Search Documents

By F Jiao, J Wang

By the year 2000, China was the sixth largest gold producer in the world, with about one-quarter of total production being derived from refractory or semi-refractory deposits. Although bacterial oxidation plants had been previously tried in China using local technology, these plants had not been commercially successful. The Laizhou Gold Enterprise (Tarzan BioGold Co Ltd) located in Shandong Province, undertook to modernise their gold processing facility in 2000 with the introduction of Bacterial Oxidation (BACOX) Technology. In 1997 BacTech Australia and Mintek of South Africa had formed a technology partnership, combining forces in the provision of bioleach technology. Under a cooperation agreement, BacTech/Mintek were chosen as the preferred technology providers for this first application of commercially proven bacterial oxidation technology within China. The paper describes the successful operation of this plant over the last three years. The events of project implementation are described, from the metallurgical testing of concentrate; through to the commissioning at the design throughput of 100 tonnes per day resulting in 80 000 ounces (2.5 tonnes) per year of refined gold. Process aspects of the operation encountered over the last three years are discussed which illustrate the robustness of the operation. The success of the bioleach facility has led to an advancement of plans to double plant capacity and some of the innovations, which may be employed in this expansion phase, are discussed.

Jan 1, 2004

Fluid circulation occurs in oceanic crust of all ages, at the seafloor spreading axis, on mid-ocean ridge flanks, in the ocean basins, and in subduction zones. In the first three settings the fluid originates as seawater. At the axis and on the ridge flanks, the circulating seawater produces a major chemical exchange between the oceans and the crust. Based on heat budget constraints, between 10 and 40% of the river flux of Mg can be taken up during high-temperature alteration of the basaltic crust along the mid-ocean ridge axis. Most of the hydrothermal -heat loss, however, occurs on the mid-ocean ridge flanks, where the temperatures are lower and the seawater flux correspondingly larger. The estimated heat loss on the flanks is so large that upwelling must occur over a large fraction (5-30%) of the seafloor less than 65 Ma in age, at seepage velocities on the order of 10 to 100 cm/yr. The circulating seawater need lose less than 1 to 2% of its Mg content in order to solve the Mg mass balance for the oceans. Fluids in subduction zones are commonly less saline than seawater and are rich in methane and other light hydrocarbons. These fluids may originate by dewatering of the downgoing slab. If so, they may close the geochemical cycle of H2O that began with hydration of the basaltic crust at the ridge axis.

Jan 1, 1990

By G Davies, D Dunn, C Mawdesley, O Bertoli

The coal industry in Australia has been actively working in recent years towards the (re)integration of geostatistical techniques to the process of coal resource estimation. The benefits of using geostatistical techniques, over the current interpolation algorithms in use in coal modelling packages used to generate the grid estimates, need to be illustrated for the methodology to gain a broader acceptance in the coal industry. This paper focuses on the benefits gained at BHP Billiton Mitsubishi AllianceÆs Saraji mine for the estimation of the total product yield value at a 9.7 per cent product ash cut-off of a particular seam of the Saraji deposit. In order to perform this comparison, the results of the alternative estimation methodologies need to be benchmarked, which in most situations is achieved through the reconciliation of the estimates against production and/or process plant reconciliation data. Unfortunately, this benchmarking was not possible as no reconciliation data for the area of interest in the chosen seam was available, as it has not been mined at the time of the study. Where no reconciliation data is available, an alternative method is to use conditional simulations as the benchmark for comparison. The simulated values can be regarded as ærealityÆ, and the alternative estimation methodologies, based on a sampling of the underlying ærealityÆ, can then be compared using the simulated ærealityÆ as the benchmark for comparison.

