Search Documents

By Davey P. T, Tsambourakis G

Mineralogical analysis of supergene sulphide ore recovered from areas close to the underground workings at the abandoned Mutooroo (South Australia) mine shows that the original sulphide minerals have undergone substantial alteration. The cause of this alteration is believed to be contact with the highly saline, acidic mine water. The copper is now present as a sulphide that can best be described as a copper- and iron-delicient chalcopyrite, CuxFeyS2, where in most cases x < y. The values of x and y vary from point-to-point within each grain.Leach tests under a variety of conditions show that dissolution of the copper from the supergene sulphide ore can be readily achieved, particularly when compared with the behaviour of Mt Isa chalcopyrite concentrate. For the supergene sulphide ore, an increase in the acidity and the iron(lll) concentration of the leachant re ults in an increase in the rate of copper dissolution.The results are briefly discussed in terms of the experimental in-situ leaching operation at Mutooroo, South Australia.

Jan 1, 1986

By A Scott, S Kanchibotla, J Segui

The æMine to MillÆ concept is not new. In fact, it is the underlying objective of every mine. Unfortunately, in many operations the management structure and reporting systems have created independent æbusinessesÆ within the overall mining enterprise. This has created incentives to optimise the performance of each component of the operation rather than the enterprise as a whole. The Mine to Mill Conference organised by The AusIMM in October 1998 documented a number of case studies where run of mine ore was not presented to the mill in the best possible form for subsequent stages of comminution and processing. A number of examples were quoted where modest expenditure in the mine had a very significant impact on downstream process efficiency and hence costs. Examples included:the minimisation of fines in the mining and handling of iron ore; the management of fines in blasting and crushing for a copper heap leach operation; the control of blast damage, mining recovery and dilution in open cut coal operations; and the optimisation of mine fragmentation to increase mill throughput in gold and copper operations. The latter topic has been trialed at a number of mines and is referred to as æMine to MillÆ fragmentation. A number of æMine to MillÆ type investigations have been reported in the literature including Pease et al, Simkus and Dance, Nielsen, Scott et al, Kojovic et al, Kanchibotla et al, Bulow et al and Hawkes from the 1998 Mine to Mill Conference. In addition, a number of studies are in progress or the results have yet to be published. These studies have demonstrated the feasibility of obtaining the data required to characterise the breakage behaviour of ores and to model the impact of changes to blasting practices on process efficiency. Characterising the breakage behaviour of ores is a vital step in the management of fragmentation and comminution in mines. The characteristics of importance to fragmentation fall outside the parameters conventionally required to describe the economic geology of a deposit. æMine to MillÆ optimisation of fragmentation means that the mining engineer needs information from the geologist in order to be able to help the metallurgist. Providing this information requires close interaction between these groups.

Jan 1, 2000

The paper presents the development of an integrated computer aided design and planning of open cast mining, with the use of object-oriented modelling and geoinformation technologies, on the example of interaction of the subsystems on planning optimisation and freight traffics.

Dec 6, 2010

With the advent of the resources boom in the late 1960s most of the larger scale resources projects in Australasia were commissioned on an æowner miningÆ basis, where the mine owners owned and operated the primary mining equipment. Then, in the 1980s with the arrival of the gold mining boom in Western Australia and elsewhere, a change occurred û most of the mining activities were carried out on a contract mining basis. Over recent years, however, there has been a marked trend amongst larger Australasian open pit mining operations back towards owner-controlled and operated mining operations. The reasons for this are many and are addressed in the paper, but centre on the concept of the owner being prepared to assume more of the mining risk in exchange for the advantage of not having to pay a contractorÆs profit margin. Where mining contracts are entered into, the older æschedule of ratesÆ format is being replaced with less adversarial and more entrepreneurial contract alternatives involving operating cost and risk sharing in a spirit of æfair dealingÆ. Leasing and maintenance issues have also been influenced in recent years by the advent of more flexible contract arrangements with equipment suppliers. Group purchasing has also had some influence for project operators. For many mine owners, the optimal risk management profile involves a practical offsetting of the assumption of mining risk on the one hand, against the removal of litigation risk and potentially reduced operating costs on the other. Potential pitfalls may arise where equipment size and type requirements vary with time or where manpower management, mining flexibility, job skills or safety exposure factors are relevant. These issues are commented on in the context of some well known examples, and an update is provided on contract mining versus owner operation in large scale Australasian open pit mining generally.

