Search Documents

By H Ishikawa, S Palaniandy

The gravity-induced stirred mill such as the TowerMill is an energy-efficient grinding solution used in secondary, tertiary, and regrinding duties in the mineral processing concentrator. The interest in this technology is emerging, with more than 300 mills installed globally in various grinding duties and commodities for the last 30 years. Although the technology is matured, there are still opportunities for improvement and the development of new knowledge to improve its circuit energy efficiency and reduce water consumption. Recent studies show that a combination of stress intensity, ore hardness, slurry density, and mill feed configuration can be used to evaluate the performance of the grinding circuit. A recent pilot-scale TowerMill test work at various stress intensities shows that a lower operating work index and size-specific energy were achieved at higher agitator tip speed and using medium size grinding media. These outcomes were confirmed through several site trials. A smaller 17 mm grinding media has reduced the operating work index and size-specific energy by 18 per cent and 11 per cent, respectively, compared to the 20 mm in a magnetite concentrator. Moreover, the conversion from top feed to bottom feed configuration has reduced the operating work index and size-specific energy by 13 per cent and 37 per cent, respectively. The circulating load was reduced by 34–38 per cent, leading to a reduction in the dilution water consumption in the hydrocyclone feed sump by 20 per cent. A variable frequency drive offers flexibility to change the stress intensities on the TowerMill, where a 35 per cent reduction in specific energy was achieved when the ore became soft. This paper explores the potential design and operating strategies that can be implemented to enhance the energy efficiency, reduce water consumption and reduce CO2 emissions in the circuit and finally evaluate its impact on the total cost of ownership.

Aug 24, 2022

By Kelly D, Moore C

The Golden Mile, which has been mined continuously for the past 100 years by both underground and more recently open pit methods, occupies an area of 1.2 km by 4 km adjacent to the city of Kalgoorlie Boulder in Western Australia (Figure 1). Large-scale open pit mining at the Kalgoorlie Consolidated Gold Mines (KCGM) Fimiston operations is currently extracting 7.8 million tonnes of oxide and sulphide ore for a total production of 522 000 oz per annum. The effectiveness of grade estimation techniques at KCGM has been examined with reference to existing 10 m bench sample data from all operating areas within the Eastern Lode System of the Main and North pits. The aim of the study was to recommend practical parameters for grade control estimation. The review included comprehensive variography and comparison of nonparametric estimation methods (Joumel, 1983) such as indicator kriging and probability kriging with ordinary kriging, leading to the development of improved grade control parameters and procedures for both daily quality control and short term mine planning. This paper reviews the geological, statistical, geostatistical, mining and modelling features studied in order to present KCGM's Mining Department with recommendations for improving grade control.

Jan 1, 1994

By D Oliveira

The use of an equivalent continuum for a rock mass is not always suitable for situations where the failure is structurally controlled by discontinuities as in the case of wedges in the tunnel roof. In these instances, discontinuum approaches are usually preferred. Rock joints that are filled with soft infill are likely to be the weakest planes in a rock mass, having a dominant influence on its overall shear behaviour. In this case, the joint material model adopted for the discontinuities should be able to describe important mechanisms, such as asperity sliding and shearing, post-peak behaviour, asperity deformation, and the effect of the soft infilling. The latest version of a soil-infilled joint model is discussed here. It describes more comprehensively than previous models the occurrence of dilation and compression with lateral displacements, and also represents the hardening mechanism related to asperity interference as observed in the laboratory that cannot be readily captured by the existing joint models. An analytical approach for the analysis of rock wedges structurally controlled by soil infilled joints is presented.The analytical approach presented in this paper for assessment of symmetric rock wedges in the roof of a tunnel demonstrates, that the peak shear strength of the joint may not be fully mobilised before detachment of the wedge. The analysis verifi ed that an overestimation of the factor of safety may be observed when an elastic-perfectly-plastic joint model was assumed, whereas the computed maximum factor of safety was considerably less when adopting an appropriate soil-infilled joint model.

Mar 8, 2011

The refractory industry in New Zealand is small, consisting of two main manufacturers - one at Huntly and the other at Kamo. Together these would have an annual refractory production of about 30 000 tonnes. The industries which use refractories include two steelworks, NewZealand Steel Limited and Pacific Steel Limited, the former is involved in continuous casting from sponge, iron and scrap steel and the latter is involved in ingot teaming from scrap steel and steel billets; One aluminium smelter, cement works, dairy companies, small foundries producing engineering requirements and many other small users. The New Zealand manufacturers produce refractories in thefire brick range, that is up to 50 per cent alumina content (ignited basis), based on indigenous raw materials and in the high alumina range up to 85 per cent alumina content (ignited basis) based on imported bauxites. All of the basic refractories high purity silica and high alumina low alkali refractories and many of the higher grade acid resisting refractories are imported.

