Search Documents

By Rokot M

In a little over three years, Chevron Niugini has built up a team of relatively young, hard working men and women, mostly Papua New Guineans, who spend most of their working days out among people in the Southern Highlands and Gulf Provinces who are directly affected by the Kutubu Petroleum Development Project. These are Land and Community Relations officers, or LACROs. They take on a huge responsibility, not only representing Chevron but also being friend, advisor and negotiator, frequently dispensers of medicines, and agricultural advice and more. When things go well, others get the praise, when things go wrong, LACROs are the martyrs. Just as the geologists who locate the oil, the drillers who find it, the engineers who design the facilities, the construction gangs who build them, the landowners who claim it, and the Government who monitor it, so are the LACROs part of a team.

Jan 1, 1991

By S Maritsa, E K. Chiwandika, S M. Masuka

The iron and steel industry is experiencing an increase in the use of iron and steel commodities within societies, decarbonisation pressures, depletion of high iron ore grades and high energy consumption. This necessitates scrap metal recycling, low-grade ore utilisation using the induction or electric arc furnace to achieve the global target of net zero CO2 emission. The available highquality scrap metal cannot sustain the steel industry but the world has unused hematite-goethite ores. It is the aim of this research that this resource be utilised using the induction furnace to sustain the steel industry in an environmentally friendly manner. Indurated pellets prepared from the hematite-goethite ore, 5 wt per cent limestone and 5 wt per cent coal addition were smelted in the induction furnace at 1350 ± 50°C with 25 mins holding time. The effects of basicity and carbon content were also investigated to optimise the smelting parameters. The results showed that the careful control of the basicity, and iron-to-carbon ratio maximised total metal recovery. The optimal basicity ratio was determined to be 1.3 and a carbon to iron ratio of 1.4 achieved a total metal recovery of 73 per cent. The metal recovery was closely related to the estimated slag melting temperature. The basicity ratio of 1.3 achieved the lowest slag melting temperature estimated to be around 1380°C based on the CaO-SiO2-Al2O3 phase diagram. The recovered metal had a comparable chemical composition and microstructure to that products from an ITmk3 furnace.

Jun 19, 2024

By J A. Rowland

When executing a ventilation change the mine ventilation circuit is in a state of flux throughout the entire change period with discrete mine areas both under ventilated and/or over ventilated during the change process. Whilst routine risk reduction strategies such as removing electrical power and people from the mine are commonly deployed it is wise to complete the change in the shortest practical time frame. This not only minimises the chance of unacceptable concentrations of contaminants accumulating around the mine but reduces the impedance on production activities which are routinely suspended during these change periods. This paper firstly highlights the importance of the maintenance of an accurate ventilation model and discusses issues which should be considered to assist to maintain in it a suitable state of health. Further it provides some tips on how to monitor that your model is in an acceptable state of tune so that it can be confidently deployed in the change process. Finally, it details the sequential process how a finely tuned and accurate ventilation model can be utilised to carry out major ventilation changes according to appliance pressure adjustments only and without the need to constantly measure and check resultant branch flows throughout the whole change process. Also discussed are some simple practical tips which will help ensure that the ventilation change process will go according to the devised plan on the day and in the most appropriate order including checking the efficiency and accuracy of the change, after it is completed.

Oct 12, 2022

By R G. Moreby, S Bluhm, FávonáGlehn, C Pascoe

Resolution Copper Mine in Arizona, USA, is planned to be a 2000 m deep panel cave mine with virgin rock temperatures exceeding 80¦C in rock with high crystalline silica content, resulting in a very challenging ventilation and cooling system design. This is one of the largest copper orebodies ever found and, with a planned rock production rate of 120 kton/day. The project is currently in its prefeasibility phase and the paper discusses features of the ventilation and cooling system design which includes multiple ventilation shafts with total primary ventilation flow of about 3000 m3/s and both surface and underground refrigeration plants producing more than 140 MW refrigeration capacity. The cooling system features large surface bulk air coolers chilling all downcast air supplemented by an underground secondary air cooler system and a chilled service water system. This will be a very challenging mine to ventilate and cool but this work has demonstrated that it will be technically achievable with the application of existing technology.CITATION:Bluhm, S, Moreby, R G, von Glehn, F and Pascoe, C, 2013. Life-of-mine ventilation and refrigeration planning for Resolution Copper Mine, in Proceedings The Australian Mine Ventilation Conference , pp 125-138 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

Lihir Gold Mine is situated in a dormant volcanic caldera on a small island off PNG. Not æextinctÆ but dormant. Current ground temperatures are up to 150 degrees Celsius with active geysers in the workings of the mine, pools of boiling ground water adjacent to low-grade dumps and hydrogen sulphide gas emissions. It is a unique mining environment by world standards. This paper will deal with the following issues encountered and managed by the operation:blasting in hot and reactive ground; management of sulphide gas emissions; disposal at sea of all mining waste rock; one dear to all Australian minerÆs hearts û dealing with landowner groups; and unusual human resource issues.

