Search Documents

By R Fanni, D Reid, M Kulessa

Recent updates to Australian industry guidelines emphasise the importance of the assessment of liquefaction potential of tailings. This includes assessment of the cyclic liquefaction potential, and the post-seismic strength of tailings expected to undergo strength loss from seismic loading. Despite this increase in focus, a relatively small number of Australian tailings appear to have been characterised through cyclic and post-cyclic testing. This paper presents the cyclic characterisation of four Australian tailings, consisting of iron ore, lateritic nickel, vanadium and bauxite residue. Material was obtained either from surficial tube sampling or through remoulding samples in the laboratory from slurries. Testing consisted of monotonic, cyclic and post-cyclic tests for each material. For three of the materials, laboratory-scale shear vane testing was also performed to provide a comparison to post-cyclic strengths from direct simple shear.The results indicated cyclic resistances consistent with the results of other tailings presented in the literature. The lateritic nickel tailings provided the greatest cyclic resistance of the four materials tested, followed by the vanadium tailings. This was somewhat consistent with expectations for material behaviour based on index properties. Post-cyclic strengths were seen to decrease as cyclic strains increased, consistent with typical observations in the literature. Following significant cyclic straining, in some instances the post-cyclic strengths approached those obtained through residual shear vane testing. This provides further insight into the strain-dependent nature of post-cyclic strengths for some materials. The implications of these observations on the post-seismic stability condition are discussed.CITATION:Reid, D, Fanni, R and Kulessa, M, 2015. Cyclic and post-cyclic behaviour of four Australian tailings, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 207–214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By A M. Myrvang, B Nøst, N Q. Trinh, I S. B Bergh

The iron ore producer Rana Gruber AS is situated in northern Norway just below the Arctic Circle, and has been producing hematite and magnetite concentrates for more than 60 years. Since the late 1990s, the major part of the production comes from a sublevel stoping underground operation after many years of open pit mining. Despite moderate mining depth, the operations have experienced considerable rock stress problems due to quite high tectonic, horizontal stresses. To manage the problems, comprehensive rock mechanics investigations have been carried out by SINTEF, a major contract research organisation. This has included in situ rock stress measurements, laboratory investigations and numerical modelling. Based on this and practical experience, satisfactory design of vertical and horizontal pillars was achieved. At depth, the ore width increases from 30–40?m to more than 100?m. This, together with a major planned increase in production, called for a change of the mining method. After thorough investigations and considerations, it was decided to change to sublevel caving, very much like the LKAB system. The development of the new system has been closely followed up by rock mechanics measures, including 3D numerical modelling and comprehensive monitoring of deformations and rock stress changes. To achieve a satisfactory caving of the hanging wall, all vertical and horizontal pillars in the sublevel stoping area had to be removed. This has been a challenging task, and the development of the caving has been slow until recently. However, now the caving develops satisfactorily.CITATION:Bergh, I S B, Trinh, N Q, Myrvang, A M and Nøst, B, 2014. From sublevel stoping to sublevel caving at Rana Gruber, Norway – rock mechanical aspects, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 323–330 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

Vertical flow systems (SAPS, vertical flow wetlands) are increasingly used for passive treatment of mine drainage that is net acid. Data on 30 systems in eastern US show that well designed systems typically add about 40 g/d/m2 of alkalinity to influent net acid water. If they are designed with a conservative loading rate of 25 g/d/m2 and carefully constructed, they produce net alkaline water. Alkalinity added depends on influent acidity, Fe, pH, and retention time, and ranges widely, from 7 to 484 mg/L, so this is not a useful design criterion. Some waters may benefit from retention times longer than the conventional 12 - 16 hours, but the design must be partly based on cost-benefit considerations. Systems with fine limestone added to the compost layer perform better than average, perhaps to an alkalinity generation rate of 80 g/m2/d. A variety of problems are noted in the 30 systems and others reported in the literature. Systems with high influent Fe (> ~75 mg/L, varying with pH) tend to gradually decrease in flow rate because of precipitation and settling of Fe hydroxides on top of the compost layer. Some high-Fe systems precipitate Fe in the limestone layer, suggesting inadequate compost thickness, or short-circuiting through thin spots. Systems with Al exceeding about 10 mg/L tend to plug because of Al hydroxide precipitation in the limestone layer. Flushing only removes a small part of this precipitate, but can extend life. Some systems are ineffective because of failure of the inflow system. Some systems are uneconomic because they are oversized. A continuing program of inspection and maintenance is necessary for long-term performance.

