Search Documents

Western Mining Corporation began shaft sinking operations at it's Foster orebody, south of Kambalda, on the 20th June, 1984. The top levels of the orebody are currently being mined via a decline some 1.5km away.Long term plans require the shaft and decline to combine and produce 400,000 tonnes of nickel ore per annum. Eventually all of the ore produced will be hauled up the shaft.The shaft is 4.5m in diameter and the target depth is 760m. Ground conditions to date suggest there will be no further need for concrete lining beyond the oxidised zone. As such, the sink is an open-shaft development in competent basalt rock. Shaft furniture will be installed on completion of the excavation to the target depth.This paper summarises the experience in the project to date, along with comparisons to conventional shaft sinking methods employed in previous years at Kambalda Nickel Operations.

Jan 1, 1985

By M Grossi, G Baiden

This paper describes a new mine backfill method based on a newly invented binder with several years of test results from laboratory and onsite applications. The new binder has several advantages over traditional Portland and slag cement binders. One tonne of the new binder can replace two to three tonne of Portland cement when used to consolidate backfill and can result in the same compressive strength within seven days. When comparing backfill slurries of the same pulp density, the new binder attains more volume of in-place backfill mass than Portland cement because of the high crystallisation of water, resulting in tightly filled stopes. The crystallisation of the water provides for less or no dewatering in the backfill stope and easier transportation of the backfill slurry. Pastefill performance can be achieved by using pulp densities typical of a hydraulic backfill and the new binder, all the while transporting with the same ease of hydraulic fill.

Jan 1, 1998

The Mt Leyshon Volcanic Complex lies 24 kilometres south-west of Charters Towers and is part of a major continental volcano-plutonic province of Permo-Carboniferous age in north-east Queensland.The volcanic complex is located on the contact between Cape River Beds of Cambrian age and the Ordovician Ravenswood Granodiorite Complex. The emplacement of the complex appears to have been structurally controlled and is at the intersection of major north-east and minor north-west trending lineaments. The gold mineralisation occurs in the form of cavity coatings, matrix replacement, disseminations, and vein and fracture fillings containing quartz, chlorite, carbonate, pyrite, sphalerite, chalcopyrite and galena in various volcanic breccias and rhyolitic intrusives. The current published mineable ore reserves, calculated by Noranda Australia Limited, are 6.3 million tonnes of 1.8 grams per tonne gold and 4.8 grams per tonne silver. The orebody is open at depth, and in all directions except north where it abuts the granodiorite.

Jan 1, 1986

Maintaining and improving the economics of open pit mining in the future requires understanding of the characteristics of open pit mining that are different to other mining or business activities, designing mines in the first place to be less susceptible to changes in these important characteristics, and adopting strategies which yield reliable returns despite unforeseen change. Planning and production personnel require guidelines and performance standards that are based on sound economics not solely on production criteria. The guidelines adopted for long-term implementation must assume a declining price for mineral products along with declining real costs, with research efforts directed at development of both evolutionary and revolutionary ideas aimed at implementation. Decision-making must focus on risk and probability criteria rather than just simple return-on-investment criteria, and the approach for management of personnel must support the higher level of communication essential for fast decision-making in the new environment of continual change.

Jan 1, 1992

By Cheung L. C C, Maconochie A. P

SIROFRAG is a computer-based imaging system that quantifies the post-blast rock fragment size distribution in a muckpile in a mine environment. Improvements in blast performance and blast modelling are being hampered by a lack of a quick and objective method to evaluate the major result of the blast: the fragment size distribution. This is usually done by hand digitising muckpile photographs: a labour intensive and tedious process. SIROFRAG is being developed to quickly, cheaply and objectively provide this information. SIROFRAG is based on active stereo image analysis. It uses a light stripe to illuminate a muckpile and a pair of video cameras to determine the 3D nature of the scanned objects. The imaging system is based on a novel prototype scanning projector that allows images to he captured in full daylight. The Microsoft Windows based software controls the projector and interprets the captured images to provide a size distribution of exposed rock fragments.