Jan 1, 2002

By V Chamberlain, M Appeah Owusu, M Aniawu-Asumakah, A Anyimadu, R Peattie

This is an integrated geology and plant improvement study arising from the heterogeneity seen in mineralogy and gold association at the Obuasi goldmine in Ghana. This heterogeneity comes from the two ore types mined, the one being a sulphide ore, mainly composed of gold-bearing arsenopyrites. This gold is refractory and exhibits a strong relationship between gold and As. The other is quartz veins, that are high grade and free milling. The installed circuit consists of comminution – Gravity -Flotation – BIOX – Leaching and Adsorption processes. The opportunity tested involved improved mass pull - related flotation recovery of Au in the Sulphide stream; while balancing the need for a minimum Sulphide grade for the Bio-oxidation process, occasioned by the removal of 25 to 30 % of the (quartz) stream through preconcentration by Ore sorting. The current circuit is then utilized for the sulphide route, while a smaller grind-gravity circuit is utilised for the quartz stream in a relatively inexpensive way, followed by a common leaching and adsorption circuit. Added advantages of the strategy includes faster recovery of gold from the quartz stream, with less consumption of reagents from saving on flotation and BIOX reagents for this stream. Screening and Ore sorting was successfully tested with laser technology, achieving over 98% separation of quarts (containing up to 40% of the gold). The plant schedule of Ore, the suggested circuit design for the Ore sorting, the results obtained from the different flotation regimes, as well as consequent financial modelling have been presented and discussed in this paper. This illustrates the opportunity that arises out of a detailed analysis of material versus installed circuits, even if the gains in pre-concentration do not necessarily involve rejection of gangue material. An added opportunity for future investigation, briefly discussed but not tested in this paper, would be to maintain current mass pulls but with increase in throughput (by the space created by the sorted material). This will of course require the mining ability. It could also add LOM value by altering the cut-off grade.

Nov 10, 2020

I report results of over 850 microprobe analyses of sulfides, sulfosalts and electrum from the Favona adularia-sericite epithermal deposit of the Waihi district in the southern Hauraki Goldfield of New Zealand. Pyrite and marcasite from altered wall rocks that enclose the veins are stoichiometric, with compositions of FeS2, and no significant trace elements. In contrast, pyrite in veins commonly contains appreciable As (up to 3.2 wt per cent), and locally contains several tenths of a percent of Cu, Zn, Co, Ag and Sb. Vein pyrite may contain up to 0.22 per cent Au, but Au contents do not show a positive correlation with As. Limited electrum data indicate that it ranges from Ag0.47 Au0.53 to Ag0.54Au0.41Cu0.01Zn0.04. Chalcopyrite is stoichiometric CuFeS2, and most galena is PbS, but some galena contains up to 4.4 wt per cent Se, which substitutes for S in its lattice. The galena is not argentiferous; the highest Ag content is 0.45 wt per cent Ag. Sphalerite averages 4 mol per cent FeS, but ranges up to 15 mol per cent. Tetrahedrites [(Cu,Ag)10(Zn,Fe)2(As,Sb)4S13] show variable substitution, but most are Cu- Zn- and Sb-rich. Veins also contain aguilarite (Ag4SeS), stromeyerite (CuAgS), naumannite (Ag2Se), and mckinstryite [(Ag,Cu)2S].

Jan 1, 2004

Nickel laterite HPAL circuits are known for their complexity and have presented a large number of challenges to process engineers worldwide. An attitude commonly encountered by the author is that the beneficiation of the ore is relatively simple and that the difficult problems are in the realms of hydrometallurgy. On a number of occasions beneficiation has become the 'poor cousin' in the process design phase. Another common theme is that significant difficulties are encountered when beneficiation circuits are started up, invariably slowing the ramp-up of the remainder of the circuit. In some cases the problems impact on throughput for a long period and can require major rectification capital. The HPAL Ni laterite projects encountered each have their own set of beneficiation problems that need to be understood before an appropriate circuit can be designed. This paper will discuss a range of design issues including geometallurgy, ore characterisation through laboratory testing, the application of appropriate sizing and analytical procedures, the selection of appropriate unit operations, materials handling of plant feed and products and setting meaningful plant design requirements.