Jan 1, 1999

By Tinto R

Aims of the Forum A contribution from Dr Robin Batterham, Vice President, RIO TINTO Research & Technology and a member of The AusIMM Standing Technology Advisory Qroup. Dr Robin Batterham is of view that the inevitability of automation in the minerals industry and the importance of addressing the human implications. He also outlined Rio Tinto's approach to automation. The progressive introduction of automation into mining operations will be revolutionary in its effects. This is the experience in other industries and it will be no different in mining. Mining companies most successful at implementing the new technologies will gain relative competitive advantage and those manufacturers who produce the most desirable automated equipment for miners will also gain market share.

Jan 1, 1997

By Mandzic E. H

The Dome Mine of Timmins Mining company is located in South Porcupine, N.W. Ontario. The orebody being mined partially lies in the No. 3 shaft pillar. Stability analysis has been carried out to establish the influence of nearby mining on ground movement in the shaft vicinity. Mathematical modelling of shaft displacement has been done for stope layout at depths from 180-210 m and distances of 10-50 m from the shaft. Analysis indicated that ground displacement around the shaft is below 1 mm/m and one third less for cut and fill than in the case of open stope mining. The result of the investigation was later confirmed by cut and fill mining of this orebody.

Jan 1, 1986

By S C. Barrie

St BarbaraÆs Marvel Loch operations have successfully used longhole open stoping as the primary mining method for a number of years. A transition to Core and Shell mining was implemented in 2009 to recover substantial ore grade resources remaining in sill and rib pillars. The transition to core and shell for the Exhibition lode required continuous waste filling of created voids and thus the removal of the crown pillar at the base of the Exhibition pit by blasting. Access to the top of pillar was denied as the pit was partially rock filled with waste rock from underground development.Beyond the technical challenges of the blasting project, a simple and transparent risk management process was developed to ensure appropriate controls and mitigating strategies were in place to minimise risk to personnel during the pillar removal process.Although failure of the crown pillar was anticipated but with the actual timing unknown, on 25 December 2011 the crown pillar yielded during normal mine operations. Engineered and isolation controls in place at the time were of a sufficiently high standard to ensure limited exposure of the underground workforce and minimal damage to mine infrastructure. Successful risk management through implementation of appropriate controls during the project lifecycle of two years and three months proved to be fundamental to the safe removal of the crown pillar.CITATION:Barrie, S C, 2012. Successful risk management through project life cycle for removal of the crown pillar at the Marvel Loch Underground Mine, in Proceedings International Mine Management 2012, pp 125-134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By E Beltran, S Ngunz, F Orrante, F van Zyl, M Westcott

"The primary control objective of the project is to achieve milling optimisation by ensuring that the energy available for rock breakage is used as efficiently as possible. This is achieved by increasing the level of mill filing until a process constraint is reached. Stable operation against this limiting constraint is then maintained to ensure long-term optimised operation.Semi-autogenous grinding (SAG) mill control optimisation presents a number of challenges. SAG mills have multiple inputs that are used to control multiple outputs (MIMO process). Secondly, the SAG mill loading process is a ‘high inertia’ process that can be approximated as an integrating process. This means that it is open-loop unstable. The hybrid control strategy presented implements an advanced ‘load stabiliser’, which transforms this integrator process into a more manageable first order process, which can be steered stably against the constraints. This SGS hybrid Expert control strategy implemented on both SAG mills at the Porgera concentrator therefore consists of two integrated parts responsible for:stabilising the mill load to a targetdriving the mill load target to the maximum determined by the process constraints (eg maximum power draw) to maximise efficiency and throughput. A comparative study is done between the operation of the plant for a period of a month before and a month after the implementation of this strategy. The results indicated a significant improvement in the SAG mills’ stability and operation as well as a reduction of overload situations leading to a loss of throughput.Citation:Ngunz, S, van Zyl, F, Orrante, F, Beltran, E, Westcott, M and Wilson, S, 2016. Simplified Hybrid Semi-autogenous Grinding Mill Control - Explanation and Practical Results at the Porgera Concentrator, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 313–320 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

