Search Documents

The first thing to be aware of is that the warming effect of carbon dioxide is strongly logarithmic. Of the 3¦ that carbon dioxide contributes to the greenhouse effect, the first 20 ppm has a greater effect than the following 400 ppm. By the time we get to the current level of 384 ppm, each 100 ppm increment will produce only about 0.1¦ of warming. With atmospheric carbon dioxide rising at about 2 ppm per annum, temperature will rise at 0.1¦ every 50 years for the next couple of hundred years before the effect becomes minuscule. The warming of the 20th century, as the Earth came out of the Little Ice Age, was a consequence of short, high-amplitude solar cycles. A number of solar physicists have predicted that the next solar cycle, Solar Cycle 24, will be quite weak. Based on the correlation between solar activity and the EarthÆs climate, a temperature decline of 2¦C is predicted for the mid-latitude regions over the coming decade, equating to the experience of the Dalton Minimum. Anthropogenic warming due to carbon dioxide will not ameliorate this temperature decline. Increased atmospheric carbon dioxide is wholly beneficial due to itÆs fertilisation effect. Efforts to inhibit Australian carbon dioxide emissions are exactly wrong in science.

Jan 1, 2009

The geotechnical and environmental aspects of heap leaching are very closely tied during design, operations and closure. Potential environmental impacts from heap leaching are mostly due to land disturbance and water quality issues, including both groundwater and surface water. Water quality issues are mostly related to containment design, which is primarily a function of proper sizing of the facilities and site specific liner design. Geotechnical analyses is the dominant discipline in providing cost efficient, operationally effective and environmentally sound heap leach facility designs. Much has been published on geotechnical aspects of heap leach design, for example Van Zyl, Hutchison and Kiel (1988) and Van Zyl (1987). This paper will emphasize a few specific aspects related to the geotechnical and environmental consideration for heap leach projects. These aspects are: ò site investigation; ò containment design; ò slope stability; ò heap flow dynamics; and ò closure design. Design of a heap leach project must consider not only the operating life but also closure and post-closure considerations. As a matter of standard practice, designing for closure is an extremely important concept. Not only is it important for environmental aspects, but experience also shows that projects designed for closure will be overall more economical for the total life cycle of the project. Closure considerations are also important during project feasibility evaluations to ensure that total life cycle costs are evaluated.

Jan 1, 1994

By Sturgul J. R

A major electricity generating authority have a proposal to construct a Power Station. An understanding of the operation of the bunker system is of importance to the designers and a computer simulation model of the operation was constructed. The computer language used was GPSS/PC which is a recent form of the language designed for the per- sonal computer. The model simulated trains arriving at the power sta- tion and unloading onto conveyors which carry coal to the power station bunker. Coal was drawn from the bunker at a specified feed rate to the power station. Numerous restrictions were placed on the model, if the bunker level got too high dozers would pull coal out of the bunker onto the stockpile, and if the level got too low the dozers would push coal back into the bunker. The conveyors and dozers were unavailable due to breakdown'at various times and trains would arrive randomly about a mean interarrival time. The system was simulated for 30 years of oper- ation and the model used a basic time unit of 30 minutes so that the system was updated 525,600 times during the simulation. The results of the simu- lation gave the designers a greater understanding of the critical factors in the operation, which may now be engineered to minimise adverse Effects.

Jan 1, 1988

By A Maurer, N Pereira

Low-density explosives have been developed with trials being conducted for over 20 years and yet have still only gained limited market acceptance despite producing some very promising results. The biggest concern with industry acceptance has been disbelief that a product with lower density than the ANFO benchmark could fragment anything but the weakest of strata. Trials have been carried out with products such as diluted ANFO, low-density ammonium nitrate (AN) and various other mixes, although it has been only recently that low-density explosives have been accepted as a serious alternative to traditional products such as ANFO and heavy ANFO. The recent uptake of low-density products has been the result of several key factors: the current resources boom forcing AN supply issues, the development of new handling techniques, and a far better understanding of the utilisation of such products. This paper highlights the benefits of low-density products available in the market and focuses on the situations where low-density explosives can provide the end user with benefits that would otherwise be achieved through more time consuming methods. Through correct implementation, low-density explosives can provide the blast designer with another option when looking at the optimum method of breaking the rock. This while still controlling the other limiting factors such as cost, environmental impacts (noise, vibration, dust and fumes), coal damage and safety (stable walls).

