Search Documents

By Klenowski

Rational design of layouts for longwall operations is greatly facilitated by use of an accurate and economical method for predicting stresses and displacements. The displacement discontinuity method (a form of boundary element method) is based on replacing actual excavation geometries by thin slits of the same plan area. This approach allows three-dimensional stress- analysis at a fraction of the cost of alternative methods. The analyses can be readily performed on economical microcomputers, putting the analysis capability within the reach of mine-site personnel. This paper describes investigations associated with the German Creek Central Colliery, the first longwall operation in Queensland's Bowen Basin. The material properties used in the model, in particular the rock mass and goaf properties, have been 'tuned' to fit stress measurements obtained during extraction of the first and second longwall panels at the mine. The study shows that model predictions based on suitably scaled anisotropic rock strata properties are in good agreement with the stress measurements made to date. This model predicts average chain pillar loads significantly higher than predicted by models based on United Kingdom conditions. A working chain pillar design method is proposed using average pillar loads predicted by the numerical model and ultimate strength characteristics given by Bieniawski's formula.

Jan 1, 1988

By Kurihara M

In Japan, shield tunneling method is generally used to drive a tunnel in sand layers around the urban area. In this report, appli- cability of NATM (New Austrian Tunnelling Method), which uses rock bolts and shotcrete as support, to water-bearing sand layers is studied aiming at establishing more economical tunnel driving technique. After the geological exploration, the conditions (i.e. pitch of steel supports, water content, cohesion, and fine content of ground,)necessary to ensure the face stability were investigated by using centrifuge loading tests. Concerning measures to manage ground water, an air permiability test was carried out to investigate the effect of the compressed air to cut-off inflow, and pumping test to study the applicability of dewatering. Furthermore, two dimensional elastic FEM analysis consider- ing progress of the excavation face was perform- ed to analyze stresses in the support system and deformation of the ground, and to investi- gate safety of the support and the ground. From these prior investigations, possibility of the applicability of NATM to the present pro- ject was predicted. Finally, based on these results, a real scale field application test was put into practice to confirm the prediction, and to pursue construction efficiency and phenomena which could not have been predicted Beforehand.

Jan 1, 1987

By Jaracz K

At the operation of mine winders in deep shafts considerable oscillations of winding ropes may occur due to elasticity of both wind-ing and balance ropes. The amplitudes of longitudinal oscillations may reach + lm at relatively low frequencies, ranging from 0.5 to 2 c/s. These oscillations may be dangereus for the rope and produce several hazards to the winding installation as a whole. They may cause conside-rable instant accelerations on the pulley and dangerous tensions in ro-pe wires. The excessive acceleration may cause the uncontrolled rope slip on the pulley. Several methods of limitation of these accelera-tions were developed, some of them have been already in control system: of electric drive of the winder. The most simple ones are: a/ limita-tion of the rate of change of acceleration and retardation of the win-der /so called "jerk"/ and b/ the proper selection of regulators of the winder control system to get the optimal control. The trouble in solv-ing the problem of rope oscillations is that the dynamic system of the winder is a nonstationaryone owing to changing distance of conveyance from the pulley. Besides, the system is described by the equations with distributed parameters. The brief discussion of the theory and its practical aspects are enclosed as well.

Jan 1, 1985

The introduction of large diameter holes to underground mining has provided the first opportunity to apply near spherical charges in production scale blasts instead of the convent- ional long cylindrical charges generally used in stope and pillar mining. A modified version of the cratering prin- ciple was applied in the blast design in extrac- ting ore across a horizontal area of a stope or pillar. The new rock breaking technique has developed into the Vertical Crater Retreat (VCR) mining system and eliminated raise boring, slot cutting and dilution of the ore by back- fill material. Furthermore it has reduced labour and time requirements thus becoming not only a low cost method of mining but the safest method of underground mining known today. Exceptionally fine muck is provided with a minimum of damage by blasts to walls and re- treating backs of the stope or pillar. The VCR method can also be used for drop- raising, and for the excavation of underground cavities for almost any purpose . The proper explanation of the breakage mechanism of the near spherical charges opposite to the cylindrical charges yet to be found. The mining industry has quickly recognis- ed the value of the VCR mining method which is being adopted by an increasing number of mines

