Search Documents

Open pit mining at Bingham Canyon commenced in 1904 and about two billion tonnes of ore have been extracted since then. There remain just under one billion tonnes of ore in the pit and this will be mined by 2015. Because the porphyry system extends below the ultimate pit limits, Kennecott Utah Copper Corporation initiated a study in 1997 to determine the viability of underground mining. The study was initiated at that time because the results were to be used to compare the economics of a further pit expansion to that of an underground mine. If a pit expansion was viable then overburden removal would have to start in the near future. This paper is a summary of the work that was carried out for the underground study. Block cave mining was determined to be the most appropriate method to mine the deposit. Two block cave areas have been planned with a total production rate of 72 500 tpd. Additional sources of ore will come from skarn orebodies that are associated with the porphyry deposit. The geology of the deposits is described together with the geotechnical techniques that were used to characterise the rock in the absence of more detailed data that are normally available. A general description of the mine plan is given along with the reasons for selecting the particular methodology used. The study was completed at the end of 1998 and demonstrated the viability of underground mining at Bingham Canyon. Funds have been approved for further drilling and technical studies, which will lead up to a feasibility study in 2004/5.

Jan 1, 2000

By B J. Hutchison, S Gannon, J Chambers, D Oko-oboh

The Kanmantoo copper mine is located in the Adelaide Hills area of South Australia and is owned and operated by Hillgrove Resources (HGO). The mine is a drill and blast, truck and shovel operation mining sulfide (chalcopyrite) ore located in chloritised andalusite biotite schist. The initial Kanmantoo open pit operation occurred in the 1970s, before falling copper prices closed the mine. In 2010 the mine was reopened by HGO and the Kavanagh cutback of the Kanmantoo pit was undertaken. The Spitfire, Nugent and Emily Star satellite pits were also mined through to 2015 before the latest steep wall Giant pit design was developed to take mining out to 2019.There are no major fault structures and only two significant shear zone structures exposed in the open pit walls. The main Garnet Andalusite Biotite Schist (GABS) unit is quite competent so the pit designs have therefore mainly been controlled by four distinct joint sets. This paper is a case study on the influence of the joint regime on the wall stability of the main GABS unit and how a better understanding of the joint regime and the use of rock reinforcement has allowed the steep wall design to be adopted.The paper also describes the remote geotechnical mapping and slope monitoring techniques used to manage the rockfall risks associated with the steep walled slope design.CITATION:Hutchison, B J, Chambers, J, Gannon, S and Oko-oboh, D, 2017. Case study of joint structure and the design and performance of open pit walls at the Kanmantoo copper mine, in Proceedings Tenth International Mining Geology Conference 2017, pp 355–364 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By M Yahyaei, F Reyes, R Lage, V Jokovic

Equipment wear is strongly related to the performance of grinding circuits. In particular, SAG mills are subjected to the wear of their shell liners and grates. Changes in lifter height and face angle impact mill performance, while classification at the mill discharge is also affected as grates wear out. Moreover, liner mass loss caused by wear affects how operators interpret readings of sensors such as load cells or bearings pressure. Automating and optimising grinding circuits under these constrain becomes challenging due to the nonlinear and dynamic nature of the system. The operation of SAG mill grinding circuits remains largely dependent on human intervention, which frequently results in inconsistencies in performance across shifts, reflecting the operator’s personal preferences, experience, and other human factors. The influence of human factors can be reduced by careful training of operators as well as by automation using advanced supervisory control. The latter approaches could benefit from the development of dynamic process models that consider the effects of wear on the performance of equipment over time. This paper presents detailed industrial data showing the effects of wear on SAG mill performance. Additionally, a dynamic SAG mill model that accounts for these phenomena is proposed and demonstrated in a simulated environment. This model is shown to mimic the effect of wear on the performance of industrial scale mills and the operational constraints they are subject to, thus extending traditional SAG mill models. Incorporating wear into modelling and simulation platforms can improve the understanding of the effects that wear can have on the performance of key assets in comminution circuits and may allow the development of more robust model-based advanced process control strategies.