Jan 1, 2008

By M Salu

Ventilation control devices (VCD’s) and bulkheads are critical controls used for managing risk in underground coalmines. Following the Moura No. 2 mine explosion in 1994, the Queensland Mines Department required that the design of VCDs be based on live testing (such as in a mine testing explosion gallery) and more recently on numerical modelling using measured seal material properties. While the stipulated methods represent an idealistic solution, they are not practical to implement as solutions to daily challenges presented in underground coalmines.Not all VCD’s and bulkheads are placed in areas which have been mined to standard roadway dimensions. Operationally, VCD’s may be required to be placed close to intersections or require large dimensionally different areas (eg overcasts and pre-driven recovery road shutters) compared to the live testing or numerical modelling originally undertaken.This paper describes the various structural engineering methods utilised to account for the design of VCD’s where the operational requirements are non-standard. Siting and construction of VCD’s near the entry of cut throughs and geological structures requires additional design considerations. While VCDs constructed from a single material (eg sprayed mining plaster) are relatively straightforward to design, the addition of multiple openings (doors) or large pipes will complicate the structuralanalysis significantly.Temporary bulkheads used for the containment of grout such as for the construction of pre-driven recovery roads in coal mining have a significantly different risk profile to VCDs and should be designed accordingly. Recent failures and near-misses in such bulkheads have highlighted this issuefor the authors.The existence of an Australian Standard for Underground Mine VCDs and Bulkheads would go a long way to addressing many of the issues raised in this paper. Without a single, industry-accepted reference for VCD design, individual mines will have to continueto exercise their best judgements using whatever local expertise is available to them.

Oct 12, 2022

By S Arai

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Podiform chromitites are commonly found in the Moho transition zone to the mantle section of ophiolites, but have been very rarely found from the current ocean floor, even though some ophiolites are considered as a slice of oceanic lithosphere. One of the factors controlling podiform chromitite formation is the chemistry of host mantle peridotite; an intermediately refractory harzburgite is the optimum host for chromitites. This harzburgite represents the most common lithology of the oceanic lithosphere, where the peridotite-melt reaction, which is another condition, is possibly common there. The oceanic lithosphere mantle is thus a good host for podiform chromitites. The apparent rarity of documented oceanic chromitites is solely due to under-sampling of mantle materials from the fast-spreading ridge and the segment centre of slow-spreading ridges. Some ophiolitic chromitites formed not from genuine mid-ocean-ridge basalt (MORB) but from wet MORB due to the situation of typical ophiolites, which formed not at ordinary mid-ocean ridges but at supra-subduction zone spreading centres.CITATION:Arai, S, 2015. Podiform chromitites do form beneath mid-ocean ridges , in Proceedings PACRIM 2015 Congress, pp 465–468 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By R J. Mills, B S. Sinclair, D A. Fergusson, A G. Goldstone

In 2005, Solid Energy New Zealand Limited obtained non-notified consent for the disposal of 1Mt of coal ash at the Rotowaro minesite, forming part of a coal supply agreement with the Huntly Power Station. The consenting of major mine site activities has historically required wide consultation and involves notification of the application.   The risk and cost associated with consultation can be significantly reduced via a non-notified process. A non-notified consenting process necessitates environmental effects to be shown to be æless than minorÆ, which requires the combination of robust science and a pragmatic approach to design, assessment of environmental effects, and consenting issues.   Key issues examined included consideration of how to practically operate a significant disposal project within the confines of an operating mine, minimising the costs, civil and geotechnical design and practical issues associated with traditional disposal. Environmental issues specifically related to the coal ash, led to a site specific performance driven approach to management rather than relying on conventional prescriptive approaches. Environmental issues of concern include the leaching of boron and aluminium from ash into groundwater and mine water management systems where both boron and aluminium can occur at elevated levels.   Coal ash exhibits unusual geochemical characteristics reflecting the primary coal composition and the combustion process. The dominant coal type combusted at the Huntly Power Station is derived from Rotowaro and the resulting ash is cementitious and has a high alkalinity. As a result the disposal design is based on the characteristics of the ash itself rather than the material into, or onto which the ash is disposed. Non-notified status was able to be achieved through consideration of these key characteristics of the ash, ensuring that the dimensions of the disposal site and each location was designed to minimise the flow of groundwater through the ash and demonstrating that the physical ash disposal effects are less than minor compared to the consented mining operation.

