Search Documents

By T J. Grandfield

Paste fill has been used successfully at Henty Gold Mine for the past five years. It has allowed 100 per cent extraction of the orebody, stabilised poor ground and enabled wide sections and offsets to be mined safely. However, there are a number of inefficiencies in the current paste fill system. These include the low output from the drum filter, the addition of aggregate to the paste to compensate and the trucking of paste from the plant to the portal. These inefficiencies have increased the operating cost of the paste fill system and caused a number of operational challenges such as blockages and increased pipe wear. These challenges have been partly overcome by taking ownership of the paste fill process, improved quality control and better communication. Henty is currently developing two new orebodies, the Mt Julia and the Darwin and has an opportunity to build an efficient paste fill operation. This is likely to be a high density paste system without aggregate, either located above the new orebodies or located at the plant and pumped to the new site.

Jan 1, 2002

By A R. Bonani, M P. Pe±a

The optimisation of slope angles, that is to say, increasing them, compared to the original design is always the subject of analysis of stability for geotechnical engineers and economic analysis for planning engineers. Questions to be answered include: What is the acceptable risk? What factor of safety? What probability of failure or reliability? The Rosario Open Pit has a history of failure, poor quality rocks and high pore pressures. It was decided to deepen the pit below the programmed design to test the practicality of different design approaches, which if successful, could be used to improve the economics of mining at Collahuasi. The revised slope design has factors of safety in the range of 1.0 to 1.2, probabilities of failure of ten to 38 per cent, and increased slope angles of between 3¦ and 5¦ with respect to the original design. The pit deepening with these design slopes will deliver an extra two million tonnes of ore which will have a significant positive impact on mining economics.

Jan 1, 2007

The building is a lofty, well-ventilated one of hardwood frame, with galvanized-iron walls and roof, and consists of five spans running north and south, covering a total length of 236 ft. Each span is composed of nine bays of 1:3-ft. centres, making the total width of the building 117 ft. The refinery is situated conveniently at a distance of 100 yds from the smelters. Through the third span of the building runs a 5-ton electric overhead travelling crane, of a 3-motor type, with a span of 29 ft. The crane runway extends over a railway line, which connects the smelters to the refinery. This crane is llsed for handling bullion, coal, melting kettles, lead pumps, &c. A 3-ton crane of similar type, but with a 50-ft. span, runs through the fifth span of the building and also extends over the railwav line alreadv mentioned. This crane is used to load the soft lead into railway trucks, or to stack lead awaiting shipment in the area covered by the crane's operations.

Jan 1, 1918

By B Tessier

Checking the quality of a blast may be considered as subjective. Checking this quality will require measuring objective parameters. One of them is the resulting fragmentation of the blasted product. Numerous fragmentation æmeasuringÆ systems have been developed and marketed, based on image-processing. This presentation of FragScan will illustrate advantages and difficulties when using such a system. FragScan is essentially defending a policy of large and representative sampling. The purpose is to show how fragmentation is discriminating both productivity and profit of quarry operations on a blast-by blast basis. The next step will then be to ædriveÆ the blasting process to reach a æbetterÆ fragmentation. Other applications require the fragmentation as an essential result: this is the case for large boulders used in structure-reinforcement. Several case-studies have shown that FragScan can be used for quality-control, checking size-distribution of the product according to the requirements of the end-user. Only clear thinking about the precise use of such a æmeasurementÆ will further the success of this task.

Jan 1, 2001

By A Morris

The Express Rail Link (XRL) will provide high-speed rail services from Hong Kong to Guangzhou and a connection to the national high-speed passenger rail network serving major cities throughout Mainland, China. The HK$ 67 B (NZ$ 11.5 Billion) project is of great strategic importance for Hong Kong and is being implemented to a very tight schedule, from early 2010 with completion targeted for 2015.The works include a 15 platform terminus station in West Kowloon, 26 km of twin track tunnels from the terminus to the Hong Kong/Shenzhen boundary at Mai Po, tunnel vent shafts/adits/emergency rescue siding and a stabling siding facility. Trains on the Hong Kong section are intended to operate at speed up to 200 km per hour and up to 350 km per hour on the Mainland section.This presentation will provide an overview of the entire XRL project, with a focus on the challenging geotechnical and spatial constraints on the tunnel works. This is an abstract only. No paper was prepared for this abstract.