Aug 24, 2022

By H Y. Niu

The coal left in the goaf is easily submerged by groundwater damage. During the mining process of the underlying coal seam, it is necessary to drain the water in the overlying goaf. The coal sample is prone to spontaneous combustion after being soaked in water and air-dried. To explore the effect of micro-functional group transformation of water-immersed coal samples on the spontaneous combustion characteristics of coal samples during the low-temperature oxidation process. Using the experimental method of infrared spectroscopy, the migration law of special functional groups under different oxygen concentrations of water-soaked coal samples was analysed. By means of thermal analysis, the endothermic and exothermic properties of the functional groups in the water-soaked coal samples were studied. The results show that: the higher the oxygen concentration, the more oxygen-containing functional groups in the water-soaked coal sample, compared with the 18 per cent oxygen concentration, the 14 per cent oxygen concentration has a small increase, and the chain length is shortened. The temperature increase together with the oxygen concentration content determines the functional group content, the pyrolysis process produces some functional groups. The lower the oxygen concentration, endothermic rate decreases and endothermic temperature increases, the higher the ignition temperature of coal oxy-combustion, the lower the total heat release, the higher the burnout temperature, and the faster the oxygen-absorbing weight gain and the conversion of functional groups. Below 14 per cent oxygen concentration, the oxidative combustion process will be greatly reduced. The results provide a theoretical basis for preventing long-term water-soaked coal body oxidative spontaneous combustion in shallow buried coal seams.

Oct 12, 2022

By G Hart

As the iron ore/magnetite boom gains momentum, it is particularly important to question established past trends and explore the potential of alternative design options. Traditionally, ‘rule of thumb’ methods have been used to size dewatering equipment. Greater consideration needs to be given to technological advancements and specific throughput testing of each ore body type based on innovative developments.This paper will describe how an innovative approach resulted not only in significant savings in capital cost and site work hours but also delivered a truly optimised design for the thickener duty at Karara. Test work also played a crucial role and a comprehensive test work program on the ore samples showed the scale-up benefi ts of new technology in thickener designs. Working closely with the Karara team during the laboratory testing proved the old sizing theories for iron ore/magnetite processing have been superseded with the knowledge and results of the industry’s newest feedwell technology. Increased solids flux and rise rates in the testing process proved very successful, resulting in signifi cantly reduced thickener sizes and lower capital expense.Mechanical design considerations such as removal of underflow and pump access led to a preference for an above-ground thickener confi guration, and the economics of a completefabrication and installation package favoured steel construction for the thickener units.The ultimate choice of the bolted/fl anged tank methodology provides both economic and timely solutions for the site installation including reduced man power and quick and safe site-work. A benefits comparison between this design and other fabrication and installation procedures will also be analysed in the paper.

Jul 11, 2011

By G W. Swana

Elastoplastic parameter is a parameter that describe how much materials behave elastically up to certain stress states and plastically thereafter (Hudson and Harrison, 1997). In the continuum analysis, two main parameters of the elastoplastic parameter are modulus elasticity and Poisson’s ratio. In the slope, elastoplastic parameter holds the main role for stability related to deformation in ductile type of rock. There’s a limitation to determine elastic or plastic deformation at the field for ductile rock type. Field manifestation commonly showed that there was no accumulation zone during and after the sliding failure mechanism, in other hand, at the research area, manifestation of deformation at the toe of slope only indicated by bulging shape. This paper will focus at the sliding failure occurred at Coal mining Pit Y owned by Arutmin Indonesia, which according to failure investigation report similar with the condition described above. This paper also will be based on two hypotheses, first hypothesis is claystone rock mass has not been reached plastic deformation yet and the second hypothesis is there is a chance that elastoplastic parameter of the rock mass has been changed during the deformation/sliding failure process. Research method of this paper are back analysis using probabilistic analysis in Finite Element Method (FEM), which conducted before and after failure. Then, the result of the displacement or deformation of the analysis will be checked with the actual deformation shape. Meanwhile, the change of the elastoplastic parameter will be analysed and interpreted. This paper hopefully able to be developed to study about elastoplastic behaviour of rock mass in actual condition and the influence of another uncertainty factor which determine the slope stability.

