Search Documents

This paper aims to provide some' new and original thoughts on tungsten carbide drill-bits and describe practices and performances, some of which are unique and most of which have not previously been described. Many theoretical and descriptive papers and articles on carbide bits have appeared during the last few years, and in the big majority conclusions such as these were made. These results are marked by premature failure of the bits, or The full or economic life of the bit is seldom reached due to the premature failure of the insert. Unfortunately those conclusions are seldom accompanied by the reasons for premature failure. In the few cases where reasons for failure have been advanced, very little, originality has been shown. The reasons usually given are that the failures are due to bad operators, bad workmanship, faulty steel or unsuitable machines, but it has been shown at Mount Isa that the chief reason for poor performnce is bad design.The first question asked will be, "What is wrong with the design of most bits?" and the answer'is, "The size of' the inserts". There may be many other small faults iiI different types of bit but Mount Isa experience indicates that the size of the insert is the most important factor influencing pit life. Under normal conditions it has been found, that there is a minimum size of insert that will give satisfactory performance, and this minimum is 5/16 in width and ? in. depth at the shoulder. A big majority of the bits at presentavailable in Australia do not satisfy these requirements.

Jan 1, 1953

Don Hausen was a pioneer in the field of quantitative mineralogy. Methodology that he developed at Newmont almost 40 years ago is still employed today, only the technology has advanced. Petrographic methods were stressed with an emphasis on alteration, mineralisation and paragenesis. Methodologies employed by Don on the Carlin deposit were applied to developing the Carlin Trend by helping to work out lithology and structure, which ultimately led to the discovery of deep high-grade deposits. Quantitative methods used by Don on San Manuel, Copper Creek and Superior, Arizona were applied to the development of the Batu Hijau Deposit in Indonesia. Advancements in technology since DonÆs time have made the mineralogist much more efficient. Manual measurement of peak heights off of strip charts for semiquantitative XRD has been replaced by software that does Rietveld refinement and whole pattern fitting. Hand contouring of XRD data has been replaced by digitised data incorporated into geologic models. Optical point counting, which would take a dayÆs work to process 1000 points, has been replaced by automated SEM methods where 20 000 points are possible in an hour. The use of the optical microscope remains relatively unchanged, and still remains as Don emphasised the æeyesÆ of mineral exploration. However, the information can be relayed much more quickly with digital image capture and electronic data transfer. Don insisted on becoming involved in projects at the grassroots level and supporting the project through mine closure. This made the mineralogist a liaison between exploration geologists, mine geologists, metallurgists and mine engineers. The methodology that Don helped develop continues to provide invaluable support to Newmont geologists and metallurgists worldwide today.

Jan 1, 2008

By Fabjanczyk M. W

Artificial ground support has developed into a refined science over the past 20 years. From reactive support systems such as timber props and steel supports, to active systems such as roof bolts and cable anchors, ground support technology has now developed efficient systems that work well in many instances. However this paper demonstrates that there is still a long way to go to develop optimum ground support systems. Some conventional rock bolts and cable anchors emphasise their tensile capacity only, without considering other factors such as their shear strength or shear modulus, or if the support member can transfer all of its support capacity to the surrounding rock. Examples are given of the use of ground anchors with high tensile and shear capacity in underground coal mining as well as examples of slope failures in open pits where the cable bolts have remained intact because they have been unable to transfer their full capacity to the surrounding weak rock mass. For underground coal mines, speed of installation is also of primary concern, but it must also have high tensile and shear capacity both in terms of strength and stiffness. Ground support systems of the future must therefore address these problems. An innovative new rock bolt is discussed which goes some way towards solving these problems. This new rock bolt is screwed into the rock and thus has a direct mechanical interlock with the rock. Initial field results show that it has an extremely high anchor capacity and can be fully installed in approximately 30 seconds. It has considerable capacity to improve the productivity of the coal mining industry.