Jan 1, 1976

By W Taylor, S Chen, R Haywood, M White, R West, J Ranasinghe

In March 2012 a combined BHP Billiton and Hatch team embarked on a program to improve the concentrate burner efficiency of BHP Billiton’s Olympic Dam copper flash smelting furnace. A multi-faceted approach including an analysis of the furnace using operational knowledge and first principles engineering led to the design and supply of a new central-lance (disperser). A new, patented, swirl method of introducing the copper concentrate into the furnace was developed to integrate with the existing concentrate burner. Plant trials in 2014 demonstrated an increase of nearly 10 percent in the oxygen efficiency of the furnace. The improved efficiency is expected to provide savings in operating costs and asset life extension of downstream gas and dust handling equipment.CITATION:White, M, Haywood, R, Taylor, W, Chen, S, Ranasinghe, J and West, R, 2015. Improved copper flash smelting at Olympic Dam, in Proceedings MetPlant 2015, pp 382–395 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By M Yahyaei, M S. Powell

Mineral processing plants have become large and complex, generally through progressive expansions. Addition of a pre-crushing stage to conventional Semi-Autogenous-Grinding (SAG) and ball mill - crushing (SABC) circuits has introduced a complex materials handling system coping with +200 mm particles. Application of High Pressure Grinding Rolls (HPGRs) and implementing hybrid comminution circuits (ie, HPGR-SAG mill) requires proactive control of the feed size distribution to each unit. Application of Vertical Tower Mills (VTMs) and other fine grinding equipment to achieve a finer grind size, while maintaining the throughput, requires splitting the feed evenly between parallel units. Many of the conventional comminution circuits (ie, staged crushing and screening followed by staged ball milling) must deal with the transition from open pit ore, which is generally altered and soft, to underground ore, which is intact and hard, requiring existing crushers to produce a finer product to unload the ball mills.This paper presents common process improvement opportunities which have been identified during a number plant process reviews conducted by the authors in Australian and international operations. The operation of comminution circuits to known and accepted standards, which is explained in this paper, could improve the performance of circuits by between 5 and 10 per cent, generally at no capital cost and often at a lower operating cost. The performance improvement can be realised as throughput increase, a finer product size, or reduced operating costs (ie, energy saving, low maintenance, less consumables).Process optimisation opportunities presented in this paper include: enhancing materials handling and storage to avoid segregation; standard operation of screens to reduce misplaced materials; proper feeding arrangement and control of crushers to increase their utilisation; preparing proper feed for SAG mills to reduce grind size; splitting the feed evenly between parallel equipment to improve utilisation, and controlling operation of classification units to improve energy utilisation.CITATION:Yahyaei, M and Powell, M S, 2018. Production improvement opportunities in comminution circuits, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 233–248 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By J Johansson, J Lööw

There are many reports about how the new technology will affect our work, sometimes they are utopian but often dystopian. Most of the visions describe the industrial work, while the work of the managers does not seem to be affected. In this article, the authors will discuss how the new technology within the concept of Mining 4.0 changes the conditions for leadership and the work of managers in a modern mining industry.

Sep 1, 2024

By Noble AC

Ore reserve reporting practices in the United States may be broken into four general categories as follows: ò Reserve reports, often of an unofficial and preliminary nature, which are made through the news media. These are often based on exploratory drilling or sampling results. ò Reserve reports made for the purpose of raising public funds by issuing securities on the stock market, or as part of other filings to the United States Securities and Exchange Commission. ò Reserve reports to obtain private funds from banks, financial institutions, or other investors. ò Reserve reports for internal use and planning by companies operating or evaluating mineral properties. This paper discusses current practices for each of these types of ore reserves reports and reviews recent changes which have affected those practices.

