Search Documents

By M Thompson

"The Jaguar concentrator, 60 km north of Leonora, Western Australia (WA), consists of a standard closed circuit semi-autogenous grinding (SAG) and ball mill producing a float feed of approximately 60 micron at 70 t/h. Following comminution, separate copper and zinc concentrates are produced by differential flotation. These concentrates are subsequently dewatered by thickening and then filtration.Separate audits of the Jaguar Operation’s copper and zinc concentrate thickeners were conducted to evaluate their performance, following occasions where site personnel had identified unnecessary loss of copper and zinc concentrate to the thickener overflow. The feedwells were identified as the source of the observed problems due to the following issues with their design/duty:lack of retention time in the feedwell as current design is completely opennot conducive to effective mixing required for efficient flocculationdiameter of the zinc concentrate thickener feedwell was undersize for its duty.To improve the performance of the thickeners, it is planned to replace both concentrate thickener feedwells with a high rate design for their respective duties in February 2016. The audits also identified that the feed system requires modifications with particular importance placed on minimising air entrainment of slurry into the thickener feedwell. Minimisation of air entrainment is hoped to be achieved by providing constant head pressure through installation of weir arrangements in the feedboxes and redirecting each feed pipe so that it feeds tangentially into the feedwell. In addition, improvements to the control philosophy of both thickeners will be made with the installation of an ultrasonic bed level probe and bed mass sensor, in order to make real-time adjustments to the underflow pump speed to maintain steady state operation.Following the feedwell replacement and modifications to both thickeners it is expected that losses of recovered copper and zinc will decrease to undetectable levels. Subsequently it is anticipated that a more consistent, homogenous underflow can be produced for downstream filtration.Citation:Thompson, M, 2016. Concentrate Thickeners Feedwell Replacement, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 273–278 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By Christie AB

Stream sediment geochemical analyses from 140 mining company exploration surveys of the Coromandel, Northwest Nelson, Marlborough and Westland regions of New Zealand have been compiled from open file reports and entered on a database called REGCHEM (for Regional Exploration GeoCHEMistry). REGCHEM is supported by GEOEXPL, a custom-written computer software application which operates under the Microsoft Access relational database mangement system on a PC-type computer. The data are plotted as maps using the Maplnfo geographic information system (GIS) package. Thesholds separating anomolous values from background values are determined using the PROBPLOT univariant statistical package, which enables the descrimination and modelling of several populations. Relevant REGCHEM data are being incorporated into a GIS for the Coromandel region as part of ongoing studies to sevelop mineral deposit and metallogenic models for the region, and to assess regional prospectivity.]

Jan 1, 1995

By Smith E. L

The Ore Reserve/Exploration System implemented at Mount Isa for M.I.M. Holdings Limited is a comprehensive computer system designed to process assay, geological, structural and survey data input via special purpose logging sheets from daily activities at Isa Mine, Hilton Mine and various Carpentaria Exploration Company prospects. The system performs two basic functions; (1) data acquisition, validation and file maintenance to prepare the data for retrieval, and (2) generation of routine and optional reports. The types of reports available range from masterfile detail printouts and retrieval of data by key items to survey computations, structural analyses, cutoff calculations, statistical analyses and ore reserve calculations by the polygonal, inverse square or moving average techniques. The use of various optional reports available through the system is illustrated by several examples, and planned future development is discussed.

Jan 1, 1973

By Q Qu

Reliable prediction of longwall gas emission sources and rate plays a critical role in mine ventilation and methane drainage capacity planning. Over the years, Australian longwall mines have been using the historic Winter method and the Flugge method in modelling specific gas emissions (SGE). The predicted results often experience high discrepancies from the operational reality. To improve gas emission prediction, post-mining gas contents were measured in several mines in Qld and NSW by safely drilling core holes into the longwall goaf. The results revealed many new insights into gas emission characteristics from different coal seams and the drawbacks of the European methods in their use in high-production gassy Australian longwall mines. Based on measurement data, a new, time-dependent gas emission prediction model has been developed. Considering several factors such as caving, desorption and production rate, the new model can predict more accurate and meaningful gas emissions to meet today’s needs in mine gas emission management. A case study is provided to demonstrate the application of the new SGE model.

