Search Documents

By J McQuie

The concentrator at WMCÆs Leinster Nickel Operation has operated with flash flotation in the grinding circuit since the early 1990s. There has always been a positive correlation between flash flotation Ni recovery and overall Ni recovery û however this relationship could be explained by differences in the ore, rather than by the action of the Flash flotation cell in reducing overgrinding of Ni. In July 2003, refurbishment within the plant made it necessary to operate the concentrator for a period with the flash flotation cells off. The resulting data set provided evidence that flash flotation in the grinding circuit changes the size distribution of Ni to reduce the amount of slow-floating fine (-7 ¦m) Ni produced. Ni recoveries in the finer size fractions were similar with flash flotation on or off û but because less fine Ni is produced when the flash flotation cells are operated, overall Ni recovery improved.

Jan 1, 2005

By B Belle

In a deep, gassy predrained coalmine, ventilation and goaf drainage systems act as critical controls to manage longwall (LW) panel return gas levels. The goaf capture efficiency of most LW panels ranges from 45 to 85 per cent based on the gas domain at respective workings. Recent operational experiences have indicated that 50 m goaf hole spacing is optimal for management of high production retreat gassy LW panels, where the probability of goaf hole failures are frequent. Due to the horizontal stress direction geotechnical issues, goaf hole failure just behind the LW face is a recurring challenge resulting in significant and immediate increases in LW panel return gas levels. This paper presents a successful implementation of an innovative LW tailgate (TG) road cut through seal goaf fan/venturi system. The system incorporated a 17' (400 mm cased) hole drilled to 320 m deep in a perimeter roadway on a retreating LW TG road drawing the working seam horizon goaf gas behind the perimeter of seals. The surface goaf fan/venturi system was aimed to safely exhaust the LW deep goaf gas and thus withhold the goaf stream spillage to TG drive area and reduce the panel gas load by controlled operation of the system using continuous monitoring of CH4, CO and O2 levels. This control philosophy was made operational without impacting the use of the perimeter inbye ventilation shaft used for mine cooling and providing additional ventilation dilution capacity. The instantaneous reduction in TG gas levels of up to 0.3 per cent was observed even when the LW was 300 m away from the c/t seal goaf hole. Success of this concept TG seal goaf gas control system used even when the LW was 1300 m outbye has become an inventory of additional control for future deep and long LW blocks. This paper attempts to share the design process in addressing other risks and desired outcomes in managing the LW gas levels.CITATION:Belle, B, 2015. Innovative tailgate mobile goaf gas management in two gate road longwall panels – concept to implementation, in Proceedings The Australian Mine Ventilation Conference, pp 31–40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Restarick CJ

The development of mathematical relationships to describe grinding in continuous rod and ball mills has involved two methods of approach and has resulted in two main types of "model." The first which has been used for full scale grinding systems has depended on the analysis of, for example, the effect of change in solids feed rate on the changes in overall size distribution which the feed undergoes to become the product as a result of passage through the mill operated under steady conditions. The resultant mathematical relationships are of matrix form and do not include any description of the flow characteristics of the systems. The second approach has made extensive use of a technique in which a "pulse" of selected tracer mineral, of chosen

Jan 1, 1970

By B P. Banerjee. S Raval, P M. Ranasinghe

Simultaneous Localisation and Mapping (SLAM) is an important technology that enables autonomous robots to navigate independently and create detailed, real-time maps of their surroundings. This capability is crucial in underground mining settings, where it enhances operational efficiency and significantly strengthens safety in these subterranean environments. SLAM algorithms typically rely on identifying and using distinct geometric features, such as plane and edge features, to understand the spatial layout of the environment and to track how it evolves as the sensor moves through it. In underground roadways, the scarcity of noticeable edge features, coupled with the repetitive nature of walls and corridors, poses a significant challenge, making it difficult for these systems to distinguish one area from another. Furthermore, the absence of global navigation satellite system (GNSS) signals in underground adds more challenges, leading to the accumulation of errors in both the mapping and localisation.

