Search Documents

By P J. Harris, C T. OÆConnor

Collectors are used to impart hydrophobicity on particles thus increasing their chances of reporting to the froth phase. Also, the extent to which naturally hydrophobic gangue particles, such as talcaceous minerals, report to the froth can be reduced by the use of depressants. Thus the use of collectors and depressants will directly influence the extent to which hydrophobic particles report to the froth. However these hydrophobic particles will also have a direct effect on the characteristics of the froth phase, more strongly hydrophobic particles causing a reduction in the stability of the froth with the expected concomitant effects on grade and recovery. This study included microflotation (ie frothless flotation) and batch flotation of various ores using a number of different collectors and depressants and a newly developed froth imaging device (SmartfrothTM). Flotation performance was characterised by mass and water recovery, and recoveries and grades of the valuables. This paper shows how the various reagents influenced the behaviour of the pulp and froth phases. The critical importance of managing the type and dosage of reagents used in flotation with a view to optimising their influence on the froth phase is discussed.

Jan 1, 2005

By J Kleynhans, D Vermeulen, V Cogho

A number of rehabilitated open cast coalmines in SA are already decanting. The paper focuses on the situation at one of these mines where the following information exist: monthly decant rates and rainfall; sulfate concentrations of the decanting water; water level measurements inside the mine prior to decanting; ABA analyses; information about the rehabilitation (drainage slope, vegetation, soil used). A 2D-model was constructed for the mine and calibrated against six years of flow data. About 85 per cent of the decant outflow rate comes from direct recharge on top of the rehabilitated mine while the other 15 per cent is derived from lateral groundwater inflows. The estimated recharge value was 17 per cent of the rainfall. Measured sulfate values showed that the sulfate generation rate for the mine was in the order of 7 kg/ha/d. Conclusions from the study are:most of the water decanting from rehabilitated open cast coal mines is derived from recharge via rainfall; given a specific sulfate generation rate, then: the lower the recharge the less the decant rate but the higher the sulfate concentration of the decanting water and vice versa; future prediction of the decant rate must be stochastic according to expected percentile monthly rainfall values; and as a first assessment of the predicted sulfate concentration of decant water from rehabilitated open case mines, the 7 kg/ha/d sulfate generation rate can be used.

Jan 1, 2003

By Anderson JDC

Opencast Lignite Mining requires topwall strata of seams to be fully depleted and footwall aquifers sufficiently depressurized. To prevent a spread of the cone of depression into protected wetlands some distance away, alternatives had been investigated such as closing water works, underground slurry wall barriers and recharge by infiltration. As a result of these investigations, the infiltration method has been chosen and in a first phase during the next decade it will utilize as much as 55 x 106 m3/year. Using this approach, the survival of the wet lands is assured.

Jan 1, 1988

By Rath M. C, Das R. P

Studies were carried out on dissolution and oxidation of iron powder in ammonia-ammonium carbonate solution using oxygen over pressures. Cobalt and nickel losses during iron oxidation under different conditions were investigated. Regression equations were derived for percent cobalt loss and percent iron oxidation using ammonia, ammonium carbonate and oxygen partial pressure as the variables. The equations were tested for adequacy using Fisher's test. Cobalt losses increased with the increase of initial cobalt concentration and about 400 mg/l of cobalt was lost from a solution containing 500 mg/l cobalt. A maximum of about 80 mg/l nickel was lost from 1 g/l nickel containing solution, and this loss remained the same even when the nickel concentration was increased to 7.5 g/l.

Jan 1, 1992

Through the use of structural analysis programs such as Unwedge and considering the shear strength of applied fibrecrete it can be shown that fibrecrete can provide a higher factor of safety in a ætypicalÆ underground development excavation than standard rock bolts. This paper describes the progression of ground support from an æas requiredÆ component of mining to the use of bolts and surface support as a mandatory requirement. With the mandatory requirement for surface support, fibrecrete has been considered and applied as a secondary feature but simple analysis and practical observations indicate that it may be considered as primary support. The key elements to its implementation are: When is it safe to work under fresh fibrecrete and how do we practically determine this? How much ground support does fibrecrete provide? How can we reduce the cost of fibrecrete? An examination of these questions indicates fibrecrete can be much safer,less expensive and quicker to install than normal ground support elements. This paper explores practical examples from sites where significant benefits have been achieved by mine operators.