Jan 1, 2005

By Donchak PJ, Lang SC, Hammond RL, Bultitude RJ

The Hodgkinson and Broken River Provinces form the northern part of the Tasman Orogen. They are separated by a broad belt of Late Palaeozoic igneous rocks, but were probably originally continuous. They are bounded to the west by a system of major faults (Fig. 1) which separate them from the Georgetown Province. Although largely Precambrian, the Georgetown Province includes probable Siluro- Devonian granitoids, and in the south adjacent to the Broken River Province, metamorphosed Early Palaeozoic(?) volcanics and sediments of the Greenvale Subprovince. South of the Broken River Province, the Lolworth-Ravenswood Province includes probable Precambrian rocks, Cambro-Ordovician volcanics and sediments, and voluminous Ordovician to Early Devonian granitoids. The first systematic studies of the provinces were the 1:250 000 scale mapping programs by the Bureau of Mineral Resources and Geological Survey of Queensland (White, 1965; de Keyser and Lucas, 1968). These and subsequent regional studies were reviewed by Arnold and Fawckner (1980). Remapping by the Geological Survey of Queensland since 1982, and a concurrent regional study of the deformation by Hammond (1986) have provided much new data. We acknowledge the contribution of other members of the GSQ field parties - L. Cranfield, J. Domagala, B.G. Fordham, P. Green, R. Halfpenny, R. Hegarty, L. Hutton, S. Law, D. Macansh, T. McLennan and M. Scott.

Jan 1, 1987

By Pyrih R, House A, Shangraw J, Silva AJ

Sunbeam Mining -Corporation has the inten mine with heap leach gold recovery, near spent ore indicated a relatively high ar topographical configuration, the spent across a small drainage and a lake. Du permit for spent ore disposal from th agencies, concerns about the potential contamination by the arsenic were expres conducted extensive studies to addre contamination. These studies consiste( geochemical and geotechnical parameters underlying the proposed disposal si geotechnical investigations were also hydrologic characteristics were include with the use of an IBM PC computer. :ion of opening an open pit gold Stanley, Idaho. Testing of the ?enic content. Due to the local ore was planned to be disposed :ing the process of obtaining a federal and state regulatory for surface and ground water .ed. Sunbeam Mining Corporation is the potential for arsenic of laboratory testing of both of the spent ore, and the soils te. Field hydrogeologic and -onducted. Local climatic and 1 in the analysis of these data Conclusions of studies indicated that although the seepage through the spent ore disposal would contain an elevated dissolved arsenic content, the hydrologic and geochemical characteristics of the site would prevent arsenic migration into the local ground water system. The attenuation of arsenic on soils with high clay content, and dilution after reaching the ground water table would lower the arsenic content to acceptable Concentrations.

Jan 1, 1988

By Kavetsky A

A new model of flotation is presented which allows predictive calculations of total solids flows and metal grades and recoveries to be made for industrial flowsheets. A method of making these calculations is presented and illustrated with examples. The problem of determining sufficient flotability characteristics from a sample of circuit feed to predict the behaviour of that specific ground ore in the flotation circuit (ie performing flotometric analysis) is addressed, and some suggestions are made for its solution. A feature of the flotation model is its practical technological orientation, allowing determination of a small number of ore flotability parameters by fitting observed batch kinetic flotation data. The unit model explicitly includes the cell aeration as total bubble area per unit pulp volume, and pulp residence time. Although more complex unit models are feasible, it is thought that this model is sufficiently realistic to illustrate the points made. The modelling approach is illustrated by application to flotation data from a Kambalda ickel circuit. The model is parameterised and ore flotability parameters are back-calculated from batch kinetic data. These parameters are then used to fit the observed behaviour of the industrial circuit by numerically adjusting the unit aerations. Finally, it is shown how the model may be used to predict the effect of circuit and ore changes on the circuit's technological indices.

