Search Documents

By McPherson M. J

An experimental investigation was carried out to determine the various gas flow characteristics of bituminous coal samples. Adsorption and desorption tests were first conducted to estimate the quantity of methane that is retained by coal, and the rate at which it is released. Experiments were then carried out to study the variation in coal permeability with changes in applied stress and gas pressure - factors that change continuously with time. To further understand the phenomena involved in retention, release, and flow of gas, electron microscopy was used to study the microstructure of coal and how it affects these characteristics of coal.

Jan 1, 1988

Preliminary petrographic investigations of eight Upper Permian coal seams of the Muja sub-basin, Collie Coalfield, reveal that the coal is high in inertinite and relatively low in vitrinite and exinite contents. The exinite content of Collie coal is relatively high when compared to other Australian coal of similar age. In addition the mineral matter content of the coal is very much lower than comparable Permian coal of Eastern Australia. The higher exinite content could be attributed to the type of Glossopteris flora, and the lower mineral matter content to the environment of deposition postulated for the Collie Coal Measures.

Jan 1, 1982

By Moore A. J

This paper describes the use of a wavefront reinforcement model which has been developed to supplement established charge mass scaling methods. The model allows for the time taken for blast vibration wavefronts to travel from each blasthole, and has been successfully used to explain the reason for directional increases in both air and ground vibration in certain situations. The model has been used to identify wavefront reinforcement due to the propagation of air vibration and ground vibrations in certain situations. The paper includes a throw (or cast) blasting case history which provides multi-station evidence of the strong directional nature of wavefront reinforcement.

Jan 1, 1995

INDEX OF CONTENTSComposition of the Brown CoalsIntroductionComposition as minedComposition from drilling explorations:Latrobe Valley Area, East Gippsland, Welshpool-Alberton West Area, Altona-Bacchus Marsh Area, Lal Lal Area, Dean's Marsh Area. The Coal Constituents:Vitrain, fusain, detrital coal, resin, Sulphur, types, distribution, Ash, composition, sulphur, phosphorus, chlorine,,titanium, vanadium, distribution in seam, fusibility, source, mineral ash, chemical ash Bitumen, tar. Factors causing Variation in Composition:Pressure of overburden, moisture content, carbon, hydrogen, nitrogen, oxygen, calorific power, density, compression by warping, abnormal moisture, initial differences in vegetation, conditions of sedimentation, weathering before re-burial.Summary and AcknowledgmentsList of References

Jan 1, 1945

By Hossaini SMF

After reviewing the various approach es,namely, empirical,analytical.observational and numerical, a logical systematic approach is proposed for the estimation of compressive strength of coal pillars. In this approach first,uniaxial compressive strength of coal in pillars is estimated,taking into account the size effect and the effect of discontinuities. Next,the compressive strength of coal pillars is estimated by determining the stress distribution in the pillar and the Bieniawski strength criterion. The results appear to be compatible to the ones obtained by Wilson's method. The traditional pillar design equations give improper answers for deep workings.

Jan 1, 1991

By Hoskings R

Conceptual studies of the run of mine stockpiling and reclaiming requirements com- menced in 1975. Final selection of equipment was made in 1978 and the equipment was commissioned in June, 1979. Equipment selection was made after extensive investigation and visits to existing facilities throughout the world. The equipment selected is described and com- pared with the alternatives. Foundations were designed to minimise clean up effort and to ensure stability of equipment under design wind loading without storm bays. Program- mable logic control enables the stacking and reclaiming facility to provide a blended feed to the coal preparation plant.

Jan 1, 1980

Mixers are commonly used for the transfer of oxygen in gas-liquid-solid reactions in minerals processing. The process rate is usually controlled by two steps: gas-liquid mass transfer and reaction kinetics. Some examples are described along with the factors used for analysis of the mass transfer design problem. Typical oxygen rates and appropriate types of aeration systems or mixers are reviewed. The commonly used Rushton turbine has limitations in a number of mineral processes. The development and characteristics of the LIGHTNIN A315 axial flow gas dispersion impeller are described. Some practical examples which highlight its advantages are briefly described.