Jan 1, 2005

By G Munro

he Melbourne City Link project will complete a missing link between two existing major freeways in the Melbourne road network, providing a much needed bypass of the Central Business District for through traffic. The project, which is being financed under a BOOT arrangement with the Victorian State Government, involves the upgrading of significant stretches of existing freeway and the construction of new sections involving viaducts and tunnels. The tunnel sections, which are the focus of this paper, are beneath residential and business areas, the Yarra River, the Royal Botanic Gardens and significant sporting facilities where surface construction would be either impossible or unacceptable (reference Figure 1). The shorter, 1.62 km west bound Domain tunnel comprises two cut and cover sections through Olympic Park then the Yarra River, the driven section of 0.68 km length and exits through a common cut and cover section with the east bound tunnel under St Kilda Road and Sturt Street. The longer 3.76 km east bound tunnel commences at the common portal, through cut and cover under St Kilda Road then 2.86 km of driven section before exiting at a cut and cover section at Burnley. The longer Burnley tunnel has an access and ventilation shaft at approximately its mid point.

Jan 1, 1999

This paper describes the mechanical and electrical maintenance activities as practised at Isa Mine. The principles of preventative maintenance adopted are described as well as the basis of maintenance cost control.

Jan 1, 1978

By M J. Nugus, S C. Dominy

Mesothermal lode-gold deposits often pose problems during sampling because of their complex and erratic gold grade distribution, and the presence of coarse gold. Effective sampling and sample preparation protocols must form the basis of any resource estimate at whatever stage a project is at. Design of a sampling regime must be based upon a thorough understanding of orebody mineralogy and geology. This should include consideration of gold particle size and distribution. The sample type, size and density employed must also be based on the underlying geology of the deposit. Choice of sample preparation procedure and assay type is of critical importance if fundamental sampling error and analytical errors are to be minimised. Traditional fire assays, using small charge sizes, consistently understate assays gained from large charge sizes and techniques such as screen fire assay and bulk leach extractable gold assay. The proportion of coarse gold within samples will have a profound effect on the requirements for sample preparation and assay method. The application of Gy sampling theory can help to reduce errors within the processing of samples of broken rock. Quality control/assurance of sampling regimes must also be critically assessed. The problems associated with sampling mesothermal lode-gold type deposits are presented as case studies from Western Australia and North America.

Jan 1, 2003

The Oregon-Idaho graben evolved after widespread Uwleiitic flood basalt volcanism associated with the arrival of the plume head of the Yellowstone hotspot beneath southeastern Oregon approximately 17-16 Ma. The north- to north- northeast-trending, 50 km-wide graben evolved between 15.5 and 10.5 Ma during east-west extension. The graben is part of a middle Miocene back-arc rift (1,100 km long) that includes the northern Nevada rift, the Baker and LaGrande grabens, and the Chief Joseph dike swarm of the Columbia River Basalt Group. The graben ceased to be a volcano- tectonic depression as the cross-cutting western Snake River plain began to evolve at approximately 10.5 Ma.

Jan 1, 1995

By R E. Gerald II, B Zhang, T Sander, J D. Smith, J Huang, R J. O’Malley, H Tekle

In the steelmaking process, mold fluxes are essential for ensuring thermal insulation, refining, and the efficiency of continuous casting. Real-time understanding of the in-service composition of slags and fluxes are crucial for optimising the steel production process and improving the quality of the final product. An in situ fibre-optic Raman probe that enables the study of the structure, composition, and viscosity of molten slags and fluxes at steelmaking temperatures has been developed and demonstrated both in the lab and in foundry scale experiments. The focus of this study is on the structural, compositional, and property analysis of molten fluxes in a laboratory setting, with the aim of applying this technology for in situ monitoring during industrial production. Raman spectra were successfully collected at various temperatures from 1000°C to 1400°C in real-time and analysed using a deconvolution algorithm to isolate and quantify peaks in the spectra associated with the specific structures of molecular components in molten and solidifying flux. The research successfully combines in situ Raman spectroscopy with high-temperature viscosity data, specifically targeting CaO-CaF-SiO2-Al2O3 based mould flux systems. Specified ratios of the deconvoluted Raman peaks, such as Al-O-Al/Si-O-Si ratio, shows good correlation with the flux chemistry, while the Q3/Q0 peak ratio shows good correlation with viscosity. A ruggedised Raman probe system was also developed and demonstrated in an 80 kg induction furnace. Ultimately, the goal of this work is to demonstrate in situ slag and mould flux analysis in industrial processes, such as in the continuous caster or electric arc furnace (EAF).

Aug 21, 2024

By Karlson R, Rispin M

Chemical admixtures are not commonly included in the variety of backfill mixes used in the mining industry. This may be attributed to several reasons including, but not limited to: the perceived high added cost, 2. the lack of awareness about their proper use, and 3. the lack of knowledge about their features and benefits. In the construction industry today, however, chemical admixtures are used in the majority of the concrete produced, enabling concrete to become a more cost-effective building material. They also enable construction crews to meet demands for year-round construction, quicker completion of construction projects, and improved concrete properties. The high demand for chemical admixtures in the construction industry has led to numerous innovations in admixture technology in recent years. Some of these chemical admixtures have been found to enhance the production, transport, placement, and in situ properties of backfill mixes. Others have been found to reduce the cost of such mixes while maintaining, and in some cases improving, their physical properties. In this paper, a few of such innovative admixture technologies are discussed. The benefits, imparted by these technologies to backfill mixes as well as performance data on their use in several backfill applications at various mines, are presented.

