Search Documents

By A Rojc, J Ronaszeki, C Smith

Nuclear logging was tested for the in situ determination of Fe, Si, and Al in iron ore blastholes with field tests at the BHP Billiton Iron Ore, Mount Waleback Mine. Prompt gamma neutron activation analysis (PGNAA) was used to determine percentages of Fe and Si while natural gamma logging was employed for the determination of Al. The accuracy given by nuclear logging is comparable to the accuracy provided by the laboratory analysis which was determined by taking the average of four samples collected from the cuttings deposited on the surface around the perimeter of a drill hole. The work also indicated that there is a chance of determining Al by PGNAA.

Jan 1, 2002

An account is given of experimental apparatus for generating a short duration high velocity water jet and the effect of its impingement on various rock samples under air or water cover. The penetration was found to be highly dependent upon the rock structure; in general material with closely interlocking grains was resistant.The damage sustained by a stationary sample held close to the jet did not vary greatly whether the sample was in air or confined under a water layer; but when the sample was translated under the jet there was a marked increase in the damage sustained.Some consideration was given to the possible practical application of a water jet for deep hole drilling and an estimate made of the power requirements and transmission losses for such a system.

Jan 1, 1969

By C A. Heinrich, J L. Walshe, V J. Wall

The Porgera Gold Mine, located in the highlands of Papua New Guinea, has produced over 5 million ounces of Au, since its opening in late 1990. The deposit is located within Upper Cretaceous Papuan Platform sediments approximately 25 km south of the Lagaip Fault, and is spatially and temporally associated with the 6 Ma alkaline Porgera Intrusive Complex.

Jan 1, 1995

By Napitupulu P

PT Freeport Indonesia currently operates a concentrating complex capable of milling 127 000 metric tonnes per day of copper and gold hearing ore. The facilities consist of both a conventional crushing, ball mill and flotation circuit and a SAG, ball mi

Jan 1, 1997

By W. J. LANGRON

This paper describes the results of VLF-EM test surveys, using the Ronka EM-16 equipment, over a selection of environments in Australia and Papua.Using comparisons with known geology, drilling information and other geophysical work it is shown that the maximum depth of penetration of the method is about 100 ft but is considerably less than this in most areas.The author believes the method could aid in geological mapping and provide a useful adjunct to aeromagnetic surveying in some areas.

Jan 1, 1972

Up to 19 chemical parameters were studied in flotation pulps in six Australian lead-zinc concentrators with the aim of obtaining a better understanding of the nature of, and changes in, the chemical environment. This paperdiscusses pH, redox potential, and oxygen concentrations, which were all measured continuously.Two plants operated at natural pH in slightly acid circuit and one at natural pH in alkaline circuit, and pH was stable at all these plants. In two plants varying amounts of cement fill were present in mill feed and pHwas variable. At the other plant pH was controlled with soda ash and lime.Redox potentials became more positive as the pulp passed through the plant. The minimum change was 20 mV and the maximum about 250 mV. Potentials tended to be variable at any point early in the circuit, but were more stable later on. In some plants reagent additions had no noticeable effect on redox potentials. However in the two plants operating in acid circuit the redox potential of .zinc rougher feed was markedly affected by changes in copper sulphate addition rate. Sodium sulphite additions had an effect at other plants.Oxygen concentrations in grinding circuits tended to be low (30 per cent of saturation) and very variable. Flotation was usually conducted in pulps at least 90 per cent saturated with oxygen. Addition of sodium sulphite had a marked effect on oxygen content in one plant, but less effect in two others.Statistically significant relationships were found in some plants between pH and redox potential, redox potential and oxygen saturation, and oxygen saturation and pH.Improved control of copper sulphate and sodium sulphite additions could result from applications of this work.