Mar 8, 2011

By Borsaru M, Wylie AW

A neutron irradiation technique has been developed which is suitable for the determinat- ion of the iron and aluminium content of iron ore fines (-6 mm particle size) on a moving rubber conveyor belt. The determination of iron entails measure- ment with a NaI(Tl) gamma ray detector of the characteristic prompt gamma rays (7.64 MeV) due to thermal neutron capture in iron, while the determination of aluminium is based on thermal neutron activation analysis. For the latter a second detector must be placed down- stream to monitor the 1.78 MeV gamma radiation emitted after activation of aluminium. Although conveyor speed has no effect on the Fe measurement, it has an adverse influence on the aluminium signal, and the belt speed should not exceed 0.1 m/s if good accuracy is required. Static trials on a 460 mm rubber conveyor belt with constant ore geometry indicate that for iron an accuracy of ¦ 1.2% Fe (2a) can be achieved for crushed run-of-mine ore at

Jan 1, 1978

By Boyack DJ

DEFINING AN ECONOMIC TARGETExploration usually begins with the corporate goal of finding a minimum tonnage and grade of a selected mineral. Sometimes this is expressed more simply as a minimum quantity of contained metal without any indication of the desired grade or implied profitability. Such a goal is useful in the selection of exploration areas and the planning of initial drilling programs. However, it should be reviewed as soon as significant mineralisation has been identified. To make rational decisions about exploration expenditure, the potential return from a deposit must be estimated from the outset and re-esti-mated frequently.The potential return will depend on:1. The proportion of mineral which can be economically recovered from the deposit by mining (the mining recovery).2. The quantity of valuable constituent that can be recovered after dilution with waste rock during mining and losses due to incomplete metallurgical recovery.3. Expectations of price and markets.4. Capital and operating costs applying to the selected mining and processing methods, and to transportation and marketing. Increasingly, environmental costs and constraints must also be considered.

Jan 1, 1990

By M Roche, W J. Huxley

Finding a balance between practical and acceptable groundwater management, and providing for the needs and impacts of mining developments remains a challenge. The changes that accompanied the recent implementation of water reforms have provided greater flexibility for the water manager and greater certainty for the resource user. However uncertainty associated with understanding of complex aquifer systems, balanced against providing for the needs of mining developments, the rights of existing water resource users and expectations of the broader community have not diminished the conflicting issues faced by water resource managers and resource developers. Licensing under the Water Act 2000 provides the regulatory link with the taking of water for water supply purposes or as a consequence of the mining activity. This paper outlines key elements of sustainable water resource management involving certainty of access to water and adaptive environmental management that are delivered through conditioning the water licences issued for the particular mining development. Implementation of this approach is illustrated through a case study involving the BHP Billiton Cannington Mine in North West Queensland.

Jan 1, 2003

The mining industry has a well deserved reputation earned over the years for innovation, engineering, management and the quick application to mining of emerging technology. The cumulative result is the economic exploitation of lower grade resources. The developments during the last decade have done nothing to tarnish the reputation. There are many that come easily to mind: the use of contractors for both surface and underground operations, a trend toward mine management contracts, the increasing recognition of the economic potential of ground support, and the development of physical measures to achieve it, - sophisticated measures to analyse blasting , and thus improve fragmentation, - instrumentation to assist geotechnical appraisal, - the development and application of the powerful and flexible, excavator, - the evolution of measures to improve grade control, - massive improvements in equipment productivity and reliability built largely around the application of hydraulics, - the development of powerful computer packages for orebody modelling, mine design and extraction, - simple "dense" fill systems, - maintenance management techniques including the greater use of off-site maintenance of exchange components, - the utilisation of communication systems for data transfer.

Jan 1, 1989

By C Gormley, G Lane, J Kwak, A Hopkins

Complex processing plants present a myriad of safety issues to the design engineer. The extent to which the design engineer manages to lay the foundations for a safe plant ultimately sets the stage for life long safety performance. Industry traditionally measures engineering safety performance by indicators such as Lost Time Injuries, Restricted Work Case Injuries, Overall Incident Frequency Rates, etc. While these measures are useful indicators of performance for the construction, commissioning and operations phase of a project, they do not necessarily drive the most appropriate behaviours for Safe Plant Design. Achieving an inherently safe design requires a diligent focus on low frequency, high consequence events. First and foremost the engineering team needs to have a design culture and methodology which leads to a plant which is as close as possible to being inherently safe. Such a culture might come from an organisation that has æmindfulnessÆ about safety, and which is nurturing a culture where warning signs are recognised and addressed. This paper explores the development of mindfulness and warning signs in design.