Jan 1, 1998

The first record of coal discovery in Australia dates back to 1791 when escaping convicts found coal in the banks of a creek just south of Newcastle. Development in the Newcastle Coalfield was the sole source of supply for the colony and for export until the 1850s when mines were established in the Southern & Western Coalfields. The important Hunter Coalfield was not discovered until 1873 when coal was found at Rixs Creek near Singleton: The first exploration drillholes were commenced in 1799 using drilling equipment obtained by Sir Joseph Banks. From 1820 to 1850 several famous geologists (naturalists), including the Rev W. B. Clarke, J. D. Dana and Strzelecki, wrote reports on the coal measures in New South Wales. The first Government Geo- logist, Samuel Stutchbury, was appointed in 1850. The major coal deposits of the State are contained in Permian Coal Measures in the Sydney-Gunnedah and Oaklands Basins. Coal quality ranges from high volatile, high moisture thermal coal at Oaklands to low volatile hard coking coal in the Southern Coalfield. Most coalfields can provide a range of steaming and coking coals.

Jan 1, 1988

By A K. Raina, V M. S R Murthy

Rock mass response in blasting is an important element to determine the performance of a blast along with its other outcomes. The near-field monitoring for rock mass response analysis is vital for determining the behaviour of a blast; however, due to costly and cumbersome methods involved in such measurements the subject has received scant attention so far and the publications on this account are perfunctory in nature. This paper presents a non-destructive method to monitor the blast-induced pressure in the rock mass at a distance from a blasthole. The methodology of monitoring and a few examples of actual field monitoring are detailed in this paper. The responses of the rock in the near-field of a blasthole under dynamic loading have been documented to predict fragmentation and throw. The proposed method has also been used in limited cases earlier by the author to predict flyrock using a semi-empirical method and trajectory equation. The pros and cons of the method are discussed while throwing light on the actual response and the prediction of fragmentation and throw of blasted rock.CITATION:Raina, A K and Murthy, V M S R, 2015. Measurement of blast-induced pressure in bench blasting and deciphering explosive performance through rock mass response analysis – a methodology, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 501–508 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J T. Carswell, K Sutton

Quality control (QC) of reverse circulation drill sampling commonly involves regular duplicate subsampling to monitor the extent of imprecision or random error in the subsampling system. In gold mining in Australia, the subsampling tool is usually a cone splitter.Other sources of error, including delimitation error and bias (systematic error) in the subsampler are often assumed to be negligible or ignored for being too difficult to QC.This paper describes actual sampling errors and error mitigation based on quality assurance and quality control (QA/QC) of surface and underground reverse circulation drill sampling at a high-nugget gold mine at Sunrise Dam, Western Australia.CITATION:Carswell, J T and Sutton, K, 2014. Sources of sampling error and implications for quality assurance and quality control in surface and underground reverse circulation drilling, in Proceedings Sampling 2014 , pp 65–70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By Selischop F, Tredoux M

The distribution of platinum-group elements (pGEs) has been investigated in matte and slag samples from Waterval Smelter (Rustenburg Platinum Mines). The study showed that a strong preference of PGEs for alloy phases in matte represents a concentration mechanism that commenced in the furnace but can be considered a continuum from natural processes. Metal losses to fayalite (converter) slag occur by matte entrainment due to the mechanical capture of liquid sulphide droplets from the matte layer, and the exsolution of dissolved metal sulphide resulting from changes in the oxidation state of the slag. The latter is comparable to immiscible sulphide in basic magmas. However, the observed distribution of PGEs shows enrichment in metal phases of the matte. A mechanism is proposed whereby naked PGEs in silicate melts coalesce to form clusters which are stabilised by surface attachment of sulphur atoms. This envelope acts to 'draw the cluster into sulphide melts. Small particle melting effects permit PGE clusters to remain as liquids at magmatic and smelter temperatures.