Jan 1, 1970

By S Sabanov

Determining ventilation system model inputs from the field test work has been produced in the working oil shale mine which has been in production since the early 1970s. At this mine room-and-pillar with drill-and-blast methods are used. The mine has a complicated ventilation system to supply fresh air for the eight mining production areas on the radius of about 12 km. The main purpose of the experimental test works was to obtain data for estimation of an optimum cross-section area for a new ventilation shaft. Experimental test works included measurements of air volume and fan pressure using five different modes of intake air through the ventilation shafts system. Measurements of airway friction factors were obtained during the ventilation surveys to determine characteristic friction factors for the intake airway. The results of the measurements will be used for further air flow simulation processes required for design of new additional ventilation shafts in the oil shale mine. Results of the study can be useful in estimation of frictional pressure drop in oil shale mine conditions.CITATION:Sabanov, S, 2017. Determining ventilation system model inputs from field test work in the oil shale mine, in Proceedings Australian Mine Vent Conference 2017, pp 47–50 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

Electrochemical Behaviour of Massive Chaclopyrite Bioleached Electrodes in Presence of Acidithiobacillus ferrooxidans and Acidithiobacillus caldus In this work, the monitoring of bacterial and chemical dissolution of massive chaclopyrite was evaluated using cyclic voltammetry (CV); the mineral surface was examined using scanning electron microscopy (SEM) and the elements were examined by Energy Dispersive X-ray Analysis (EDAX). The electrolyte employed for the electrochemical tests was the medium used to bioleaching the electrodes (3.0 g/L (NH4)2+SO4, 0.5 g/L K2HPO4, 0.5 g/L MgSO4+7H2O and 0.1 g/L Ca(NO3)2).The results showed differences in voltagramms carried out by Acidithiobacillus ferrooxidans and Acidithiobacillus caldus: In bioleached electrodes tested in the presence of Acidithiobacillus ferrooxidans, the anodic and cathodic current signals were larger than with Acidithiobacillus caldus. The analysis of CV results allowed attributing the different peaks observed in both the direct and reverse potential scanning to the oxidation of chaclopyrite to a secondary copper mineral (bornite, chalcocite and covellite) and its reduction via different non stoichiometric copper sulphides intermediaries. Surface evidences were observed by SEM, and chemical elements evidences were also investigated by EDAX.

Sep 13, 2010

By J W. Muir, N Bedford

Hong Kong is one of the most rapidly developing cities in the world. With constant population growth and limited opportunities for space, the development of a fast and effective underground public transportation network is essential. Hong Kong’s Mass Transit Railway (MTR) Corporation is currently undertaking several large underground expansions to its existing network. Much of the excavation will be carried out using the drill and blast excavation method.Drill and blast excavation is common in Hong Kong and with the continued development of underground infrastructure the use of the drill and blast excavation method will increase. Although an effective method of excavation, the blasting vibrations caused during construction can have an adverse impact on surrounding structures and impose disruption on the local community.In order to minimise the risks associated with blasting vibrations, and to demonstrate that the impact on local stakeholders will remain within acceptable limits, it is generally necessary for a contractor to submit a blasting assessment report for approval by government authorities before blasting may commence.Continued increases in population density will force more infrastructure to be constructed underground. Tunnels and caverns are increasingly excavated in closer proximity to critical sensitive receivers. This leads to greater potential impacts on the community, tightening constraints on contractors and a higher level of confidence required for approval authorities. Finding a balance between the needs of the community and rising construction costs becomes more challenging.This paper presents a case study on how the blasting assessment report process has been successfully implemented for a major MTR project situated in a densely developed area of Hong Kong. It describes several methods of assessing blasting vibration impacts, innovative uses of blasting for excavation and the mitigation measures employed to provide the best outcome for all project stakeholders.CITATION:Bedford, N and Muir, J W, 2014. Blasting vibration assessment and innovative blasting methods in high-density urban environments, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 9–20 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