Nov 29, 2022

By R Russell

The relative infrequency of fatalities and other serious events can give them an appearance of being random, of being beyond any reasonable degree of anticipation and prevention. In fact, the vast majority of these events result from exposures that are identifiable, measurable, and manageable. The lessons of prominent incidents, such as the Space Shuttle Columbia, OxyÆs Piper Alpha, Esso Longford, BP Texas City, Massey Mine, as well as lessons from single fatality events, is that alongside the proximate causes of each incident, there also coexisted an underlying fabric of systems, mechanisms, and culture that allowed risk in the workplace to persist and often to become normalised. All of these ingredients of the organisationÆs safety fabric lend themselves to the influence and intervention of senior leaders. The difficulty is that traditional injury prevention paradigms are not sufficient for addressing the precursors that lead up to catastrophic and fatal events. A recent study of such events, led by Dr Thomas Krause concluded that the descriptive aspect of HeinrichÆs safety triangle is useful, but that the predictive aspect is not. The study surfaced reasons why a reduction in less serious injuries does not necessarily correspond to a proportionate reduction in catastrophic and fatal risks. This presentation expands on the findings to include the concept of exposure to the event potential linked to precursor events and the framework for leading an organisation to be both cognisant and effective in eliminating such events.CITATION:Russell, R, 2012. Shifting the cultural paradigm for the prevention of catastrophic and fatal events, in Proceedings International Mine Management 2012, pp 91-96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By Nikaido M, Kanda Y

A rotary type separator has been developed which separates particles on the basis of their shape. This separator was applied to a particle size range of about 50 - 120 ¦m, and to our present knowledge may be the smallest size range ever to be separated. A theory of the separation is given based on the difference of an adhesive force of the particles: the adhesive force between spherical particles and plate is more powerful than that of irregular shaped particles for the same particle size. These facts have been ascertained by the measurement of an adhesive force by a centrifugal method. US and Japanese patents have been obtained on this separator, which consists of a borosilicate glass cylinder of 150 mm outside diameter, 120 mm in width, and an AC electromagnet. The samples used in this study were mixtures of spherical glass particles and non-spherical shaped glass particles. The results are summarised as follows. In the case of mixtures of spherical particles and irregular shaped particles in the weight ratio of 1:1, the spherical content of the spherical product became 70 per cent - 75 per cent, and in the case of 3:1, the content became 87 per cent - 90 per cent, as the result of one separating operation. However, for a mixture of somewhat rounded particles and irregular shaped particles of weight ratio 1:1, the rounded content varied between 58 per cent - 73 per cent. The feed rate of the particles mixtures was about 0.3 g/min. Newton's Efficiency was 20 per cent - 60 per cent. The separator may find application in shape separation of ceramic powder, metal powder or industrial diamond powder.

