash, reliable tapping of the furnace, and the ability to operate the furnace with a refractory lining and achieve a year campaign life in excess of four years. The outcome has allowed for the highly successful adaption of the ISASMELT™ technology to recycling of complex feed streams necessary to drive circularity in our modern global economy.

Aug 21, 2024

By A L. Randriamanjatosoa, G Small, C Greet

In flotation simulation models, the effects of pulp chemistry other than pH are often ignored and reduced to particles hydrophobicity or contact angle, neither of which can be measured readily in real time in an operating plant. The flotation response of a given sulphide mineral is known to be influenced and can be improved by changing the chemical characteristics of the pulp during grinding and flotation. The on-line measurement of pulp pH, potential, dissolved oxygen, temperature and oxygen demand of a process stream was completed with the PCM® (Pulp Chemistry Monitor) developed by Magotteaux in this study. The data generated together with relevant plant operating parameters were used to construct an empirical model and simulate the metallurgical performance of the ore. The same approach was also applied to laboratory flotation tests data using various grinding media types. The flotation models better fit the actual data when the chemistry of the pulp is taken into account.CITATION:Randriamanjatosoa, A L, Greet, C and Small, G, 2018. Effects of pulp chemistry on plant and laboratory flotation modelling, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 423–432 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By B Tutmez

Determination of stress-strain behaviour of rocks plays a crucial role in understanding the response of rocks during loading. However, it is a tedious, expensive and a time-consuming process to obtain such characteristics both in the laboratory and in situ. On the other hand, non-destructive testing methods such as ultrasonic velocities can produce a reliable and fast solution to indentify state of strain and stress in rocks. The present paper aims to provide insight into the relations amongst ultrasonic wave velocities, amplitudes and deformability properties of porous siltstone under compressive loading. For this purpose, pulse (vP) and shear wave velocities (vS) along with amplitudes (AP - AS), and applied loads with resultant strain were measured simultaneously so that response of siltstone to compression can be evaluated. In addition, initial vP and vS were recorded at the beginning of each test to calculate dynamic elastic properties of the specimens. This provided a comparison between static and dynamic elasticity properties of siltstone. Crack damage associated with the onset of dilation was also investigated. The results showed that there is a non-linear logarithmic relation between velocities and stress-strain level for siltstones.

Sep 26, 2011

By I T. Cameron

The commercial production of copper metal involves a sequence of purification stages. One step of this process eliminates bulk quantities of iron and sulphur from matte Cu2S(FeS to produce blister containing 95.5 per cent copper. This task is traditionally performed in the Pierce-Smith converter, a cylindrical vessel in widespread use throughout the copper industry. Typically, multiple Pierce-Smith converters are arranged along an aisle, simplifying material transfer from vessel to vessel. Materials are moved through the aisle in pots and boats, using overhead cranes. In terms of the overall process, the converter aisle represents a critical processing unitùit contributes significantly to the value added nature of the metal. The aisle is subject to significant process disturbances. Thus, improvements in the operationÆs modes and conditions have a direct impact on process profitability. As with any commercial operation, improvements are always sought to increase process performance. The general approach involves process modelling, followed by an application of control and optimisation theory to this model. The results of such a study are then applied to the real process, leading to improved performance.

Jan 1, 1998

By R G. Jeffrey

The Northparkes, Endeavour 26 orebody is a porphyry copperûgold deposit and comprises a moderately to well jointed rock mass characterised by gypsum veining, the intensity of which decreases with depth. The top 480 metres of the orebody is currently being mined by block caving, the undercut dimensions measuring 196 metres in length by 180 metres in width. Continuous caving was never achieved after the completion of the undercut thus cave inducement techniques were sought to maintain caving so as to safely sustain production. The use of hydraulic fracturing as a cave inducement tool was successfully trialled in December 1997 using existing exploration boreholes located midway up the current lift. Subsequent fracturing campaigns have enjoyed various degrees of success and have yielded in excess of seven million tonnes of ore at a significantly lower cost than conventional cave inducement techniques. Monitoring of both the hydraulic fracture system and the rock mass response has provided considerable insight into the geometry, growth and influence of hydraulic fracture networks above the Northparkes block cave, and has initiated additional research into the use of hydraulic fracturing in other mining methods.

Jan 1, 2000

By K P. Crameri

The Beta Hunt orebody is situated on the south western limb of the Kambalda dome. It is one of the nickel occurrences in the area which fall into the category of æKambalda Style OrebodiesÆ. These orebodies are renowned as being continuous uniformly mineralised ribbons of nickel sulfide mineralisation. Interestingly, Beta Hunt does not conform to this notion of continuity and uniformity and is in fact highly irregular in its ore distribution due largely to the influence of post depositional structure. In an attempt to understand the ore distribution at delineation stage rather than development stage a detailed footwall topography model is created using all available drilling data. To augment this drilling data, the routine use of downhole EM and borehole radar has been introduced to provide data beyond the confines of the drill core to enhance the geological interpretation of the footwall topography and the distribution of the mineralisation. The implementation of a detailed footwall model and the use of downhole geophysics has proved to be very effective in resolving the orebody complexity issues. Ongoing development of the methods used will continue to refine the interpretation of the geology to enable more efficient extraction of the orebody.

Jan 1, 2006

By B Dold

"Mining has still today high potential for improvement in the exploitation efficiency. Especially low-grade ores have very low recoveries. In Cu bioleaching operations from porphyry copper deposits extraction of only five and 15 per cent with maximum of 40 per cent are reached. This means that 60–95 per cent of the resource is not exploited. Consequently, any metal not extracted will end up in the waste material, therefore increasing the risk of environmental pollution. This inefficiency is mainly due to the use of element concentrations for decision-making on the daily basis of a mining operation (eg cut-off ore grade, acid-base accounting – ABA). If, instead, quantitative mineralogical and geochemical data together with information on the bioleaching behaviour of the ore assemblage (the biogeometallurgical approach), is used for decision-making right from the beginning of the exploitation, higher recoveries and less environmental impact can be achieved, ie an increase in sustainability can be reached.CITATION:Dold, D, 2016. The Biogeometallurgical Approach – the Information We Need to Increase the Sustainability of Mining, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 169–172 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By Sano S, Ishikawa T, Nagaoka H, Hayashi Y, Hasegawa M

The stirred mill is regarded as one of the most efficient devices for micronising materials and has come to be actively used for preparation of fine particles. Recently, the demand for ultrafine particles was increased in many kinds of industries. In this paper, autogenous grinding to get submicron particles based on mutual friction feed material has been carried out using a stirred mill. The mill used was made of stainless steel and its volume was about 5.5 litres, and has 12 impeller blades. Sample used was limestone. In the present work, two operating parameters such as stirring speed and feed size of limestone were considered. The ground products were sieved in the size range from feed size to 325 mesh (45 lun), and from 45 to 0.17 pm the size distributions were measured by a laser diffraction and scattering method. The progress of grinding was evaluated by the increasing amount of submicron particles in products. As a result, the rotational speed of impeller with the minimum energy consumption to produce submicron particles was observed. It was found that the autogenous grinding with a stirred mill is an effective method for producing submicronized limestone.

Jan 1, 1993