Jan 1, 2009

By Mayer TE

The Granites Goldfield is located 550 km northwest of Alice Springs. Mineralisation was discovered in 1900 and intermittently worked along nine km of strike until the early 1950's, yielding a recorded production of 470 kg of gold. The geological environ- ment, pre-existing exploration drilling results, and an optimistic view on gold, prompted acquisition of the property by North Flinders Mines Limited in 1975. An agreement was signed with the Central Land Council in August 1983 and drilling commenced in the same month. In the past, gold was won from alluvial deposits, rich quartz veins and lower grade, disseminated stratabound mineralisation. The last is contained within a distinctive unit in the Mt. Charles Beds, of the Early Proterozoic Tanami Complex. This informally named "Host Unit" is a metamorphosed, chemical- pelitic sediment. The schist contains variable proportions of amphibole, quartz, garnet, clinopyroxene, carbonate and sulphide, inter- calated with recrystallised chert beds. Free gold occurs in several mineralised horizons within the Host Unit, generally conformably distributed within lithologic bands or at lithologic contacts. The Host Unit occurs within a sequence of metamorphosed pelitic sediments and intermediate volcanics. Although mostly confined to the Host Unit, stratabound gold mineralisation also exists in both Footwall and Hanging Wall Schists, usually within zones displaying certain Host Unit characteristics. The deposits may be loosely categorised as being of banded iron formation (bif) type, although some important differences are noted between them and classical bif type orebodies.

Jan 1, 1984

By Larsen D. F

Minor iron formation related base metal sulphide mineralization occurs in granulite facies metamorphic rocks of the early Proterozoic Willyama Complex. Rock sequences hosting three iron formation related Cu, Zn, Pb prospects from the Thackaringa Group (Suite 3) are described. A caparison of host rock sequences, style of mineralization and facies of iron formations suggests major differences in terms of the overall depositional environment. However, significant similarities are present with respect to the nature and distribution of iron formation facies and the occurrence of chlorite 'alteration' zones in close proximity to mineralization in all cases. The chlorite within these zones occurs in a number of diverse forms in a range of rock types. A comparison of the prospects shows that there is no evidence to indicate that the chlorite in the zones is a retrograde alteration product of former higher grade prograde mineralogies - the chlorite appears to have survived granulite facies metamorphism. The mode of occurence of the chlorite in the 'alteration' zones together with the fact that the association quartz + chlorite + magnetite + pyrite + base metals is cx rmn to all areas suggests that the chlorite is specifically related to the processes which deposited the stratiform iron formations and related sulphides. It is considered that the chlorite precursor was a prenetanorphic alteration product or chemical sediment closely related to submarine hot spring activity which was also the source for chemical sediment precursors of the iron formations, associated lode rocks and Sulphides.

Jan 1, 1983

By Whiten WJ

Although cone classifiers have received little attention in the modelling of mineral processing units they are one of the oldest non-mechanical classifiers. Their use has enjoyed a revival in recent years because of their low cost of installation and operation. In this paper the development of models for cone classifiers is reviewed and a new model is proposed. The experimental work, data collection and analysis are briefly described, and the new model is presented and discussed. The data used in the model development are made up from three distinct experiments using different units in each case. There are 21 data sets from a 3 m cone treating the tailings in a copper concentrator, 24 data sets from a 0.3 m pilot-scale cone, and 29 data sets from a laboratory glass funnel (0.(Y73 m diameter) used as a cone classifier, giving a total of 74 data sets. The model structure was developed from an analysis of particle settling in classifiers, using specialised model building software. The size of a particle settling in a separator and the forced flow through the apex of the cone were related via hydrodynamic dimensionless groups to the operating conditions of the unit. The model predicts the separation efficiency using the following four parameters: efficiency curve shape factor, cut-point, underflow density (per cent solids) or underflow pulp velocity. The model covers a range of feed flowrates from 1.2 to 5000 1/min.