Jan 1, 2006

Sample preparation for gold samples, where the distribution and size of gold particles is often irregular, usually demands that a relatively large sample weight is taken to produce a representative sample for analysis. Traditional sample preparation of gold samples incorporated multiple stages of coarse particle size reduction followed by subdivision of the sample prior to final fine pulverising. This technique developed because of the limited equipment options available to laboratories. As a result significant errors are introduced and the final sample size being pulverised is a small fraction of the original sample weight. Three significant developments have occurred in the last 25 years to significantly improve sample preparation of gold samples: 1.  large capacity fine pulverising,2.  fine jaw crushing, and3.  whole sample coarse pulverising. In the mid-1980s an Australian manufacturer developed large capacity pulverising bowls which had the ability to reduce samples with a mass of 1.5 - 3.5 kg to a nominal 0.075 mm product in approximately three to five minutes. Laboratories were able to produce a large homogeneous pulverised sample which significantly reduced the error in sampling. However, exploration and mine samples are usually 7 to 10 kg and the sample requires a subdivision stage following crushing to produce the 3.5 kg for the pulverising step, thus introducing potential for significant error. The development of fine jaw crushing allowed particle size reduction to -2 mm which reduced the subdivision error of the bulk sample prior to fine pulverising. Subdivision of the crushed sample at -2 mm still results in potential sampling errors, where the gold particles are not sufficiently liberated to be representatively sampled. Clearly the best option would be to reduce the particle size small enough to ensure a representative sample prior to final pulverising. Continuous mills offer a partial solution but are relatively slow and subject the sample to differential pulverising prior to subdivision. Clearly this does not provide the best solution for routine laboratory applications where high volumes of samples are to be processed. The recent development of a large capacity coarse pulverising system allows samples of up to 10 kg to be reduced to -0.25 mm prior to subdivision, and fine pulverised to -0.075 mm. Laboratories now have the necessary equipment to perform reliable large capacity sample preparation of gold samples. The exact choice of a sample preparation scheme may still depend on particular ore types but the need for multiple crushing and subdivision stages is redundant.

Jan 1, 2008

By C D. McCullough, M Gerner

Rarely do opportunities arise allowing closure of a mine site to be planned as a key beneficial land use asset within a new urban growth area; particularly so well prior to cessation of mining.Pit lakes are common mine closure legacies for many open cut mines and may form in open cut mine voids extending below the water table upon closure. Mine closure guidelines increasingly require post-mining land uses of equivalent capacity to premining conditions and that minimise long-term post-mining liabilities and maximise benefits to stakeholders and the environment. However, risks presented by pit lakes are regularly neglected in closure planning or are not able to be addressed to allow beneficial end use of the lake or surrounding land.This paper describes strategic planning initiated by quarry owners ten years before mining ceases. In liaison with the planning agencies, the planned closure of a large 100-year-old limestone quarry pit will form a lake on mine completion, with a well-considered beneficial end use in an urban setting in mind. The quarry pit and adjoining land at Batesford South about the edge of the City of Greater Geelong, Victoria, Australia. Geelong is experiencing growth pressures that necessitate development of a new growth area from about 2025.A multidisciplinary expert team assessed the constraints, opportunities and feasibility of rehabilitating the quarry and pit lake and developing the surrounding land as Geelong’s next urban growth area.The concept is exciting and demonstrates that a former mine site could become a valued home to about 40 000–45 000 people. About 30 per cent of the land will also be developed as an ecological riverine corridor including the pit lake that will become a regionally iconic lake as the centrepiece of an urban development.Our paper outlines technical challenges and how these can be met to achieve closure and beneficial use that meets the social, economic and environmental expectations of contemporary urban planning.CITATION:Gerner, M and McCullough, C?D, 2014. Planning for the future – development of beneficial end use from a quarry pit lake, Victoria, Australia, in Proceedings Life-of-Mine 2014 , pp 99–112 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