Jan 1, 1992

Over the longer term, the adoption of new technology is an essential component in the endless tasks of reducing mining costs, improving safety and improving environmental standards. However the choice of which of the many available new technologies to adopt and which not to adopt is not easy and the price of mistakes can be very high. The most important issue for mine developers faced with making such choices is knowing whether or not a new technology has been developed to the stage where the timing is right for its adoption. A system for categorising new mining technologies is provided. It provides a basis for more easily reaching common understandings about various new technologies and the background information supplied provides an understanding of what it takes to get new technologies to the proven stage and the risks of never getting there. Wherever possible, new full-scale mine developments should not rely on unproven technologies. Approaches to handling situations where a proposed new mine development is not feasible on the basis of proven technologies are also provided. If any commitment to the use of unproven technologies is made, a guarantee of high quality development support from the supplier of that technology is essential. Several case studies of successful and unsuccessful new technology development programs at BHP are Provided.

Jan 1, 1997

By Grader F. E

A linear motor properly wound can serve as a mechanism for separating paramagnetic sulphide minerals, like pyrrhotite, from other sulphides and associated gangue minerals. The effective- ness of separation depends on the energising current of the separator, the frequency of the a.c. cycle, and the particle size of the minerals. The speed of travel of the minerals over the surface of the separator is also a function of particle size, and appears to be constant. The movement of pyrrhotite, magnetite and iron filings of comparable size fraction (150um +74pm) on the linear motor surface has been observed using a cine camera. An attempt has been made to give a theoretical basis for the movement of the particles by calculating the minimum electrical energy required to move them. Further, the rate of decay of magnetic moment of the particles has been estimated for magnetite and it has been found that sufficient residual magnetism existed in the particles after they had been exposed to the first half of an a.c. cycle for them to have like polarity with the second half of the cycle. The particles are therefore repelled from the motor surface every second half of the cycle. This repulsion due to remanent magnetism is the probable cause of particle movement over the linear meter surf, e.

Jan 1, 1980

By Amanatidis A

In this paper, the kinetics of iron precipitation as sodium jarosite from aqueous solution is investigated. The determination of the reaction mechanism is attempted based on the experimental data of iron removal as a function of time, without using the characteristics of the precipitate.Experiments at the temperature range from 50° to 95°C were carried out with initial conditions of iron concentration IQ g/L, sodium sulphate concentration 25.44 g/L, sulphuric acid concentration 3.68 g/L, pH = 1.5 and agitation rate 600 rpm. Temperature greatly and positively influences iron precipitation from the solution and this is accompanied by pH decrease. The activation energy was determined using the maximum values of the precipitation rate, which were evaluated by polynomial fitting of the sigmoidal shape experimental curves, and it was found to be 44.37 kcallmole. The determination of the rate-controll ing mechanism was based on some criteria used for the discrimination among the three probable mechanisms of precipitation (diffusion, mononuclear nucleation, polynuclear nucleation). These criteria utilise various funetions of the recovery 'a' of iron precipitated versus time, the most important of which are the chronomals. The results of the kinetic analysis procedure showed that the polynuclear nucleation growth mechanism controls the precipitation of iron as sodium jarosite. This was confirmed by the high value of activation energy, excluding diffusion as the controlling mechanism.

Jan 1, 1993

A thick sequence of alkaline intrusions and volcanic rocks underlies a Quaternary caldera on Liliir Island. The sequence is host to a still active sub-aerial hydrothermal system and associated epithermal gold mineralisation. Sub-horizontal alteration horizons exhibit progressively increasing chondrite norma-lised (La/Lu) en and (La/Sm) cn ratios from unaltered shoshonites, to the potassic alteration zone, to the argillic altera-tion zone to the advanced argillic alte-ration zone. The increasing fractionation of HEE, and especially of LHEE, up the alteration sequence is the result of de-creasing pH, temperature and alkalinity of the hydrothermal fluids with increa-sing alteration intensity. HRE3 were especially mobile in argillic and advanced argillic alteration units characterised by acid fluid conditions and large fluid volumes. Abundant Cl, S and CO2 within the hydrothermal fluids and thus abundant REE complexing agents and large fluid volumes favoured the mobility of REE during hydro-thermal alteration of the volcanic rocks and intrusions. Steam escape, mixing of the gases with groundwater and a change from a magmatic neutral chloride hydro-thermal system to a meteoric acid sulphate system was accompanied by liquid/vapour ratio changes, pronounced alkalinity, pH and temperature decreases, and fluid/rock ratio increases. This caused the mobili-sation, fractionation and deposition of PF.F.