Jan 1, 1992

The first hydraulic roof supports were installed underground in 1950s and ever since that time engineering developments have improved the supports in many different ways. However. advances in three main areas, the roof support mechanical design, hydraulic engineering and electronics have ultimately led to the point where, 35 years after that first installation. automation has been achieved and is now commonplace.The history of roof support automation has involved the continual integration of high technology engineering. Thera ate further possibilities for the future which combine to give some idea of the likelihood of there ultimately being a completely manless face.

Jan 1, 1991

By Dobos SK

The Black Ridge Gold Deposit is located in the northern part of the Clermont Goldfield, which is situated at the boundary of the Bowen Basin and Anakie Inlier, Queensland. The goldfield comprises a series of NNW-trending semi-isolated basins, which are tectonically aligned with the Denison Trough, the west-most division of the Bowen Basin (Fig. 1-1).The main stratigraphic units in the deposits in younging sequence are the Anakie Metamorphics, the early Permian Blair Athol Coal Measures, the late Permian(?) White Section, and the Tertiary basalts which are regionally widespread, and intruded by abundant mafic and felsic plugs.

Jan 1, 1990

By Moort van J C

A new low-intensity magnetic separator which operates by spinning particles in a continuously rotating magnetic field is able to reduce particle entrapment of non-magnetics to an almost insignificant level. In such separators the removal of ma

Jan 1, 1997

By A Cranley, A Giblett, S Thacker

The Newmont Tanami Operations are located in the Northern Territory, approximately 550 km north-west of Alice Springs. The Granites process plant commenced operations in 1986 as a 300?000 t/a ball mill / carbon-in-leach (CIL) plant and has undergone numerous expansions between that time and the current day, with project-to-date gold production exceeding 6.5 Moz. Annual plant throughput has exceeded 2.8 Mt/a while processing a blend of open pit material and ore from the Callie Deeps underground mine, with annual gold production exceeding 400 koz. In 2013 the operation processed 1.8 Mt of underground ore for the production of 323 koz of gold.This paper reviews the operation and expansion of The Granites process plant since the mid to late 1980s with particular focus on the gravity gold recovery circuit. The Tanami ores contain significant levels of free gold, and gravity recovery has long been an integral component of the metal recovery process at the Granites plant. The results of ten years of gravity circuit performance analysis and optimisation are presented.CITATION:Giblett, A, Cranley, A and Thacker, S, 2014. Three decades of gold production at the Newmont Tanami operations, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 209–216 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By G Pasin, F Wirfiyata, G Khomaeni, W Valery, A Maclean, A Jankovic

The grinding circuit at PT Newmont Nusa Tenggara (PTNNT) – Batu Hijau mine consists of two SABC (semi-autogenous milling, ball milling, pebble crushing) trains, including four 20'?×?33'6? ball mills that have been lined with steel liners since the commissioning of the plant in 1999. During 2011 and 2012 an industrial trial was conducted to evaluate Poly-Met liners (a combination of rubber and steel liners). These new liners were installed in two of the ball mills (ball mills 1 and 2) and operated in parallel with ball mills 3 and 4 with steel liners.The objective of the trial was to compare the plant performance with the Poly-Met and steel ball?mill liners with regards to wear life, mill throughput, grind size and total unit costs. The trial was conducted over the entire life of the liners. The evaluation methodology implemented consisted of frequent spot sampling around the ball mill circuits, complete surveys/audits in both ball mills, and detailed analysis of process data. This paper presents the results of the industrial trial and main conclusions.CITATION:Maclean, A, Wirfiyata, F, Khomaeni, G, Jankovic, A, Pasin, G and Valery, W, 2014. Ball mill Poly-Met liner evaluation at PT Newmont Nusa Tenggara – Batu Hijau mine, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 255–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Drury SA, Williams RD, Nind DC

The Airborne Thematic Mapper is an eleven channel digital scanner which acquires image data in the visible, near infra-red, short wave infra-red and thermal infra-red wave- lengths. A description of the system is presented which includes details of the operating wavelengths and performance parameters of the scanner. Consideration is also given to the aircraft installation requirements. During January 1984 the scanner surveyed the mineral rich areas of Leonora, Laverton and Kalgoorlie in Western Australia. This is a region of intense exploration activity for gold and base metals. Some 30,000 square kilometres were systematically surveyed in a period of ten days. This scanner was flown at 7,000 metres altitude giving a ground pixel size of 17.5 by 17.5 metres. The flight line spacing was 8 kilometres. The overall project took some thirty days from conception to completion. The planning and execution of this operation are described in detail. The resulting magnetic tapes provided 11 channels of digital image data over a 30,000 square kilometre area and a variety of image processing techniques were employed in order to capitalise fully on the results. The imagery provides a powerful tool for the geological mapping of the terrain. The data can also be used to monitor the environmental effects of mining operations.

