Search Documents

In southeastern China, offshore Tertiarybasins are buried underneath the broad continental shelf areas from Taiwan to Hainan Island. These basins bear relatively similar characteristics of structure, stratigraphy and tectonics. Based on age and tectonic framework, these Tertiary basins are divided into two groups of Paleogene basin and Neogene basin (Fig.1 and 2). However, observations of extensional structures indicate that the Paleogene basins are rift basins; and the predominant structural features are NE-SW trending half grabens and fault blocks. In a regional scale, these half grabens and adjacent uplifts represent a horst-and-graben structural style. Neogene basins are downwarp basins lying on the tilting continental shelf. Late Tertiary sequences are relatively undeformed but locally with minor folding and thrusting during the Pliocene-Pleistocene.Seismic stratigraphy and well data indicate that the Early Tertiary strata are commonly tilted and disturbed as nonmarine to marginal marine facies deposited in the wedge-shaped half grabens; the Late Tertiary strata are generally parallel undisturbed marine facies accumulated in the enlarged downwarp basins overlying the infilled half grabens. In general, three major regional unconformities formed during the Late Cretaceous, the Late Eocene and the Middle Miocene. Widespread extrusive basaltic flows are commonly associated with these unconformities.

Jan 1, 1990

By Boyle L. A

A positive displacement pump is being dev eloped for pipeline transportation of coking coal to a -50 mm export specification, at a con- centration and velocity which will allow trans- portation in the plug flow region, minimising degradation of the particle structure, and pipe= line friction losses which will be lower than with turbulent or laminar flow. Pump operation is by hydraulic powered free pistons in a rota- ting cylinder block, with cylinders overlapped by stationary inlet and discharge ports in a water lubricated and sealed rotary valve. Before this development coking coal was not considered suitable for transportation in slurry form, for the valves in the double act- ing duplex piston pumps used for slurry pipe- lines, cannot be divorced from the slurry and require that the solid material must be reduced to a fines'consistency before introduction into the pump suction. The hydraulic transportation of 10 million tonnes of -50 mm coking coal, 50 km from the Bargo area west of the escarpment to an offshore shiploader at Port Kembla is feasible. Study shows that economic factors alone would dictate that the development of a pumping system for long distance transportation of coking coal is necessary. The greatest impact from the slurry transportation of coking coal would be the

Jan 1, 1976

Routine, in-pit geological mapping of highwall at Central Queensland Coal Associates (C.O.C.A.) deep strip mines has proved too slow for the increasingly greater highwall lengths which require mapping. This realiz- ation has encouraged the search for faster mapping methods and after trial of ground photographic methods has resulted in the adoption of interpretive mapping off stereo cover, oblique -- aerial photography. This entails using a Cessna 182 light aircraft flying at its slowest speed, the aerial meth- od finally employed consisting of two Vinten, air reconnaissance cameras mounted in parallel and simultaneously taking both colour and black and white photographs of the mine high- wall. The respective 1:500 scale enlargements produced from the 70mm format films combine to present the sharpest resolution attainable under the field conditions pertaining and such information on weathered material as only colour photography can fully render. Total costs for the aerial photography method are estimated to be about the same as those for conventional in-pit mapping. Whilst total costs are comparable, geo- logist's time for mapping a 10 km. length is reduced to less than half that for in-pit mapping (for Stage 1, fully accurate mapping) and accuracy and detail are greatly improved. A permanent, accurate record of overburden

Jan 1, 1981

This paper examines the latest advances in mine drive and motor systems. In the last decade, the drive technology employed for large mine winders has migrated from the traditional dc technology to ac motors with cyclo convertor drives. Recent advances in pulse width modulation (PWM) drives have resulted in these being applied to large winder drives. While having many advantages for the winder system, the PWM drive must be carefully designed to ensure long-term reliable operation. When combined with induction motor technology, the PWM drive presents the ideal solution for winder drives. This paper examines the factors in choosing a suitable PWM drive for a winder installation. Factors under consideration include: winder duty cycle, drive rating restrictions, choice of power semiconductor device, cooling, and low speed operation.The cage induction motor is the motor of choice for large winder drives and has a number of advantages over the synchronous motor. The induction motor is ideally suited to integrated winder applications where the motor is built inside the friction drum, as installed at WMCÆs Olympic Dam site. The challenges of integrating the induction motor into the friction drum will be detailed, including: assembly, ventilation, air gap adjustment, and position sensors.