Jan 1, 1990

By P J. Vardon, L A. van Paassen, Y Yao, A F. van Tol

Thin-lift atmospheric fine drying (AFD) is a technique used to dewater mine and oil sand tailings, which utilises both self-weight consolidation and atmospheric evaporation. The disposed layers undergo a cyclic drying and rewetting process due to precipitation and deposition of additional lifts on top of the dried layer. The current research aims to optimise the deposition process via use of a numerical model and realistic atmospheric conditions, including both periods of drying and wetting. The model is based upon water balance and includes large strain considerations. A number of material behaviours are characterised using empirical fitting curves based upon laboratory measurement of material characteristics, including both the shrinkage and water retention curves for drying and rewetting. The model is able to model multiple lifts, simulating field scale and realistic climatic conditions within timescales suitable for engineering practice (eg seconds or minutes). The model has been previously validated against controlled laboratory experiments and utilised to simulate field tests. A series of simulations are presented to illustrate the ability of the model to be used as a practical tool for the optimisation of a tailings deposition strategy.CITATION:Vardon, P J, Yao, Y, van Paassen, L A and van Tol, A F, 2015. The use of a large-strain drying and consolidation model to optimise multilift tailing deposits, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 263–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By J Koppe, J F. Costa

A fundamental error of sampling occurs when a sample is extracted from a larger mass of ore or lot. The act of sampling requires that all particles belonging to the lot have an equal chance of being extracted. This type of sampling is called unbiased sampling. The sampling equipment (herein referred to as the sampler) should be constructed with some additional mechanical characteristics to guarantee that the samples will be unbiased. Samplers, extracting increments from a continuous flow, such as a conveyor belt, collect aliquots at regular time intervals. These time intervals relate to the number of aliquots extracted from a given mass of lot, whilst passing through the continuous flow. The frequency of extractions will influence the precision or the error of the sample (integration error). Further, the ore variability influences the amount collected from the continuous flow. Normally, the sampling protocol utilised is designed for the extractions obtained from the conveyor belt, omitting any error committed during this operation, ie the error of extracting from the continuous flow. This study aims to analyse the error of sampling a continuous flow by using a variogram with added on auxiliary functions. Each different piece of material passing through the flow will exhibit a distinct temporal variogram, which should influence the frequency of the samples being extracted for each chosen sampling error. The methodology used is presented in the form of a case study from a coal processing plant.

Jan 1, 2005

At some time in the mining life of an open cut coal deposit, consideration is usually given to determine the point at which underground mining becomes an economic proposition or even necessary. This can occur anywhere from the pre-feasibility project stage to decades after commencement of mining. Options which can be considered include the extension of the life of the open cut by use of larger equipment, the utilisation of highwall mining techniques and the introduction of low capital start-up or full underground development. The primary focus is always the minimisation of the total unit cost (including capital )of clean product. The transition point at which an undergound mining operation becomes more economic than an open cut operation is not a simple evaluation and depends on many factors, particularly on the nature of the deposit itself. The main general determining factors of the transition point are related to the three factors of mining resource, the mining method that can be used and mining cost issues. Mining resource issues include geography, geotechnics, strip ratio, geology and the size of the deposit. Mining method issues include highwall mining, extending the life of an open cut, the environment, available roof support technology, product yields and the availability of appropriate workforces. The mining cost factors discussed include capital and operating costs and the impact of productivity and management. All these factors impact to a varying extent on the transition point.