Jan 1, 1993

By J White

The Eyre Peninsula (EP) has been known for its iron ore for more than a century. Edward John Eyre noted the ironstone outcrop at what is now Iron Knob in the 19th century. Sir Douglas Mawson visited and reported on the geology of the lower EP in 1906, noting the widespread presence of iron stone and the likelihood of copper being associated with the iron stone. Despite this knowledge there has been only one successful iron ore mining region developed on the EP and that is Iron Knob and the Middleback Ranges which have been mined continuously since 1899. The Middleback Ranges can justly lay claim to be birth place of the Australian iron ore and steel industries.The discovery of large scale haematite resources in Western Australia meant that there was no need to seek out iron ore that needed benefi ciation. The low price of iron ore precluded further development of the EP and many other areas in Australia and overseas. This situation changed rapidly in the mid-2000s with the emergence of China as the world’s industrial power house and the soaring demand and price for many resources including iron ore. This triggered a flurry of activity across Australia and led to the rapid exploration and drives to develop the EP iron ore. A brief examination of the magnetic maps of the EP shows the wide spread presence of magnetite and associated smaller haematite deposits. A closer look reveals the magnetite deposits to vary in formation style and host rock lithology as well as being significantly altered by regional metamorphism. *This is an abstract only. No paper was provided for this abstract.*

Jul 11, 2011

Recent work has shown that, in at least some instances of regional metamorphism, metamorphic diffusion has been restricted to such relatively minute distances (of the order of 1.0 mm and much less), that there is no clear, direct evidence of prograde metamorphic mineral reactions, and that metamorphic equilibrium does not appear to have been attained through even very small domains.A number of stratiform orebodies and their immediate metapelitic environments exhibit very large, seemingly "disequilibrium", assemblages of regional metamorphic index materials. One such, in north-eastern Australia, includes laumontite, prehnite, chamosite, stilpnomelane and related hydrous iron silicates, primary chlorite, sericite-muscovite, epidote, actinolite, biotite, almandine, andradite, metamorphic hornblende and clinopyroxene, scapolite, staurolite and sillimanite, all within a 20 metres length of a single diamond drill core. In this and several related occurrences it appears that metamorphism has involved very small scale in situ transformation of pre-existing materials rather than large-scale diffusion and reaction, and hence that the observed metamorphic minerals have probably been derived directly from precursor materials of sedimentary/diagenetic origin.It is concluded that the fluctuating seafloor interplay between warm, acid, concentrated hydrothermal waters with cold, alkaline, dilute seawater during stratiform ore formation, together with diagenetic processes, leads to the formation of a wide range of clay, chlorite, mixed-layer clay and clay/chlorite, and zeolite precursor materials and hence, later, to the complex assemblages of metamorphic minerals closely associated with some stratiform ores. Commonly included in highly localized assemblages of this kind are various minerals which, in conventional regional metamorphic studies, are generally regarded as indicating widely different grades of metamorphism.

Jan 1, 1982

By A Suokas

Boliden Tara Mines Ltd, located in County Meath Ireland, produce in excess of 2.5 million tonnes per annum of ore from the underground resource located 40 miles north west of Dublin. The zinc-lead ore is mined using long hole open stoping techniques, with ore treated on site. The operation is continually searching for new ways to improve productivities at the mine, and have employed a detailed data acquisition and reporting system on site to provide feedback around performance. One area where both Boliden Tara Mines Ltd and Orica Mining Services believed improvements could be made was in the application of bulk emulsion technology through an Orica supplied but Tara operated Maxipump Delivery System for all production and development blasting at the mine. Both parties committed to the evaluation of this technology at the mine, however the capital cost and technical and economic changes meant the project needed to be diligently investigated and any improvements documented. The first stage of this project was for Orica Mining Services personnel to visit the operation, and conduct a detailed analysis of the operationÆs performance over the past 12 months. The next step in moving forward was then to commission and utilise the customer operated emulsion system at the mine. This was then followed with the collation and analysis of data from the demonstration period to examine and document the benefits of the system. This paper is a summary of the observations made during the site inspection and the data analysed to date, and has been used in determining operational and financial improvements in the comparison between a Maxipump Emulsion Service and the current ANFO loading systems.