CONTENTS: Broken Hill The mixing stations.Operating and mixing apparatus.Pulp distribution.Stope preparation.Filling procedure.Consolidation of old fill.Drainage:Pulp density tests. Life of sand pipe lines.Results.Advantages and disadvantages.Conclusion and acknowledgments.General remarks on South Limited.Mining methods.History of stope filling in Broken Hill.Need for a new and better filling method and transport system.Initial experiments with hydraulic stowing.Source of the sand.Water Supply.Signalling system.GENERAL REMARKS ON BROKEN HILL SOUTH LIMITEDThe South Mine, property of Broken Hill South Limited, is situated at Broken Hill, N.S.W., Australia, towards the southern end of the main lode.The leases (M.L's 7 and 8)' cover a length of 2,400 feet along the lode outcrop and the workings extend, at this date, to a depth of 1,940 feet below the collar of the original main shaft and to 825 feet below sea level.Mining operations have been continuous for about 58 years and during this period nearly 12.5 million tons of ore have been mined. The monthly tonnage extracted approximates 30,000 tons in normal times.The ore is a mixed sulphide containing galena and marmatite; the gangue minerals are principally calcite, rhodonite, quartz and garnet.A typical assay for a monthly period is 14·40/0 Pb., 5·6 ozs. Ag., and 11· 60/0 Zn. The whole of the ore is concentrated on the property by combined gravity and flotation methods. The lead and 'zinc concentrates produced are railed to other centres for the extraction of the contained metals.MINING METHODSMining practice throughout the field varies only in minor details. The ore-bodies forming the Broken Hill Lode lie within complex folds arranged along a shear and vary in size and mineralogical associations, but all the mines have similar types. Some of the ore-bodies have weak walls, but the chief difficulty in mining is caused by "heads" and "flaws" in the ore.Besides these local weak areas there are ground movements-referred to later-of varying magnitude extending throughout the central portion of the lode where the large ore-bodies, several hundred feet wide, approached the surface.

Jan 1, 1944

Paiam is a new township in the high mountains of Papua New Guinea built in association with the Porgera Joint Venture mine, one of the world's largest and most remote open cut gold mines. The Paiam town project is an interesting and genuine attempt at building sustainability into a community associated with a mine. A result of a tri-party agreement between a resource developer, government and land owners, this town is a good example of appropriate utilisation of benefits, obtained from resource development, directed at achieving a sustainable environment at local and regional levels.   Mining brought technology and income to the region, although as most mine staff fly directly in and out, local landowners considered there was a limited flow of benefits within the nearby townships. An agreement with government and mine was reached that more mine personnel and their families be housed locally. In 1998, we, a firm of Landscape Architects and Heritage Consultants based in Cairns, Queensland, were engaged to assist develop the fledgling town of Paiam into a livable and sustainable town and to produce material that would convey that information to stakeholders.   The design focused on establishing a sustainable town, with livability, urban form, aesthetics and opportunities for economic, social and cultural development. Aiming to be a livable town for locals and mine staff it included a market place designed as a focus for town life, essential for social cohesion and economic opportunities.   Located at 2200 m on steep rainforest clad topography, the town development has been laid out using an appropriate urban form based on organic village layouts. Clusters of houses allow for a common public area so children's play is monitored assisting with a sense of community similar to a traditional defensible village. Aesthetical consideration helps in developing community pride whilst maximising potential for development of a tourist industry.   Opportunities for ongoing economic development were incorporated in the design and construction process. These included developing skills and trades to service the region and to provide skills, development, income opportunities and infrastructure to last beyond mine closure. Administration procedures were set in place to form the basis of good governance.   The shift from traditional subsistence lifestyle to a sustainable community with traditional attributes was the project's goal and is being achieved.