Jan 1, 2003

By M Sciortino, J Korczak, J Muinonen, A St-Jean

The Dumont deposit is a large (1179 Mt reserve), low-grade (0.27 per cent nickel) nickel sulfide project located in the Abitibi region 25 km west of Amos, Quebec. Royal Nickel Corporation (RNC) acquired the project in 2007 and has since taken the deposit through to feasibility. The disseminated nickel sulfide and alloy mineralisation is hosted within the serpentinised dunite subzone of the Dumont Sill; a differentiated, pervasively serpentinised, ultramafic sill of komatiitic affinity. Pentlandite ((Ni,Fe)9S8), heazlewoodite (Ni3S2) and awaruite (Ni2.5Fe) are the dominant nickel-bearing metallic phases and can be recovered by conventional methods (flotation, magnetic separation). Non-recoverable nickel is also present within serpentine and olivine of the silicate matrix.A detailed mineralogical program including 1420 QEMSCAN« samples and 4400 electron microprobe points was undertaken to increase the understanding of the nickel deportment in the various recoverable and non-recoverable phases in a spatial context across the deposit. A total of 105 metallurgical tests have been performed under a standard procedure which have linked the mineralogy to metallurgical performance. This has allowed the creation and modelling of geometallurgical domains on a block-by-block basis to understand the recovery variation and metallurgical performance throughout the deposit. Understanding the spatial variability of Ni deportment in recoverable and non-recoverable phases through mineralogy is the key to understanding metallurgical performance, thus unlocking the value of the Dumont deposit and other large tonnage low-grade ultramafic nickel deposits.CITATION:Sciortino, M, Muinonen, J, Korczak, J and St-Jean, A, 2013. Geometallurgical modelling of the Dumont Deposit, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 93-100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By R Mann, R Prasad, S Vink, V Nanjappa

The level of salinity that various aquatic organisms can tolerate without incurring any adverse effects is dependent on several environmental and evolutionary factors. These factors include the relative concentrations of different types of dissolved salts in the water that makes up their habitat, the regimes to which organisms are exposed to waters of differing salinity levels (including naturally derived variations), the degree to which an organismÆs life history stages have adapted to salinity, an organismÆs ability or behaviour to avoid adverse levels of salinity and an organismÆs capacity for osmoregulation.Release of saline water into rivers of the Fitzroy catchment has created concern about the impact on aquatic organisms. Not only is salinity itself a stressor on organisms but different ionic compositions will moderate the effects. Ecotoxicology experiments were conducted using artificial saline water based on mine water chemistry using sensitive macroinvertebrates collected from the catchment, as well as a range of laboratory organisms in accordance with the ANZECC and ARMCANZ (2000) guidelines. The 95 per cent ecosystem protection value calculated from species sensitivity distribution derived from the commercial tests was estimated to be ~2.0 mS/cm. For the protection of 99 per cent of the species the salinity has to be reduced by more than 50 per cent to 0.91 mS/cm. The electrical conductivity (EC) values, derived by commercial testing and species sensitivity distribution in this study suggests that salinity contaminant trigger values previously developed using a referential approach for protection of aquatic ecosystems from saline mine water releases in the Fitzroy may be conservative.CITATION:Vink, S, Mann, R, Nanjappa, V and Prasad, R, 2013. Determining the impacts of salinity on freshwater organisms, in Proceedings Water in Mining 2013 , pp 149-154 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By A Flatten, F Reusch