Jan 1, 1978

By Dobos K

The Clermont Goldfield, from which about 300,000 oz of bullion have been extracted, was one of the major gold producers in Queensland. This paper is derived from a systematic study of the mineralogy, geochemistry, and stable isotope geochemistry of the deposit, based on detailed field work and logging of 57 reverse-circulation percussion drilling holes at the Black Ridge Gold Deposit (Fig 1), aimed at addressing the long debated question of gold-ore genesis at Clermont, i.e., whether it is of fossil placer or hydrothermal origin.Detailed petrologic and mineralogical studies indicate the hydrothermal alteration at Black Ridge is dominated by extensive siderite (+rhodochrosite-ankerite) veinlets and stockworks, which are concentrated along the deformed unconformity between the Anakie Metamorphics and basal conglomerates of the early Permian Blair Athol Coal Measures. Siderite alteration is also moderately developed in all other rock units represented at Black Ridge, including the Tertiary basalt. Weak to moderate phyllosilicate alteration is common throughout the deposit, including chlorite-sericite along the shear zone of the unconformity, and sericite-clay in the conglomerates. A sulphide-oxides zonation also has occurred, including pyrite below the unconformity, (pyrite)-chalcopyrite-marcasite-(hematite) along the deformed unconformity, and marcasite (hematite, pyrite) in the conglomerates.

Jan 1, 1990

By Nidagal V

This paper discusses the dewatering strategy adopted and the considerations and procedures required to incorporate a dewaterinq scheme into the Mt Whaleback mining operation. It concludes that in pit pre-dewaterinq has successfully allowed mining to progress below the standing water level with the minimum of disruption or radical change to the mining method. It is recognised however, that dewatering is not a static activity and there is a requirement for ongoing investigations and development. Pre-dewatering commenced in October, 1984. Purpose designed pumping trailers have been employed to minimise the loss of pump availability resulting from the frequent. need to remove and reinstall pumps when close vicinity blasts occur. To July, 1986, some 0.5 Mm' of groundwater had been pumped from the unconfined orebody aquifer. Mining has progressed to some 20 m below the standing water level without. any undue water associated problems. Ultimately, it is ,cheduled to extend some 300 in below the original water level in the West Pit. With the development of an increasing area of the mine below the standing water level, the influence of seasonal high intensity rainfall events, which had previously caused little concern, now need to be addressed. Pumping equipment has been designed to evacuate storm water at a rate consistent with mine production Considerations.

Jan 1, 1986

By Readett D. J

Soluble salts can be removed from Bowmans lignite by water and acid leaching. The success of the removal of water soluble or acid exchangeable impurities is directly associated with the efficiency of dewatering these slurries. The filtration characteristics of a slurry at its natural pH (4.0) were poor, with a filter cake moisture of 65%. Acid treatment of the slurry at pH2 caused the filter cake moisture content to drop to 61 %. Various oils, oily surfactants and a flocculant were tested to determine the conditions for minimum filter cake moisture. A series of pilot scale filtration tests were conducted on flocculant dosed slurries with and without washing on a horizontal test unit. Moisture contents of 54% were obtained in laboratory testing using high additions of oily surfactant. For the pilot scale test work, moisture levels close to 60% were obtained with low flocculant additions, similar to results obtained in laboratory studies. Removal of soluble salts could be correlated directly to the final moisture content of the filter cake. This process of leaching followed by filtration resulted in the removal of approximately 75% (more than 80% with washing on the cloth) of the sodium chloride originally present in the lignite.

Jan 1, 1989

By Soma T

Pyrite and Cu-concentrate were roasted in vertically suspended state in an externally heated tube. Tubes of three different lengths of reaction zone were used for three different reaction times. Roasted ores were submitted to chemical analysis and the extent of roasting reactions was determined. In case of pyrite, extent of roasting reactions was not affected much by reactor length and heating temperature (above 500¦C), but was considerably by ore/air ratio. Micro- scopic and XMA examinations led to the conclus- ion that pyrite particles decomposed to pyrrho- tite and then pyrrhotite was oxidized to give Fe-S-0 melt, magnetite and hematite. The extent of reaction was not uniform in all particles but had a wide distribution from unreacted pyrite to completely oxidized particles. Combustion of Cu-concentrate from Kuroko complex sulfide ore ) was unstable under a uniform wall temperature of 450¦C, but proceed- ed rapidly at temperatures above 500¦C. Sticking of roasted ores to the wall of the reaction tube induced choking of the tube, caused by melting of roasted ores, at tempera- tures above 950¦C. Enrichment of oxygen exterted less influence on reaction rate than heating temperature of the tube. Particle size of ore had a big effect on reaction rate.