Jan 1, 1986

By A Reschke

The Thiess John Holland Group is undertaking the design and construction of Brisbane’s Airport Link Project, the largest single investment in transportation infrastructure in Australian history. Twin Herrenknecht TBMs are being used to bore parallel road tunnels from Kalinga Part in Toombul through to Lutwyche, a distance of 2.45 km. At 12.48 m, these tunnel boring machines (TBM) are the largest diameter machines, outside of Japan, to incorporate annular two-component type grouting through the tailskins.Grout design, preparation and injection have been given particular attention in this project in order to push the boundaries of achievement. Laboratory testing was conducted on various mix designs to ensure the contract specifi cations for grout strength could be met. To study the mechanics of the grout injection process, Herrenknecht supplied a test rig which duplicates the grout injection systems on the TBMs. Multiple recipes were tested, carefully selected to balance the requirements of rapid strength development with high mobility (to completely fill the void between the segmental lining and the ground) and minimal bleed.Team Mixing Technologies, Canada, was selected as the grout plant provider based on the technical performance of their high shear colloidal mill mixers. Field results have shown that the colloidal mixer prepared grout gives almost double the strength of an identical grout prepared by a paddle mixer.

Mar 8, 2011

By E Hernandez, I Agustian, W Kusumohastuti

PT Freeport Indonesia is completing the first underground gyratory crusher excavation at their Deep Mill Level Zone (DMLZ) mine located in the mountains of Jayawijaya, District of West Papua, Indonesia. DMLZ is an underground block cave mine with an expected output of 80 000?t/d and a scheduled production start in 2015.In order to deliver crushed ore to the mill through the existing conveyor belt, the DMLZ block cave mine will construct two 1000?kW 1.6?×?2.3?m gyratory crushers with their own respective ore flow conveying systems underground. Each crusher is composed of top, middle, and bottom chambers with an ore bin. This system includes a series of high capacity conveyors approximately 5 km in length including transfer stations and support facilities.The development methodology required a combination of lateral development by jumbo drilling machines and vertical development by mechanised raise climbers (MRC) due to the complexity of the chamber design.This paper will discuss the project scope, design and development methodology, ground conditions, innovative survey controls, and the challenges faced due to the remote location.CITATION:Hernandez, E, Kusumohastuti, W and Agustian, I, 2014. Excavating the first underground Gyratory Crusher at the Deep Mill Level Zone mine, PT Freeport Indonesia, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 43–50 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Lockhart D. A, Gleeson P, Lang S. C

The Glenrock Group forms the uppermost part of the Early Devonian to Early Carboniferous Burdekin Basin sequence in the Townsville hinterland, north Queensland. As redefined, three formations make up the Glenrock Group. The Percy Creek Volcanics (base), the dominantly epiclastic Mount Douglas Formation, and the Horse Pocket Volcanics (top). The Ellenvale beds unconformably overlie the Mount Douglas Formation and Percy Creek Volcanics and have been excluded from the Glenrock Group as defined by Wyatt and Jell (1980). Three facies associations are recognised in the Mount Douglas Formation: Alluvial Plain facies, Alluvial Fan facies and Lacustrine facies.Deposition of the Glenrock Group, began with the eruption of massive basalt and basaltic andesite lavas, probably in a volcanic arc setting. With time, the volcanism evolved to become more dacitic to rhyolitic in composition. Waning of the volcanic activity appeared to coincide with uplift of source areas (probably to the west). Deposition on an alluvial plain during this waning volcanic cycle, gave way to alluvial fans at the margins of the uplifted terrain. As the uplift ceased and the system became more mature, the alluvial fans gave way to widespread lakes. Rhyolitic ignimbrite and airfall tuff, interbedded with the alluvial plain, alluvial fan and lacustrine facies, indicate that some volcanism continued, probably vented in the uplifted terrain to the west.