Recent advances in the disciplines involved in simulating large mining operations provide increasingly precise and accurate methods for the study of cave mechanics; however, in large regional-scale models, hydrological aspects are often neglected or studied independently from the mechanical problem. There exists a great demand for a unified approach to study and simulate both the mechanical and hydrological phenomena that allows for a more detailed understanding of the effects of groundwater flow, dewatering and the impact on block cave mining operations.This paper presents a numerical framework that combines three-dimensional regional-scale hydrological simulation techniques for groundwater flow, together with non-linear continuum–discontinuum rock mechanics models, provides such a unified modelling approach. The underlying simulation technique is based on a coupled parallel solution formulation adopting single-phase fluid flow formulations into a discontinuous, strain softening and dilatant finite element model. This approach is adopted for the presented case study of a realistic block caving example in a simplified unidirectional coupling formulation, to investigate the effects of the mechanical analysis on the hydrological response. Here, particular emphasis is on the non-linear coupling of the deformable and strain-softening solid skeleton and fluid phase; eg the change of hydraulic properties with evolution of damage in the rock mass and large-to-intermediate scale structures due to ongoing caving operations. The importance of discontinuum structures is discussed, as mining-induced fault reactivation significantly influences the hydrological response.CITATION:Flatten, A, Reusch, F and Beck, D, 2016. The application of hydromechanical mine-scale modelling for large block caving operations, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 341–348 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By D Reid

Run-out analyses of tailings storage facilities are typically undertaken using methods based on rheological theory. These are reasonable techniques to model the behaviour of tailings that, through significant run-out and possibly mixing with supernatant water, are generally acting in a fluidised manner. Such modelling often follows on from two-dimensional continuum analysis models where, if failure is predicted, grid failure often occurs when deformations begin to increase. This results in a disconnect between the prediction of failure and the modelling of the potential extent of the failure.Recently, rezoning methods have been incorporated into commercially available two-dimensional soil mechanics deformation codes. Rezoning techniques enable large deformations to be modelled within a two-dimensional continuum analysis framework; however, while promising, the use of such tools is not yet widespread, and a consensus is yet to develop on how they should be applied to tailings dam run-out modelling.This paper uses FLAC rezoning techniques to model the flow behaviour of two historic tailings dam failures. The purpose of these analyses is to critically assess the performance of rezoning against some available historic failures. The required data to undertake such an analysis is outlined, along with the inherent limitations and assumptions required. Parametric analyses are outlined to address some of these issues. In general, the analyses undertaken underestimated the flow distance observed in the historic failures by varying degrees; however, in some instances, the analysis reasonably reproduced the qualitative shape of the initial failure zone. A variety of potential reasons for the discrepancy between historical observations and the models undertaken are provided.CITATION:Reid, D, 2015. The use of rezoning techniques to model historic tailings failures, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 201–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By N Redwood, N Fowkes, A Bassom, S Durkin

"It is well known that from time-to-time a vehicle will interact with a bund or windrow and often the barrier is insufficient to safely arrest that vehicle. The result of such an incident is often catastrophic. Regulations around the requirement for edge protection near pit edges vary between jurisdictions. Generally in Australia regulations tend to be around placing the responsibility on the mine operator to provide ‘adequate’ or ‘appropriate’ edge protection. Guidelines often place a minimum height of bund at between half and two-thirds the diameter of the largest tyre on-site.Safescape has identified the opportunity to improve safety in open pit edge protection and is currently developing the Edge Protector (EP) product. The EP is designed to create a vertical front face to a conventional broken rock safety bund. The fundamental premise of the product is that by creating a vertical front face to the bund, trucks cannot easily drive up over the bund and instead have to push through the rock to get to the other side.In addition to providing a safer system for arresting vehicles, the vertical front face also means that extra space is made available in the haul road. This can either be used to facilitate larger trucks or when designing a new mine, with an increase in overall pit slope.This paper outlines the research and development of a new edge protection product. Discussion will include project objectives, economic incentive for mines to apply the system, mathematical analysis of the truck/bund interaction and physical testing of the product.Citation:Durkin, S, Fowkes, N, Redwood, N and Bassom, A, 2016. Innovative Approach to Open Pit Edge Protection, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 138–149 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

The Ernest Henry Mine is an open pit copper-gold mining operation located in north-west Queensland, Australia. It is owned and operated by Xstrata Copper with a current concentrator throughput of approximately ten million tonnes per annum. The pit will cease mining towards the end of 2010. Extensive surface diamond drilling has confirmed an extension of the orebody to depths of 1000 m below surface. A prefeasibility study was commissioned in late 2006 to investigate underground mining options with the preferred mining method being an inclined sublevel cave. In February 2008 mining of a decline commenced in conjunction with a feasibility study to further investigate the project. Work from the prefeasibility study indicates that an underground crusher, conveyor and hoisting shaft could be utilised to crush and transport broken ore from the sublevel cave workings to the concentrator. The study suggests that a production rate of five million tonnes per annum could be achieved and sustained for up to ten years. Ventilation designs and requirements will form a large section of the feasibility study. This paper will detail investigations of preliminary ventilation network designs of the proposed sublevel cave. Work has been completed using both Ventsim and VumA ventilation simulation packages. Ventsim was used to provide preliminary estimations and suggest alternatives for: surface fan duties;airflow characteristics (direction, velocity, pressure and quantity); andventilation network design in key mine areas. With mining activities reaching depths in excess of 1000 m below surface an analysis of heat conditions should be conducted. The VumA software package was used to model the thermal properties of the ventilation system. This model will provide a basis for the preliminary decisions on refrigeration requirements for the mine.