Oct 12, 2022

By K Henley

One of the greatest practical difficulties of measuring airblast occurs when a significant wind is blowing onto the microphone. Small windscreens are usually used to mitigate the wind noise on the microphone, but in some wind conditions, sound pressure levels (SPL) of over 120 decibel (linear) are frequently recorded. There are no specific procedures to mitigate the effect of wind noise when measuring airblast in any of the standards or guidelines pertaining to the measurement of airblast from blasting operations, other than the requirement to use an effective windscreen. A search for relevant literature was undertaken and measurements were taken over a period of six months at a test site using alternative microphone measurement methods. Previous researchers’ experiments with windscreens in silenced wind tunnels showed that wind noise can be reduced through the use of large diameter windscreens, and that at low frequencies, the windscreen size and the material type makes no difference to measured SPL values. Other researchers found that wind turbulence caused significant SPL measurement problems. A comparison with field data failed to explain the extremely high SPL recorded by the field microphones at wind velocities much lower than those used in wind tunnel testing. It has been concluded that turbulent airflow over and behind the microphone is a significant contributor to extraneous noise in airblast measurements in windy conditions. This turbulence can be generated by objects upwind of the microphone or by the microphone itself if the windscreen is ineffective. Reducing the wind speed over the microphone by placing it on the ground is the approach required by the international standard for the measurement of noise from wind turbine generators (IEC 61400–11). This paper presents data that illustrates the extent of the problem, reports on the trial of three different microphone mounting locations for measuring airblast from blasting and concludes that in windy conditions, microphones placed on the ground substantially avoid wind problems and do not reduce the measured SPL of the airblast.CITATION:Henley, K, 2015. Reducing the effect of wind on airblast measurement during blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 485–492 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By A N. Kusnanto, D Sims, L Henim, S Crispin, J Hertrijana

The high sulfidation Purnama Au-Ag deposit located on the Indonesian island of Sumatra entered production in mid-2012 following a two-year program of construction and development. Discovered in 1997 following a regional stream sediment geochemical sampling program by the Normandy Anglo Asia joint venture, it is the first and largest deposit in G-Resource’s Martabe Project to enter production and is the centrepiece of a series of six deposits totalling 8.1 Moz Au and 73.8 Moz Ag in Mineral Resources (G-Resources, 2013a).In 2011 investigation into the controls of high-grade mineralisation in isolated parts of the deposit identified a potentially significant mineralisation style which had not been previously recognised or accommodated in the resource model. An extensive investigation of core and logging data followed to confirm the distribution of the somewhat unusual mineralisation style – a sedimentary-like cavity infill of very high-grade auriferous pyrite within the steep hydrothermal breccia feeders to the system. With the bulk of mineralisation located within the adjacent volcanic sequence and sandy-matrix phreatomagmatic breccia surrounding the feeders, the lack of constraint for high-grade intersections in the hydrothermal breccia zones had potential to significantly impact the mine plan in the lower sections of the planned pit through overestimation of local gold grade. Combined with new data emerging from grade control drilling and infill resource drilling in the pit, a program of reinterpretation of the deposit was initiated to update the geological and alteration framework underpinning the resource model. The result has improved the economics of the project and added metal to the Ore Reserve for Purnama.CITATION:Sims, D, Henim, L, Hertrijana, J, Kusnanto, A N and Crispin, S, 2014. Remodelling the Purnama deposit – an interpretation case study from G-Resources Martabe Project, Indonesia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 229–236 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By J Loeb, J Dampney, P Cameron