Jan 1, 1993

By Mikula PA

This paper presents the results of in-situ and laboratory investigations into a mining method which utilises conventional continuous mining techniques to carry out two passes in thick coal seams, resulting in the development of stable pillars with relatively small width dimensions and heights up to 6 m. Geotechnical investigations included structural mapping, brightness logging and standard laboratory testing. Virgin stress was measured using overcoring techniques. Two approaches to pillar design were used in the study. These were; pillar design based on empirical formulae and laboratory testing, and pillar disign using calibrated mathematical models. A trial panel was developed at 300 m depth to study pillar deformation and stress changes due to mining. The extent of rib deformation was studied using borescopes and extensometers. In-situ geotechnical measurements were used to calibrate displacement discontinuity and finite element mathematical models of the coal seam. These models were then used to predict the behaviour of a small panel of pillars which were to be developed to 6 m height. The mining method was shown to be feasible provided adequate rib support was installed. The benefit of rib support was found to be two-fold, in that it increased confinement of the pillar in zones of low horizontal stress, while reducing horizontal stress relaxation in zones of high horizontal virgin stress. The possiblity of roof control by designing the small pillars to yield on retreat is discussed.

Jan 1, 1986

A recoverable uranium resource, shown to be suitable for in situ leaching, was discovered at Honeymoon in South Australia in 1971. Exploration of the deposit was carried out during the period from 1973 to 1979. Uranium mineralisation occurs in a coarse-grained unconsolidated sand aquifer located in the Yarramba Palaeochannel at a depth of approximately 110 m. Following initial development during 1979 to 1983 and the construction of demonstration leach facilities, the Project was put on hold. Southern Cross Resources purchased the Project in 1997. Government approval was received in March 1998 for the operation of on-site demonstration leach and recovery facilities while an Environmental Impact Statement was prepared and a 1000 tpa commercial production plant was designed. The Environmental Impact Statement (EIS) was released in June 2000 and operation of the test facility was completed in August 2000. Acceptance of the EIS by Commonwealth and South Australian state governments was announced on 20 November 2001. A Mining Lease was granted over the area of the proposed ISL operation on 8 February 2002. Operation of the Project is entirely dependent on using highly saline underground water resources to supply process and human needs. The management of discharge streams from the plant by re-injection was approved. The Honeymoon demonstration plant was the first adaptation of the solvent extraction process to highly saline in situ leach solutions. As such, it incorporated a number of unique operating and installation features. The trial period enabled optimisation of the process chemistry, additives and management and serves as an invaluable base for the proposed plant design and future operation. This paper discusses the nature of the uranium occurrence, the effect of saline water on the leach process and equipment, project design and environmental considerations, the requirements for disposal of discharge streams to minimise the impact on the arid environment and the requirements for rehabilitation following project completion.

Jan 1, 2002

By J Zhang, L Klemettinen, A Jokilaakso, J Biswas, J Partinen, H O’Brien, A Klemettinen

Waste lithium-ion batteries (LIBs) are important secondary sources of many valuable materials, including Critical Raw Materials (CRMs) defined by the European Union (EU): lithium, cobalt, manganese, and graphite. Additionally, LIBs typically contain nickel and copper, which are classified as Strategic Raw Materials for EU since 2023. In recent years, great effort has been made to develop efficient recycling processes for waste LIBs. Pyrometallurgical processes have been essential in industrial production of metals for many decades. These technologies are relatively mature, with high adaptability for different raw materials. Pyrometallurgical treatment in LIB recycling typically involves the use of smelting processes, in which waste batteries are heated above their melting points and metals are separated through a reduction reaction in the liquid phase. Through this recycling route, cobalt, copper, and nickel can be efficiently recovered in the form of a metal alloy, whereas lithium and manganese are lost in the slag phase. The goal of this work was to increase the recoveries of valuable battery metals through a combination of hydro- and pyrometallurgical unit operations. First, industrial Li-ion battery scrap underwent a selective sulfation roasting stage, where the aim was to transform LiCoO2 and Mn-oxides into Li, Co and Mn sulfates. After roasting, the battery scrap was leached in distilled water with a solid to liquid ratio of 100 g/L at 60°C and recovered 95 per cent of Li, 61 per cent of Mn and 35 per cent of Co. After leaching, the solid leach residue was mixed with industrial Ni-slag and biochar, followed by reduction at 1350°C in argon atmosphere. The high-temperature smelting experiments were conducted as a function of time (5–60 mins) to investigate the reduction behaviour of battery metals. The results show that Co and Ni from the slag and leach residue can be efficiently recovered in the slag cleaning stage.

