Search Documents

By Toffeg A. N, Abdul-Hameed I

More than 1000 Ian of seismic reflection data correlated to ten exploration wells along with geological, gravity and magnetic data are used to construct the subsurface structure, in particular the crystalline basement, along a corridor approximately 100 Ian wide that traverses central Iraq in SE-NW direction for a distance of about 500 km from Baghdad in the central part of Iraq to Dohuk near the Turkish border. This transect is one of few such transects that represents the Iraqi contribution to the Global Geoscience Transects (GGT) project. The transect crosses two out of three major tectonic elements of Iraq: the unfolded zone and the folded zone.

Jan 1, 1990

Two recently published studies have considered whether and how robots, which have been designed for manufacturing applications, could find use in mining. The conclusions of both studies, if not identical, are compatible. Automation of mining activities will continue. Robots, at least in the short term, will have little application in mining. However, robotic concepts, both hardware and software, are of considerable relevance to mining automation, and can be anticipated to diffuse gradually into mine environments. The present paper is intended to convey the current state of thought on this subject to IFAC Symposium participants who may be unfamiliar with the referenced studies, and is not intended to report previously unpublished research.

Jan 1, 1985

By Morland R, Peck R

The Joint Committee of The Australasian Institute of Mining and Metallurgy (AusIMM) and the Australian Mining Industry Council (AMIC) have published a Code for the Reporting of Identified Mineral Resources and Ore Reserves. The Code is the result of an initiative begun in 1971 to achieve industry self regulation of Resources and Ore Reserves reporting which resulted first in guidelines for reporting standards but which have now been incorporated in ASX Listing Rules as a Code with significant sanctions ensuring compliance. This paper describes the background to the Code, its key provisions, and comments on practical aspects of working with the Code and compliance issues.

Jan 1, 1990

The article presents methods of testing and recording of water amount pumped out in surface mining. The authors describe necessary recommendations how to carry out measurements so that one can separate the surface run-off and groundwater inflow from the total inflow. They demonstrate methods of evaluation of these kinds of inflow in open pits when water amount testing is carried out every eight and 24 hours as well as simple methods when only monthly records of water are available. The authors also describe procedures for evaluating the water inflow when an open pit is dewatered gravitationally and measurements in discharge channels are irregularly carried out.

Jan 1, 2003

To carry out its responsibilities the SECV needs to manage the visual environment effectively. Every land oriented decision effects what we see and the value in pursuing visual excellence is supported by informed opinion, widespread community interest and evidence of cost- effectiveness.By knowing how we perceive the landscape and then changing or conserving it we can assist in fostering a positive mental image of a countyside which is welcomed by the local and regional community.It is useful to examine key design elements and the value we place on visual impressions in relation to three significant SECV rehabilitation projects, at Loy Yang, Newport and Morwell Open Cut.

Jan 1, 1992

This paper discusses considerations to be made for the selection of rock tunnelling machines, as opposed to drilling and blasting. A systematic approach is presented in terms of utilizing data frcm site investigations to accurately forecast machine performance for estimating and planning purposes and to help minimise associated risks. Useful rock index properties are identified, and correlations for predicting advance rates for roadheader and full face machines are presented together with a simple method of characteristing rock mass conditions for estimating machine utilization and the savings to be gained in support costs. Finally considerations for tunnelling in adverse ground, for advance probing and for large sized tunnels are outlined.