Optimisation of Blast Design and Execution must be done right the first time. It is too late after the ore is broken. Consequences of poor design and execution negatively affect productivity from load and haul through the primary crusher to processing and hence reduce mine site profits. Harnessing and utilising ‘big data’ from geology, geometallurgy, drill hole location, powder loading, blast timing, blast movement and fragmentation to close the loop in blast design and optimise the blast increases productivity across the entire value chain from Mine to Mill. As the internet of things and artificial intelligence increases the quantity of data available, being able to capture and utilise this data to advantage is a challenge. Recent advances in software and hardware together with the increased power of cloud computing allows engineers to close the blasting loop to increase mine site productivity. Numerous case studies over the years detail significant gains from implementing the innovative technologies available to Mine to Mill projects. The opportunity is available for all members of the multi-discipline teams at each mine site to actively ensure productivity improvements are realised and maintained not only in their area, or silo of responsibility but across the entire mine site. This paper refers to recent case studies which outline how significant improvements in productivity are available to all mining operations to increase mine site profitability and dividends to shareholders.

Jun 22, 2022

By D Genge, E Martin, T Goswami, M Rothery

Rio Tinto’s Hunter Valley Operations is a large open pit coalmine situated in the heart of the Hunter Valley in Australia. The Riverview West Pit has faced increasing production challenges in recent times due to decreasing dragline strike lengths and increasing environmental constraints on vibration, overpressure and fume generation. Conventional mining techniques would involve five to six production blasts per strip to recover multiple coal seams. Each blast event carries the risk of exceeding the strict environmental requirements. By working collaboratively with Orica, it was realised that the blasting method known as Stratablast™, in conjunction with advanced computer modelling techniques, could provide productivity gains whilst simultaneously providing more control over the environmental effects and the impact on nearby infrastructure.As a result of this change, the number of blasts per strip was reduced to one, with the implication that a great deal of care and forethought was needed to manage the increased challenge posed by multiple constraints in the proposed mining area. This innovative approach of combining throw and stand-up blasts allowed the extraction of all major coal seams in a single pass blast event. The blasts were initially designed with a large factor of safety to stay within environmental limits as they were over 1.1 km in strike length, with more than 800 holes and with a total charge weight of about 1000 t of bulk explosives. Furthermore, there were conflicting priorities around the desired blast outcomes. So far, 11 such blasts have been designed and successfully fired. After each blast, innovative design changes have been iteratively implemented to provide further control over environmental impacts, whilst continuing to improve productivity. As a result of these changes, blasts have progressively increased in complexity with the inclusion of features such as damage zones, mid-splitting, time gaps and different directions of firing. The consequence of this complexity is that the blast duration can be as long as 28 seconds to accommodate all components of the blast.This project has increased the productivity of the Riverview West Pit through blast design improvements and allowed the environmental impacts to be managed with far more control and predictability than would have been possible under a conventional blasting regime. There still remains room for further optimisation of mine productivity and this is being addressed through a process of continuous improvement.CITATION:Goswami, T, Martin, E, Rothery, M and Genge, D, 2015. A holistic approach to managing blast outcomes, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 645–654 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By S McKnight, L Koroznikova, J Begelhole