Jan 1, 1995

By R E. Conder

A major initial and ongoing cost component in many mining operations is that of transporting mined materials and processed ore from the point of extraction or processing to the next operation. For various reasons the transport distance can be significant or in some cases the route may be particularly challenging. The trend to higher production rates to gain economy of scale benefits and capitalise on sales opportunities means that optimisation of transport can play a significant part in profitability. Apart from the cost criteria, increasingly there are other criteria such as environmental restraints, land ownership and security of supply that can have a significant impact on determination of the optimum route and transport vehicle. The paper aims to briefly highlight the important selection criteria and the benefits and disadvantages of the most commonly utilised transport vehicles. It then moves on to looking in more depth at belt conveying, highlighting the unique capabilities of the Metso MRC Cable Belt Conveyor system.

Jan 1, 2004

This paper forms part of a series of papers relating to the Melbourne Underground Rail Loop and presented to the Fourth Australian Tunnelling Conference in Melbourne, March 1981. The Design of Electrical and Mechanical Services in Museum Station and adjacent Running Tunnels and their relation to Rail.wruy Operation through the Loop are described. The descriptions, while specific to Muscrio Station, are generally representative of those being provided at Parliament and Flagstaff Stations. The Museum Station comprises some 6500 square metres of platform and track area, 5000 square metres of booking hall concourse and entrances and 1200 square metres of offices and plant rooms. The Mechanical and Ilectrical Services for this complex are .imilar in many aspects to those of a large !.gr.hrise city building, but in general the i::;ign is directed more strongly towards :.arety, durability and reliability, and subject to many restraints imposed by L'mitations of space and accessability.

Jan 1, 1981

The application of modern sciences prior to nineteenseventies have resulted in the placing of Continental Drift theory into broader concept of Plate Tectonics. The concept is applied to explain the Cenozoic Tectonics of North Sumatera.Oceanic crust flooring the Indian Ocean is moving northeasterly and being obliquely subducted at a Benioff zone along the western margin of Asian Plate, marked by the Sunda Trench in the west coast of Sumatera. This phenomenon was generated since late Mesozoic, continued during Cenozoic era up to present day, resulted an exellent example of arc-trench system which can be traced along SW - NE transect of North Sumatera.The oblique-subducting plate of Indian Ocean beneath Asian Plate, together with spreading of Andaman seafloor beginning in Pliocen epoch, have led to the origin of Sumateran Fault System; the System extends throughout the length of Sumatera island. In the region under review it comprises almost contiguous set of broadly SE-trending. Evidences for transcurent-dextral displacement have been observed.

Jan 1, 1990

By Williams ID

Ore and coke of various size fractions (1 to 11 mm) were packed in a column (146 ó) and resistance to air flow measured under a range of conditions. Results have shown that layered charging results in an interface having essentially a directional structure the thickness of which is directly proportional to the coke and ore size ratio and whose flow resistance exceeds that of the coke layer many times its thickness. Friction factor - Reynolds number plots showed large positive departure from the Ergun equation for all components investigated whilst functional analysis and that in terms of bed constants, showed a strong dependency of the pressure gradient on bed properties and the actual particle size as well as the size ratio. It is also shown that pressure gradient in mixed beds follows previously reported behaviour and that a directional interface offers higher resistance to flow than a mixed interface having the same volumetric ore/coke ratio. Significance of results to practice is discussed.

Jan 1, 1975

By Kokubu H, Moro-Oka A

Gaseous desulphurization from hot metal- lurgical slags containing sulphur mainly as sulphide and(or) sulphate was measured under `low at four different oxygen pressures. The total gas rate was from 1.7 to 2,8 litre/min. Crushed slag samples weighing 2 to 12 g were used for the experiments. The amount of SO2 gas evolved from samples kept at 15500 was rieasured over tires ranging from 20 to 300 min. The gaseous desulphurization rate of sul- phide sulphur becomes high as the oxygen part- ial pressure is increased, while that of sul- phate sulphur is high under low oxygen pressure. The effect of basicity on the desulphurization rate of sulphide sulphur in oxygen atmospheres is not obvious in the range of basicity from one to three. Changes in the ratio of sulphide to sulphate sulphur during the run in oxygen axe analysed. Desulphurization reactions and the rate controlling steps are discussed. De- sulphurization phenomena can be explained by inte.-¦ucia.l chemical reaction rate control.