Jun 1, 2010

By R Jacobs, J Yeates

"The Stockman base metals project is situated in State Forest in the alpine area of East Gippsland, Victoria, adjacent to a National Park and within the headwaters of a major Ramsar-listed wetland catchment and the Murray-Darling River system. Site topography is steep, and elevated (650 m – 1200 m above sea level), and subject to circa 1 m annual rainfall, with occasional winter snowfall. The project consists of two volcanogenic massive sulfide (VMS) deposits to be mined by underground methods and treated in a 1.0 Mt/a central concentrator to produce copper and zinc concentrates for export over a ten year operational life. New resource projects are rare in Victoria. Recognising the sensitive setting, planning for the Stockman Project, which is now in the advanced permitting stage, has focused on balancing economic, environmental and social outcomes to ensure social licence to operate is secured and can be maintained. This has involved close attention to triple bottom line (TBL) risks and outcomes. Stockman has successfully gained State and Federal approvals via the Environmental Effects Statement process. The process of obtaining these approvals has required close attention to effective stakeholder involvement, and management of a lengthy and difficult approvals process, which is still to be finally concluded. This paper is a case study of the process of that permitting and the issues encountered to date. Key learnings from the experience have included: successful approvals require close attention to much more than just the project and its technical aspects and physical setting – effective stakeholder involvement and endorsement is critical the differing consultation requirements for local, regional and government stakeholders, to design and plan implementation of a project to meet TBL objectives, and to gain social licence to operate within the Victorian approvals process, the need for an effective lead government agency with policy authority dealing with material policy change requiring post-closure financial sureties estimating realistic permitting time and cost during the project evaluation phase. CITATION: Jacobs, R and Yeates, J, 2016. Stockman base metals project – sustainability, social licence to operate and permitting lessons learnt, in Proceedings Project Evaluation 2016, pp 98–110 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

That electricity is an important and valuable agent, the limit of whose capacity for utilisation is as yet unknown, is a truism; although enormous advances have been made, the possible developments are yet greater. Mining, along with other industries, shares already to a large extent in the practical utilisation of this agent. Electrical engineers have been employed for several years past in developing and applying electricity to all classes of machinery, and for every purpose where power is required and in no instance, that the writer is aware of, has its use been curtailed in favour of any other agency now known, while extensions are continually made. The first modern electric motor was shown at the Vienna Exhibition of 1873, and it was used to work a pump through a mile length of cable but it was not before 1878, that an electric motor was put into daily commercial use by Messrs. Chretian and Felix to work a beet sugar hoist. This early plant effected a saving of 40 % as compared with hand work.In 1879, the first Electric Railway was constructed for the Berlin Exhibition, and in the same year, Mr. T. A. Edison was running an experimental line at Menlo Park. The first electric line opened for the public, was constructed by Siemens and Halske, in 1881, at Lichtenfelde, and was 11 miles in length.

By M Lee, J F. Carswell, G Reitsema

"The increased costs of underground mining have continually challenged engineers to identify opportunities for alternatives to common approaches to underground development. Considerations to the design of horizontal and vertical development at the Dugald River mine targeted inclined raise boring to reduce horizontal development, not only to reduce cost, but to allow development activities to focus on other areas of the mine.The mine plan consists of 50 raise bored ventilation shafts, of which 17 have been mined to date with diameters ranging from 3.1 m to 5 m and lengths from 30 m to 200 m. The expected performance and stability of these shafts has been determined using methodologies proposed by McCracken and Stacey (1989) and further refined by Peck, Coombes and Lee (2011). Actual raise performances have been collated and compared to a database of raise bore performances across Australia as presented by Coombes, Lee and Peck (2011), and form a database of raise bore performance specific to Dugald River.Opportunities to further optimise the mine plan and reduce costs have seen the introduction of large diameter-inclined raise bored ventilation shafts to minimise the required lateral development to connect the ventilation circuits. Large diameter inclined shafts ranging between 3.1 m and 4.5 m in diameter have been successfully mined with dips down to 70°, reducing the cost of lateral development by more than $1 million over the next two years.Both technical and operational challenges were overcome in the mining of large diameter-inclined raise bores, including modification of: existing methodologies of assessing shaft wall stability for inclined raises. These included variations of the McCracken and Stacey method and the utilisation of the modified stability number (N’) previously developed for stope performance (Potvin, 1988). both the collar and toe development profiles, including the general set-up of the raise bore drill rig to reduce the operational risks associated with angled raises.Due to their success, inclined raises have been designed for subsequent stages of the life-of-mine ventilation system at Dugald River. This has resulted in significant capital cost savings for the mine.CITATION:Carswell, J F, Reitsema, G and Lee, M, 2017. Vertical and inclined raise bore performance at Dugald River mine, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 313–320 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 16, 2017

By G J JAMESON

The flotation cell has undergone a number of changes since the process was first introduced in Broken Hill in the early years of this century. The development of the mechanical flotation cell is reviewed, followed by a discussion of more recent developments such as the flotation column, the air-sparged hydrocyclone, the Wemco-Leeds cell, the Bahr and Deister columns and the Jameson cell.