Jan 1, 1994

By N Gruber

In the continuous casting of ultralow carbon (ULC) steels, free carbon is used to control the melting behaviour of mould powders. If the carbon is not completely removed during melting, it is enriched at the top of the slag pool. Liquid steel may come into contact with this layer because of the turbulence of the molten metal, resulting in its recarburisation, which negatively affects the desired product quality. Thus, a reduction in carbon input is desirable. For this purpose, SiC and/or Si3N4 with and without antioxidants were selected as melt-control additives to replace carbon in the mould powders. Thermodynamic calculations were performed to quantify their effect on the melting behaviour based on the chemical composition of a flux already applied to ULC steels. To experimentally assess the liquefaction behaviour, laboratory mould powders were prepared and annealed in steel crucibles closed with a lid. Crucibles were inserted into a furnace that was already preheated to selected temperatures between 900–1200°C for 10 mins and quenched to room temperature. Subsequently, the samples were mineralogically investigated. The results confirmed those obtained from the thermodynamic calculations. Si3N4, and SiC in particular, are suitable raw materials for delaying the solid-solid reactions of raw material components during melting. Owing to their stability at high temperatures, the necessary SiO2 content to form a liquid phase is not available, resulting in lower amounts of the liquid phase. The addition of antioxidants to delay the oxidation of SiC further reduces this positive effect. Attempts to decrease the SiC content without negatively affecting the melting behaviour resulted in a reduction in the CO2 emission by at least 27 g CO2/kg of mould powder when compared to the carbon-containing standard mould powder. These investigations revealed differences in the melting behaviours of granules and loose powders, which are related to their respective production processes.

Jun 19, 2024

By E Garbarino, P Molina, V Badino

Given the ever increasing quantity of construction and demolition waste (C&DW), one of the most challenging issues presently facing policymakers and public administrators in Italy concerns how to organise and manage collection and recycling and to understand whether and to what extent recycled aggregate can complement natural building aggregates in a sustainable supply mix (SSM). The paper presents the results of a research aimed at analysing energy and environmental implications of the C&DW recycling chain in the administrative territory of Provincia di Torino in northern Italy. In respect of a population of about 2.25 million inhabitants, the annual production of C&DW in the area under study is 1.8 Mt. A combined geographical information system (GIS) and Life Cycle Assessment (LCA) model was developed, paying attention to the geographical location, land use, transportation network and avoided landfill: crucial issues for sustainable planning and management. Around 90 recycling plants were classified according to the size, typology (stationary, semi-mobile and mobile) and physical- mechanical characteristics of the recycled aggregate. Under different assumptions relevant to the delivery distance, and considering the typology and grade of recycled aggregate, as well as local availability of natural aggregates, it was possible to evaluate the geographical coverage of aggregates demand and to use LCA in order to identify and quantify energy and environmental indicators.

Jan 1, 2009

By E Jak

A viscosity model has been developed for both completely liquid and heterogeneous, partly crystallised slags in the Al2O3-CaO-æFeOÆ-SiO2 system in equilibrium with metallic iron. The Urbain formalism has been modified to describe the viscosities of the liquid slag phase over the complete range of compositions and a wide range of temperatures. The Roscoe equation has been used to describe the effect of presence of solid suspension (slurry effect) on the viscosity. The parameters of the viscosity model were optimised to describe large experimental data set in the low-order subsystems, as well as in the multi-component system. The computer package FACT was used for prediction of the proportion of solids and the composition of the remaining liquid phase. The model provides a good description of the experimental data (over four thousand experimental points) in liquid phase, and liquid + solid mixtures, over the complete range of compositions and a wide range of temperatures. This model can now be used for viscosity predictions in industrial slag systems. An example of the application of the new model to slag cleaning and reduction smelting processes is given in this paper.

Jan 1, 2000

By T Mahlangu

The leaching of gold in alkaline aqueous cyanide solutions may be reduced significantly by the passivation of the gold by a surface layer of polymeric aurocyanide. This passivation of the gold is typically countered by the presence of Pb(+2) species in solution, which may be present as an impurity in the solution, or specifically added for this purpose. The speciation and availability of Pb(+2) in typical cyanide leach solutions is illustrated as a function of pH, and the presence of S(-2), S(+6), Cu(+1) and Ag(+1) species. The probable role of the Pb(+2) species in efficient gold leaching is discussed.

Jan 1, 2007

By L M. Zhang, X Y. Li

Surface displacements are routinely monitored at multiple points during slope excavation. The monitoring data reveals the safety status of the slope under current loading conditions. They can be used to enhance the prediction of the future performance of the slope by reducing the uncertainties of the prediction model and its model parameters. In a multistage excavation, the observed displacements in the current stage can be used to update the prediction of the displacements in subsequent stages. Besides, due to the spatial correlation of the slope parameters, the prediction of the displacement at one location can also be updated using the monitored displacements at adjacent locations. This study aims to develop a multistep updating method to enhance the prediction of the future performance of the slope using time-series monitoring data at multiple points. This method integrates the theoretical computational model with observational evidence. It considers the inherent uncertainty of the slope, model uncertainty and measurement uncertainty. With more monitoring information being incorporated, the prediction becomes closer to the actual performance of the slope. A case study of a multistage excavation of an extremely high rock slope in south-west China is presented for illustration.CITATION:Li, X Y and Zhang, L M, 2014. Better prediction of performance of a slope using time-series monitoring data at multiple points in a multistep excavation, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 183–188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014