Jun 19, 2024

By D Stepanenko, G Stovpchenko, L Lisova, D Togobitskaya, L Medovar

Classical electroslag remelting of consumable electrodes is a drop-by-drop melt feeding through a slag layer into a renewing molten metal bath, slowly solidifying into a homogeneous, dense, defectfree ingot in a copper water-cooled mould. The new look at the additive nature of the electroslag remelting (ESR) process in a protective atmosphere allowed us to formulate the principles of a comprehensive thermodynamic-based model that can predict dynamic changes in slag and metal composition at certain ingot remelting. The model considers drastically different slag-to-metal mass ratios at the beginning and end of remelting and predicts gas, slag and metal composition in a chain of thermodynamic subsystems. Despite consisting of calcium fluoride and stable oxides, the ESR slag can oxidise main and active elements from steel and alloys (primarily aluminium, titanium and silicon) due to chemical reactions between slag and metal. ESR is not an electrochemical process in its nature. However, slags are ionic melts and deviation in their composition causes a change in their properties, affecting both operation mode and ingot quality. Another important understanding derived from the modern metallurgy technological route is that the ability to refine metal from impurities is not a priority for the ESR because consumable electrode has already passed all stages of refining and deep degassing at ladle treatment that changes ESR slags engineering principles. The critical importance became slag’s ability to generate process heat and keep the melting composition in the metal bath unchanged (except for non-metallic inclusions assimilation). Slag engineering for ESR required a compromise between chemical inertness to a metal composition and desired physical properties deriving from technological reasons. The Directed Chemical Bonds Concept (DCBC) in a multicomponent oxide system was used to build predictive models of electric conductivity and the melting temperature of fluoride-oxide slag based on their chemical composition. Both models help to design a customised composition of effective slags for steel and alloy groups or individual grades, and they are significant steps in the development of a comprehensive model of electroslag remelting.

Aug 21, 2024

By H Kurth

Mining geologists utilise many technologies to map, sample, measure, model and plan before and during the mining process. Predicted ore quality rarely corresponds with feed quality determined by process operators. Objectively measuring conveyed material quality accurately in real time avoids disagreements over mined ore quality and generates opportunities to improve mill feed quality.This paper discusses the well proven PGNAA (prompt gamma neutron activation analysis) technology used in the GEOSCAN-M elemental analyser that is ideally suited to measuring composition of primary crushed conveyed material in real time. Representative, continuous, fully penetrative measurements are unaffected by particle size, belt speed, mineralogy, dust or layering on the conveyor. Material can be directed to processes or stockpiles by utilising measurement increments of typically one to five minutes and then activating diverters to direct increments to the correct location. Waste, low-grade or deleterious material can be rejected to waste dumps or stockpiled for later processing. Material meeting a product specification can bypass unnecessary processing. Paybacks in weeks have been achieved for such applications. Process operators are able to control the blend of ores fed into the mill to improve processing performance and use measurements for ore reconciliation and metal accounting. Utilising the technology to upgrade ore quality after mining and before processing is beneficial in improving plant economics.The technology has been successfully utilised in base metals, ferrous metals and industrial minerals. Mining geologists can determine ore quality being produced in real time and modify the ore quality prior to milling. Ore feed quality measurements are also used by process operators in optimising plant performance. The elemental content can help identify geometallurgical domains as well as other major changes in quality, which may affect processing. This paper outlines proven applications and case studies and proposes some innovative applications.CITATION:Kurth, H, 2017. Measuring ore quality using real-time on-belt elemental analysis – more than grade control, in Proceedings Tenth International Mining Geology Conference 2017, pp 213–220 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By D Reid