Jan 1, 1997

By Umetsu Y, Su Qing-quan

The electrical conductivity of electrolytes is very important in metal electrowinning and electrorefining processes as it has a very large influence on the energy consumption. There are few measurements of the electrical conductivity of zinc electrowinning electrolytes available. The electrical conductivity of zinc electrowinning electrolytes were measured over the following range of concentrations, 100 to 200 g/L H2SO4, 0 to 80 g/L Zn and 0 to 20 g/L Mg, at temperatures from 25 to 60 C. The specific conductivity of zinc electrowinning electrolytes may be expressed as a function of concentrations of sulphuric acid, zinc and magnesium and temperature by the following equation: k(S/cm) = 0.004 + 0.00115 t + 0.00282 [H2SO4] t - 0.00114 [M] t + 0.3442 [H2SO4] - 0.0451 [1-12SO4]2 - 0.1058 [M]ò[H2SO4] - 0.0224 (M] + 0.0286 [M] 2 where t is temperature (C), [H2S04](moI/L) is sulphuric acid concentration and [M](mol/L) is a sum of zinc and magnesium concentrations, ([Zn]+[Mg]). The specific conductivity of zinc electrolytes is a function of the concentrations of the hydrogen ion and free water molecule, which are calculated by taking into account the second ionisation constant of sulphuric acid and the stability- constants of zinc-sulphate and magnesium-sulphate complexes at 25 C.

Jan 1, 1993

By E Kabwe, M Karakus

Deep hard rock underground mines tend to experience high stress as such drives exhibit dynamic responses attributed to a rock burst variant (strainburst). This dynamic behaviour is difficult to predict, and every effort is made to devise the appropriate dynamic support system for its associated failure restraint. This paper outlines the back analysis and the support scheme design for an underground decline that exhibited damage from a dynamic strainburst occurrence. It employs a decline section that experienced a dynamically loaded strainburst that initiated rock fragment ejections. The procedure involves a preliminary structural analysis, a seismic intensity measure, and a rock mass simulation to determine the static stress concentration and ground support system response. The numerical simulation is conducted in FLAC3D which employs the advanced strain-softening IMASS constitutive model governed by two Hoek–Brown (HB) bounding yield surfaces. To account for the post-peak brittleness response associated with strainburst the plastic strain multiplier () is adjusted to 0.0 < < 1.0. The back-analysis shows that the occurrence was initiated by a low-intensity seismic wave that superimposed an extra stress component to the initial static stress which triggered rock fragment ejections. Additionally, the appropriate support scheme comprised of Weldmesh, Fibrecrete, static (split set) and yieldable (Kinloc) reinforcements is recommended and implemented. Thereafter, the bolt’s efficiency is evaluated based on the axial force and elongation capacities and then compared with the published bolt performance data. The evaluation results show that the maximum bolt axial force (0.1 per cent) and elongation (0.006 per cent) are below the designed capacity and rupture strain.

Nov 29, 2022

By T Walkemeyer, R Elliott, D Chang-Martin

Over the past decade, discrete element method (DEM) simulations have seen increasing adoption by the resources sector to inform the design of materials handling equipment such as transfer chutes, bins and hoppers. But, if ‘all models are wrong, but some are useful’ (Box, 1979) what approaches are available to check that a DEM simulation is useful? How to avoid garbage in equals garbage out. This work considers what properties of bulk solid flow behaviour are important to transfer chute simulation. Cohesive bulk solids (such as sticky iron ore fines) can develop sufficient strength to form a stable cohesive arch, this phenomenon is not well predicted by measurements of angle of repose. This work presents a two-part approach to the development of a useful DEM model that can be used to add value to the design and optimisation of bulk materials handling equipment. Part 1 is the calibration of not just one, but a range of material models chosen to envelope the range of anticipated materials that will be handled. This work describes the DEM simulation of a batch of direct shear cell tests to develop material models that can be measured by the same metrics routinely used to characterise the flowability of cohesive iron ore fines. Part 2 of this work describes systematic methods for validation of the transfer chute DEM simulations. The DEM model is only useful if it can adequately represent the typical problems observed within a transfer chute, such as blockages due to build-up and cohesive arching. Proper validation requires good observations. Validation examples of site observations are shown side-byside with simulations to demonstrate the adequacy of the DEM model and calibration approach. DEM simulations have the potential to add significant value by allowing engineers and designers to predict material flow-through equipment based on a range of material properties, allowing for stress testing designs and making iterative improvements.