Jan 1, 1992

By Grant J

In surface mining, significant improvements in efficiency can be obtained through greater control over the formation of the muckpile. By tailoring the muckpile shape and its looseness to the requirements of the excavating equipment savings can be rea- lised through increased production, machine life and reduced maintenance. For instance, one open cut coal mine has recently estimated that a 2001o improvement in its front row throw would realise $320,000/year savings in rehandle costs alone. Previously greater throw has been achieved by increasing the powder factor through increased quantity of explosive or by drill- ing a larger number of holes-both at a significant cost penalty. However a recent series of experimental blasts demonstrated that it was possible to achieve a twofold increase in the distance of throw of a single row blast by simply changing delay timing alone. The Nobel Electronic Delay Detonator was used to provide the timing flexibility and control required for a thorough study of the effect of blast timing on heave. Whilst it is well accepted that the front row of a blast dominates the extent of throw, it was also found that the profile of the blast could be significantly altered. To date, the general consensus has been that the muckpile for- mation from a blast is a function of the blast geometry, the rock type, the explosive and the initiation sequence. Typically the geometry, rock type and initiation system have a far greater impact than the explosive type. This has been demonstrated by many high speed film studies. However the extent of influence via initiation has rarely been fully evaluated, owing largely to the limited control offered by conventional detonators.

Jan 1, 1988

By D Macklin, R Hammond, T G. Blenkinsop

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Base metal sulfides at the Currawong volcanic-hosted massive sulfide deposit in the Lachlan fold belt of Victoria, south-east Australia, were formed in the late Silurian, but D2 deformation of the deposit in the Devonian Bindian orogeny was responsible for structural repetition that created the resource. The primary sulfide lenses were stacked by reverse-sense shear zones within a volcano-sedimentary sequence dominated by dacitic intrusions and turbidites. Shear zones were localised along lithological contacts, including the margins of the sulfide lenses. The competent dacitic intrusions did not fold during D2; folding was restricted to the packages of metasedimentary rocks. Overturning occurs within, but not between, the metasedimentary packages. The overall geometry of the deposit is that of a duplex, but the detailed shape does not conform to idealised duplex types, probably because of post-D2 deformation. A significant complicating factor for understanding the deposit, and for resource evaluation, is the dramatic variation in deposit geometry along strike, which may also be due to post-D2 deformation. The present day configuration of the deposit results from constructive thrust repetition of what may have been a single ore lens and destructive along-strike disruption controlled by rheology.CITATION:Blenkinsop, T G, Macklin, D and Hammond, R, 2015. Rheological controls on the geometry of the Currawong volcanic-hosted massive sulfide deposit, Lachlan fold belt, Victoria, south-east Australia, in Proceedings PACRIM 2015 Congress, pp 469–474 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Hilde TWC

Synthesis of GLORIA side-scan sonar and other geophysical data has provided morpholo- gical and tectonic details of the interaction between the Nazca and South American plates along the Peru Trench (80S-15¦S). Our analyses suggest that a new propagating rift of the Galapagos type is evolving along the Mendana Fracture Zone (MFZ). Subduction induced rift- ing of the Nazca plate is accompanied by organized seafloor spreading for the last 3 Ma at least. GLORIA sonographs and bathymetric mapping show an 8-10¦ divergence in MFZ width towards the Peru Trench. The fracture zone comprises numerous ridges and troughs and a lack of sediment cover in the axial part. Young magnetic lineations (anomalies 1-2A) are observed within the fracture zone wni.cn are orthogonal to the older Nazca plate lineations. The central anomaly narrows west- ward and can be observed up to 400 km seaward of the trench whereas anomaly 2A is terminated about 200 km from the trench axis. Recent SeaMARC II sonar mapping in the region shows large igneous blocks in the Trench axis to the north of MFZ but absent to the south. We believe these blocks represent young seafloor of MFZ rift/spreading center broken off from the ridges as they subduct along the Peru Trench. The MFZ rift is propagating west- ward at a rate of 115 km/Ma (25 km/Ma relative to the South American plate). Given the present rates of accretion at the East Pacific Rise and of propagation along MFZ rift, the Nazca plate will be divided into two parts in about 35 Ma.