Jan 1, 1980

Arrow Energy NL has been operating a number of coal seam gas wells in the Darling Downs region of Queensland. At the time of writing this paper, the region is enduring an extended drought period. The local aquifers are depleting and have not been significantly recharged in over a decade. The local communities (both rural and townships) are struggling to obtain water. Currently, coal seam gas (CSG) operators (under licence) draw water from the coal seams as part of the gas production process and the majority of operators choose to evaporate this water, as it is characteristically brackish to saline in quality and as such must be contained. Although the water produced from one CSG operator is not sufficient to drought-proof the greater area of the Darling Downs, there is potential to supply smaller local areas and contribute to the sustainability of these communities. This paper outlines the work completed by Arrow and its local community partners on the Darling Downs to date, and discusses the application of the produced formation water for:stock watering in feedlots, as a feedstock for coal washing, as a potable water supply for Dalby, as an agricultural water supply for cotton farming, and use as a medium for growing salt-water fin fish.

Jan 1, 2006

By Hampshire MJ

The tailing retreatment project rated at 10 000 t/day commenced operations in October 1982. The operation consists of dredging, feed preparation, cyanide leaching and carbon-in-pulp (CIP) gold recovery followed by Zadra atmospheric stripping and electrowinning. For the first two years the operation was adversely affected by excessive cyanide consumption and low gold extraction. Investigations demonstrated that the very fine, or slime, fraction of the tailing was the dominant consumer of cyanide and dissolved oxygen. The plant flowsheet was subsequently modified by inclusion of 80 - 100 mm dia. cyclones for slimes separation and a 31 m dia. thickener for water recovery. Treatment of deslimed feed in the CIP plant has reduced sodium cyanide consumption from an average 1.85 kg/t to 1.15 kg/t. The reduced oxygen consumption by the CIP plant feed has resulted in higher dissolved oxygen levels, frequently reaching supersaturation after 4 to 5 h contact time. This has allowed much improved gold extraction from the existing CIP plant capacity. Gold extraction from the mixed pyritic siliceous tailing has improved from an average U prior to desliming to a current 57%. Investigations are continuing on the recovery of gold from the discarded slimes.

Jan 1, 1986

By Li YQ, Yoon RH

The photoresponse of natural mineral pyrite and galena electrodes has been studied in aqueous solutions on freshly fractured surfaces (some fractured in situ) using moderate overvoltages. When fractured in situ, the electrode potential of both minerals instantly drops several tenths of a volt. Pyrite exhibits a spontaneous anodic photocurrent at fracture, which indicates upward band bending (depletion layer) on the n-type electrodes. The negative surface charge responsible for the depletion layer is believed to arise from a surface state that is intrinsic to pyrite surfaces, possibly modified by hydroxide ion adsorption. The flat band potential, Vty, of pyrite is at approximately -1.0 V (SCE) at pH 9.2 but to reach V(b, pyrite has to be cathodically decomposed. In contrast, galena assumes the flat band potential at fracture. Subsequent polarisation of galena at potentials positive of Vth produces an anodic photocurrent (upward band bending) and polarisation negative of Vro a cathodic photocurrent. Most of the galena electrodes studied were degenerate n-type and at potentials negative of Vtb, no cathodic photocurrents are observed, indicating the bands cannot be bent downward, consistent with the Fermi level at the surface merging with the conduction band edge near Vn,. Several were close to intrinsic, with the photocurrent changing sign near Vn,.

Jan 1, 1993

During the last few years the quality requirements on roads and railroads have become more accentuated due to the desire to minimise maintenance costs. This has, in turn, led to increasing requirements in the preparation of ballast materials and pavement aggregates. As the access to natural gravel in northern Europe is decreasing (due to lack of availability or by law restrictions) the use of crushed rock material is becoming more and more important. The aim of this paper is to derive and describe a universal method for the prediction of particle size distributions from compressing crusher machines such as jaw- and cone-crushers. Based on a closely defined physical model, expressions which define the size reduction process are derived. Conditions for simplifying assumptions are clearly outlined. The choice and mix of breakage functions is a central subtopic iò the analysis of the crusher machine processes. Known breakage functions are reviewed and evaluated. A new concept for determination of a true breakage operator which is related to physical properties of the crusher device and the size distribution of the feed material is introduced. Finally experimental tests are compared to numerical calculations. The method described in the paper can be a useful tool when designing crushing plants or when optimizing the output of compressing crusher Machines.