Improving the Sustainability of Primary Metal Production - The Need for a Life Cycle Approach

Sep 13, 2010

By Bailey H. W

Power supply for remote mining developments is compared with supply to the general public with the conclusion that the private power plant operator has many opportunities to minimise his costs which are not open to public utilities. The main features of diesel, gas turbine and steam power plant and the limitation upon their application which may be imposed by the fuels available and the local conditions at remote sites are outlined. Reference is made to the value of joint examination by the mining engineer, metallurgist and power engineer to decide how to make best overall use of capital, labour and energy in co-ordinating the design of power and process plant and in setting no more than adequate standards of reliability and efficiency. Fluctuations in world markets make it difficult to plan mining operations to a firm time base. Suggestions are made to minimise the financial risk in forward expenditure upon power plant which in large sizes due to longer construction time may have to be ordered before a final decision is taken upon the mining development it is to serve.

Jan 1, 1973

By Hindmarsh G

The colliery is owned by the BHP Collieries Proprietary Ltd., the principal shareholders being the Broken Hill Pty. Company Ltd. and Hebburn Limited.It is situated due west of Newcastle and 6 south-east of Cessnock, N.S.W., and is conneeted by 36 miles of railway to the port of Neweastle. Of this mileage, 3 miles are owned by the Company, 3 by Hebburn Limited, 9 by the South Maitland Railways Ltd., and 21miles by the Government Railways.The seam worked is known as the Main Greta Seam of the Greta Coal Measures and is on the southern slope of the Lochinvar anticline.At the shaft, the seam is 1190 ft. below the surface, and the section of the coal measures is:-Upper or Main Seam, . 24 ft. 0 in.Conglomerate and shale 70 ft. 0 in.'Middle Seam 8 in.Conglomerate 25 ft. 0 in,Bottom Seam 1 ft. 2 in.These lie between two marine measures, and are the lower coal series of the permo-carboniferous period.Only the upper seam is workable in this area, the lower seams being too thin for eompetitive working. The section of the workable seam at the shafts is as shown on Fig. 1.Unfortunately, only the lower 12 ft. 5 in. of the seam is saleable.

Jan 1, 1935

By J Addai-Mensah, M Adam, W Skinner, J Begelhole, K Quast

Granulation of iron ore fines into robust granules is critical to successful sintering and blast furnace operations in iron and steelmaking. Iron and steelmakers desire iron ore granules with high strength, uniform size distribution and low fuel consumption to enhance efficient sintering operation. Unlike hematite ore, magnetite concentrates do not granulate easily at low binder dosage to yield coarser granules due to the absence of nucleus particles. This motivates the present study to harness the complementary properties of hematite ore to enhance granulation of magnetite concentrates via blending. The current state-of-the-art in hematite and magnetite blend granulation is reviewed, along with granule property limitations. Preliminary experimental work on granulation of hematite and magnetite blends as a precursor to sintering is reported.CITATION:Adam, M, Addai-Mensah, J, Begelhole, J, Quast, K and Skinner, W, 2017. Enhancing magnetite concentrate granulation by blending with hematite ore, in Proceedings Iron Ore 2017, pp 17–24 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Real-Time Integration of Mining and Metallurgical Information for Efficient Use of Energy and Water