"This paper outlines a simple methodology for iron ore characterisation. Iron ores commonly contain a range of iron oxides with varying iron content along with generally minor quantities of lighter silicate gangue phases, giving rise to density variations. Companies tend to rely on heavy liquid separation (HLS) in the evaluation of samples arising from exploration, mining or metallurgical processes. Heavy suspension separation (HSS), a simple laboratory technique of density fractionation, employing suspensions of fine tungsten carbide (WC) particles in lithium heteropolytungstate (LST) solutions, can be used in the evaluation of iron ore.As part of Arrium Mining’s program to improve its knowledge of ore types being processed in two hematite ore beneficiation plants (OBP), metallurgical evaluation of hematite feed and geometallurgical evaluation for the OBPs has become a major focus.Metallurgical evaluation of the hematite ore ultra-fine size fraction, formally treated as waste but now upgraded by HSS, is a part of Arrium’s program to improve recovery.The HLS method for iron ore characterisation is not generally used as part of routine iron ore feed metallurgical evaluation due to the expense, toxicity and time-consuming nature of the technique. Results show that the HSS method for iron ore characterisation can achieve low-cost, low-toxic separation and can be used on-site to improve turnaround time of results (Begelhole, Jasper and Koroznikova, 2013).Arrium have applied this technique successfully for the past three years to progress process improvement for the two OBP as well as to assist Arrium’s on-site laboratory services, Bureau Veritas in Whyalla.The main objective of this program has been to further develop the HSS procedures using a low-toxicity, high specific gravity (SG) suspension; LST and WC as the dense medium for metallurgical evaluation of ultra-fines.A suspension of a particular density will separate iron ore into two products: a sink fraction (denser iron oxide – hydroxide particles) and float fraction (silicate – iron ore composite particles). A theoretical grade and mass recovery can be calculated, and a grade – mass recovery curve can be constructed for iron.Metallurgical evaluation of the plant feed ultra-fine size fractions are used to improve efficiency of an upgrading plant process. This type of characterisation can be used to prepare feed piles of known processing characteristics, or to benchmark the performance of the process against what can be theoretically achieved.CITATION:Koroznikova, L, Begelhole, J and McKnight, S, 2016. Characterisation of Low-grade Hematite Ore Ultra-fine Size Fraction Particles by Heavy Suspension, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 327–334 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By O J. Restrepo Baena, S Nowosad, R Webber-Youngman, N Mojtabai, P Foster, A Binder, S Hazuria, erson, S Raval, L Liu

As the mining industry faces times of change, new challenges arise to ensure raw material supply for the younger and future generations. Different scenarios are currently shaping the way we mine and teach mining engineering. Led by an increasing demand for raw materials, net zero requirements for improving long-term operation performance, technological advancements such as automation and digitalisation, safety improvements, environmental considerations and a need for social acceptance, mining is pursuing to change and adapt to these requirements at a faster pace. Such changing times raise new concerns, one of the most relevant is the lower number of students interested or enrolling in mining engineering and related fields leaving mining engineering as one of the less preferred career options between the younger generations. Nonetheless, it is essential to continue addressing and supplying the skill sets that is suited to contemporary and future of the mining industry. To this end, globally, academia is currently undergoing several initiatives such as curricula updates and adaptation, up skilling, improving teaching practices and techniques, including e-learning techniques, enhancing industry-academia and inter-university collaboration, and much more

Sep 1, 2024

By S Natsui, Y Goto, S Kawanishi, J Takahashi, H Nogami

The demand for copper increases yearly, and further improvements in copper smelting efficiency using flash furnaces are required. This study was conducted to understand and promote the interfacial reaction associated with the collision of silica flux and iron oxide particles, ie the formation reaction of fayalite slag, in the reaction shaft of the flash furnace. High-temperature microscopy was used to observe the reaction behaviour of a 2 mm granular SiO2 reagent in contact with micrometreorder- sized FeO reagents in situ. When the amount of FeO was lower than the stoichiometric amount with SiO2, the molten slag formed at the interface between FeO and SiO2 diffused into the SiO2 particle before dissolving the remaining FeO particles. It did not contribute to the subsequent reaction, and despite having the lowest amount of FeO among the samples in this study, many unreacted FeO particles remained on the surface of the samples after testing. On the other hand, under conditions with high FeO content and close to the eutectic composition of the FeO-SiO2 system, a liquid phase formed from low temperatures, gradually increasing in volume and eventually completely dissolving the 2 mm SiO2 grain. These results indicate that the early-stage slag is essential in increasing the interfacial area between FeO and SiO2 and facilitating the supply of FeO to SiO2. In other words, the FeO/SiO2 determines the amount of liquid phase and significantly influences the subsequent interfacial reaction rate between FeO and SiO2. Therefore, the local FeO/SiO2 of the particles falling down the reaction shaft should also be optimised to ensure early slag formation. Meanwhile, the time required for 2 mm SiO2 to complete the reaction for the temperature history employed in this study was significantly longer than the particle residence time in the reaction shaft. Further detailed investigation of the effects of silica flux particle size, composition, and reaction temperature on the reaction time will help find the conditions under which the reaction of silica flux can be completed in the reaction shaft. These kinetic approaches could contribute to future innovations in the copper smelting process using flash furnaces.