Sep 18, 2023

By L Salvestro

Ventilation on demand (VOD) has been demonstrated to significantly reduce operating costs for ventilation fans, by reducing fan output to meet demand. The most effective method for reducing operating costs is to use variable speed drives to adjust the speed of ventilation fans as required – this achieves significantly larger power savings that damper or vane control alone.However, this mode of control will significantly increase the number of speed cycles the ventilation fans will experience. Fabricated impellers have a limited number of start stop cycles based on the materials and method of construction, and the operating stresses due to centrifugal forces. This means that fans experiencing constant or regular speed changes will experience a reduced fatiguelife compared with fans that are run at constant speed.The fatigue life of fans operated under various speeds using VOD is difficult to predict, as it is dependent on the magnitude of speed changes, and the frequency, which will be varied to meet demand. It is important to be able to estimate remaining fatigue life to assist in maintenance planning and avoid unplanned maintenance activities.This paper will review extensive VOD data on fan operating conditions from two primary mine ventilation fans. This paper will demonstrate how this data can be used to calculate accumulated fatigue and predict the remaining fatigue life, and how this compares with fixed speed or non-VOD controlled fans.The increased maintenance costs for the impellers will also be estimated, and compared to the operating cost savings using VOD, to determine if the savings outweigh the additional maintenance costs.

Oct 12, 2022

By G Sartor, A Rich, D Grimsey, R Forzatti, M White

An in-depth process model was developed for the pyrometallurgical, off-gas systems and water balance of the Kalgoorlie Nickel Smelter. This model was used to assess plant capacity with changing concentrate grades, increased throughput and tighter environmental emissions under a range of potential future operating conditions. Comparison of modelled results allowed for flow sheet optimisation across a range of metrics including sustainability, processing capacity and costs. Process modelling software, METSIM® (ver 2020.06 by METSIM International), was used to simulate the flash furnace, integrated electric slag cleaning furnace, Pierce-Smith converters, matte granulation, waste heat boiler, hot gas handling equipment, wet gas cleaning plant and acid plant. The METSIM® model was divided into three separate, yet interconnected models: metals, off-gas and water balancing. This allowed for improved modelling efficiency and traceability while minimising manual error. The METSIM® model was supported by inputs from other specialised software. Chemical thermodynamics software, FactSage™ (ver 8.2 by GTT Technologies), was used to establish relationships for the flash furnace fluxing strategy and determine the operating temperature. Arena® (ver 16.0 by Rockwell Automation), a discrete event modelling software, was used to simulate material movements within the aisle as well as Pierce-Smith converter operation, allowing for integration with upstream and downstream systems. A dynamic data exchange (DDE) was used to connect the results of each software package, interfacing through Excel® (version 4203 by Microsoft). The integration between models provided a streamlined approach to test capacity, bottlenecks, water consumption and emissions under a range of operating conditions, enabling a more robust process. Further downstream modelling techniques were used to assess mechanical equipment. METSIM® outputs provided key parameters for combustion assessments using computational fluid dynamics and finite element analysis for the furnace mechanical design.

Aug 21, 2024

By D Chalmers

After the sustained use of the GAG (Górniczy Agregat Gaśniczy) engine at a Queensland coalmine, it has raised questions as to its effectiveness as a remote firefighting tool. All firefighting apparatus have advantages and limitations, however the deployment of any apparatus must be based on its likelihood to succeed and effectively extinguish the fire or bring it under control. A recent study conducted for ACARP by researchers at UNSW has highlighted that there is more to be learned about the GAG. As coalmines are mining at greater depths and fan pressures are much greater than they were when the GAG was introduced, deploying the GAG may be a total waste ofresources and may place operators at greater risk. When the GAG unit is positioned on the surface of the mine, the pressure it generates has to overcome buoyancy of the exhaust gases and the frictional resistance of the borehole and part of the mine circuit. Buoyancy in deeper holes can lead to the GAG pressure relief system opening, venting out the products to the atmosphere without delivering any product to the mine workings. Additionally, frictional resistance is a function of distance. Deeper holes will have a greater frictional resistance than shallow holes. Delivering sufficient products from the unit will be limited by the available pressure that has to overcome the buoyancy, and increased mine resistance thatconsumes any residual pressure. By documenting the limitations of this unit it will enable better decisions to combat a fire or spontaneous combustion event.

Oct 12, 2022