Jan 1, 2008

By M I. Pownceby, N A. S Webster, J R. Manuel, J M. F Clout, E Donskoi, N A. Ware

The relative influences of sinter mineralogy, sintering temperature, solid and pore macro- and microstructure on iron ore sinter physical strength are not yet fully understood. Whilst a range of analysis techniques have been used by researchers to evaluate sinter physical properties and sinter mineralogy, none have been able to directly link sinter mineralogy and physical strength under controlled conditions. CSIRO has developed a unique laboratory method to study the fundamental melting properties of fine iron ores in a laboratory furnace under a controlled temperature and gas atmosphere environment designed to simulate the industrial sintering process. Compacted tablet samples for a 0.41 per cent and a 2.5 per cent Al2O3 series were fired in a tube furnace at various temperatures, cooled, then tumbled using a modified Bond abrasion test apparatus to determine a relative tumble index (TI) at each temperature. Quantitative XRD (QXRD) analysis was then carried out on the tumbled samples and optical image analysis (OIA) was conducted on polished sections of a separately fired compact in each case. The amount of total SFCA was found to decrease with increasing firing temperature for both alumina series with the total amount of SFCA higher in the 2.5 per cent Al2O3 series compared to 0.41 per cent Al2O3 series samples. The increase in the amount of magnetite and hematite with increasing firing temperature was largely at the expense of a decrease in total SFCA. Overall, there was good agreement between the quantitative mineralogy determined from QXRD versus OIA for SFCA, hematite and magnetite. Qualitative analysis of high magnification images of the sinter correlated with both the OIA and QXRD results.

Sep 18, 2023

By B Roache

Ground support installation into the face of development headings has become an accepted practice at many Australian hard rock mines. Ground support is installed in the development face to reduce personnel exposure to rockfall while conducting work tasks such as marking up, installing lifter tubes, charging, and face sampling. The ground support system installed in the face is typically friction bolts and mesh. This support system can be effective at reducing rockfall occurrence, but it also increases the cost of development per metre, in terms of capital for the ground support, jumbo and operator capital allocation and the installation time slowing each drill and blast cycle. Other issues associated with meshing and bolting the development face include management of rock bolts and mesh sheets in the fired dirt of every cut, damage to services such as vent duct, geometry issues when installing ground support onto irregular development profiles and operator error. Fibrecrete installation onto the development face for support is an option considered by many mines, but it can be difficult to manage due to the removal of visual indications of misfires and slowing the mining cycle due to the wait time for fibrecrete curing. The use of Thin Spray Liner (TSL) products in underground hard rock mines has been relatively infrequent in the past, mainly due to issues with cost, health and safety, and liner strength. Kanmantoo Mine investigated the use of TSLs for the purpose of development face support, while collecting data on the costs and practicalities associated with their use. Several TSL products were trialled and a preferred TSL product was selected for use as face support. Cost savings, drill and blast cycle timing improvements and other benefits were achieved while meeting the requirement to reduce rockfall risk.