Jun 19, 2024

By J Taylor, M Smith, A Tunnadine, D Nikolakopoulos

As Olympic Dam rapidly expands into the Southern Mine Area (SMA) the Mine Geology team has concurrently ramped up underground diamond drilling to sustain rates of above 175 km/a. With >10 underground rigs double-shifting, traditional paper sections used for the management of drill programs were no longer optimal due to scale of operations. An opportunity was identified to modernise monitoring of all underground diamond drill programs, through the integration of logged copper sulfide estimates with Olympic Dam’s first-fully integrated deposit-scale geological model in Leapfrog Geo. This paper describes the transition within the Mine Geology team from reliance on 2D paper sections, towards near-real time 3D geological modelling for optimising end-of-hole decisions in the field. This transition was enabled by innovative database solutions informing locally constrained implicit models, limited by a distance buffer around active underground fan drilling. Due to the high volume of historic drilling, there were significant computational challenges with the implementation of daily production style implicit models at Olympic Dam and initial testing of regular updates to implicit gradeshells and sulfide domains required in excess of 12 hrs to run. The enabling solution was to optimise the interfaces between the AcQuire database, Deswik MDM and Leapfrog Geo to create a dynamic, streamlined workflow that was easily completed by Mine Geologists in accordance with daily production duties. Geologists are now building rapid implicit models for a range of variables from an integrated data set of logged sulfide estimates and existing assays, spatially constrained by 150 m buffers around active drilling using a unique drill fan identifier flagged during the planning phase. Once the live-implicit models are updated, they are exported for visualisation on field tablets to be used during logging and core checks at the start and end of every shift. To manage the risk of ‘going digital’ interpretation remains at the forefront of the drill section close-out process, with Mine Geologists critically reviewing the finished sections on a standardised template with new learnings wireframed and communicated to stakeholders. The Live Field Model has enabled a step-change in the geological effectiveness of diamond drilling, reducing over – and under-drilling ore-waste at Olympic Dam continuing to push drilling effectiveness towards 20 per cent of intercepts >2 per cent Cu. In addition, upside or risk identified during the proactive management of drilling execution can be rapidly capitalised or mitigated.

Mar 22, 2022

By Reeve JS

Heap leaching is a low capital cost alternative to conventional processing techniques for gold recovery from areas that contain small gold particles in a porous host rock.For successful heap leaching the ores to be leached must maintain good permeability after being stacked into heaps so that the leach solutions can percolate evenly through them.The presence of clays, slimes or excessive amounts of fines can hamper the flow of leach solutions causing channelling and producing dormant or unleached areas within the heaps. This results in unreasonably long leach periods and poor extractions. In extreme cases the clays or fines completely seal ore heaps, causing leach solutions to run off the sides of t'he heaps rather than penetrate the ore.The Northern Queensland Company uses the Agglomeration Heap Leach technique (AHL) to overcome the difficulties associated with clays or fines. This technique involves cementing the fines, by using readily available binders, into a rigid, porous network that greatly enhances uniform flow of cyanide leach solutions through the ore heaps.