Jan 1, 1987

By T Roberts, D Faulkner, G Watt

Traditional mechanised resin rock bolting in hard rock underground mines requires the installation of resin capsules into a pre-drilled hole prior to the rock bolt being spun into a hole to mix the resin and set the bolt in place. In poor rockmass conditions, especially at depth or in highly altered faults and shears, the condition of the holes often deteriorates as the poor ground around it unravels and falls into the hole. This results in partially or fully blocked holes that either damages the resin capsule when they are being inserted into the holes or prevent it entirely until the hole is continuously cleaned of debris. This deterioration of the hole condition, and continuous need to clean and re-drill holes, also increases the diameter of the hole which in turn affects the continuously mechanically coupled anchorage mechanism of the rock bolt to the rockmass as there is simply not enough resin in the hole to fill the annulus between the bolt and the rock. This results in a large increase to critical heading cycle time and, more importantly, results in the rock reinforcement not performing as per design specification and increases the risk of instability. To overcome the quality control issues with resin bolt installation in poor ground, a single pass drill, install, inject and tension self-drilling resin bolt application was designed and implemented for use in such conditions. This system allows the operator to inject a two part polyester resin through a self-drilled hollow bolt to mix and fully encapsulate the rock reinforcement. The self-drilling bolt allows for post injection of the hole after the bolt has been installed into the rock and gives the operator manual or automated control on the amount of resin used in the hole to ensure complete encapsulation and continuously mechanically coupled anchorage to the rock. This allows the reinforcement to work as designed and provide the Geotechnical Engineer extra quality control confidence in these conditions. The implementation of this single pass resin bolting system resulted in significant decreases to the resin bolting cycle time and rock bolt quality control failures. In this paper the design, implementation and embedment into the development cycle will be discussed and the in situ quality control checks used to validate the increase in rock bolt installation quality will be shared. CITATION:Watt, G, Roberts, T and Faulkner, D, 2018. Single pass drill, install and inject self-drilling resin bolt application in poor ground, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 323–343 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By A J. Morrison, M Yahyaei, J S. Siong, J Wang, K Runge

The flotation cells used to upgrade ultrafine metallurgical coal (-250 µm) are usually poorly controlled leading to unnecessary loss of combustibles from the flotation system. This is mainly because coal flotation cells are typically controlled for process stability rather than optimisation of flotation performance. This is especially true for a flotation device commonly used in coal applications in Australia – the Jameson Cell. This then provides an opportunity to improve the flotation performance by shifting from a stabilising control strategy to a proactive optimising control strategy. For an optimising control strategy, the control system will require a means of relating and then measuring in real-time, the effect of changing operating conditions on the coal flotation performance. Hence, the major aim of this work is to propose a possible model-informed process control strategy that could be used for real-time performance optimisation. In this study, industrial site work was conducted on an industrial-scaled Jameson Cell at a Coal Handling and Preparation Plant (CHPP) in Central Queensland, Australia where superficial gas velocity was controlled to six different levels. At the same time, other process variables such as froth depth and flotation feed properties were measured. The empirical models developed from this study suggested that combustible recovery is a function of superficial gas velocity, froth depth, feed solid content and feed ash content and that a peak in combustible recovery existed as a function of superficial gas velocity. This led to the development of a model-informed control strategy that aimed to maximise the combustible recovery by determining and then operating the cell at the superficial gas velocity at which the peak occurs. This peak superficial gas velocity was found to be only a function of feed solid content. Based on these findings it would seem possible to operate a Jameson cell at peak performance by online measurement of feed solid content, prediction of the optimum superficial gas velocity and stabilising control to maintain operation at that superficial gas velocity set point. The development of this modelinformed control strategy can serve as a basis for the development of a more sophisticated modelpredictive control (MPC) system. However, more work will need to be done to improve the predictivity of the combustible recovery model by measuring and modelling performance over a wider range of operating conditions.

Aug 24, 2022

By J Heyes, R Getty, M Sanapala

Closure is an inevitable part of the life cycle of every mine. Successful closure outcomes critically depend upon early and ongoing integration of closure planning and mine planning. Early and holistic integration minimises residual risk and maximises opportunity to leave a cost-effective, positive legacy for the company, investors and future land users. Both disciplines are inherently interconnected and aim to maximise ‘value’ via trade-offs. Historically, integration of closure into mine plans has been poorly implemented across the industry. There is still a perception that closure planning only starts as the end of a mine life approaches. This inevitably leads to tension when making business decisions, with progressive closure often being deferred due to short-term drivers and incentives. To create a positive legacy after production has ceased, this tension can be managed by transparently and fully informing business decision-makers, such that the impacts of short-term decisions on long-term closure objectives are understood. BHP recently updated a business-wide standard ‘Our Requirements for Closure and Legacy Management’ designed to strengthen collaboration, education and integration of closure across the entire life cycle of the asset. Concurrently, the ‘Life of Asset’ definition was refined to include the postproduction phase, until closure objectives have been met. This paper discusses the criticality of mine planning integration with closure and how updates to Our Requirements sharpen the focus from transactional to transformational planning. These concepts are applicable to any mining operation aiming to achieve successful closure across the full asset life cycle, from exploration to post-production.