Jan 1, 1980

By Weller KR, Restarick CJ, Stewart PSB

Following a detailed assessment of concen trator performance at Broken Hill South Limited which was reported in a previous paper, the fine grinding section was changed from a parallel arrangement of the two grinding circuits to a series arrangement, and the concentrator per- formance re-assessed. The change to series grinding had virtually no effect on the actual or potential capacity of the circuit to make a final product with 80% passing 100 mesh. However, the fresh flotation feed contained significantly less +150 mesh lead and +65 mesh zinc (material which was shown to float poorly), without an increase in the quantity of poor-floating ultra-fine lead and zinc. From the size-by-size flotation recovery data, it was shown that overall recoveries of both lead and zinc were approximately 1% higher than they would have been without this change in size distribution and it was concluded that this was a direct result of the change in grind- ing procedure.

Jan 1, 1972

The gossan developed from the Whim Creek Cu-Zn-Pb-Ag sulphide deposit, in the Pilbara region of Western Australia, occurs near the top of a ridge in a dissected plateau 01 moderate relief. The gossan is characterized by the abundance of secondary ore minerals which indicates that it is relatively immature, due to climatic conditions and erosional stripping.The abundant presence of secondary carbonates indicates that the low pH generally resulting from sulphide oxidation has been neutralized, probably by the buffering effect of carbonatcs and silicates. Fe, Cu, Pb, 'Ag and Sn have been enriched in the gossan relative to the primary ore, and Mn, Ti, Co and Ni have been strongly depleted; other elements have remained substantially unchanged. The gossan has a strong gcochemical signature characterized by high Cu, Zn, Pb, As, Sb, Sn, Ag and Mo coutents. Boxwork textures are poorly developed, bu't the gossan has other diagnostic mineralogical features including sulphide inclusions in quartz and the presence of residual cassiterite.

Jan 1, 1982

The Fraser Range is composed dominantly of basic pyroxene granulites derived from basalts, many of which appear to have been vesicular and*pillowed. Acidic and basic garnet-bearing granulites are important in the west, and acidic granulites and narrow anortho- site layers are dominant in some regions east of the Fraser Range. An extensive flat-lying olivine gabbro sheet cuts the granulites, and in places has been converted to spinel-bearing meta-gabbros and pyroxene granulites. The granulites of the Fraser Range (Proterozoic) are separated from the gneisses and schists of the Goldfields regions (Archaean) by the Fraser Fault, over which there is a large gravity anomaly (gradient 20 milligals per mile). Some of the problems associated with the concentration of Cu, Ni, etc. liberated from mineral lattices during metamorphism, and other principles of metal concentration in granulite terranes, are discussed. The recognition of vesicular and pillowed zones, even though highly metamorphosed, is of fundamental importance.

Jan 1, 1969

Mining is taking place at increasing depths of cover on the Southern Coalfield beneath pre- dominantly massive sandstone strata. Within the next twenty years, there will be longwall mining at depths greater than 600 m. As the Sydney Metropolitan area continues to expand and as coal mining approaches these urban areas subsidence will continue to become an increas- ingly important aspect of coal mining research. Investigations commenced in the mid 1960's and it is now possible to predict subsidence in the Southern Coalfield with reasonable con- fidence. The work is showing that the characteristics of the subsidence troughs over the deeper mining at Appin differ from the characteristics of mine subsidence at less cover. The longwall mining at Appin Colliery has resulted in a maximum measured subsidence of 730 mm. The maximum strains were small because of the large radii of curvature of the subsidence profiles. There was no damage to any of the buildings in the township of Appin.

Jan 1, 1981

By B Cronin, M Gao, M F. Young

Fine grinding technology has become extremely important for Mount Isa Mines Limited in the last decade for flowsheet development for the McArthur River deposit and in rejuvenating the Lead-Zinc Concentrator at Mount Isa. Regrinding products with 80 per cent passing seven microns and 12 microns were required, respectively, for the McArthur River ore and the Lead-Zinc Concentrator at Mount Isa. Development of the ISAMILL, a horizontal stirred mill with a gross mill volume of 4000 litres (a net volume of 3000 litres), has been successful in delivering the required grinding product sizes with an energy consumption acceptable to a mining operation. The ISAMILL performance for processing both lead and zinc streams at Mount Isa is discussed in this paper, including the milling energy efficiency, the media wear and the size-by-size recovery data for one flotation process following the fine regrinding stage. The potential use of the ISAMILL technology at various phases of the mining cycle is also discussed.