Jan 1, 1986

Better quality at lower cost is today's formula for remaining competitive in a world market. For an integrated steel company, high quality low cost steel production must originate before the blast furnace. In 1979, when U.S. Steel initiated a Quality Management Program throughout its steelmaking operations, efforts began at the coal, ore and flux mines. The objective was to improve the quality and reduce the variability of the critical parameters for steelmaking raw materials, to get the blast furnaces, and subsequently the melt shops, under optimum control. The general details of U.S. Steel's Quality Management Program are discussed and how it was used to promote the desired improvements in steelmaking raw materials. Some of the outstanding results obtained by the cooperative efforts between the mines and the steel plants are reported. The lessons learned by U.S. Steel were through upgrading existing operations and facilities. These principles should now be applied to new projects and the benefits of good quality management should commence from the time new projects are Commissioned.

Jan 1, 1986

By B McFadyen, Y Potvin, K Woodward

The Australian Centre for Geomechanics (ACG) held two workshops in 2019—one in Australia and one in Canada—to discuss processes and methods currently used in the mining industry for stope design and reconciliation. In practice, this work strives to optimise stope performance and aims to maximise ore recovery (minimise underbreak), while minimising dilution (overbreak). One of the key findings from the workshops was that current stope design practices, almost exclusively, rely on some versions of the empirical Stability Graph methods developed in 1980s. Although robust and useful at the feasibility study stage, there are a number of inherent shortcomings with this approach. The Stability Graph’s limitations first lie in that it cannot assess underbreak, which is a very important measure of performance. Furthermore, the method doesn’t consider a number of factors which often have a critical influence on stope stability, for example, drilling and blasting or the presence of faults. Given the current industry standard practice, there is a great opportunity to reinvent the stope design process to optimise performance. A finding of the workshops was that every mine quantifies stope performance in terms of volume reconciliation with a focus on dilution and ore losses, and reconciling metal tonnes recovered from the mill. Many mines further investigate stope performance by looking at individual stope faces and the causes for the deviations between the planned stope shape and the measured cavity. Recent research at the ACG has shown that investigating overbreak and underbreak at a higher resolution is a powerful way to identify the root causes of overbreak and underbreak. Finer scale assessment is achieved using an octree analyses, which effectively divides the relevant stope volume into cubes on the scale of a metre and produces many tens of thousands of data points. The octree data structure and subsequent analysis underpins a data-driven stope design methodology. The ACG is currently developing a design approach based on multivariate modelling methods that can account for the many variables that influence stope performance and forecast stope overbreak and underbreak results. Back-analysing stopes based on octree reconciliation results provides a rich database for training the model. Once the model can achieve reliable forecasting of overbreak and underbreak, an interactive drill-and-blast design will allow for the assessment of different firing strategies to optimise stope performance.

Mar 15, 2021

By K Barns, H Law, T Whebell, P Scobie, T Perkins, J Siliezar, M Larson

With processing a variety of orebodies at Glencore’s Ernest Henry Mining (EHM) has come a changing mineralogy and more complex requirements for treatment in the concentrator. From mid-2013 and into 2014 the grind size required to achieve sufficient mineral liberation for production of a quality concentrate has reduced significantly. What was once a final P80 of 35–45 microns was forced to 20 microns. This has necessitated some creative changes to the flow sheet that previously had a 937?kW Vertimill regrinding a rougher concentrate to 40 microns. EHM is able to utilise an existing M10 000 3 MW IsaMill previously used for magnetite processing, to provide a quick convenient solution without large scale capital expenditures. Operating the Vertimill and IsaMill in parallel in closed circuit was successful at reducing the P80 of the regrind circuit to below 20 microns which increased the final concentrate grade by four per cent. This circuit and intermediate circuits used are discussed. Performance of the Vertimill and IsaMill is compared for efficiency optimisation to improve the overall circuit performance.CITATION:Siliezar, J, Whebell, T, Perkins, T, Law, H, Scobie, P, Larson, M and Barns, K, 2014. From magnetite to chalcopyrite – a story of versatility and efficiency at Glencore’s Ernest Henry mining?operation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 85–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By C A. Cooper, G A. Suter