Jan 1, 2004

By R Witt, M Lowing

Tanking of tunnels is now often specified when inflows exceed as little as 1 L/s/km with a unit distance of 100 m. To demonstrate inflows over a 100 m segment of a tunnel are less than 0.1 L/s with a standard error of 0.01 L/s by timed, gravity filled, volume measurement up and downstream of the segment, the measuring cylinder volume (L) must exceed 10 Q, where Q is the flow in L/s, and the number measurements taken and averaged must exceed 20 . If a standard error of 0.02 L/s is acceptable then 5Q2 measurements must be taken and averaged. If gravity filling is not possible then the number, n, of repeat pumped container measurement required is given by: where: is the 100 m section leakage is the volume filling time is the standard error of volume measurementZ is the standard normal variateK is a coefficient dependent on physical measurement conditions Based on analysis of field data an indicative coefficient of variation of volume measurement is ~0.05.

Jan 1, 2008

From December 1994 to November 1997 Odin MiningÆs Estero Hondo alluvial gold mine in western Ecuador washed almost 3.2 million bank cubic metres of gravel to produce just over 2600 kilograms of pure gold at a recovered grade of about 0.8 grams per bank cubic metre. The operation was a simple open pit. Draglines stripped the overburden, backhoes mined the gravel, and trucks transported the ore to a stationary, gravity-based wash plant for processing. At start-up the planned throughput was 55 000 bank cubic metres/month, but a year later this had been increased to 100 000 bank cubic metres/month. From April 1993 to July 1997 a total of 440 churn drill holes and 15 pits were sunk to test the property. The methods used to prepare the resource and reserve estimates from the raw field data are described, and seven sets of completed estimates are used to track the evolution of the projectÆs resource/reserve base through the exploration, feasibility and production stages.

Jan 1, 2003

By Bilbrey J. H

Land utitized duxting the past 45 yeans by the mining industty in the United States con all puxpos ez to tal4 neatly 4 million sexes. Ob this axes, 13 pexeent is used bon dL4posal ob bLne -sized mtinexal wastes dL4eaxded by one milling plants. These wastes, especi- ally the inactive taLeLng4 ponds, xequixe some type ob stabULzation to pxevent aix and watex pollution. Because these tailings ponds axe locat- ed undex wideey vaxyting etLmctLe conditions and thetix physical and chemi- cal ehaxactexti5tLes axe not constant, many methods have been developed by the Fedexal Buxeau ob Mines and oXhex inve4- ttigatoxs box 4tabLtLzLng taLtLngs. This papex detfnea.e4 the magnitude ob the pxoblemz associated with the xeelametLon ob milling plant wastes and discusses the vaxtious methods that have been developed and used. Data bxom selected Buxeau o4 Mines taboxato&y xeseaxch pxojects and a s.abAJLzetLon field txtial axe pxesen.ed.

Jan 1, 1976

By P Allum

This paper presents a case study to reduce the operational cost on the secondary ball mill circuit in the Lead/Zinc Concentrator at Mount Isa Mines. The circuit includes two five-metre diameter ball mills each closed with a cluster of ten 15-inch cyclones. The operating cost for both ball mills is about six million Australian dollars per annum.The concentrator achieves 75 per cent of the plant design capacity with one ball mill operating, but will have to use two ball mills when 100 per cent plant capacity is required. The optimisation study on the circuit identified a new flowsheet that enabled the concentrator to reach 100 per cent of the capacity by using one of the two secondary ball mills. The success of the project utilised the existing equipment rationally and saved the operational cost for one ball mill at full concentrator capacity. A further simplified secondary circuit is proposed using the IsaMill for the secondary grinding duty. Performance of the IsaMill circuit and the potential cost savings are predicted.

Jan 1, 2002

By M Devia, J Rapkoch

This paper is intended to help design engineers, operating staff and plant managers understand the principles of metallurgical gas handling systems design. It also explains operating, safety and energy savings issues that the designer should take into consideration in the design of process off-gas systems for sulfide smelters. Primary smelting reactors, converters, and other off-gas sources impose challenging duty requirements on the various components of the gas handling systems. This paper reviews the design of common system components including the hood for gas capture at the system inlet, gas conditioning, gas cleaning, ductwork, dampers, hot gas fans, and the appropriate use of instrumentation and controls. The engineer must also be aware of how ductwork system effects and heat losses influence system performance. Also, the analysis of a recently-designed gas handling system will be reviewed, which includes high-strength SO2 gas from a smelting reactor, asymmetrically located Peirce-Smith converters, and a gas mixing chamber to mix the gases before they are sent to two acid plants of different sizes.