Jan 1, 1998

By Williams M

Sheet flotation is a new two dimensional column flotation cell that produces continuous spectrum of products. Analogous to a shaking table in its performance and analysis, sheet flotation is a sheet of bubbles rising through packing contained between two walls. Feed enters the sheet at the lower left and the product exit along the top and right edges. Iligh grade materials exit at the top left, middlings exit at the top right comer and low grade waste materials exit at the bottom right. As in the case of a shaking table, two motions are required: up and right. Bubbles furnish the upwards movement for hydrophobic particles, slanted packing the rightward movement for hydrophilic particles. The sheet flotation cells is analysed as a 40 x 40 array of simple cells. In practice, 1000 x 1000 arrays of simple cells may be expected. With larger arrays, excellent separations may be expected. Because there is no recycle, there is no build-up of middlings in

Jan 1, 1993

The Iron Prince orebody occurs within the Lower Middleback Jaspilite Horizon of the Middleback Group and consists of hematite within host rocks of jaspilites and schists. The ore was probably the product of leaching of silica from jaspilites and replacement by iron, concentrations occurring in suitable structural traps. The narrowness and the presence of extensive dolerite amphibolite dykes within the orebody make it essential to operate a grade control programme in advance of the faces. Information from drilling is drawn up on bench plans, step plans and impurity overlays, and these serve both in day to day production planning and in long term planning. Mining is done selectively by open-pit methods and blending conducted by keeping at least three faces of different grades of ore open at any one time. No stock piles of ore are kept for blending, but contact ore, contaminated ore and enriched material are dumped for later beneficiation.

Jan 1, 1971

By Edmonds W, Giles C. W, Webb R. J, Gum J. C

Gold production from The Granites - Tanami Goldfield during 1993 is expected to exceed 8 t, eclipsing that of the traditional Northern Territory gold mining districts of Tennant Creek and Pine Creek. This is the result of dedicated and successful exploration, and the consequent discovery of new orebodies such as those at Dead Bullock Soak.Following granting of access to regional exploration areas in 1988 and identification of favourable host rocks in the Schist Hills area, North Flinders Mines (NFM) began a methodical exploration program of detailed geological mapping, rock chip sampling, costeaning and various types of drilling. The first resource of 600 000 t of 3.3 g/t gold was announced in mid-1989. This has grown progressively with systematic exploration to the currently published resource inventory of 6.6 mT @ 5.4 g/t, (as at 31.12.92) contained in six separate orebodies within the Dead Bullock Soak Mineral Lease at Schist Hills.

Jan 1, 1993

By Postupack C

A major problem that has continued to plague the surface and underground coal industries is blast induced damage to the coal seam. Blasting Analysis International, in conjunction with a number of other organizations, has continued to address this concern through 14 years of field research in 68 full-scale production environments worldwide. Compiled results were obtained from varying field conditions. These included single and multiple seam coal mines, horizontal, rolling and steeply dipping coal seams and varied borehole diameters (ranging from 102 to 381 mm) and when using various explosive formulations. Results are discussed in detail along with the tools, test methods and analysis techniques to identify and quantify the problems. Over ten major causes of coal damage were identified. A number of practical and economic recommendations are presented that can benefit the entire coal and blasting industry especially in commercial operations whose economic growth relies heavily upon recovering an undamaged coal seam.

Jan 1, 1995

By Moffatt G

Approval to operate Longwall No. 7 at Appin Colliery in 1979 was granted pursuant not only to the usual statutory provisions, but also that an adequate means of drainage of methane gas be incorporated. A methane drainage plant was subsequently designed and constructed some two km from the pit top at the site of the Colliery main upcast and down cast shafts. Modern plants of this nature are completely automated using programmable controllers and computers to provide control and management reporting functions. Complex mechanical systems are installed to extract the gas and in handling and storage processes. Gas utilisation plants exist which can generate power from methane. These plants are further enhanced by harnessing waste heat produced in the generation process. The installation, automation control and monitoring of these plants incorporates many facets of engineering from high voltage power supply and computer technology to complex gas handling procedures used in gas compression storage.and generation of electric power.

Jan 1, 1982