Successful evaluation and exploitation of resources and reserves relies on the collection of high quality sample data. The quality of the sample data must be maintained through the application of a robust quality assurance and quality control (QAQC) program, including documentation of sampling procedures, training of sampling personnel and the regular monitoring of control samples. However, the application of QAQC programs in the minerals industry is often poor and the purpose misunderstood. It is all too common to have good quality control data collected, but no analysis work carried out until after drilling is completed. In a lengthy drill program, this can lead to problems not being discovered and corrected as they happen. Moreover, rectifying problems afterwards will be costly in terms of time and money, if not impossible. The consequences of poor quality sample data are many and include such effects as over- or underestimation of block grades, misclassification of ore and waste, and lower confidence in the resource/reserve models. The purpose of this paper is to highlight, using case studies, the importance of good QAQC practices to monitor the quality of sampling and laboratory sample preparation and analysis.

Mar 1, 2010

AustraliaÆs strong position as an aluminium producer and potential magnesium producer combined with rapid market growth in the automotive industry, proximity to Asia and other natural advantages points to considerable opportunity for downstream processing and manufacture with light metals in this country. Development of a vertically integrated light metals industry in Australia needs to be pursued with vigour, as does the continued development of global strategic alliances through the value adding chain.

Jan 1, 2000

The total cost of horizontal development can be minimised by optimising the cost of each of the component operations (eg drilling, blasting, etc). Component costs should not be minimised. To optimise blasting results (ie the mean advance per round, muckpile characteristics and overbreak), operators need to optimise the blast design and drilling and blasting procedures. The costs of pulling extremely long (say >6 m) rounds, producing unnecessarily fine fragmentation, and minimising overbreak are excessively high. Operators should continually consider how they can shorten the cycle period by saving time at the face. To enable it to be matched to the pertinent rock properties, the blast design needs to be based on as much relevant experience as possible. To develop the most valid correlation between blasting results and blast design, the latter must be implemented carefully and accurately, but without sacrificing speed excessively. The total cost can often be reduced by using: 1. computer-controlled jumbos (to reduce the period and cost of drilling and to increase drilling accuracy); 2. larger diameter (51 mm to 64 mm) and longer (4.5 m to 6 m) blastholes; 3. at least three large diameter ( ¦89 mm) relief holes that are 0.2 m to 0.3 m longer than the blastholes; 4. explosive products that are selected on the basis of proven reliability and overall cost efficiency rather than price; and5. stemming (to increase the amount of effective work done by each kilogram of explosive and, hence, to reduce the powder factor and possibly the number of blastholes and the costs of drilling and initiation). Non-perimeter blastholes should be charged with ANFO or a bulk emulsion of established performance. Upper perimeter blastholes should be charged with a bulk explosive with a much lower effective density. But where geology varies considerably, greatest control over overbreak could possibly be achieved with the versatile pre-assembled charge shown in Figure 1. This paper presents numerous potential ways in which the total cost of development can be minimised. It concentrates on recommending blast design features and the safe, rapid, cost-effective implementation of designs.