Sep 18, 2023

By Sun Y. L, Jiang J. J, Lu S. L

A distinguishing feature of tunnels in squeezing rocks is that a large deformation of the surrounding rocks takes place slowly and gradually, often called squeezing phenomenon. It is different from the rocksbursting phenomenon during which the deformation of tunnels occurs instantaneously when the resulting stresses exceed the strength of the surrounding rocks. The squeezing phenomenon has received great attention in the field of rock mechanics and tunnelling recently. The mechanism and various factors related to the large deformation and failure of tunnels in squeezing rocks are discussed in this paper on the basis of field investigations and laboratory model tests. The relationship between the deformation of surrounding rocks and support of the tunnels in squeezing rocks is presented in the form of numerical modelling.

Jan 1, 1995

By A Dal-Corobbo, R Zick

The coal mining industry is now faced with new regulatory requirements that limit the discharge of chlorides into receiving streams. To meet these new regulatory standards for treated mine water, a zero liquid waste approach was developed using advanced treatment technologies. The approach described in this paper will generate clean water for reuse in various energy endeavours or discharge to the environment, with no substantial liquid or solid waste from the treatment process leaving the site.CITATION:Dal-Corobbo, A and Zick, R, 2013. Zero liquid discharge in coal mining operations, in Proceedings Water in Mining 2013 , pp 221-226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By Yagi Y

The double track railway tunnel, called the Second Shirasaka Tunnel is being constructed under the supervision of Japanese PTational Rail- ways (JNR) in the tertiary soft rock strata in order to speed up the railway transportation. This tunnel (L=1765m), located in a central part of Japan, is excavated by the machine (roadheader), while the adjoining First Shirasaka Tunnel (L=1296m), completed five years ago, was driven by the blasting, and NATM is adopted in both tunnels. The geological features in this region are Neogene Tertiary of Miocene sediments consisted of mudstone, the sandy mudstone and the alter- ation of these rocks, having a squeezing be- haviour. And the geological structure is as complicated as some anticline and syncline structures, large or small scale exist, and as a lot of faults are found. The machine excavation manner using road- header is adopted in this tunnel to minimize the effect of excavation because there is a possibility of the occurrence of landslide due to the tunnel excavation, and also because local inhabitants reside on the ground surface.

Jan 1, 1987

By J F. Costa, A Grigorieff

Coal mining reclamation is a worldwide concern. This paper presents a Brazilian example where the economic aspects of reclamation are considered. The basic goal of the study is to transform the reclamation procedures into an economic process by integrating the use of land after reclamation and developing profitable post operations. Some of the activities considered in this case study include: using of the coal pit as a landfill, considering appropriate landfill design and construction; using the area for forest development; and developing grassland, forests of native species and the construction of ponds for fishery. This study will conclude that the mined area is: capable of storing large quantities of waste at a competitive cost and at a low environmental risk; commercial forest development is economically feasible; and the lakes and other reclaimed areas can be integrated into the landscape creating a fresh water supply and an area to raise cattle.

Jan 1, 2005

The art of flotation may be divided into two distinct branches, namely:-1. Collective flotation.2. Selective flotation.(1) Collective flotation is applied when all the valuable minerals in an ore are required in one concentrate, leaving ,only gangue minerals in the tailing. The method is applicable, for instance, to such ores as auriferous copper sulphides associated with gangue minerals only, or to silver lead ores low enough in zinc and other valuable minerals.(2) Selective flotation is applied when there are present in an ore two or more valuable sulphides, which cannot be subsequently efficiently treated unless they are separated from one another as well as from the gangue. For example, a silver-Iead-zinc ore, or a copper-gold-iron ore; where the iron is not required with the copper gold concentrate.In order to make these operations practicable chemical reagents have been developed, having power to exert definite actions on the various minerals when brought into contact with them in a water pulp.COLLECTIVE FLOTATION.In order to bring about collective flotation it is generally necessary to add to the pulp a frothing agent and an activator or activators for all the minerals which it is desired to float.SELECTIVE FLOTATION.The object of selective flotation is to activate the mineral which is to be floated, and at the same time to prevent all other minerals from floating.

Jan 1, 1936

IN 1906, soon after his arrival in New Zealand, a brief article was prepared by the writer on "The Salient Features of the Economic Geology of New Zealand," for the Journal of Economic Geology. In November, 1907, a somewhat similar paper, entitled "The Mineral Wealth of New Zealand," was read at the Royal Colonial Institute in London. The present contribution to the Transactions...