Jan 1, 1992

How Particles Stick to Bubbles - The Influence of pH and Hydrophobicity in Flotation

Sep 13, 2010

Removal of Arsenic in Fluorite Ore by Simultaneous Grinding-Leaching with NaHS Generally speaking, a high-grade fluorite ore is converted into hydrogen fluoride (HF), which is essential for the semiconductor manufacturing. With the continuous depletion of resources, novel technologies for processing low-grade fluorite ores are urgently needed, in order to lower the arsenic concentration to less than 100 mg/kg. In this study, a low-grade fluorite ore was upgraded by removing arsenic, which is difficult to remove by conventional method. The mechano-chemical leaching of fluorite ore (i.e. the sample was ground in presence of NaHS, using a beads mill) was carried out to investigate the removal of arsenic from the low-grade fluorite. Experimental results showed that the arsenic concentration was reduced to 73.2 mg/kg.

Sep 13, 2010

During a mineral exploration program in an environmentally sensitive area nearMount Painter in South Australia, a helicopter was used to position, construct and service drilling rigs in order to avoid the need to create new access tracks. The drilling program was designed to optimise the advantages of natural landforms in order to minimise the environmental impact of site construction and drilling activities. This minimisation of land disturbance reduced the required amount of rehabilitation measures to the extent where all impacts of the helicopter-supported programme had disappeared within 12 months of completion of work.

Jan 1, 1995

By J Johansson, B Johansson

The mining industry needs to attract and recruit young talented people. An important task is, therefore, to create an attractive mining workplace that engages with, and motivates youngsters who are not particularly interested in working in the industry. This paper aims to illustrate a way forward for the mining industry to form healthy and safe workplaces honouring key components such as knowledge, skill, co-operation, continual development and acceptance of diversity. This is a way to create a vision of healthy and safe mining work. The mining industry must work towards zero vision; a future without accidents and hazardous environments. In this paper the authors discuss different aspects of an ‘attractive workplace’ and summarises lessons learnt in 26 statements dealing with safety, both physical and social work environments, and social responsibility. The authors hope these recommendations will provide some guidance for how attractive workplaces should be designed for future deep mining.The paper is based on lessons from two large European projects, a Swedish-Polish project: The Smart Mine of the Future; and a European Union project: Sustainable Intelligent Mining Systems (SIMS). One of the authors was the WP leader of health and safety in both projects.CITATION:Johansson, J and Johansson, B, 2017. Attractive workplaces in future underground mining, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 99–102 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By S Thomas, S Ricketts, R Hassell

Northern Star Resources (NSR) operates several operations utilising narrow vein stoping operations in the Kundana area. Stope dilution performance is variable across these operations, with unplanned dilution reducing individual stope economic viability, increasing risk to personnel and machinery operating in and around the stope and delaying the overall stoping sequence. Technical investigations were undertaken to objectively understand the variables which had the largest impact on stope performance and then use the findings to help develop mining strategies to reduce dilution. A stope reconciliation process was developed to compile key stope performance information such as stope design parameters, geotechnical and drill and blast factors. These were compared against the measured dilution. Production targets necessitated a high turnover of stopes in the operations, and hence a requirement for an expeditious process and mine design software with automated tools. The output of these results, together with numerical variables from geological, geotechnical and drill and blast data were analysed via multivariate regression. The analysis identified the factors with the greatest influence over stope dilution, and a forecast model was consequently created. Confidence was gained in the model when the subsequent stopes performed in line with prediction. Different drill and blast designs were subsequently trialled and found to reduce dilution. The model was then updated with the new practices, facilitating further regression analysis to identify revised key controlling factors. The subsequent production results however, displayed a poor correlation with the prediction from the revised model. Inconsistencies in drill and blast designs and execution were identified as key factors in the dilution performance. This was an important finding as the correct implementation of the design is critical and this has become a key focus for future stoping. Overall the technique presents an objective process to identify causal factors of stope dilution resulting in improved economic metrics for stope production. The process will be applied to other similar Northern Star operations.

Mar 15, 2021