Jan 1, 1995

By P Bonniwell

As a part of the Newcrest, Telfer Expansion Project, a consortium of Australian, Canadian and South African Mining Contractors in joint venture have been contracted to develop the hoisting shaft. The parties namely; Byrnecut Mining Pty Ltd, Murray and Roberts RUC and Thyssen Mining Construction of Canada Ltd have combined their individual expertise to excavate the shaft. There is a particular emphasis on the use of proven shaft sinking techniques from North America and in particular integrating electric hydraulic drilling equipment and personnel from the Canadian Mining industry. The Telfer hoist shaft when completed will have a finished diameter of 7.1 metres and extend to a depth of 1170 metres below the collar. The shaft will be fully concrete lined and will later be equipped for hoisting ore from the Telfer deeps at a rate of five million tonnes per annum. The shaft when completed will be the largest shaft ever completed in Australia on a volumetric basis. This paper will examine the technical aspects of the shaft sink, as well as exploring the integration of personnel and equipment from the frozen prairies of Saskatchewan, Canada into an operation in the Great Sandy Desert of Western Australia. What are the spin-off benefits for the development of other shafts within Australia?

Jan 1, 2005

Broken Hill has a long history of mining and it is without doubt a world-class deposit. It has seen production since 1885, notwithstanding the strikes that made the city infamous in days gone by and has given rise to three of the nation's leading mining companies; BHP, North and CRA. Prior to the formation of Pasminco in 1988, the mining and exploration activities were undertaken by separate companies who were business competitors and tended to operate in relative isolation. There were a few notable exceptions such as the Central Geological Survey of 1936 - 38 (Gustafson, 1939; Gustafson et al, 1950) and the Mine Managers' Association. The latter sponsored many university based research projects. At a local level there was good communication and cross fertilisation within this remote outback centre through personal contacts and professional bodies such as The AusIMM. Pasminco was formed by the merging of the lead-zinc interests of CRA Ltd and North Broken Hill Ltd. In Broken Hill this meant the joining together of North Mine and ZC Mines, the two largest mines then operating on the Line of Lode, to form Pasminco Mining Broken Hill Operations. The exception was the central part of the orebody, the original BHP, South Mine and

Jan 1, 1997

By Corbett GJ

The Bulolo Graben represents an intra-arc rift formed by activa- tion of transfer structures in an extensional setting formed be- tween the eastern and western sectors of the New Guinea Origin. Crustal thinning has facilitated the emplacement of dacitic Edie porphyry intrusions, locally as flow dome complexes, phreatomagmatic (diatreme) breccias and the Bulolo ignimbrite/ agglomerate as an extrusive equivalent of the Edie Porphyry. Gold mineralization is localized along intra-graben structures, com- monly at the intersection with cross structures and occurs in sub- sidiary dilational fractures and not the localizing major structures. Gradations are apparent in the styles of mineralization according to the degree of erosion of the hydrothermal system. Hamata occurs as the deepest mineralization of the quartz-sul- phide style Wau, Hidden Valley, and Edie Creek are dominated by carbonate-base metal styles. Kerimenge grades from quartz sulphide through carbonate-base metal to epithermal mineraliza- tion, the latter style also being present in the periphery of Edie Creek. Here, pre-existing fractures of the Edie Creek Structural Corridor have been reactivated by movement on NS structures to form the ore-hosting dilatant lodes. Fluid flow may have been from the vicinity of the Nauti diatreme margin and along the vein System.

Jan 1, 1997

Tourmaline-bearing rocks are a rare rock type of Suites 3, 4 and 5 at Broken Hill. Minor laminated plagioclase-quartz-tourmaline rocks occur in association with the quartz- magnetite rocks of Suite 3 with the greatest abundance of tourmaline-bearing rocks present in Suite 4 intimately associated with lode horizon, scheelite mineralisation and zinc mineralistion - all approximate strike equivalents of the Broken Hill Pb-Zn-Ag deposit. Bedded quartz-tourmaline rocks, tourmalinites, tourmaline-rich pelite and tourmaline-bearing lode horizon have been recorded from suite 4. The bedded tourmaline rocks rarely display cross bedding, graded bedding, slump structures and small scale intraformational breccias. Minor tourmaline-gahnite-bearing pelites are present in Suite 5. The sedimentary structures, metamorphic textures, the stratigraphic position of the tourmaline-rocks and the presence of quartz-tourmaline-gahnite-spessartine (-fluorapatite) lode rocks indicates that the mineralisation at Broken Hill and the tourmaline-rich rocks are all products of submarine exhalative hot spring systems which were most active during deposition of Suite 4 rocks. Tourmaline is chemically different from that associated with granitic activity and from other submarine exhalative tourmaline-rich rocks because the premetamorphic alteration at Broken Hill involved addition of Fe, Ti and F and subtraction of Mg - a feature reflected in the chemistry of tourmaline from Broken Hill.