Jan 1, 1987

By G Billing a, D Gribble, E Hall, D Varga

The theoretical benefits of electronic detonators have been reasonably well documented. To support this, a practical comparison was made between the performance of the standard shock tube system, NONEL, and a high precision electronic system, HotShotÖ, at the Sunrise Dam Gold Mine. The expected benefits from electronic detonators to Sunrise Dam were identified prior to the trial. Based on these, a number of objectives were set to demonstrate the value of the HotShot system. These are an improvement in fragmentation leading to an increase in productivity, less oversize rehandling, increased throughput and more uniformity in muck pile movement. To maintain the integrity of the trial, the nominal timing of the shots was kept exactly the same, thereby restricting any performance improvements to the precision of the electronics. Accordingly, adjacent shots were chosen with consistent geology. Video footage was taken of the blasts and vibration monitoring was carried out by fixed geophones throughout the mine. Spot heights of the muck pile swell were taken immediately after the blast and heave profile graphs were generated for comparison. Video footage was taken for a period of three hours for both shots to analyse cycle times of the excavator and trucks. PITRAM data was also collected for analysis. As far as practicable, the ore was taken to the same finger on the run-of-mine (ROM) pad to assist in single sourcing for the crusher and to allow oversize to be separated out. From specific metrics taken during the trials, it was shown that the expected improvements due to the high precision timing of electronics were realised in all areas.

Jan 1, 2007

By C Hertle

GHD-Black & Veatch (GHD-BV) have completed design and specification of the ash thickening plant at Tarong Power Station, including operation of a pilot plant. Construction of the plant is in progress and commissioning is planned for early-2004. The objective of the new plant is to convert the low concentration (lean phase) ash slurry currently generated by the power station into concentrated slurry which will then be pumped to the existing ash dam. Water recovered from the lean slurry will be returned to the power station for reuse. The drivers behind this project are to extend the life of the ash dam and to reduce water pumping costs. A maximum flow of 1000 litres per second is expected in the thickening plant. The process involves a screening phase, which removes large material that could cause blockages or equipment damage. A 50 metre diameter thickener then concentrates the screened lean ash slurry to 55 - 60 per cent w/w solids. In addition, the thickener plant will allow the harvesting of floating cenospheres (hollow, spherical ash particles) from the lean slurry. Cenospheres are currently collected from the surface of the ash dam and drained on a pad adjacent to the dam. The new system will use a surface skimmer to remove the cenospheres from the thickener and transfer them to settling ponds for further classification. The settling ponds simulate the detention on the existing ash dam, and allow entrained fine ash and slow settling cenospheres time to settle. As settling occurs in ponds, the slow settling cenospheres can be completely recovered whereas when they settle in the dam, the opportunity for recovery is lost. Cenospheres are a valuable by-product produced during the combustion process, and recycling of this material reduces the waste generated by the power station. Water recovered from the thickener drains to a three megalitre reservoir. Water is drawn from the reservoir for thickener plant service water and various other uses in the power station. The bulk of the water is used to sluice ash from the power station to the thickening plant. In the current configuration, surface water from the ash dam is reused but must be pumped several kilometres back up to the power station. The dam also holds an inventory of several thousand megalitres of water and has significant evaporative losses. Therefore the current raw water make up demand is substantial. In addition, some areas of the power station traditionally using raw water will be modified as part of this project to allow the use of recovered water, further reducing the raw water demand. The design incorporates many features of sustainable water management. By more effectively recovering water from the lean ash slurry, the amount of raw water make up required by the system will be significantly reduced. This method of water recovery provides a more sustainable and energy efficient ash-transport mechanism.