Jan 1, 1998

By M Ind, B Usher

Environmental regulators are increasingly adopting risk-based approaches to protect aquatic ecosystems. The Australian and New Zealand Environment and Conservation Council (ANZECC) and the Agriculture and Resource Management Council of Australia and New Zealand (ARMCANZ) (2000) introduced a risk-based approach to water quality guidelines that use decision frameworks to adapt water quality guidelines to local environmental conditions. Environmental quality objectives are no longer a simple ‘pass or fail’ number such as restricting total suspended solids (TSS) concentration to a specified limit for a particular rainfall event. This approach ignores spatial and temporal variability and the complexity of aquatic ecosystems. The risk-based approach establishes levels where adverse effects may occur. If these objectives are not met, further risk-based investigation is undertaken to assess the potential impact to the ecosystem. Klohn Crippen Berger (KCB) developed a dynamic simulation to predict the variability of sediment discharges, which is applicable for risk-based impact assessment of aquatic ecosystems. The application of the methodology over the life of a mine site is illustrated using a proposed South Pacific mine.The site location is in extremely rugged terrain with a high annual rainfall of approximately 4.7 m. There were two major sediment ponds proposed to reduce sediment discharges. A sediment and hydrology model was developed in Goldsim to provide daily estimates of run-off flows and sediment concentrations. A modified algorithm based on the Australian water balance model was created and incorporated into the Goldsim model and calibrated using recorded field data.The sediment module was developed based on a Revised Universal Soil Loss Equation (RUSLE) assessment, an annual prediction of soil loss over a catchment. A land-use type erosion vector was developed for different land-use types and for each of the subcatchments, a subcatchment erodibility vector was calculated. This vector and the daily rainfall erosivity factor were used to estimate the daily soil loss. The estimated soil loss and the modelled run-off yielded predictions of daily sediment concentrations. Finally, a sediment settling module was used to predict the daily efficiency of the sediment ponds and hence discharged sediment concentrations.The results of this modelling form the first part of a quantitative risk-based assessment into suspended solids impacts. The second part is the assessment of the effects of these predicted TSS concentrations on aquatic ecology. As part of the feedback-loop required in a risk management framework, if the environmental quality objectives are not met then further management decisions and actions may be required to reduce the risks presented by suspended solids. This may include modifications to: the mine-development plan; construction techniques and scheduling; processing techniques; rehabilitation strategies; or hard-engineering solutions such as sediment basins or flocculation.The Goldsim water-balance model provides a quick and efficient method of testing potential remedial actions on predicted sediment loads and concentrations. In combination with a cost-benefit assessment, options for reducing sediment releases from the mine site can be effectively and quantitatively compared thereby providing mine operators with a basis for decision-making. Regulators can also be satisfied that potential impacts to aquatic ecology have been comprehensively assessed and the necessary management decisions have been initiated to limit risk to the environment.CITATION:Ind, M and Usher, B, ?2014. A dynamic sediment simulation to predict the variability of suspended solids concentrations over life-of-mine for application to a risk-based environmental assessment, in Proceedings Life-of-Mine 2014 , pp 191–204 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By S Strong, L I. Sanz Vivanco, T Brown

One of the most significant technical and practical challenges facing the tunnel construction team on the Legacy Way road tunnel project in Brisbane, Australia was how to erect the prestressed precast concrete slabs to form the smoke duct in the tunnel boring machine (TBM) tunnels.An essential part of the tunnel ventilation system, the smoke duct extends the full length of the 4.6 km-long twin two-lane tunnels. The vast majority of the tunnels (approximately 4.3 km) were constructed using two 12.4 m diameter double-shield TBMs. The refurbished Herrenknecht machines broke several world records on the way to completing the tunnel excavation works in just over nine months. With the excavation complete the focus turned to solving the complex civil tunnel fit-out challenges. A key component of the civil fit-out of the tunnels was constructing the smoke duct in the TBM tunnels, which was designed as a precast solution.The slabs, which each measure 8.62 m long × 2.0 m wide × 200 mm thick and weigh close to 9?t, need to be erected above cast in situ corbels whilst other tunnel finishing works continue. The space-proofing clearance offered by the design to the support corbels below and the precast segmental lining above was in the order of only 100 mm.This paper tells the story of how the Transcity Joint Venture (JV) tunnel fit-out team comprising some of Europe and Australia’s leading tunnel construction specialists drew upon the global strengths of the existing JV member companies and the global reach of leading TBM manufacturer Herrenknecht to develop an innovative system in solving this challenging problem. This globetrotting story, which starts in Australia, visits Europe and mainland China before returning to Brisbane where it all began.CITATION:Brown, T, Strong, S and Sanz Vivanco, L I, 2014. How the global experience and reach of tunnelling’s true multinationals helped solve a road tunnel fit-out challenge, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 507–512 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Lloyd F, Arnold D. A, Hagan T. O

This paper investigates the problems that are encountered in mining at extreme depths. It looks into the rock mechanic aspects, especially the high stress levels that will occur, and the hazard of rockbursts. Furthermore, environmental problems are discussed, with refrigeration and reduction of neat loads being major methods of maintaining ,sorkable conditions. The paper concludes that it will be of tmost importance to have a planning team of Tne highest quality to ensure that conditions are maintained so that work can be carried out safely and under reasonable conditions.