Jan 1, 1983

By R Buerger, D Barrett, P Hodkiewicz

The Emily Ann nickel mine is owned and operated by LionOre Mining International Ltd. The deposit was discovered during 1997 and is blind, concealed beneath 25 m of transported cover and a further 100 m of unmineralised Archaean felsic rocks. Nickel sulfide mineralisation is hosted predominantly in strongly deformed, altered and metamorphosed Archaean komatiitic ultramafic rocks. Subordinate felsic-hosted, remobilised mineralisation is also present. Mining of ore commenced during late-2001. Since the early days of exploration drilling, through feasibility delineation drilling and subsequent mining, a geological model involving thrusting and folding of a komatiitic-hosted nickel sulfide deposit has been an evolving theme. Development of appropriate mine geology procedures, including detailed mapping, significantly increased the confidence of mine-site geology and engineering staff in the geological model and improved operational efficiencies during start-up. This also allowed the engineering and mining team to develop a tolerance for the large fluctuations in daily production grade, with an understanding that budgeted production targets, on a level-by-level basis, were achievable. This paper describes the development of the current interpretation of the deposit and emphasises the importance of a sound understanding of deposit geology. The direct benefits at Emily Ann included improvements in drill targeting, resource estimation and mine planning.

Jan 1, 2003

By Johnson RW, Rogerson R

New perceptions of the nature of volcanic hazards on Bougainville Island have resulted from a recent remapping of the geology of the island. Ignimbrites and calderas have been identified at six Quaternary centres (Emperor Range, Tore, Kunua, Billy Mitchell, Loloru, and Laluai), and large-scale explosive activity now must be identified as a significant volcanic hazard on the island. Billy Mitchell and Loloru volcanoes are identified as the most likely sites of future, major, explosive activity. Billy Mitchell was recognised formerly as an extinct volcano, but is now known to have produced major eruptions 370 and 918 years BP. Five ignimbrite units recognised at Loloru range in age from about 12 700 to 3200 years BP. Bagana is an active volcano in central Bougainville, but its explosive activity is relatively minor and does not significantly affect areas beyond the uninhabited area of the volcano itself. Balbi is the largest volcano on Bougainville and has an extensive geothermal area at its summit. It was thought to have been in eruption last in the early nineteenth century. However, 370 and 940 year BP plinian ashfalls from Billy Mitchell cover the central area of Balbi, so the latest significant activity from Balbi may have been at least 1000 years ago.

Jan 1, 1990

Discovered in 1954 and mined since 1966, the X41 copper orebodies have produced over 143 Mt @ 3.3 per cent copper. By June 2002 the production from these orebodies had depleted the Mineral Resource to 36.6 Mt @ 2.8 per cent Cu (including 31.5 Mt @ 2.5 per cent Cu combined 2002 Ore Reserve). Mine production will ramp down to cessation beyond ten years. The 2002 Copper Business Study was commissioned to review the status of the Mount Isa copper business and to optimise the long-term strategy of the operations. The study resulted in a vastly improved geological and geostatistical model, and financial studies led to the optimisation of mine cut-off grades. Utilising these new models, a near-mine target generation workshop was conducted by the copper stream geology team. The workshop focussed on exploration for new ore sources and the extension of existing orebodies to supplement the Mineral Resource inventory for future conversion to Ore Reserves. Several prospective targets were identified and the Conceptual Northern 1100 Drilling program was subsequently designed. This paper shall discuss the practicalities of near-mine target generation in Mount Isa, the issues faced when locating and preparing drill sites in a mature mine environment, and the preliminary results of the drilling program so far.

Jan 1, 2003

Callie underground gold mine is part of the Newmont Tanami Operations, and is now the primary provider of ore to the Granites processing Mill. The Callie underground mine has produced in excess of 7.6 million tonnes (Mtpa) of ore, since production began in 1998, with a current production rate of 1.9 Mtpa. Callie underground uses sublevel open stoping with extraction through a combination of primary and secondary stopes. The primary stope filling strategy utilises cement aggregate fill (CAF) to allow full recovery of secondary stopes. The Callie backfill operation has had a continuous testing program in place during this time, which has resulted in a great deal of information available for post fill analysis. All CAF placement into primary stopes for Callie has been via surface boreholes and this has given Callie mine an understanding of some of the issues related to borehole design, type of linings to use depending on angle, depth and quantity of fill into stopes. Finally backfill barricades at Callie have undergone a number of changes during the time to optimise the design based on whether CAF or sand fill is used. This paper discusses the CAF backfill practices and testing methods used for backfilling operations at Callie.

Jan 1, 2005