Jan 1, 2005

By Oxenford R. J

An important rutile-ilmenite-zircon bearing sand deposit was discovered by local farmers at Eneabba, 300 km by road north of Perth in 1970. These heavy minerals occur in a series of ancient strandlines and associated dunal deposits at elevations from 85 m to 170 m above the present sea level and are situated,30 km inland. The strandlines were deposited on wave- cut platforms in an ancient bay bounded by Mesozoic sediments during a series of regress- ions from a high sea level, probably during late Tertiary or early Pleistocene times. The immediate source of the heavy minerals in the Eneabba deposit is a widespread low content of those minerals in the nearby Mesozoic sedi- ments. The high-grade southern portion of the Eneabba deposit has been closely drilled and is now being prepared for production by Allied Eneabba.Pty. Ltd., a subsidiary of Allied Minerals N.L. This part of the deposit is 11 km long and up to 2.5 km wide. It is characterised by little or no overburden and the average depth of mineralisation, bounded by a 2.5 per cent heavy mineral cut-off, is 12 m. The water-laid strandline deposits at the base of the mineralisation are generally high grade, ranging from 20 to 60 per cent

Jan 1, 1973

By Artmont G. J, Palmer K

Alluvial gold is an ideal exploration tracer to bedrock source and indicator of bedrock mineralisation style because (i) gold occurs in a wide range of deposit types, (ii) primary composition is sensitive to style of mineralisation, and (iii) it is a heavy resistate mineral that is readily preserved and easily sampled. In regional exploration of the Central Ranges of Irian Jaya, alluvial gold mineralogy has been applied to maximise the information return from panned concentrate sampling and to focus exploration effort. Primary gold is a solid solution of Au+Ag¦Cu¦Hg, ¦ trace Pd, Te, and Sb. In general Ag¦Hg increase and Cu decreases with inferred decreasing temperature of formation, and gold from particular mineralisation styles has signature compositions that can be used as indicators of bedrock mineralisation type. Furthermore, the abundance of alluvial gold is an indicator of the economic potential of a catchment. The convergent continental-oceanic plate geology of the Central Ranges is conducive to a wide range of mineralisation styles. Mineralogy of gold in ophiolite, skarn, porphyry, mesothermal vein and possible VHMS environments is characterised from alluvial and bedrock samples, and the use of gold mineralogy in prospecting at regional scale through prospect definition to drilling is demonstrated.

Jan 1, 1995

By Evans A. F

Arising out of the increasing demands for efficiency in modern ore-dressing operations has grown a requirement for fuller knowledge of the characteristics of the ore treated. In part, this is being met by improved methods of study of the mode of occurrence of the constituent minerals, and of the intricacies of their physical relationships.A typical instance of the need for such a study is the presence of some undesired mineral in a flotation concentrate or tailing, which may be due either to mechanical association through insufficient grinding, or to incomplete separation in the flotation operation.Again, with modern practice in fine grinding, which often requires that from 70% upwards of the ground ore shall pass a 200-mesh screen, it is obviously impossible to obtain data on comparative grinding efficiencies, for instance, unless there is adequate knowledge of the size-composition of the material passing the finest available screen.Studies like these can be made satisfactorily only after size-separation (which may be carried out conveniently by elutriation) and by actual visual examination with the aid of a microscope, and the minute size of the mineral grains to be examined has necessitated the development of a new technique of sizing and microscopic examination.

Jan 1, 1932

By Keyte SG

Gravity methods of recovering alluvial gold are not very efficient at particle sizes below about 0.1mm. Whereas such gold may not have been economic to recover in the past, the same may not be true today. Centrifugal concentrators, like the Knudsen and Knelson bowls, are showing promise after an inauspicious start, at least in New Zealand. The large proportion of heavy mineral in many auriferous beach sands and the natural hydrophobicity of fine gold should make flotation an attractive contender for its recovery. The conventional mechanical flotation cell is effective, but roughing, scavenging and cleaning are necessary to achieve both high recovery and low mass yield. More problematic is the difficulty of maintaining coarse and dense sands in suspension. The air sparged hydrocyclone is effective at recovering fine gold from a fine Colarado River sand, but is not effective for the coarse and dense beach sands of New Zealand. The flotation column shows much promise for these sands, when recoveries of over 80% and mass yields of less than 1% can be achieved in a single pass. The froth separator of the USSR and flash flotation could also be worthy contenders. It is felt that flotation could be limited to naturally and artificially de-slimed concentrates.