Jan 1, 2005

A new lead refinery with a. capacity of 230,000 tons per year com-menced operation at*Port'Plsie in October, 1959. This plant' superseded the refinery which had operated from 1933 with the advent of thecontinuous lead refining process. The incorporation of new equipment following local metallurgical developments, together with the overseas demand for lead of extremely low antimony content, created difficulties in operating the original plant. The new refinery project was under-taken to cover this disability and to gain the full advantage of the new processes.Desilverising and softening are carried out in units identical in size to those used previously. Metallic'zinc is now recovered from the entire output of desilverised bullion by vacuum distillation. Final refining is then carried out by batch'treatinent with caustic soda yield-ing lead of purity previously unattainable at Port Pirie.These two processes have replaced continuous dezincing by oxidation, a high temperature process which caused large quantities of lead and antimony to be recirculated. As the final stage is a .batch process the product composition can be.checked before casting. Individual batches can be adjusted to produce special alloys to,consumer's specification.Improved casting equipment has allowed the quantity production of pigs of good physical characteristics either as 56 lb bars or 2000 lb pigs. This, together with the high purity of the lead, has assured the B.H.A.S. position in world markets.Automatic control systems have been extensively employed particularly on the vacuum dezincing unit.The anticipated financial benefits have been achieved mainly by a reduction in the tonnage of recirculated materials, a smaller labour force, and reduced maintenance requirements.

Jan 1, 1963

By M Pizey

After 60 years of operation, coal extraction at Solid Energy New ZealandÆs (SENZ) Strongman Mine, near Rapahoe is scheduled to end in early 2005. Up until 2003 the closure bond for Strongman Mine was only $930, and both SENZ and the West Coast Regional Council (WCRC) agreed that a more realistic level of bonding was required.   A conceptual closure plan has been developed by Golder Associates, and the cost of the work estimated. Closure includes decommissioning of equipment and facilities, rehabilitation and replanting of all disturbed areas and a period of maintenance and monitoring to verify that closure objectives have been met. Significant maintenance allowances are included to cover management of underground fire, subsidence and slope instability. These make up much of the potential ongoing environmental liability at the Strongman. All costs incurred beyond year 1 of closure are discounted to present value. Uncertainty in costs is addressed by Monte Carlo simulation, with an 80 % confidence level adopted.   A bond quantum of $3.0 million has been calculated for the first year of closure at Strongman. A three-year ærollingÆ bond is proposed. Progress will be reviewed annually, with the bond adjusted up or down accordingly. It is then renewed for a further three years. This allows for progressive return of the bond as rehabilitation objectives are met and verified. Similarly, if there are delays in meeting objectives, a proportion of the bond may need to be kept in place for a longer period than assumed. The level of bonding in place for the Strongman operation at any time in the future will therefore reflect the cost to complete the closure work programme.

Jan 1, 2004

Present value maximisation studies are a useful aid in enhancing the economic performance of open pit mining operations. Maximising present value helps to reduce the risk of financial failure. Maximisation of present value also means that the capital invested is being used most efficiently. A characteristic step in determining the present value of an open pit mining operation is to set out the sequence in which increments of material (ore of various grades and waste rock) are mined. Traditionally, present value maximisation has been performed by selecting a cut-off grade for each increment so as to maximise the present value of the total operation, by an iterative process using computers. Kenneth F Lane has developed a method and applied it to many mining operations. An alternative method for determining the maximum present value of an open pit mining operation is given. In this method the maximum present value is determined by working backwards from the end of the operation life, progressively asking the question of each increment `what cut-off grade maximises the the present value at the start of mining of that increment?' The method allows calculations to be performed by a `spreadsheet' package. Present value determinations are characteristically performed under constant conditions (eg prices, costs) throughout the operation life. Unfortunately real life circumstances are rarely constant, with the costs of mining inputs rising at variable rates. The prices received for mineral products have been shown to broadly trend downwards with time in real terms. Treatment of such changes in the determination of the maximum present value of an operation is discussed.