Jan 1, 2003

By S Tyrrell, B Jackson, K Matson

Northern Star Resources Limited Jundee Gold Mine in Western Australia operates a comminution circuit that consists of a primary crusher, 3.85 MW semi-autogenous grinding (SAG) mill, 1.8 MW ball mill and pebble recycle crusher. In 2017, a secondary crushing circuit was installed to remove the SAG mill throughput bottleneck and increase production of highly competent underground ore from 1.35 to a minimum of 1.7 Mt/a.This paper discusses the findings from the trial phase, the circuit design, project delivery, site optimisation, and the plant performance.CITATION:Matson, K, Tyrrell, S and Jackson, B, 2018. The application of secondary crushing at the Jundee gold mine, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 485–496 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Stevak D, Plesingerova B, Ellias K, Tkacova K

This paper presents information on the processing of minerals by decrepitation that can be an integral part of their mineral dressing. In the case of carbonates, processing by decrepitation is a special operation that has its objective as concentration of the oxide. Selective fragmentation of magnesite brought about by decrepitation uses pseudomorphosis which was observed at thermal decomposition of carbonates. By decrepitation of magnesite high-grade MgO concentrates were obtained with MgO contents above 80 per cent. With the sideritic ores a very important phenomenon was observed consisting in the removal of quartz in the fragmented fine-grained product which favourably affect pelletisation of the fines. The selective concentration of the MgO product brought about by thermal decomposition of dolomite accompanied with decrepitation was negligible.

Jan 1, 1993

This session comprises six papers: One paper is specifically on advances in drilling techniques, a paper presents a classification for water inrush rich with corresponding guidelines for protection, two papers are concerned with mining impacts in integrated catchment management - one from the quality viewpoint and the other from the quality viewpoint, and the final two papers are case studies of mine dewatering - one for an underground mine threatened by a karst limestone aquifer and the other of an open-cut mine threatened by interbedded sand aquifers. The paper entitled, Practical mine dewatering by means of surface drilled wells by Sides is innovative in presenting the case for wells as cost effective and appropriate for a number of purposes including exploration, re-opening old mines, dewatering, grout emplacement and monitoring.

Jan 1, 1988

An asymmetrical floating point Array Processor is a special-purpose Scientific Computer which operates under asymmetrical control of a host Computer. Although an Array Processor can receive fixed point input and produce fixed point output, its primary mode of operation is floating point. The first generation of Array Processors was oriented towards time series information. The next generation of Array Processors has proved much more versatile and their applicability ranges from Petroleum Reservoir simulation to speech synthesis. Array Processors are becoming commonplace in Mining, the primary usage being construct- ion of grids - by usual methods or by Kriging. The Australian Mining community is among the world's leaders in regard to computer-assisted Exploration and Exploitation Systems. Part of this leadership role must be providing guidance to Computer vendors in regard to current and future requirements.

Jan 1, 1983

By M Maslowski, J B. Gemmell, D R. Cooke, C Zesati, J Castorena

The Palmarejo, Guadalupe and La Patria Silver-Gold epithermal vein deposits occur in south-westernChihuahua state, Mexico. The veins are hosted in a volcano-sedimentary sequence that comprises andesitic to basaltic resedimented volcaniclastic rocks, together with less abundant coherent and pyroclastic facies and minor red-beds. The host sequence is part of the Lower Volcanic Series, and formed in a magmatic arc environment during the Late Cretaceous to Early Tertiary Laramide Orogeny. The Lower Volcanic Series is overlain unconformably by an extensive sequence of Miocene rhyolitic ignimbrites, known as the Upper Volcanic Series. At this time, it is uncertain whether epithermal mineralisation was related to andesitic intrusions (85 Ma) and/or Oligocene rhyolitic dykes (25 Ma). An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

Asarco's newest concentrator near Troy, Montana, began operation in October 1981, and is presently milling ore at its design capacity of 7,710 metric tonnes per day. The underground room-and-pillar mine produces a readily floatable copper sulfide- native silver ore in a quartzite gangue. Major sulfide minerals are bornite and chalcocite with minor chalcopyrite; fine grained native silver occurs with the copper sulfides. There are also minor amounts of native copper and copper oxides in the ore. A rougher copper-silver concentrate is floated, reground and cleaned twice. Cleaner tail is scavenged, and the scavenger concen- trate is combined with rougher concentrate for regrinding. Rougher flotation tailing and scavenger tailing make up final mill tailing which is disposed of by spigotting into a tailing dam located 10.5 km from the mill site.