Jan 1, 1990

By Pietrobon M. C, Ralston J, Smart St C R

In an on-going study of the chemistry of base metal sulphide flotation, the effect of the inclusion of cyanide in the reagents suite has been studied, with special reference to ore from Pasminco Mining's Elura mine. Cyanide has been variously described as an iron sulphide depressant, a preventor of sphalerite activation and as an activator of galena. In the case described here, the cyanide appeared to act as an enhancer of the galena flotation performance, raising the lead recoveries by 25 per cent but leaving the sphalerite and pyrite responses unaffected. The lead rougher flotation performance with and without cyanide was investigated over a wide range of redox potentials (0 mV to 400 mV SHE). In all cases, the inclusion of the cyanide brought about an increase in the galena recovery and was responsible for a faster rate of galena flotation during the initial stages of the beneficiation. A surface characterisation study (XPS) of the lead flotation stage, with and without cyanide, indicated that the reagent interacted specifically with the galena and pyrite minerals. It was possible to correlate the surface absorption of the cyanide on the lead and iron sulphides with improvements to the flotation performance using the combination of surface spectroscopy and laboratory flotation Testwork.

Jan 1, 1991

By Robinson WB

An accurate and rapid assessment of coal resources, such as that provided by computer modelling, forms an intergral role in evaluating CSR's coal deposits for future development. An in-house system utilising a number of geological, engineering, costing and financial evaluation routines has been developed for DEC VAX computers. The system is currently being upgraded and enhanced to meet the demands at the various mine sites. Computer modelling of the geology is performed on encoded drillhole information and coal core chemical and physical analyses. A conceptual mine plan is formulated then digitized and superimposed on the geological model. Insitu and product coal reserves and qualities as well as overburden and parting quantities are then calculated for each strip or block. These strip parameters are then transferred to the mine scheduling routines to determine the most efficient mining sequence for the mine plan. Cost factors and scheduling data for equipment specified in the conceptual mine plan are used in the mine costing subsystem. The financial subsystem then evaluates the likely return on investment. Future enhancements to the system include improvements in the response time through the introduction of interactive graphics, the direct interfacing of geophysical and analytical data, and further development of a geotechnical'database.

Jan 1, 1983

This paper investigates dry drilling as a feasible alternative to meet current requirements for improvements in mining productivity in an increasingly competitive world.A field test program was conducted in the surface facilities of a hard rock mine in Sudbury, Canada, to investigate the potential use of dry drilling in underground bulk mining as a conceivably faster and more economical method than wet drilling. The test work consisted of the monitoring of advance rates and bit life while a series of 165 mm diameter holes, wet and dry, were drilled with compressed air at both mine (0.69 MPa) and high (1.72 MPa) pressure levels. The results indicate that penetration rates can be increased by approximately 24 per cent by drilling dry with high air pressure and by approximately 27 per cent by drilling dry with mine air as compared with wet drilling under the same conditions. Dry drilling also has the effect of increasing bit life by up to 69 per cent. An economic analysis for typical hard rock mines indicated that drilling productivity and cost savings can be increased by approximately 23 per cent when dry drilling is utilised.The testing program indicates that dry drilling has the potential to become a feasible technique with regard to performance, productivity and costs.

Jan 1, 1991

The Hunter Valley Rail Project (HVRP) represents most of the coal producers using the Hunter Valley Rail System in NSW to haul coal to the port of Newcastle. This system carries over 70 per cent of NSW's coal exports, comprising over 30 per cent of total Australian coal exports. Hunter Valley coal is the largest export industry in NSW, and one of its largest export growth opportunities. However, the industry is under intense pressure in international markets from existing and new coal producers and from other energy sources. Whilst potential growth in demand is substantial, particularly for thermal coal in Asia, excess world supply has pushed prices down, and this underlying trend may well continue. The industry has lost international competitiveness and as a result, investment has dropped 44 per cent over the last two years. The industry must be rapidly structured to compete and attract investment on the basis that these pressures will continue. Substantial productivity improvement and cost reductions must be made for the industry to regain competitiveness, otherwise growth will not occur and the industry will decline, with serious implications for the Australian and NSW communities. The introduction of internationally competitive rail freight rates is an urgent and essential part of this process. It is the key objective of the HVRP.