Jan 1, 1990

It is often said in business that if you donÆt have a customer you donÆt have a business. The same rule applies to project evaluation; if you donÆt have customers you really donÆt have a viable project. It is therefore essential that in the early stages of project evaluation the following fundamental questions are addressed: What products will this project produce? Who are the potential customers? What are the customersÆ requirements with respect to grade and impurities? Do they have adequate capacity to take the production from the proposed project? Will the products introduce adverse effects in the customerÆs process circuits? Will additional waste streams requiring disposal be produced? In the past the attitude has been along the lines of the customer will take whatever we produce at the mine site. Times have now changed with customers now operating under much tighter environmental regulation with waste disposal becoming increasingly difficult. It would therefore be prudent that the principles of product stewardship be used as a tool in project evaluation. This paper will provide a general discussion on customer requirements and provide detail on case studies of the impact of mine products on smelter process circuits. It will provide examples where there were synergies between the mine product and the smelter circuit and where the mine product had adverse impacts on smelter performance.

Jan 1, 2007

The classical view of island arc geology is that of a plutonic intrusive/volcanic extrusive complex, derived from the products of oceanic lithosphere subdu.ction and constructed on an over-riding plate of oceanic origin. Such an arc is typically backed by a marginal basin, formed by seafloor spreading of a more or less conventional kind. Various studies undertaken over the last decade have modified this picture and provided a new tectonic framework within which to explore for resources. Formation of Marginal Basins During the 1970s, seafloor spreading magnetic anomalies were identified in various marginal basins in the SW Pacific. In one of these, the South Fiji Basin, there was clear evidence of a ridge-ridge-ridge triple junction, although no kinematic relationship to the major plate boundaries was determined. Palaeomagnetic studies conducted in Vanuatu and Fiji, and in the Bismarck Archipelago of PNG provided evidence of large scale arc rotations relative to major plates. This indicated a general pattern of marginal basin formation by ridge-ridge-ridge triple junction growth together with island arc growth by trench-ridge-trench triple junction evolution. Formation of Primitive Island Arcs The triple junction growth model strongly suggests that at least a significant amount of arc evolution occurs by the initiation of subduction at a spreading ridge. This has predictive implications for the nature of island arc basement.

Jan 1, 1987

The type of population encountered in the sampling of coal, ores and other products of natural phenomena is one in which the variance within a cluster of elements generally increases steadily as the size of the cluster increases. To enable estimation of variances of stratified random or systematic sampling for such populations one must model the serial correlation function or alternatively, the variogram function. The author has postulated a specific symmetry of the serial correlation function which leads to expressions with rich theoretical and practical implications. These expressions provide a spatial correlation function which explains power law relationships often observed in studies of dispersion variances. They also enable straightforward calculations of sampling variances. The importance of the role of finite population size in the equations leads one to examine previously held concepts of ælargeÆ and æsmallÆ sample populations. The model based on the symmetry postulate is a fractal model with the serial correlation function of a hypothetically infinite population being of the same form as that developed by Mandelbrot for discrete fractional noise. Techniques used in fractal mathematics apply, including box counting and fitting of a dimension function. The paper establishes a framework for the understanding of this fractal theory and demonstrates how to calculate sampling variances from the model variogram using simulated data fitting the model.

Jan 1, 2008

Project evaluation is completed through individual studies covering technical and financial aspects of the mine to market. These studies are completed at various levels of detail depending on where the project evaluation is in the projectÆs life cycle. The competency of the studies varies in relation to the quality of data, level of the skills employed, control, management and reporting structure. The focus of this paper is managing elements of the study, looking at the cost of opportunity to influence the project, against the value added. Selection of the study manager and study teams is central to getting an integrated project evaluation addressing the correct issues completed on time. Retention of key personnel can reduce rework which, in turn, can reduce time and cost impacts. It is important to have a work breakdown structure at the outset so that the study teams have a common numbering and naming system that will integrate areas, equipment, budgets estimates and accounts. Having set up the evaluation groups and provided training in the study procedures, understanding the scope and schedule are vital elements in producing a project evaluation that addresses the opportunities and the risks of the final project. Arriving at an accurate capital budget requires integration of the research controlled through common systems. Project evaluation process must also address how the project is to be delivered.

Jan 1, 2007