Jan 1, 1987

The Argyle Diamond Mine came on stream late in 1985 as the world's largest diamond producer in terms of carat output. The design of the process plant, including the heavy medium separation (HMS) facility which provides the initial stages for separation of diamonds from gangue, evolved over a lengthy period of feasibility study and site investigation into the final form described in this paper. The commissioning was carefully planned and co-ordinated, and culminated successfully with handover of the plant on schedule and within budget. Problems encountered during .within were minimal and since then the plant has achieved greater than design throughput during its first year of operation. Darvr_ontmn

Jan 1, 1987

By Milner E. F

Thallium is largely volatilized during sintering in the conventional sinter/blast furnace production of lead. The new direct oxygen smelting processes will force the thallium into the bullion, necessitating a means of removal to avoid contamination of the refined lead. Pilot plant testwork demonstrated that thallium was efficiently removed from lead bullion by treatment with molten zinc chloride. The spent zinc chloride salt was treated in the laboratory to recover lead sulphate, a zinc chloride solution, and a thallous chloride salt containing over 80% thallium. Cominco is installing this thallium process as part of its Trail Lead Smelter Modernization Program which will commission a QSL bath smelter in late 1989.

Jan 1, 1989

Opencast blasting is notoriously subject to variable blasting conditions, some of which are related to changes in ground conditions and some to human and equipment factors. As drilling and blasting constitute a high proportion of working costs, control in this area is crucial for good management. During a recent exercise, wireline logging of blastholes was shown to have the potential to provide invaluable data for optimising blasting control and design. The paper reports on the exercise undertaken, showing that serious misconceptions as to the borehole diameters, explosive densities and posi- tions of decking were quickly corrected using the method. Potential use in blast design is discussed, as are the cost implications.

Jan 1, 1988

The impulsive loading tests under confining pressure were performed to investigate the dynamic fracture properties of rocks in a triaxial stress state. The apparatus in this study consists of the Split Hopkinson pressure bar, a pressure vessel and hydraulic actuator. Magnetite-quartzite and limestone were selected for the test. The stress-strain curves and fracture strength under confining pressure obtaind in the tests were compared with those of the conventional triaxial tests. Finally it is concluded that on the effect of dynamic that on the effect of dynamic compressive strength of rock, dynamic elastic coefficient of rock and confining pressure etc. on the blasting result

Jan 1, 1990

By Windsor C. R, Thompson A, Bywater S

A new high tensile strength, steel cable, that may be grouted into boreholes has been developed for use as rode reinforcement. The manufacturing technique produces a birdcage pattern in which the cross section varies along the length of the cable. The load transfer from cement grouts to birdcage cables has been demonstrated in laboratory tests to be better than that of standard 15.2 mm diameter seven wire cables. The manufacturing process also allows for a wide range of capacities which may be specified by design engineers. The various birdcage cable configurations have been applied as rock reinforcement in a number of Australian underground and surface mines.

Jan 1, 1990

The Kidston Gold Mine i s located in northern Queensland some 2 Ukm northwest of Townsville. I t is the largest gold mine in Australia and produces approximately 25 percent of Australia's gold and one percent of the world's gold.Initially, traditional mining industry management approaches resulted in the rejection of what appeared to be an attractive low-grade deposit as an uneconomic proposition. Critical re-examination revealed that the rejection was based upon managerial inflexibility and traditionally over-conservative methods of mine evaluation, construction, operation, projected commodity prices and contingency factors. "Ihus it tradition was to prevail, the Kidston prospect would never have been realised.

Jan 1, 1985

The Jurassic Walloon Coal Measures crop out over much of the Moreton Basin and contain numerous thin, banded coal seams which have been mined at various locations since the 1870s. Historically most mining has been by underground methods. Increased exploration during the 1970s and 1980s has led to the delineation of significant open cut coal resources and to the development of the Oakleigh, Jeebropillly and Ebenezer open cut coal mines in the Rosewood-Walloon area. Over 2 170 million tonnes in-situ of shallow, high volatile bituminous coal with a mean maximum vitrinite reflectance of between 0.5 and 0.6 have been proven in the Basin.