Jan 1, 1995

Intensive exploration for iron ore in the banded iron-formations (BIF) of the Pilbara region of Western Australia began in the early sixties and almost immediately established the Hamersley area as a major iron province. The early genetic models for the BIF-hosted ores were based mainly on macroscopic examinations of ores from the "hardcap" zone, and generally accepted a direct relationship with weathering effects on a Mesozoic to Tertiary land surface. Brandt (1964) was the first to suggest a difference in age between the high-grade hematite ores and the more common hematite-goethite types. He initially accepted a supergene origin for both, but later opted for a hydrothermal origin for the hematite ores. Apart from MacLeod (1966), the published views of the next decade reflect a largely parochial interpretation of individual ore bodies, centred mainly on supergene models but with some support for hydrothermal concepts. Except for Ayres (1971), none of the models were backed by detailed mineragraphic data. In 1976, an AMIRA-sponsored CSIRO group began a Province-wide investigation of the wide variety of ore types and BIF, with emphasis on geochemical and textural studies. The resulting conceptual model for a world-wide unified supergene and supergene-metamorphic hypothesis is generally accepted in the Hamersleys.

Jan 1, 1986

By Billington WG

A structural study of northwest Fergusson Island, part of the D'Entrecasteaux Group, was undertaken using colour and monochrome aerial photography and Landsat imagery. The resulting interpretation shows an upstanding, in part, dome-like metamorphic core complex, which is bound on three sides by an en echelon series of low-angle, thrust faults. Faceted gneissic layers occur throughout the complex. These facets are triangular in plan view and range in size from a few tens of metres, to massive composite zones which traverse the entire uplifted zone, The lower surface of each of the facets are, in fact, low-angle decollements which, during uplift, slid one upon the other to accommodate the vertical and extensional movements. As a consequence, deep structural valleys developed which widen towards the zone of maximum uplift. In many places, recognisable topographic features are replicated on both sides of these valleys, and under the stereoscope can be visually reconstructed to their original pre break-up positions. The southern margin of the core complex is less dome-like and falls away, via a series of deeply-entrenched structural valleys, towards a volcano-studded lowland. The lowland appears to belong to a rift or arm, stemming from the more southerly located Goodenough Bay Infrabasin.

Jan 1, 1987

By Hayward SB

The Maragorik prospect is an example of high sulphidation, Cu/Au mineralisation occurring at a high level in the hydrothermal system. As extensive ash deposits blanket the region, controlled-source audio magneto-tellurics (CSAMT), in conjunct-ion with bulldozer trenching, have been used to delineate subsurface geology. Fluid upflow has occurred along EW structures dilated by rotation on the bounding major NW lineaments. Rising hydrothermal fluids have exploited permeable horizons in contact with the upflow structures. This lithological control is evident as ledges of silicification and peripheral clay alteration, at high levels in the system. As is typical of high sulphidation systems, a two phase fluid consists of an initial rapidly moving vapour-dominated phase, followed by a liquid-dominated phase. Much of the zoned and overprinted silica to clay alteration is developed from the vapour-dominated fluid. Mineral deposition occurs as a result of brecciation of the competent silic-ification by liquid phase fluids. Such mineralisation is of restricted volume in ledges proximal to the feeder structures.The style of alteration and mineralisation are indicative of a very low temperature and hence a high level system. Thus, although high sulphid-ation systems are inferred to develop from porphyry-related magmatic fluids, such a source at Maragorik is interpreted to be very deeply buried.

Jan 1, 1994

By Zhen Y. Y, Cook A, Jell J. S, Fleming P. J G

Remapping of the Burdekin Basin has resulted in subdivision of the three interfingering basin-wide megafacies previously recognised in the Early to Middle Devonian Fanning River Group. Eleven carbonate and siliciclastic facies are now identified within the three megafacies, representing coastal plain, shoreline, nearshore, and shallow marine shelf depositional environments. The facies reflect two phases of a major transgression. An initial phase, in the Early Devonian, was confined to the far north of the basin, whereas a second, main phase, resulted in the encroachment of the sea from the east or southeast in the Middle Devonian.The proposed depositional model begins with the drowning of a coastal plain and the transgression of shoreline and nearshore facies between granitic and metamorphic headlands and/or islands. This was followed by the deposition of a patch reef and fringing reef complex including stromatoporoid and coral bioherms, biostromes, and oncolitic, crinoidal, and brachiopod-dominated banks/shoals, together with foreslopes and submarine channels, carbonate rubble deposits and terrigenous sediments. Sedimentation during the peak of the transgression was dominated by sheltered carbonate shelf facies, the maximum, flooding surface being recognisable across most of the Burdekin Basin. Progradation of muddy and sandy nearshore bay and shoreline facies soon followed, terminating carbonate deposition.