Characterisation of non-plastic segregating tailings presents a number of challenges: the material cannot typically be sampled in an undisturbed state, remoulded samples exhibit different behaviour to undisturbed samples, penetration test interpretation methods suffer from uncertainty in their application to many tailings and the tailings gradation changes considerably over relatively small lateral distances and depth. In addition, the process liquor of many Western Australian tailings contains large quantities of salt and other dissolved solids, which can further complicate laboratory test programs. To provide an insight into the variability at a typical gold tailings facility, four gradations of the material were tested to obtain critical state parameters. Historic surficial tube samples were collated and organised by gradation to establish the range of densities typical after settling and air drying. These were then compared to laboratory-accessible densities. Finally, tube samples were tested in the laboratory to observe if the large-strain material behaviour was consistent with the inferred critical state parameters for similar gradations. Site pore fluid was used in the testing of the tube samples in an attempt to assess if the pore fluid modified the critical state conditions of the material.The tube samples tested all exhibited strongly dilative behaviour in undrained shear. Of the four samples tested, only one exhibited behaviour consistent with the inferred location of the critical state line relevant to the material’s gradation. The reasons for the unexpected behaviour of the other three samples include layering within the samples, the potential influence of large quantities of salt in the pore fluid and likely differences in the gradation of the fines components of samples taken from mid-beach and the decant area.CITATION:Reid, D, 2015. Observations on the behaviour of a gold tailings with hypersaline pore fluid, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 191–200 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By S Karosiya, A Sharma, M Jain, N N. Viswanathan, M M. Pande, D Kumar, S Kumar

Desulfurisation of steel during ladle refining is governed by both thermodynamics and kinetics. For effective desulfurisation, thermodynamically, a low partial pressure of oxygen at the steel-slag interface and highly basic slag which possess a large sulfide capacity are desired. Kinetically, the mass transfer coefficient of sulfur in the liquid steel and in the slag determines the rate of desulfurisation. A fast desulfurisation rate is achieved by maintaining sufficiently strong argon stirring of the melt. In the present work, sulfur mass balance for steel and slag was performed after the desulfurisation treatment for several industrial heats. The decrease in the sulfur quantity of the liquid steel was more than the increase in the sulfur quantity of the slag. The discrepancy in the sulfur mass balance suggests that the sulfur could be transferred to: (a) the gas (via slag) phase; or to (b) the refractory (crucible) phase. The preliminary investigation of the refractory samples taken at slag-refractory and steel-refractory interface showed no interaction of sulfur with the refractory. Therefore, the possibility of sulfur transfer to the gas phase was verified by carrying out melting experiments of sulfur containing slag in an argon/air atmosphere. Sulfur containing slag was initially melted in an MgO-C crucible under an argon atmosphere followed by creating the air atmosphere just above the melt. Careful sampling and analysis from the cold spots of the crucible, much above the melt surface, revealed formation of a fibrous structure. Scanning electron microscopy energy dispersive X-ray spectroscopy (SEM-EDS) analysis of these fibrous deposits confirmed the presence of oxides and sulfides. Oxidation of sulfur containing slag under air atmosphere was also performed using a thermogravimetric analysis (TGA) set-up. It showed a constant sulfur loss in the range of 1300– 1500°C. Thermodynamic calculations carried out using FactSage™ ver 8.3 for these experimental conditions are in good agreement with the observed results.