Jan 1, 1909

Degussa's PAL-system (peroxide assisted leach) has been proven to be more economical than the conventional cyanidation technique. Significant in- creases in the gold recovery have been reported, accompanied by savings in cyanide. Accelerated extraction kinetics and modified reagent demands necessitate a redesign of the conventional cyanidation plant. The South African Osprey Mine is presented as an example of a successful PAL-application. Based on the plant and laboratory data it is shown that the redesign of the flowsheet can be an important factor for the effectiveness of a metallurgical plant. In the case of the Osprey Mine, the PAL-technology all ows a modification of the current preoxidation-ClPcircuit to two separate CIL-plants to treat run-of-mine ore and old tailings dumps. A doubling of the throughput is possible without enlargement of the plant. This innovation in the field of gold extraction, the combination of the PAL-process with a redesign of the metallurgical plant, can be considered as a basis for a more profitable gold mine.

Jan 1, 1991

The Sto Tomas II orebody of Philex Mining Corporation is a porphyry copper deposit located at Padcal, Tuba, Benguet, Philippines. It was mined through open pit method for the first two years starting 1958 and subsequently through underground method using the Block Cave System. The slusher type of draw was employed at the upper levels of the orebody from mid-year of 1959 up to 1994 and then shifted to LHD as the ore became more competent at the lower levels. Application of rock mechanics played a vital role during the conceptualisation of the LHD method of draw, the first of its kind in the Philippines. Rock mechanics is a combined responsibility of the geology and the mine engineering staffs, with the geology providing the vital information to the mine engineering to include in the mine planning the following:the general geology of the orebody; the ground characterisation through rockmass classification; determination of the cavability of the ore column (this includes our experience on airblasts which occurred during the early stage of our last slusher blocks); undercutting sequence; fragmentation of the rockmass in the ore column; drawzone spacing; proper draw control procedure; lay-out of openings; and the design of ground supports based on the rockmass condition. For the proper interpretation of the rockmass that would cater to the diverse mining situations, Philex adopted the modified geomechanics rockmass classification (Mining Rockmass Rating, MRMR) as this system is recognised and used by most of the block cave mine worldwide. This paper aims to discuss and present the role of rock mechanics in the analysis and determination of geomechanical issues encountered in Philex mechanised block cave operation.

Jan 1, 2000

By K Akiro

Volcanogenic massive basemetal sulphide and gold mineralisation of predominantly low sulphidation style has been located within Lower Tertiary basaltic and felsic volcanic and sedimentary sequences at Ufuo, in the Left April River area, northwest Papua New Guinea. The four discrete massive sulphide bodies, which have been so far identified, occur within a 3 +5 km area situated within a north west trending structural corridor. The sulphide bodies are all localised on the margins of the corridor where the bounding major through going faults are transected by regional faults. Mineralisation is characterised by massive pyrite-bornite-sphalerite-barite-quartz-anhydrite deposition with later galena-tennantite-chalcopyrite. Minor phases include enargite, goldfieldite and bismuth sulfosalts. Jasperoidal silica lenses and bioturbated sediments are closely associated with the massive sulphides. Basemetal sulphide mineralisation is also closely associated with phyllic-style quartz-sericite- altered host rocks underlying the massive sulphide lenses. This mineralised phyllic alteration is localised to fractures, veins and breccias that cross-cut propylitic style alteration characterised by quartz, epidote, chlorite, adularia and zeolite. The mineralised system possesses several hydrothermal features consistent with a copper-rich submarine exhalative volcanic hosted massive sulphide (VHMS) system, ie discrete massive sulphide bodies with abundant barite, associated jasperoidal silica and bioturbated sediments. However, exploratory drilling of the alteration zone underlying each of the massive sulphide bodies has not identified a well-defined zoned alteration pipe that is characteristic of such systems. The alteration is also similar to that of a porphyry-related low sulphidation system in which phyllic alteration has overprinted a regional propylitic style assemblage. The presence of sporadic enargite (and ?tennantite/tetrahedrite) suggest there were intermittent pulses of acid fluids in the system probably derived from exsolved magmatic SO2 which flowed directly to the surface along reactivated faults. The occurrence of tellurium and bismuth minerals is also consistent with a magmatic contribution to the metalliferous hydrothermal fluids. It is proposed that the VHMS orebodies are the products of submarine exhalative deposition generated by a crystallising magma emplaced within crust of on-going tectonism. Ufuo mineralisation is similar to many VHMS deposits elsewhere in that it is unclear whether the metals are derived from the magma directly, or via seawater leaching of the wallrock. Additional studies such as oxygen isotope analysis may assist in resolving this issue. If the metals are shown to be of direct magmatic origin then there may be good prospects for discovering economic-grade porphyry-related mineralisation at depth below the massive sulphide deposits.

Jan 1, 1999