Mar 29, 2023

By C M. Standen

The SAG mill at Rasp Mine has undergone a number of liner design modifications since commissioning in 2012, making liner wear and failure difficult to predict from historical data. During 2017, several instances of liner failure or near failure were experienced resulting in unplanned downtime for emergency relines or to patch liners in the lead up to a planned shutdown. The strategy for relining mills is often to minimise the frequency of relines (and subsequent shutdown costs) by extending liner life, achieved through design modifications. However, it was observed that as the Rasp SAG mill liners wear, mill performance declined with power draw increasing and throughput declining. Opportunity and inefficiency costs start to erode the revenue per additional tonne milled for a given set of liners, and in turn the benefit of delaying relines. As such, optimising the frequency of relines becomes a trade-off between reline costs and opportunity/inefficiency costs in delaying relines. The aim of this paper is to demonstrate a frame work for analysing costs using a marginal economic analysis with the assumption that the Law of Diminishing Returns can be applied to the life of mill liners. The SAG mill operating variables can be modelled to determine their impact on costs and an optimal reline point can be defined where the total costs are minimised. This prevents unexpected failures due to accelerated wear by providing justification to reline earlier and thereby allowing efforts to be focused on sustaining milling performance.CITATION:Standen, C M, 2018. An economic approach to optimising mill reline frequency – a case study of SAG mill relines at Rasp mine, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 197–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By A K. Bhatnagar, S Saha, P Dixit, A K. Mukherjee, P Patra

TATA Steel’s R&D Division at Jamshedpur has developed a slime beneficiation process to recover iron values from iron ore slime. This process recovers iron ore concentrate containing 2.2 per cent alumina from a feed containing 7–10 per cent alumina. The reject generated from beneficiation of iron ore slime is treated as waste as the iron content in the reject is below 45 per cent. Effective utilisation of this waste is required for making the iron ore slime beneficiation process a zero-waste technology. In this connection several studies were made towards utilisation of slime waste. One of these studies revealed that slime waste can be used as a soil conditioner. Slime waste contains particles of size less than 10 micron and when these particles are mixed with soil in definite proportions, the porosity and the permeability of the mixture goes down. As a result, the water holding capacity (WHC) improves. This concept was evaluated through a series of tests at greenhouse level to optimise the soil to slime ratio. Finally, a pilot scale field trial was carried out over a period of three months using paddy rice as the crop. Three separate plots with compositions of: soil + organic matter comprising Farmyard Manure (FYM), (ii) soil and slime waste (2:1) + organic matter (FYM), and (iii) soil and slime waste (2:1) + organic matter (FYM) + Nitrogen, Phosphorus and Potassium (NPK) fertiliser were used for the pilot trial. The results showed a 20 per cent increase in the productivity of paddy rice for plot (ii) as compared to plot (i). This was due to the beneficial effect of slime waste in the soil. The addition of inorganic fertiliser such as NPK in the ratio of (4:2:1) further enhanced the productivity of paddy rice.

Sep 18, 2023

By H Park, D J. Holland, L Wang, Y Matviychuk, Y Lee

Reuse of process water in mineral and coal flotation plants is widespread to effectively reduce freshwater consumption. However, the accumulation of the frother in the recycled process water is a growing problem as high remnant frother concentration often leads to undesirable overfrothing issues throughout the plants. Various approaches have been proposed by others to measure frother concentration, but none of them is used in flotation practice owing to the requirement of timeconsuming sample preparation steps and/or specialist training to operate and maintain. There is a pressing need for the development of a simple and fast frother concentration measuring technique to avoid overfrothing issues and to optimise the flotation process. The present paper presents two promising approaches to measuring frother concentration online. The first approach measures the concentration of alcohol type frothers based on the host-guest interactions between frother molecules and a formulated liquid. This method is simple and fast as it only requires mixing the formulated liquid with the water sample for up to one minute. The potential of this approach was demonstrated by determination of the residual MIBC concentrations at different locations across a coal flotation plant. The second approach measures frother concentration using a solid-phase extraction (SPE) process and a cryogen-free benchtop NMR spectrometer. Using this approach, both alcohol type and polyglycol type frother solutions can be analysed for concentration determination within 30 minutes. It has also been demonstrated that the concentration of individual frothers in a frother blend (ie MIBC and PPG425 in water) can be accurately analysed even in the presence of background chemicals. This technique has otential for real-time measurement of frother concentration as the whole process can be fully automated.