Sep 1, 2024

By Hemingway J, Read T. A, Anderson V. G

IN the determination of very small amounts of lead, the usual analytical methods are far from being satisfactory. Small amounts of lead may be present in the reagents empioyed, and it is customary to run a blank experiment to correct the error arising in this way. When the correction is of small magnitude compared with the amount of lead in the sample, this procedure may be adopted; but when very small amounts of lead are being determined it may happen that the lead found in the blank is as much, or even more, than the lead actually present in the sample, and the analysis has to be rejected. Moreover, the blank experiment cannot check errors which are not common to the blank and the analysis itself eg, the apparatus used in the parallel experiments, etc. It seemed to be desirable, tl;l.erefore, to make an investigation of the problem to ascertain, as far as possible, the nature of the errors arising from the introduction or loss of lead during the analysis, and how far these could be eliminated or corrected for; also, to determine the limits of accuracy of the improved method and the minimum amount of lead that could be reliably estimated.In the investigation, reliability and sensitiveness were regarded as essential features. Speed of operation, on the other hand, was considered of less importance. The amounts of lead dealt with being usually less than 1 mg, there is no alternative to the use of a colorimetric method. The latter, depending as it does upon the development of a brown coloration when ammonium sulphide is added to a very dilute -solution of a lead salt, is far from being a characteristic test for lead. Indeed, it is well known that the salts of most of the commonly occurring metals interfere with this test. Hence it is of vital importance that the lead should be isolated in the form of a pure compound possessing quite definite and characteristic properties before the colorimetric estimation is proceeded with...

Jan 1, 1921

By Mitchell D

In recent years the need to provide increased ventilation to improve environmental conditions rather than to dilute firedamp has led to increasing interest in the use of recirculation. Present UK mining law prohibits recirculation in ventilation, but it has been permitted selectively by exemption granted by Hm Inspectorate of Mines and Quarries. The conditions of use imposed by these exemptions to safeguard the safety and health of miners are examined in detail, dealing separately with primary and auxiliary recirculation systems.

Jan 1, 1988

The products of the steel tube industry play an important part in the production,' transrzission and refining of oil. Steel tube manufacturing is already well established in Australia and supplies the petroleum industry with its requirements" within the .present limitations of the various tube plants., With the discovery of oil in commercial quantities in this country, the steel tube industry could be expected to extend its scope to cover a much wider range; of oil country tubular goods, line pipe and refinery. Tubing.

Jan 1, 1962

By G Stovpchenko, G Jianjun, L Medovar

Electroslag remelting (ESR) today and into the future, will still be the main process for producing high-quality ingots by suppressing segregation, not just refining chemical composition from impurities. This paper analyses state-of-the-art electroslag refining with a focus on ESR with consumable electrodes, and recent technology with liquid metal supply (ESR LM) in view of their refining abilities and development trends, taking into consideration that the size of the ingots required by industry continues to grow, and the composition of new materials sophisticates to withstand increasingly higher mechanical and temperature loads . The yield of suitable metal in large ingots produced by conventional casting is low due to problems of element segregation by height and crosssection. For example, conventional ingots for nuclear powerplant rotors today reach nearly 700 t in weight. Attempts to directly replace such giant ingots with big-diameter ESR ingots weighing approximately 400 t were also unsuccessful because of growing segregation. Modern ESR equipment and technologies produce 200–250 t of ingots of satisfactory quality, reaching 2.5 m in diameter, implementing the change of consumable electrodes during remelting to increase ingot length. Another way to mitigate segregation is to enlarge the smaller diameter ESR ingot by a 500– 800 mm coaxial layer to the desirable diameter by ESR in the current-supplying mould (CSM). Modelling and experiments prove that refining from impurities and non-metallic inclusions at ESR most effectively occurs at the slag bath and liquid metal pool interface because the ESR LM has provided the same desulfurisation. ESR’s special refining capabilities in CSM come from the much longer time of LM residence shown at titanium purification from hard-melting nitride inclusions that are unremovable in vacuum arc remelting (VAR) and electron beam melting (EBM). Implementation of ESR technologies in CSM, especially with LM supply, is prospective to produce heavy enlarged and hollow forging ingots with prevented development of segregation due to dividing cross-section and reducing overheat of solidifying metal.

Jun 19, 2024

By Lu S, Zhou S

The flash smelting technology employed in Jinchuan demands a better mineral processing concentrate with an MgO content below 6.5 per cent. Two ways for MgO removal have been investigated in detail based on properties and process mineralogical characteristics of the rich ores in the number one mining area in Jinchuan. The key to the first way is the use of a new flowsheet which has two-stage grinding and separation followed by single-stage regrinding and multi-stage cleaning for the rougher concentrate. The second approach utilises two novel reagents, AT-131 and AT-202, which have been developed recently. Excellent metallurgical performance has been obtained in a commercial test and a batch test, respectively. The MgO content of flotation concentrate can be reduced to about six per cent.