Aug 21, 2024

By M S. Manono, K C. Corin

The optimisation and process developments surrounding the beneficiation of Cu-Ni-PGM ores is of fundamental importance when considering the continued rise in global demand for these precious metals. The selective sequential flotation of these ores is accompanied with various processing challenges such as the successful separation of the Cu-Ni-PGMs from non-sulfide naturally floatable gangue and pyrrhotite. Reagents such as sodium iso-butyl xanthate (SIBX) and sodium carboxymethyl cellulose (CMC) have proven to significantly improve the selectivity of the flotation process in their respective roles. The use of recycled water with abnormal inorganic electrolyte concentrations can modify the selectivity of these reagents, as ions may adsorb onto minerals such as pyrrhotite, thereby hindering or promoting the hydrophocity and floatability of pyrrhotite. Process water quality effects on the behaviour of pyrrhotite may have negative or positive influence on the recovery and grades of the wanted Cu-Ni-PGMs as valuable minerals associated with pyrrhotite such as pentlandite may be affected in like manner. Thus, the impact of concentrator process water quality on the behaviour of pyrrhotite needs to be determined. In this study synthetic process water at various ionic strengths was investigated against various CMC dosages to understand the behaviour of pyrrhotite during the flotation of a Cu-Ni-PGM Merensky ore in a batch flotation cell. This study showed that pyrrhotite grades increased with an increase in CMC dosage for fixed ionic strengths whereas the recoveries of pyrrhotite increased with an increase in ionic strength until 3SPW, then a trend of a decrease in recoveries was seen with 5SPW resulting in the lowest pyrrhotite recoveries. Furthermore, this study showed that moderate CMC dosages of 100 g/t resulted in the highest pyrrhotite recovery for all four ionic strengths of synthetic process water tested. It can be said that to maximise value recovery from Cu-Ni-PGM ores, understanding the behaviour of pyrrhotite against degrading water quality and reagent suites could be of paramount importance given the sensitivity of pyrrhotite to oxidising chemical conditions.

Aug 24, 2022

By M Camarda, A Pirson, F Vasconcelos, J Mesquita

ArcelorMittal Prijedor is a goethitic iron ore mine located in the north-west of Bosnia and Herzegovina, which mainly supplies ArcelorMittal’s European subsidiaries. Annual production of the asset stands at the level of 1.5–2.1 million tons of iron ore product which is sent to ArcelorMittal Zenica steelmaking plant. Two types of products with approximately 50 per cent Fe are generated in Prijedor through a process composed by crushing, screening, and magnetic separation stages. Within this process one of the tailings produced is called ‘ultrafines’. The ‘ultrafines’ product corresponds to the desliming hydrocyclones overflow in Prijedor plant, which is classified in a size fraction below 25 μm and corresponds to about 5 per cent of feed. This material is richer in iron than the coarser size fractions of the ore but do not present a good performance in concentration processes. In this way, several studies have been carried out during the last years to find solutions to use the ‘ultrafines’ material without success. In this context, the possibility of dehydroxylate the goethite contained in the material transforming the mineral into hematite and thus increasing the iron grade of the final product was investigated. During the research, several dehydroxylation tests with different temperatures and time of exposure were performed. Using dihydroxylation process at temperatures higher than 800°C it was possible to produce a material with 43 per cent Fe from the original 39 per cent Fe ‘ultrafines’ sample. In addition, the dehydroxylation tests confirmed that goethite becomes completely transformed into hematite at 400°C (with an exposure time of 60 mins) and material is completely sintered at 1200°C. A simulation study based on dehydroxylation tests results showed that it would be possible to use a ‘ultrafines’ product with Fe grade higher than 45 per cent to produce a material with 50 per cent Fe through a complete dehydroxylation process.