Sep 13, 2010

An understanding of the origin of mineral deposits and their relationship to local and global geotectonics is essential if regional targets for mineral exploration are to be chosen. Volcanism, metamorphism and tectonism are especially significant for the origin and emplacement of mineral deposits, which, far from being fortuitous oddities of nature, occupy well defined positions within distinctive lithofacies. Thus, suggestions for mineral exploration targets can be made taking into consideration the position of 'fossil' convergent and divergent plate tectonic boundaries to indicate areas of specific types of mineralisation. To be borne in mind, though, that level of exposure, time and location of magma generation are all additional and important controlling factors. To further understand the importance of the above parameters, one must refer to the concept of paired metamorphic belts (Miyashiro 1973) which develop during an orognic cycle. These belts are generally constructed in such a way that an ophiolite type complex with metamorphic grades related to high pressure and moderate temperature regimes is flanked by an area of calc-alkaline volcanism and granitic activity with metamorphic grades within a region of high temperature and low pressure. The former situation is usually the seat of primary magmatic mineralisation, whereas the latter contains base metal. Deposits of acid plutonic and volcanic association. As will be seen later, this particular metamorphic-volcano-orogenic situation is well developed in some parts of New Zealand. For the present purpose a distribution of potential ores as related to plate tectonic processes is given below:a) Divergent plate boundaries: primary magmatic Ni-Cu, Pt,Cr, PeS2 and Cu, Pb,Zn in hot brines-hydrothermal environments Mn deposits.b) Convergent plate boundaries: stratabound Cu-Fb-Zn-Ag of felsic volcanogenic association. Porphyry eu-Au of island arc type, porphyry Cu-Mo of continental type. Cu, Au, Y, Sn, Hg, Sb of vein type and replacement lode related to granitic activity.c) Au of hydrothermal vein association, related to late dynamo-metamorphic events. By virtue of ocean floor spreading, regions of divergent plate boundaries are eventually juxtaposed or welded n to areas where plate collisions occur. This is then followed by partial melting due to various causes, just above the descending plate; thus creating a zone of acid to intermediate magmatism. The final picture is that of an orogenic zone with the paired metamorphic belts outlined above.

Jan 1, 1976

Many sampling standards arrive at a value for the prescribed sample mass by assuming a specific relation between the sample mass and the relative standard deviation of the fundamental error and assigning a value to the tolerated coefficient of variation. In order to obtain an equation that provides a relation between the minimum sample mass and the particle properties, many different models for the drawing of a sample have been developed. Here, a model for the drawing of a sample is proposed which can be considered to be a generalisation of the model used in GyÆs sampling theory. Using simulations, it is illustrated that the generalised model can lead to a better correspondence with actual sampling processes.

Jan 1, 2005

By S Wilkinson, S Black, L van den Berg

"The mine ventilation system plays an important role in mitigating human exposure to diesel particulate emissions (DPM), exhaust gases and heat in underground mines. The mine’s secondary ventilation systems are critical for diluting contaminants when working at the face of a heading. To improve these systems it is important to understand and visualise the localised air flow profiles. We have considered an approach that includes both tracer gas measurement–modelling to analyse this complex flow behaviour in a heading. The use of tracer gas enables reliable measurements of flow behaviour and differentiation between the contributions of various contaminant sources including DPM. A pilot study was conducted to demonstrate how tracer gas can be used to directly measure the effectiveness of ventilation dilution in a heading during shotcrete activity. This activity is considered to be one of the more challenging areas for diesel exhaust exposure management. Exposure sources include the diesel engine of the spraying equipment (Spraymech) and concrete agitator truck (Agi) that supplies the shotcrete. During operation both the Spraymech and Agi operators are located outside the equipment’s air-conditioned cabins and both are exposed to diesel exhaust. In the pilot study tracer gas was injected directly into the Spraymech exhaust stream. This allowed thorough mixing, ensuring the tracer gas was able to track exhaust gases and particulates released to the heading. The release was repeated at three different headings with varying degrees of secondary ventilation controls. The study showed that small changes to the secondary ventilation system can significantly impact the contaminant concentration. It also demonstrated that tracer gas can be used to isolate different contaminant sources. The intent is to use this technique in a more comprehensive study to develop best practice guidelines for secondary ventilation installations. This paper presents the technique used and the preliminary results from the pilot study. CITATION: Wilkinson, S, van den Berg, L and Black, S, 2015. Application of tracer gas flow profiling to improve secondary ventilation practice – a pilot study, in Proceedings The Australian Mine Ventilation Conference, pp 345–352 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 31, 2015