The sizing of a starter dam for a Tailings Storage Facility (TSF) involves balancing many competing demands. It should cost as little as possible, be high enough to store tailings until the first raise can be constructed, it must be able to contain water safely, and it must be designed in such a way that the long-term integrity of the higher raises are not compromised, among other things. In addition to these demands there is the complication of the behaviour of the process plant, and the tailings during commissioning. Variations in slurry density, excess water in the TSF, initial settled density of the tailings, reliability issues, and beach slopes above and below water can all impact the way the tailings beaches are developed and ultimately impact the ability of the starter dyke to contain the required volume of tailings and water.The conventional approach to the design of a TSF starter dyke is to begin looking at the elevation required for a set of deterministic design parameters, find ways to reduce the size or volume of it as much as possible to reduce cost, and then possibly look at the sensitivity of some of the input parameters. This paper discusses a stochastic modelling approach for starter dykes that allows a wide range of design inputs to be simulated quickly, with an envelope of possible results produced. The sensitivity to different parameters can also be examined to understand which design inputs have the biggest impact on the required dyke sizing. By integrating the 3D TSF modelling tool Muk3D with GoldSim, it will be demonstrated how a wide range of scenarios can be evaluated and how that information can be used to make better decisions about the selection of design options.CITATION:Cooper, C A and Suter, G A, 2018. Starter dyke optimisation with Muk3D and GoldSim, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 466–475 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Stevenson I, Dickinson W, Taylor R. N

Despite flash smelting's widespread use little is known about the actual processes taking place in flash furnace shafts and comparatively few reports of sampling campaigns have appeared in the published literature. his paper reviews the previous reports of the use of horizontal trough samplers and analyses their expected collection efficiency. In the light of the deficiencies revealed by this analysis an isokinetic sampler was produced and a vertical sampling technique was also developed to obtain samples from directly below the burners in the shaft of the flash furnace at the Kalgoorlie nickel smelter. Comparison of the sizing of the samples obtained with the horizontal trough and isokinetic samplers confirmed the theoretical analyses and showed that the trough samplers were not collecting the fine particles. Besides providing data to validate mathematical models of the burners and shaft, chemical analyses of the shaft samples showed that the coal in the charge was reacting preferentially and that the plume of at least one of the burners was being deflected from its axial position. In the region directly below the burner there was evidence that the disperser on the burner was imparting more momentum to the coarser particles and that these were concentrating in the outer regions of the particle plumes issuing from the burners.

Jan 1, 1992

By N Pirouznia, F Rashidi Nejad, S Naraghi

Sungun Copper Mine, which is the second largest copper mining operation in Iran has a large tailings storage facility with a seepage control dam located downstream of the main dam. Surface and groundwater in surrounding area of the tailings storage facility has been monitored for ten years. This paper will discuss the results of the surface and groundwater monitoring and seepage control at the Sungun Copper Mine. The results of the study show that if the tailings storage facility influence the water quality of the rivers, this effect is not significant, so that the prevailing parameters of the measured parameters were within the permissible standard of drinking water in Iran.CITATION:Rashidi Nejad, F, Naraghi, S and Pirouznia, N, 2018. Surface and groundwater monitoring and seepage control at the Sungun Copper Mine, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 439–453 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By G R. Ballantyne, V Souto, K Bartram

Particle sorting allows partially liberated minerals to be separated prior to energy intensive fine grinding. Sensors select particles for separation and air, water or mechanical ejectors are used to physically deflect those selected. To achieve effective separation there has to be sufficient liberation, accurate detection and presentation of a separated monolayer of particles. These three physical constraints determine the particle size limits, the sorting technology utilised, the separation efficiency, and the throughput that can be achieved. The combination of all these factors controls the effective limits on the degree to which sorting can reduce the specific comminution requirements and increasing energy efficiency. This paper will explore two case studies: the application of sorting in base metal mining and precious metal mining.CITATION:Ballantyne, G R, Hilden, M, Bartram, K and Souto, V, 2018. Characterising energy efficiency of particle sorting, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 531–540 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018