Sep 18, 2023

By J R. Manuel, M J. Peterson

Selected drill core samples from a Ferrobamba-limestone-hosted, magnetite-haematite skarn deposit, located in the Apurimac department of the Andahuaylas-Yauri skarn/porphyry belt of south-eastern Peru, were mineralogically and texturally characterised to gain a preliminary indication of the deposit's potential as an iron ore resource. Optical microscopy, X-ray diffraction (XRD) and scanning electron microscopy/electron probe microanalysis (SEM/EPMA) techniques were utilised to determine the characteristics of magnetite, haematite and/or goethite dominated ore types, including variations in the relative proportions and textural relationships of the ore and gangue minerals. The deportment of elements deleterious to processing performance (eg copper, sulfur and potassium) was determined and the beneficiation potential of the samples was briefly assessed. In drill core sections, the ores are grey to reddish in colour, massive and 'metallic' to dark brown and earthy in character, moderately hard and porous (macro and microporous), with variable gangue infill. Ores often appear weathered, typified by ochreous goethite staining and common minor goethite (except in dense core fragments), occasionally exhibiting a more friable texture with coarse magnetite/martite grains. Silicates and lesser carbonate gangue are visible as blue-green to beige to white scaly and/or shaly surface coatings, and finely particulate infill, often goethite stained. Sulfide-rich ore types also occur in part of the deposit, but are restricted to specific drill holes. Magnetite grain size is relatively coarse, compared with magnetite from typical banded iron formations, whereas discrete silicate gangue is mainly bladed/fibrous and/or layered and micaceous in form. XRD analysis indicates the presence of vermiculite, serpentine, stilpnomelane, chlorite, actinolite and clays. There is a spectrum of ore types representing the gradation from 'fresh' (magnetite-dominated) to oxidised and weathered (martite/goethite-dominated). Martite-dominated samples are generally higher in grade, due to leaching and removal of silicate gangue, resulting in higher macroporosity. Where gangue has been leached out, partial replacement by vitreous goethite and/or hydrohaematite is typical, often preserving the fibrous/layered characteristics of the original silicates.

Jan 1, 2009

By M L. Cramer, N P. Wines

"On 9 February 2014, bushfire embers landing on exposed coal in a disused pit at the Hazelwood mine in Victoria’s Latrobe Valley ignited a coal fire that burned for 45 days. The fire was the largest and longest burning mine fire to occur in the Latrobe Valley (Hazelwood Mine Fire Board of Inquiry, 2016). Two Victorian Government Boards of Inquiry have been held into the Hazelwood mine fire. The most recent, in 2015, included consideration of the regulation and implementation of rehabilitation practice at Hazelwood and the other two brown coalmines of the Latrobe Valley (Loy Yang and Yallourn; Government Gazette, 2015).The 2015 Hazelwood Mine Fire Board of Inquiry commissioned Accent Environmental Pty Ltd (Accent) to undertake a review of the financial mechanisms for mine rehabilitation and closure adopted in Australia and overseas (Accent, 2015). Specifically, Accent was engaged to identify ‘any practical, sustainable, efficient and effective alternative mechanisms to ensure rehabilitation of the mines as required by the [Victorian] Mineral Resources (Sustainable Development) Act 1990’ in accordance with Terms of Reference 10 (c) (Government Gazette, 2015).The review by Accent included consideration of a range of financial instruments such as bank guarantees, trust funds and insurance. It considered a number of financial assurance systems in operation in Australia, New Zealand, the European Union, Canada and the United States. These systems included: full and discount financial assurance systems predefined liability proportion systems pooled fund systems the use of post-closure financial mechanisms such as trust funds (Accent, 2015).What lessons can be learnt from other jurisdictions? Are there financial mechanisms already in place that could allow the Victorian Government and the mine operators to manage the risk of rehabilitation default3, lower rehabilitation liability, attain site rehabilitation objectives and allow eventual site relinquishment?CITATION:Cramer, M L and Wines, N P, 2016. Global lessons for a local problem – rehabilitation bonds and Victoria’s Latrobe Valley coalmines, in Proceedings Life-of-Mine 2016 Conference , pp 24–27 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 28, 2016