Jan 1, 1990

MOUNT STEWART is situated half a mile south of Leadville railway station, which is distant 240 miles by rail from Sydney via Mudgee. It forms a low ridge from which rock waste and alluvium slope gradually to the black-soil flats of the Coolaburragundy River. The Mt. Stewart mine comprises:(a) The Mt. Stewart workings in M.L. 44, parish Talbragar, Co. Bligh.(b) The Grosvenor workings in M.Ls. 44 and 45, parish Talbragar, Co. Bligh.(c) The Extended workings in M.L. 44, parish Talbragar, Co. Bligh.The workings contain 1375 ft.. of vertical shafts, 1105 ft. of underlay shafts, 800 ft. of rises and winzes, 8520 ft. of drives and crosscuts, and 18,000 ft. of stapes.The mine was first opened in 1888 as a silver-lead mine, and a waterjacketed furnace was erected during 18B2. The furnace was installed with two internally-fired tubular boilers of 35 h.p. and 25 h.p. respectively, and two Baker's rotary pressure blowers. The results of the smelting campaign indicate that, during 14 months, a total of 15,000 tons of ore were treated, yielding silver and lead. In addition to this, a quantity of matte was sold containing about 8000 oz. of silver. As a result of the treatment...

Jan 1, 1925

By Scherbatsky VB, zon BM, Babushkin NM, Kitaev BI, Shabel&apos

The structure and hydrodynamics of the raceway zone of a blast furnace was studied on a cold model representing a sector containing two tuyeres. The model differed from the usual in that it was prov- ided with continuous flow of the coke layer at pre- determined rates, had provision for changing the tuyere parameters (diameter, protrusion, inclinat- ion) and irrigation of the layer with liquid. A combination probe was developed which per- mitted simultaneous measurement of the pressure field both across the area and through the height of the layer as well as determining the topography of the raceway. The velocity fields in the layer were measured with a specially made impulse thermo- anemometer. The determining criteria of the model were taken as the relationships between the energy of the blast and the particles, the dimensions of the raceway and the cross-section of the tuyere. The model established the effects of the tuy- ere structural parameters, blast parameters and amount of liquid products of smelting on the con- figuration of the raceway, the structure of the layer, pressure and velocity fields in the vicinity of the tuyeres and in the vertical direction through the layer. The properties of the raceway formation and the structure of the layer in motion have been clarified.

Jan 1, 1981

By Giuli M, Barnaba P, Sacerdote R, Tammaro F

Following a theoretical consideration of the effect of flooding, fluidisation and softening on blast furnace blowing limits, results are presented which show the effect of these parameters on operation. Industrial trials on Oscar Sinigaglia No. 4 BF are reported and results compared with those obtained theoretically and in the laboratory. It is shown that in these trials the furnace operated at levels of fluidisation very much (80-90%) below those theoretically calculated whereas in some cases (high proportion of sinter) actual hot metal output was near the calculated flooding limit. However, it was observed that as the sinter percentage decreases also actual productivity becomes lower than the one caused by flooding. This gap, which increases as other ferrous components (essentially acidic) replace the basic sinter was explained by the softening of the burden under bosh conditions. Softening indices measured on the individual materials yield support to this explanation. Coke rates data show that for approximately every one percent increase in the basic sinter in place of blended sized ore, a coke rate decrease of 1.1 kg/thm results. For acidic pellets this value is 0.6 kg/thm. Results of breakdown and reduction characteristics are also given and their indices compared with actual pt oduction. Measures to improve operations are proposed.

Jan 1, 1975

The Hall-Hoult process is likely to be the dominant method of aluminium production for the remainder of the century. The characteristics of the operation of a modern smelter are described and attention drawn to their disabilities which are due chiefly to the small production capacity of individual cells.The principal components of the Hall-H6roult cell - the electrolyte, the anode and the cathode - are discussed in order to identify the problems of scale-up. The factors influencing current efficiency and energy consumption are analysed and lead to the conclusion that the greatest potential for energy saving lies in reducing the anode to cathode distance (ACD).The most promising direction for major change is in the application of a new titanium diboride - carbon composite for coating of the surface of the cathode carbon. It improves the wetting of the carbon by aluminium and should permit the use of sloping cathodes and anodes. The deep metal pad would thereby be eliminated and, in the absence of magnetic perturbations, the ACD could be substantially decreased.The construction and testing of a full-size "Low Energy Cell" is scheduled for early 1986 and is expected to reduce energy consumption in aluminium production by about 15%.

Jan 1, 1985