Jan 1, 1996

By O Aydan, R Ulusay

Blasting is the most commonly used excavation technique in mining and civil engineering applications. Blasting induces strong ground motions and fracturing of rock mass in rock excavations. Particularly, high ground motions may also induce some instability problems of rock mass and structures nearby. Furthermore, it may cause some environmental problems due to noise as well as vibrations of structures near the populated areas. Furthermore, flyrocks is another major issue for the safety of people and damage to machinery and equipments when blasting is employed. In this study, the authors explore the ways how to estimate the ground motions as a function of distance, amount of explosive, number of holes. The ground motions were measured by stand-alone accelerometers developed by the first author and some empirical relations are developed. The effect of ground motions on the instability issues of benches such as sliding, toppling and rockfalls were investigated. Furthermore, the flyrock issue is investigated and some empirical relations to estimate the maximum distance of flyrocks from the blasting relations are compared and discussed. CITATION:Aydan, O and Ulusay, R, 2018. The ground motions induced by blasting in open pit lignite mines and its environmental effects, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 142–151 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By A B. Jahed, Ö Aydan, T Ito

In this study, the authors compiled some case history data and present some typical examples of rock slope stability issues in Afghanistan with a special emphasis on Kandahar region and categorise rock slope failures according to the principles of modern rock slope engineering. The slopes considered involve rock-cut, natural rock slopes mainly. The effect of structural geology and discontinuous nature of rock mass on both slope-cuts and natural rock slopes is taken into account and some preliminary assessments on the stable and unstable rock slopes are presented. Furthermore, the seismic effect on their stability is also considered. It is also pointed out that similar issues could be observed in open pit mines, which may be exploited in years to come.

Nov 29, 2022

By T Mizuta, D Ishiyama

The Vienna Wood hydrothermal is hosted by mid-oceanic ridge type basalt in graben morphology and is located in the Central Manus Basin. The hydrothermal field is about 300 metres in diameter and consist of a sulphide mounds and tall huge death and active chimneys. From the three distinct ore types collected from the Vienna Wood site, the dominant ore minerals recognised are pyrite, wurtzite, sphalerite, chalcopyrite, Fe-oxide and gangue minerals of anhydrite, gypsum, barite and silica. The consistencies in the paragenetic sequence and in the spatial distribution of the sulfides across the three ore types suggest that similar hydrothermal process exist across active and death chimneys. Fluid inclusion studies reveal a homogenisation temperature of 190-260¦C and an average salinity of 5.1-5.4 wt per cent NaCl equiv. The pH of the hydrothermal fluid ranges from 4.2 to 6.1. Bulk chemical analyses indicate that the mineralisation in the Vienna Wood can be classified into the Zn-(Cu-Pb) type of mineralisation. The tenors of the ore and mineral assemblage resemble those of the Mid-oceanic ridge system and ancient ophiolite hosted massive sulphide deposits of Cyprus and Oman.

Jan 1, 2002

By Golubkov OL, Fedotov PB, Shkylar FR

One of the fundamental parameters of the race- way is its extent (a{ o), which has a significant effect on the distribution of gas and material flows in the lower region of the furnace. pp The known relationships for determination of aC o in most cases link the length of the raceway with the parameters of the blast, while the para- meters of the coke layer, in which the raceway is formed, are either ignored or else expressed in terms which are difficult to determine experimen- tally. Furthermore, the coke combustion propert- ies are not always taken into account in current blast furnace operating practice with combined blast. A complex dimensionless parameter, which re- flects the properties of the interacting media, is the ratio of the kinetic energy of the hot, com- bined gas stream to the potential energy of the coke flow, burning at the tuyere in a gas of known composition. Statistical processing of experimental data on the extent of the raceway zone, obtained from literature and our own work on operational furnac- es, has led to a working formula of the following Form:

Jan 1, 1981

The Lower Proterozoic metasediments of the Pine Creek Geosyncline form a chrono- stratigraphic sequence of mainly greenschist- and amphibolite-grade shallow-marine to supratidal pelites, psammites, carbonate rocks, and volcaniclastics which in places rests unconformably on Archaean basement. Granite and later dolerite intrude the sequence, and are associated with the major orogenic 1800-m.y. event which regionally metamorphosed the sediments. Most mineralisation is stratabound, and can be related at least partly to volcanic activity. Uranium mineralisation is mainly confined to particular carbonate-rich horizons near basement. Other metals are mainly in small hydrothermal deposits near intrusive granite. Specialist studies indicate that uranium was leached from its source rock, and probably carried as carbonate complexes in highly saline fluids at between 100 and 3500 C. Precipitation took place by redox reactions in breccia zones in carbonate rocks; these zones were formed by carbonate solution or diapiric movement of evaporites which preceded the carbonate. Extensive chloritisation in the ore zones suggests metasomatism by Fe- and Mg-rich fluids which may have evolved during dewatering of the evaporites. The main mineralising event took place after the 1800 m.y. metamorphism, and was probably

Jan 1, 1979

The output of Dexin Pit Copper is up to 33 million tonnes a year and the final depth is more than 500 m. As a cost reduction measure, the in-pit crushing and conveying system has was introduced to deliver ore from the pit to mills. This paper describes the in-pit crushing and conveying system, and highlights the optimum level where the shovel-truck haulage system transfers into In-pit Crushing and Conveying system, relocation of an in-pit crushing system, and includes the impact of the transferring point when the costs change.

Jan 1, 2003

By S Sims, A Stradl, G Hope, B Lacouture

Column flotation cells have been installed in numerous base metal operations around the world. The majority of these cells utilise conventional air-only spargers to introduce air into the bottom of the column. The recent development of instruments to measure the bubble characteristics in these columns has provided a renewed understanding of column behaviour. These new tools provided insight into why the columns at Red Dog Mine had never performed up to expectations. After efforts to optimise the spargers failed to substantially change the bubble size and air efficiency, alternate sparger systems were investigated. The Metso Minerals CISA Microcel sparger system appeared promising and was selected for a full-scale plant trial. The Microcel sparger system was originally developed for the coal industry at the Virginia Centre for Coal and Minerals Processing. In October 2003, a Microcel was retrofitted into one of two 3.66 m diameter flotation columns in the zinc retreat circuit at Red Dog Mine. The operation of the two different sparger systems in parallel allowed a detailed comparison. This paper discusses the performance of the Microcel based on the data collected during several detailed surveys. Bubble size measurements carried out in the pulp zone using the McGill University bubble viewer showed a significant difference in bubble size. The mean Sauter diameter of the bubbles decreased from 3.4 mm for the jetting-type sparger to 1.9 mm for the Microcel sparger. The overall recovery and the recovery by size fraction for both valuable and gangue minerals were compared. Paired t-tests demonstrated that the Microcel column produced a higher concentrate grade (0.6 per cent zinc absolute) and a higher unit recovery (2.8 per cent zinc absolute) than the existing Canadian Process Technologies Inc (CPT) SlamJet column. These improvements provided a payback period of 1.5 months for the $109 000 investment.

Jan 1, 2005

By Z Li, Z Yan, M Yang

Recycled cement paste (RCP) is a kind of CaO-rich recourse, which is separated and recycled from waste concrete. Due to its chemical composition, RCP could partially replace lime as a flux and be loaded into electric arc furnace (EAF) steelmaking process. Rapid RCP assimilation and liquid slag formation have significant effects on EAF steelmaking process. In this study, the dissolution behaviours of RCP and lime at temperatures of 1400°C to 1500°C were investigated using static dissolution experiment. The dissolution rate, interfacial microstructure, as well as dissolution mechanisms were discussed. It was found that the dissolution rate of RCP was much higher than that of lime. RCP could be completely dissolved into slag in 60 secs at 1500°C. The dissolution rate of lime was in range of 3.910-4 g/(cm2ꞏs) to 2.610-3 g/(cm2ꞏs), while that for RCP was in range of 1.510-3 g/(cm2ꞏs) to 4.910-3 g/(cm2ꞏs). As for lime dissolution, a dense layer of dicalcium silicate (C2S) generated at the dissolution interface, and the diffusion of Ca2+ in C2S layer was the limited step for lime dissolution. Some of calcium ferrite could be observed at the interface between lime and C2S layer. As for the RCP dissolution, there is no obvious product layer of C2S formed at the dissolution interface, Fe2+ continuously diffused into RCP layer during the dissolution, and small amount of FeOꞏMgO solid solution generated and gathered at the dissolution interface. The dissolution rate of RCP in EAF slag was quite higher than that of lime, partially add RCP as flux in EAF could accelerate the slag formation process.