Aug 24, 2022

By T Higuchi, T Yamamoto, K Takehara

Iron ore fines are used as raw materials for sintered ore for blast furnaces in the world. Since the production and quality of sintered ore have a great influence on the stable operation of a blast furnace, many technologies were developed for controlling the heat profile in the sintering machine, which largely affect the sintered ore properties. In particular, the influence of oxygen in the suction gas, which plays an important role in combustion, was investigated over the years. It is known that increasing the oxygen ratio by about 30 per cent not only significantly improves the combustion rate, but it also increases the strength and yield of sintered ore. However, the details of the mechanism for improving these qualities are unknown. In this study, we investigated the influence of oxygen enrichment at higher ratios (O2: 21–40 per cent) and tried to understand the sintering behaviour enhanced by oxygen. The effect of oxygen enrichment on sintered ore quality and the heat profile were evaluated by sintering tests using a quartz glass pot. From the results, sintered ore yield had a maximum value for O2 = 30 per cent, but strength was increased for O2 = 40 per cent. From heat pattern analysis, it is clear that the high temperature holding time also reached a maximum at O2 = 30 per cent. Furthermore, we found that with increased oxygen ratio, the combustion speed (flame front speed) was increased, but the area of combustion was enlarged. It is considered that there could be a maximum oxygen ratio value for the yield from the balance of these positive and negative effects on high temperature holding time. To clarify the reason for strength improvement, thermodynamic calculations were performed and it was found that melting behaviour could be improved by changing the oxygen ratio.

Sep 18, 2023

By A R. Hollis, M Heddon

The safe life cycle of a Tailings Storage Facility (TSF) is founded on the fundamentals of proper design, construction, operation and closure. Leinster Nickel Operations (Leinster) utilises four active TSF cells that are cycled between filling (deposition), desiccation, and construction to meet a targeted rate of rise. This results in ongoing and consistent raising of the TSF walls. Critical to maintaining the safe life cycle through this consistent wall raising is precision construction and high frequency quality assurance to ensure compliance to design requirements and TSF walls free from defects. Leinster has recently deployed Intelligent Machine Control technology for TSF construction. Advances in Intelligent Machine Control have decreased variability in construction; ensuring variations are within the tolerances of design. The Intelligent Machine Controls are programed to ensure construction conforms to design tolerances of +/-30mm. This level of accuracy provides assurance of borrow area set out, compacted layers are as per design, compaction monitoring is within the zone placed, scarification between layers to prevent lamination is maintained, and batter angles are set to the correct grade. This level of control provides certainty that construction meets the design intent. In conjunction with Intelligent Machine Control, periodic drone surveys are conducted to verify construction against design. Advancement in survey equipment and techniques allow higher frequency, high accuracy survey to be completed on demand by site based personnel. This provides quality assurance through all stages of the construction phases, as well as the final constructed wall, ensuring compliance to design. Combining Intelligent Machine Control with higher frequency quality assurance provides an increased level of certainty that the TSF construction is defect free and within quality specifications. These recent technological advancements in Construction and Quality Assurance ensure cell raises are constructed to the design intent with greater levels of accuracy and precision than ever before.

Jul 1, 2021

By H Wang, D Wang

Mine dust is the most serious occupation hazard in coalmines. And many coal workers suffer from pneumoconiosis because of long-term inhalation of respirable dust. Reducing the dust concentration of workplaces by effective technical means is an important way to prevent coal worker’s pneumoconiosis (CWP). In order to overcome deficiencies in existing dust control technology for underground mining, especially the disadvantage of water spray technology mounted on roadheaders or continuous miners, the authors developed an integrated dust suppression technology utilising foam for fully mechanised heading faces. This paper presents an overview of the principles, materials, equipment and application of this technology. Among these, a jet type foaming device and a green foaming agent were developed, which can realise the goal of efficient preparation of foam. In addition, an arc fan nozzle used for foam spraying was invented, which can effectively cover and enwrap the dust produced by the roadheader at the cutting point and achieve the goal of efficient utilisation of foam. This dust suppression application of the proposed foam technology was investigated on fully mechanised heading faces. The results show that the dust concentration was cut down significantly with a dust suppression efficiency of greater than 85 per cent, an increase of over 30 percentage points compared to the water spray system. This study demonstrates that this foam technology can play an important role in dust suppression on fully mechanised heading faces, which provides an important method to improve the working environment and protect coal workers’ health.CITATION:Wang, D and Wang, H, 2015. Technology of dust suppression by foam for fully mechanised heading face, in Proceedings The Australian Mine Ventilation Conference, pp 177–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By D G. Rantucci