Jan 1, 1994

Aspects of the formation, decomposition and acid solubility of zinc ferrite were examined to find potential ways of increasing the recovery of zinc from a calcination process of mineral concentrates. Ferrite can begin to form within 2 hours at 450¦C. while complete reaction can occur after 35 minutes at 700¦C. The nature of the starting materials has a pronounced effect on the rate of formation and below 700¦C. ZnSO4 and Fe2O3 proved to be the least reactive of the materials investigated. It is possible that iron in a mineral admixed h sphalerite can be converted to a relatively inactive form, however, it does not seem possible to prevent zince f formation when iron is in the sphalerite lattice. At the two temperatures examined, 650¦C. and 700¦C, the presence of SO2 in the atmosphere accelerate .e formation of ferrite. Prolonged exposure to such atmospheres, however, caused the ferrite to decompose to ZnSO4 and Fe203. The optimum temperature for decomposition was 650¦C. and it was virtually complete within 2 hours in an atmosphere of 10% SO2 in air. Zinc ferrite was also decomposed by CO at low concentrations, and by heating with limestone at 1000¦C. for at least 2 hours. The solubility of zinc ferrite in acid was influenced by the starting materials used. As both the reaction temperature and the time at temperature increased the acid solubility decreased. The acid solubility was a minimum when the ___i_.. n - I -r~...................c -..... F, fe..i+e --A frn... A01- +^ Z(lo/

Jan 1, 1970

By G Harbort, C Sola

The rapid development of geometallurgy in the mining industry has occurred in relatively recent times. Its importance as an independent discipline in the mineral processing world has been emphasised and recognised. To a large degree, this is the result of a growing understanding of the ore type being processed and their application to provide better metallurgical responses in different mineral processing techniques. The development has matured from early progress through to geological knowledge and into the realm of the metallurgist and mining engineer. Working together, they have developed a powerful framework that will interpret a body of mineralisation into measurable properties.The integration of geometallurgy and operations has become of increasingly important due to improvement in understanding of an orebody as a natural system formed by a number of processes and with a definite fabric of mineralisation within different geological domain. These have to be taken into account when creating techniques that will enable operations to extract the valuable components from a distinct type of ore. Incorporation of such knowledge at an early stage of development, such as the feasibility stage significantly reduces the project risk.This paper is written from the unique perspective of a process engineer embedded within a geological team. It discusses issues such cross discipline communications and misconceptions and details the numerous tricks, traps and treasures of geometallurgy encountered during defining of the Seminco and Taysan resources.CITATION:Sola, C and Harbort, G, 2012. Geometallurgy - Tricks, traps and treasures, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 187-196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

An Investigation on the Effect of Chrysotile Particle Shape and Anisotropic Properites on the Rheology of Chrysotile Suspensions Chrysotile, a polymorph of serpentine, is a phyllosilicate mineral that occurs as a major gangue mineral in many ores (eg Mt Keith nickel sulfide ore, Western Australia). The rheological behaviour of chrysotile stems from two main factors: its distinctive morphology and its electrical surface charge. It is believed that these factors are central to the problematic rheological behaviour and low solids throughput typically experienced in the processing of such ores. In this work, a study of the effects of chrysotile surface charge properties and particle shape on the rheology of chrysotile suspensions was conducted. It was found that the rheology of suspensions of pure chrysotile is characterised by extremely high yield stress values over a broad pH range (pH 4 to 11).The disparity in the point of zero charge and range of maximum yield stress for chrysotile is consistent with the anisotropic nature of chrysotile particles. A comparison of the rheological behaviour of quartz suspensions (non-fibrous) to that of chrysotile suspensions (fibrous) provides a practical indication of the effects of the fibrous nature of chrysotile relative to non-fibrous minerals. The long, thin fibres are easily entangled to form suspensions with much higher plastic viscosities and Bingham yield stresses than non-fibrous particles. Chrysotile particle shape and surface charge are central to the rheology of chrysotile suspensions, although shape appears to play a more significant role in this regard. This fundamental study would be beneficial to the ongoing research for improved recovery in the Mt Keith nickel sulfide ore as well as other chrysotile bearing ores.