Jan 1, 1991

By Estoque J, Abaigar J, Domingo B, Acenas M

The Siana gold-silver deposit of Surigao del Norte, Mindanao, Philippines is perhaps one of the most complex in the world, being related to an ancient suture zone known as the Philippine Fault. Early accounts described the deposit as epithermal, consisting of an upper limestone replacement orebody and a lower vein type deposit hosted in andesite. Recent field and laboratory studies, in correlation with the latest findings on the archipelago's tectonic evolution, however, led to the present interpretation of the Siana ore deposit's origin as involving both syngenetic and epigenetic processes, with limestone breccia, similar to the Cow Head Breccia of Newfoundland, as the principal host to mineralization.

Jan 1, 1987

THE filter-press, which has done so much for the successful-treatment of the sulpho-telluride ores of Kalgoorlie, has a serious rival in the vacuum process, and this paper is written with a view to arousing more interest in the cheaper working of the press, it being doubtful whether its efficiency in extraction can be improved upon. Before proceeding with the actual working of the press, it may be as well to make brief mention of the character of the ore treated at the Associated Northern Blocks, where these notes were compiled. A sample from several weeks' run was taken of the raw ore, with the following analysis...

Jan 1, 1911

By Wright J

Large scale cut and fill mining in narrow silver-lead-zinc orebodies began at Mount Isa in 1964. Initially each orebody was one stope and access was via raises from the level above. Upholing was the principal mining method, although flatbacking was employed where ground conditions were more difficult. Developments since have included access via footwall inclines and connection of all stopes with major crosscuts. Flatbacking is the principal method. The most recent cut and fill operation is now fully mechanised using drilling jumbos, rockbolting jumbos and load-haul-dump units. Improved ground support and drilling and blasting practices have enhanced safety, recovery and productivity in all cut and fill operations.

Jan 1, 1988

By Komosa T, Muir D. M

Adequate levels of dissolved oxygen are essential for efficient gold dissolu- tion. The actual levels in plantpuips can be seriously reduced by the presence of oxygen consuming reactive minerals, and reduced oxygen solubility in saline water. The rate of gold dissolution is then limited by oxygen availability rather than cyanide. Ion selective electrode dissolved oxygen meters can give an effective indication of the relative oxygen saturation, but they are not able to give meaningful values of dissolved oxygen in saline water, without custom calibration curves. When the dissolved oxygen concentration is rate limiting, the addition of oxygen or peroxide can improve gold leaching kinetics as well as reduce cyanide consumption.

Jan 1, 1991

By Yan D. S

The removal of antimony from a refractory gold-bearing stibnite ore by roasting and selective chlorinating roasting was investigated. The influence of roasting temperature, roasting time, roasting atmosphere and type and amount of chlorinating agents on antimony removal were studied. The laboratory studies carried out included roasting tests of 4 g samples in a laboratory rotary kiln, followed by 400 g samples roasted in a fluidised bed. The test results revealed that antimony was efficiently removed by roasting at temperatures over 800¦C in a nitrogen atmosphere. The most efficient volatilisation of antimony was achieved with the addition of ferric chloride at temperatures between 350-600¦C.

Jan 1, 1995

Quite often the reserve assessor becomes enamored with the numbers gen- erated and forgets the basis for his assessment. The quality of the assess- ment can only be as good as the quality of the input data. The use of seismic data from the Gippsland Basin in assess- ing Esso/BHP's oil and gas reserves is an excellent example of this principle. By significantly improving the quality of seismic data, a much more reliable estimate of a field's reserve potential can be made. In addition, it provides the basis for further delineation drill- ing which, as recent experience in Gippsland has shown, often leads to increased reserves.

Jan 1, 1979

An approximate rapid design system for tunnel liners and underground structures is presented which permits the effects of structure geometry and stiffness, rock quality in terms of its deformation modulus, and the applied system loading to be entered as data to produce direct designs conforming to stress limitations, optimum reinforcement requirements and restraints on section dimensions. An 'equivalent column' concept is introduced for modelling the rock mass in contact with the structure. Only the rock treatment is given in detail but the results of sensitivity analyses, with reference to rock quality, for a typical liner design are given and these results related to a number of empirical design approaches.

Jan 1, 1976