Organic carbon is a major ore contaminant at MMG’s Century mine. This carbonaceous matter is associated with shale hosted sphalerite mineralisation. It occurs as elongated lamellae and as inclusions in porous sphalerite aggregates which are fine grained and difficult to liberate from sphalerite. The carbon prefloat circuit was designed to remove the liberated organic carbon in order to mitigate excessive reagent consumption, contamination of the lead and zinc concentrates and poor flotation performance in the primary zinc circuit. The consequence of organic carbon removal is that sphalerite and galena minerals are lost to the prefloat concentrate. A Jameson Cell was installed in late 2005 as a prefloat cleaner cell. Operational experience showed that the cell became capacity limited during periods of high amounts of organic carbon in the feed and was subsequently bypassed.Reactive style operating strategies were implemented to manage the effects of insufficient organic carbon removal by the prefloat circuit but due to the relatively large circuit residence time, upstream changes meant hours before the downstream circuits were stabilised following a disturbance from excess carbon.This paper describes the modifications and testwork undertaken to enable the Jameson Cell to be operated during periods of high organic carbon in the float feed and the implementation of process control initiatives to proactively remove the required prefloat mass from the float feed to eliminate the reactive style operating strategy.The process control modifications centred on dynamically targeting a prefloat mass recovery determined by an equation relating the carbon to zinc ratio to the carbon prefloat mass as a percentage of the float feed. The equation was developed by analysing historical data. These improvements served to optimise the prefloat circuit and consequently stabilise the downstream lead and zinc circuits.

Aug 8, 2011

By M Pyle, T Vizcarra, G Ballantyne, B Foggiatto

Bulk Ore Sorting (BOS) has the potential to add significant value to mining operations by manipulating the feed grade and throughput to the processing plant. However, assessing the performance of BOS is complex, as it is influenced by geology, equipment, spatial and time domains. This increases the risk (real and perceived) of the technology. To manage risk, brownfield operations have the option to: (a) first test the variability in feed grade using a detector on the feed conveyor and subsequently construct the diverter and associated materials handling equipment when the value is established; or (b) conduct site trials with standalone sorting plants. The approaches described for brownfield projects are not available for greenfield projects where the in-situ heterogeneity needs to be quantified and translated into an economic evaluation to test the viability of BOS. Ausenco has developed a methodology that allows assessing the in-situ ore heterogeneity and uses an in-house technoeconomic model to determine the value of BOS for greenfield projects and assess the effects of sorting performance on project economics. The in-situ grade heterogeneity can be measured on a length of drill core and fitted to a mathematical model to assign a heterogeneity index. Given the spatial location, this heterogeneity index can be mapped across a deposit in combination with the average grade. Linking this information with relevant mixing models can determine the likely technical performance of BOS at an operation. However, the real value is only realised when this technical understanding is linked with an economic model and used to optimise the mine plan. Three case studies will be presented that show how Ausenco applies this methodology to assess the value of bulk ore sorting for greenfield studies.

Nov 10, 2020

The Osborne copper-gold deposit (within the Trough Tank project area) is located in the Cloncurry Shire about 195 kilometres south-east of Mount Isa. It is hosted by Proterozoic metasediments of the Eastern succession of the Mount Isa Inlier. The deposit is overlain by 25-40 metres of Mesozoic cover, so it represents a true "blind target". Placer Exploration has 100% outright ownership of the property, having purchased the remaining 10% interest in the property from Shell in early 1993.Intensive exploration, both surface and via drilling at Osborne, has taken place since 1985, when CSR Limited Mineral Exploration and Development Group (acquired by Placer in 1988) entered into a joint venture with Billiton Minerals. Exploration effort from 1985 to June 1988 outlined a 20 kilometre strike length of magnetic horizons, in what was termed the North-East, Central and Southern anomalies, which were drilled with weak indications of copper-gold mineralization in the North-East anomaly. During the later half of 1989, four core holes were drilled into the shallower northern partofthe North-East anomalywhere previous drilling had outlined economic intersections of mineralization. These holes encountered high-grade copper-gold mineralization confirming the potential for an economic deposit to be hosted within the ironstone sequence. Further drilling involving over 400 holes (100 kilometres of drilling) has brought the deposit up to its present resource status.The current resource inventory is 36 million tonnes grading 2.0% copper and 1.0 grams pertonne gold and includes a high-grade zone of 13 million tonnes grading 3.6% copper and 1.5 grams per tonne gold. The discovery of this potential economic mineralization resulted from a persistent exploration effort based on indications that a large mineralizing system existed within a sequence of ironstones.

Jan 1, 1993