Sep 13, 2010

By A Creighton, C McKenzie

Blasting is a critical task in the development of an open pit. The formation of stable slopes is also essential to the safe and economic extraction of ore. The objectives of a mine blasting department are often considered to be in direct conflict with those of the geotechnical department. This should not be the case. Personnel in the various mining departments need to understand that their goals are the same û to optimise safety and cost-effectiveness of the operation. Blasting has the potential to damage rock that is to remain in situ by generating either excess vibration, and/or pressure. These damage mechanisms are described and guidelines with respect to blast design to minimise the potential for damage are given. A rock mass could be expected to be subjected to varying degrees of damage by blasting, including both intensity of damage and also the extent of damage. These issues have potential to impact significantly on geotechnical design considerations. It is therefore important for the practitioner to define what constitutes damage. In the context of mining, it is recognised that there is a need to balance the requirements for efficient excavation with those of forming stable and cost-effective pit walls. It is therefore important to have a set of key performance indicators (KPIs) against which the performance can be bench marked. These would include cost and time, both of which may be influenced by very diverse factors such as drilling, explosives and their performance, fragmentation, excavator and haul truck performance, requirements for batter clean-up and safe working practices. KPIs are identified and discussed in this paper.

Jan 1, 2003

THERE is available a considerable amount of literature concerning the practice, and, to a smaller extent, the theory of ventilation as it applies to coal mines. Publications considering the subject of ventilation of metal mines from a practical viewpoint are much less numerous, whilst the treatment of the theoretical aspect of the question (except in so far as is common to coal mining) appears to have been almost neglected. This may be due to one of two causes (a) That in many metal mines (especially those which have not attained a great depth), on account of the greater number of connections with the surface, as compared with coal mines, natural ventilation has sufficed.(b) That in metal mines where the foregoing is not the case the solution of the ventilation problem from theoretical considerations has been regarded as involving so many complications that any attempt at the determination of a set of concrete ventilation figures applying to and throughout the mine would be futile. Whilst it is freely admitted that the difficulties inherent in the application of theory to the ventilation of metal mines are numerous, it must also be admitted that few attempts have been made to overcome them. The ultimate aim, of course, would be the collection of sufficient data to enable the probable behaviour of the air-currents throughout the whole of the workings of any mine to be accurately predicted under any particular set of circumstances. Failing the attainment of this goal of perfection, it would at least appear that much valuable information might be obtained. In ventilation, as in...

Jan 1, 1921

By Edmonds G. A

The power station went into operation in 1931, when the installed capacity was 12,500 kVA. with a loading of 4,000 kVA. In 1936 the loading increased to 6,750 kVA. which necessitated the addition of a third set which went into operation in 1937, the installed capacity at that date being 18,750 kvA. with a loading of 7,000 kVA. This remained fairly constant until 1945, when a gradual increase was noticed, the loading in 1952 being 10,598 kVA.With the addition of the copper plant, additional generating capacity was required and it was decided to raise the installed capacity by the addition of a fourth set to 34,375 kVA. with an expected loading, when producing copper, of 20,000 kViA.MAIN POWER PLANTThis consists of three GiE.e. alternators of 6,250 kVA. or 5,000 kW. at 0.8 P.F. rating and one G.E.C. alternator of 15,625 kVA. or 12,500 kW. at 0.8 P.F. rating, making a total generating capacity of 34,375 kVA.Each alternator is driven by Fraser and Chalmers turbines at 3,000 r.p.m.SYSTEMThe main 3 phase 3 wire 3,300 volt distribution system has the neutral point of alternators earthed through by one or two earthing resistors designed to limit earth fault current to 3,000 amp. for 20 seconds, in the case of the large machine, and to 1,100 amp. for 10 seconds, in the case of the smaller machines, or full load of either size machine at rated voltage.

Jan 1, 1953