It is my role at this juncture to report to you on behalf of the Council of Mining and Metallurgical Institutions itself. In essence, the Council is an orbital body - a little like Halley's Comet - it returns to earth, in spectacular style, once in every four years. We must acknowledge, however, that the spectacle is provided by the constituent member body organising the particular event and, on this occasion, it is The Australasian Institute of Mining and Metallurgy. On behalf of the Council and its other constituent bodies may I thank the Australasian Institute most sincerely. Our thanks go to Sir James Foots, the President of the 13th Congress, and to all the members of the organising committee and to the five sub- committees. Over 40 people are involved as full members and I am certain there will have been many more involved in very meaningful ways. None of this great- team would ask me to mention them individually, I'm sure, but to fail to acknowledge the role of John Funnell, the Honorary Secretary, would be an unforgivable omission. We must also thank the kindred institutions in Japan, Korea, Thailand, Malaysia, and Indonesia who all helped with the tours themselves or with the initial preparations. Qantas, Jetabout Australia, and Jetabout Singapore have all also made very important contributions and, in our different ways, we each owe our thanks to them. At the two most recent meetings of the Congress - in Hong Kong and Johannesburg - Professor Marston Fleming made this report on behalf of the Council and was supported on both occasions by Robert MacWilliam as vice- chairman. Marston died in 1983 and Robert died in 1984; both men contributed a great deal to CMMI and we will miss their counsel for a long time. As you know, Sir Alistair Frame succeeded Marston Fleming as chairman in 1984 and I succeeded Robert MacWilliam as Vice-chairman.

Jan 1, 1986

At the outset I want to thank you for inviting a representative of the Chamber of Mines of South Africa to address you on the subject of mining and its future at this, the 13th Congress of the Council of Mining and Metallurgical Institutions. It is indeed a pleasure and an honour to be here. As many of you will recall, four years ago I, as the then President of the South African Institute of Mining and Metallurgy, had the privilege of hosting and welcoming you to the 12th Congress, the third such congress hosted by South Africa. The late Sir Ernest Oppenheimer, President of the 1930 Congress - the first to be held in South Africa - in his opening address foresaw the mining industry as "the most potent factor in spreading the benefits of civilisation over the sub-continent." We have come a long way since those halcyon days but, as I noted four years ago, it still remains true that mines have been, and will continue to be, the missionaries of development in many, if not most, of the Third World countries. I have been asked to address you on the subject of "mining" and to let my imagination roam widely so that delegates can leave the congress with a broader vision than they brought on arrival. It is a tall order and in my attempt to fulfil it I ask you to cast your minds back 120 years to a sultry, rustic day when the first diamond was discovered in South Africa at the now famous town of Kimberley. At that time the South African economy, predominantly pastoral, was still at subsistence level. Almost overnight the ensuing diamond rush turned the then British- owned northern Cape Colony's semi-desert scene into a hive of mining activity, every prospector bent on making his instant fortune. It was very little different, I am sure, to the gold rushes that hit California in 18+8, Australia in 1851, New Zealand in the 1860s. and the Yukon in the 1890s.

Jan 1, 1986

By D Mather

The Resources Boom of the 1960s in Australia provided a strong foundation for AustraliaÆs economic prosperity for the remainder of the twentieth century. In combination with sound economic management, our world-class minerals and energy sector has played a key role in the nationÆs competitiveness, and it has been the major source of our exports since the early 1970s. Even with the emergence since 1990 of major mineral provinces in Latin America and elsewhere, Australia has increased its percentage of world production of several minerals. Between 1990 and 2002, our share of iron ore production rose from 13 per cent to 20 per cent, nickel mine production from eight per cent to 17 per cent, copper mine production from four per cent to seven per cent and zinc mine production from 13 per cent to 17 per cent. Whether this situation will continue during the coming decades motivates the discussion of this reflective paper. The approach is to consider fundamental supply-side and demand-side issues in arriving at a view about the state of the world, the world minerals sector and the Australian resources sector in the coming decades. The argument draws from the experiences of other mature mineral producing countries such as Canada and the United States. In such nations, efficient producers have often sustained competitiveness for extended periods, despite falling grades and other challenging operating conditions. Yet several forces are changing the economic geography of the minerals industry in significant ways. These include the re-emergence of major global mining corporations, the revision of mineral policy in over 100 nations since 1985, the mobility of technology and more efficient transport both for mineral productions and mining professionals. Given these trends the paper argues that the Australian mining industry must continue to change and evolve significantly in the foreseeable future. Its leaders will need to be even more internationally focused if it is to maintain its strong competitive position.

Jan 1, 2006