Jan 1, 1978

Self Advancing or "Poweredtt supports are a successful means of supporting roof and designs have reached the stage where adequate support capa- bility is available for all conditions. Some designs have resulted in equipment being too difficult to transport underground and too complex to maintain. Current trends are reducing those problems and simplicity in hydraulic systems is now the keynote of both supplier and user. There is a good possibility that the "Shield-Chock" support will be the universal design of the future. So-called t'shortwall supports" have been developed to the point where they can be applied with a high degree of confidence to conditions of great variety. Develop- ments by manufacturers and practices of users related to maintenance should result in consistent achievement of designed performance.

Jan 1, 1974

By M L. Habner, S D. Munro

In a gold CIP/CIL circuit, adding new circuit water to a final tails thickener and then directing the thickener overflow to the head of the circuit significantly reduces the cyanide concentration at the TSF discharge spigot. The new water is used to dilute the final tails. The dilution and recycle of the tails in this manner may have the added benefit of reducing reagent consumption, in some cases to the point where the reagent savings justify the expenditure and Cyanide Code compliance is achieved at no extra cost. Potential circuit configurations and water recycles can be modelled by splicing a flowsheeting and thermodynamics package, such that changes to the composition of the water can be reduced to chemical speciation with a Gibbs free energy minimisation enabling a complete understanding of the circuit water chemistry.

Jan 1, 2007

By J J. Cilliers

The aim of this paper is to give an overview of the FrothSim flotation simulator and to demonstrate its ability to predict the performance of real flotation circuits. Example simulations are presented in which the feed rate to the circuit is varied, followed by simulations in which a cleaner section and recycle loop are added to the rougher bank.The simulator is able to predict both the recovery and the grade produced by the cells at all locations in a circuit and the simulator is shown to produce plausible grade recovery curves. It also demonstrated that the performance of banks of cells improve as the feed rate to the bank increased (improved grade for a given recovery), but that more cells are required to give the same overall recovery.

Jan 1, 2005

By Angove JE, Johnson GD

Sulphide concentrates are produced in a wide range of mineral processing operations. In the case of base metals they are further treated by smelting and/or hydrometallurgical techniques. In the case of refractory gold ores, sulphide concentrates containing gold are roasted or oxidised by various hydrometallurgical processes. This paper discusses the development of the Activox(R) Process which can provide an alternative method for treating sulphide concentrates. This process consists of fine or ultra-fine milling, followed by mild pressure oxidation to produce solutions of base metals or to liberate refractory gold. Base metal solutions (eg of nickel and cobalt) can be further processed by solvent extraction and electrowinning, while refractory gold can be recovered by cyanidation. The economics of the Activox(R) Process are often better than alternative oxidation techniques.

Jan 1, 1993

By Mills JC, Belcher CB

X-ray fluorescence spectrometry is used videly for routine quality control of the mining, )lending and agglomeration of iron ores. Most )f the procedures used, cannot tolerate significant changes in matrix composition or be Lpplied to a wide range of elements. Accord- ngly, a graphite briquette technique which is Lpplicable to some fifty elements in widely Tarying iron ore matrices is described. The ignificant advantages are suitability of the ame preparation for both optical emission and -ray spectrometry, a complete elemental overage for the range 5bcg/g to 100%, and the recision and accuracy of the methods are om.parable with the standard chemical.methods hich have been superseded in the authors' boratories. The proposed methods become ore attractive and economical as more prehensive information is sought.

Jan 1, 1975

Although technology and circumstances are in a constant state of change, the principles of managing the human element remain constant. The isolated mining community continues to form the backbone of the minerals industry but the nature of the isolation, along with the economic and political environment of the industry, is changing. These changes require new inputs by management to the workforce. Management must determine an effective working relationship with unions on its mine site and concurrently contribute to the build- up of the expertise of the individual worker through training and communication. It must also retain a proper balance, by way of human contribution, in cost and information reporting and in other areas amenable to computerisation. These comprise the aids to management necessary to achieve the desired operating efficiency and profitability.

Jan 1, 1980