Jan 1, 2005

By D J. Clark, S Hewson, T Li

Cadia Hill Pit is a gold copper porphyry deposit hosted in monzonite. The pit slope design is primarily based on structural controls related to faults and shears with largely massive rock masses between the structures. The slope design attempts to achieve an optimum configuration at a bench to overall scale, considering economics and safety implications against the geotechnical and structural conditions. To date the slopes have been mined at interramp angles of up to 60¦ over heights of 120 m. Limited slope and batter failures that have occurred are structurally controlled and occur rapidly. The pit-mining schedule requires concurrent mining of part of the final pit walls and the progressive interim cutbacks. Engineering and operational solutions to hazard reduction and risk management issues have been implemented wherever viable to æengineerÆ out the hazard and mitigate the risks. However, comprehensive management plans and operating procedures have also played a vital role. This paper details the management plan and the operating procedures that have been developed and implemented to mitigate the risks associated with rock falls.

Jan 1, 2003

Compared with modern longwall coal mining systems, automation has not been developed very far in the underground metal minin industry. One of the main reasons for this is that present har rock mining systems do not produce ore with a controlled degre of fragmentation. The often poor fragmentation from the stopescauses large extra costs and precludes material which 1-ends itself to automationThe paper investigates the possibility c technology for automatic loading and trapconveyor belt to a shaft dump pocket. With this concept, it will be necessary to control the maximum fragment size by careful blasting design. The degree of fragmentation will have to be finer than is common to-day. The study shows that the belt conveyor mining con-cept with controlled fragmentation may be economically competitive with conventional cyclic loading and transport, even for an annual production as low as 0.5 mill. tonnes.. Fragmentation design and cost calculations have been based on a combination of the Kuznetsov relationship between blasting parameters and mean frag-ment size, and the Rosin-Rammler formula for fragment size distribution.

Jan 1, 1985

The most frequently applied project evaluation criteria are the Net Present Value, the Internal Rate of Return, and the Pay Back Period. Unfortunately, the Internal Rate of Return and the Pay Back Period, if interpreted according to their traditional definitions, easily produce results which contradict the Net Present Value. The reasons for the Net Present Value incompatibility of the two criteria are that these criteria have not been adequately defined and so new, complete definitions are recommended. The concept of the True Rate of Return is proposed as a substitute for the interest rate that the Internal Rate of Return has been believed to represent. The redefined Internal Rate of Return and Pay Back Period criteria, as well as the True Rate of Return are all Net Present Value compatible and can, therefore, serve as independent project evaluation criteria. Also, the correct approach to the evaluation of mutually exclusive alternatives and the status of the often neglected borrowing projects in project evaluation are found to be quite important.

Jan 1, 1991

By A Purvee, M F. Lee, L J. Mollison

Oyu Tolgoi is a large Cu-Au porphyry deposit in the south Gobi desert, Mongolia. The first of several deep, large-diameter, concrete-lined shafts, Shaft 1, is nearing completion. It will have a finished depth of 1380 m at a diameter of 6.7 m. These shafts will provide access to and hoisting capacity for block caving of deep underground ore. Geotechnical site investigations, and associated predictions of stability and ground support requirements, are compared against actual construction performance. Routine mapping is essential, along with checks against predictions and informing the contractor of ground conditions and variances.Advance rates are compared against predicted rock mass quality. A reasonable correlation exists between Qwall and advance rate. Overbreak and concrete liner thickness is related to the blockiness quotient, RQD/Jn.A ætool-bagÆ of just a few support elements (chain-link mesh, fibrecrete and 2.4 m long friction anchors and resin grouted re-bar bolts) was able to cope with the ground conditions encountered. QA/QC procedures are essential from the factory, through site storage to installation.

Jan 1, 2008

Silver and gold bearing ore from the Palmarejo mine, located within the Mexican state of Chihuahua, contains a complex mix of electrum, native silver, silver sulfides and silver chlorides. This paper presents a case study that describes the selection, development and engineering of a tailored process plant for the recovery of silver and gold from this ore. Process circuit feasibility study modelling, metallurgical test work and engineering studies are outlined. Options considered to optimise the recovery of the contained silver and gold are compared, based upon cost, operability, recovery and engineering aspects. Concentration by flotation was found to be the preferred primary recovery route. Intensive leaching of the flotation concentrate resulted in solution grades sufficient to allow direct electrowinning to be evaluated against the more traditional Merrill Crowe process. The flotation tailings stream is processed through a separate leaching stage as there is sufficient economic metal extractable from this stream. The processing flow sheet, which is designed to maximise the recovery from both the flotation concentrate and tailings, and to utilise a common metal production facility, is presented.

Jan 1, 2009