Aug 21, 2024

By A M. Robertson, R Lefebvre

Air movement and associated oxygen transport through waste rock dumps has the potential to significantly enhance the rate of oxidation of pyrite-bearing material. While this is a desired outcome for most heap leach operations, airflow in waste rock storage facilities can result in significant increases in generation and acceleration of acid rock drainage. Hence, a good understanding of internal airflow through waste rock dumps is required to control ARD and minimise any associated liability. The principal mechanisms contributing to airflow and oxygen transport in a waste rock pile include: diffusion; advection due to a thermal gradient (chimney effect) and/or wind pressure gradients; and advection due to barometric pumping. While diffusion is typically limited to a near-surface zone of a few meters depth, advection and barometric pumping have the potential to move air (and oxygen) to much greater depths into the pile. In general, the more permeable the waste rock material, and the greater the height-to-width ratio of the waste rock pile, the greater is the potential for advective air movement. The reactivity of the waste rock material as well as the coarseness (hence air permeability), and the spatial variability of these properties within a pile, have a strong influence on the magnitude of thermally induced advection. In contrast, air movement due to barometric pumping is controlled by the waste rock porosity, changes in ambient air pressure and the heterogeneity of air permeability of the waste rock dump. Results of field monitoring and numerical modelling using TOUGH AMD are presented to illustrate the concepts on air movement in waste rock piles discussed in this paper. During the design and construction phase, airflow can be controlled by judicious placement of reactive waste rock and use of selective placement techniques to control the internal structure of the waste rock facility (eg introduction of horizontal layering, prevention of inclined, high-permeability, channels (æchimneysÆ)). Several closure measures are available to minimise airflow including: placement of a low-permeability cover to reduce air entry; and placement of a non-reactive cover material to isolate reactive material from the zone of active airflow and/or regrading of the waste rock pile to obtain a geometry and internal structure less susceptible to advective airflow.

Jan 1, 2003

By G J. Zhang

The shape and particle size distribution of caved ore mass in sublevel caving were investigated in this study. The paper first reviews the main factors affecting the shape and characteristic of caved ore mass in sublevel caving and then through the experimental blast testing with cement-sand concrete models, the shape and particle size distribution of caved ore mass were found out. The experimental results indicated that the shape and particle size distribution of caved ore mass was similar to that of the drawn loose body. This finding presented a new perspective for the future study on the ore drawing theory and on the optimisation of structural parameters of sublevel caving. The structural parameters must meet the principle that the shape of the drawn body is in consistency to the shape of caved ore mass.

Jul 11, 2011

The results of about 30 years of exploration and mining activities and research studies in the Kambalda mining district, Western Australia, have led to general agreement that the komatiite-associated Ni sulphide ores formed as a result of igneous processes (Ross, 1974; Ross and Hopkins, 1975; Gresham and Loftus-Hills, 1981; Cowden, 1988; Lesher, 1989 and many others). Despite this agreement, the controls on sulphide supersaturation and concentration of the resulting sulphide in a limited zone, remain uncertain and controversial. A major uncertainty is the source of sulphur in the ore deposits. Two principal sulphur sources have been proposed: 1. komatiite lava/magma (Hudson, 1972; Naldrett, 1973; Lesher et al, 1981; Cowden, 1988; Foster et at, 1995), and 2. sedimentary material (Groves, Barrett and McQueen, 1979; Lesher, Arndt and Groves, 1984; Lesher, 1989; Lesher and Campbell, 1993). Resolution of the uncertainty regarding the sulphur source is required for a complete understanding of the controls on ore formation, which in turn would significantly impact exploration strategies in the Kambalda mining district and elsewhere. This paper reviews the constraints on sulphur sources for the komatiite-associated Ni sulphide ores in the Kambalda mining district. The focus is on the general characteristics of the ores and surrounding rocks: individual ore deposits are not described, though specific examples are noted where appropriate. The stratigraphic and volcanic settings and geochemical (major and trace element and isotopic compositions) characteristics of the ore deposits and surrounding rocks are considered within the context of the competing sulphur source models, and future directions of research in the district are noted.

Jan 1, 1996