Jan 1, 1986

A new plant for grinding limestone was built at the Risdon Works of the Electrolytic Zinc Company of Australasia Limited to meet increasing process demands expected to reach 150 tonne/day of ground limestone. Plant specifications included open- circuit wet grinding, a single ball mill, a feed sizing of minus 6 Tyler mesh, a product sizing of 100 per cent minus 200 and 95 per cent minus 325 Tyler mesh and for the plant to be unmanned during normal running. Main features of plant and equipment are described; grinding performances given, as well as operating experience since commission- ing of the plant in March, 1976.

Jan 1, 1977

During 1991 - 1993 the author interviewed approximately thirty senior managers of varying responsibilities in either the engineering, construction or operation of a heavy industrial facility. The purpose of the exercise was to determine the factors driving a deterioration of the working relationship between the engineering and the operating company following practical completion of a major project. From the research a number of conclusions have been drawn as to the root cause of the deteriorating relationship. For this paper we are drawing on this initial research and our ongoing experience of solving problems of this nature to present some fundamentals that can be used to break the breakdown maintenance cycle.

Jan 1, 1998

By Salley J, Gould WD

The stack-gas scubber effluent from base metal smelters often contain 20-100 ppm of oxidized selenium salts. Due to their toxicity, these must be removed from solution prior to release of the effluent to the environment. Many species of microorganisms including Corynebacterium diotheriae, Neurospora crassa, Candida albicans, Escherichia coli and various species of Salmonella are capable of assimilating oxidized selenium and reducing it intracellularly to red amorphous selenium. CANMET in cooperation with several companies has developed a biological process to recover selenium from dilute solutions. The laboratory, mini-pilot plant and the large industrial pilot- plant studies leading to the development of this process will be described.

Jan 1, 1990

By M Saghaeian, A H. Baladastian, A Dehghani Ahmadabadi, V Sheikhzadeh, R Hejazi

With the declining of high-quality hematite and magnetite iron ore reserves and the increasing accumulation of material resulting from mining and beneficiation operations that appear as lowquality depots and discharged materials in tailing dams, the necessity of recycling these reserves is increasingly becoming a critical demand. The Chadormalu iron ore mine is among the largest deposits of magnetite-hematite iron ore in Iran. In this mine, the total wet processing tails accumulated in tailing dams are over 92 Mt containing 25–40 per cent Fe. Laboratory and pilot tests on tailing samples led to the design and implementation of the Chadormalu Tailing Recovery plant (CTR) with a unique process circuit in Iran. In the CTR plant, after three steps of re-pulping with spiral classifiers and sanding machines, the underflow is concentrated by two stages of WMIMS and produces 64 per cent Fe grade magnetite concentrate. The tailings of the drums are mixed together and introduced into the hematite recovery section, including two stages of VPHGMS separators, and 60 per cent Fe grade hematite concentrate is produced. This plant has been in operation for over ten years with a total yield of 18.93 per cent. Due to changes in the materials extracted through new tailing dams, the quality of the final concentrate dramatically dropped to 56.36 per cent Fe and 0.79 per cent P; therefore, applying reverse flotation and removing phosphorus from the final concentrate was inevitable. By using this approach, upgrading of the concentrate to 63.01 per cent Fe and 0.05 per cent P was obtained. Furthermore, regarding the high amount of phosphorus in the tailing streams, direct flotation has been designed to produce apatite concentrate as a by-product stream through a flotation system comprising series banks of Rougher, Cleaner, and Re-Cleaners flotation cells. Hence based on the results, at optimum conditions, a final apatite concentrate with a yield of 15.78 per cent and 14.06 per cent P could be achieved. Successful implementation of this project has led to the production of magnetite-hematite and apatite concentrates with annual capacities of 250 000 and 45 000 t, together with total yields of 11.59 per cent and 6.19 per cent (includes de-sliming of apatite flotation feed), respectively.

Aug 24, 2022

By N Meadows, M Rodriguez

A 200 000 tpa heap leach demonstration plant was approved by the Murrin Murrin Joint Venture (MMJV) in December 2005 and engineering commenced in January 2006. The demonstration plant will utilise stockpiled ore reject material (æscatsÆ) and extract nickel and cobalt. Limited production from the demonstration plant is expected by the end of 2006. The demonstration plant will enable the company to fully investigate and understand all associated technical issues over the next 12 to 18 months, including the potential to expand the heap leaching operation to a commercial scale. In parallel, the MMJV will continue a research and development program to improve and expand the application of its heap leaching technology.

Jan 1, 2006