Search Documents

By J Plinke

The imperative to operate sustainably requires all equipment and processes to operate at their maximum possible efficiency. Achieving this ideal state requires a thorough understanding, not only of the process itself, but also of the tools available to design and assess potential improvements. This paper presents a case where the widely employed Discrete Element Method (DEM) toolset proved insufficient to model problematic material flow during the process of optimising wet screening performance. A Smoothed Particle Hydrodynamics (SPH) model was found to more accurately replicate the flow characteristics of the physical system. Site observations identified biased loading of the screen decks to cause inefficiencies in the wet screening of an iron ore processing circuit. Two numerical modelling approaches were pursued with the aim to select the most suitable one and continue the optimisation process based on that selected model. Selection criteria were established, based on the minimum requirements of being able to replicate the problem, including the main flow dynamics deemed to cause the issue. The DEM model was found to over-simplify the slurry flow dynamics within the scrubber and no laterally biased flow was introduced by the scrubber’s rotation to the otherwise symmetric system. Since DEM was not able to accurately replicate the existing problem, it was deemed an unsuitable method to assess the effect of any changes to the system. The second approach consisted of a SPH model. This model was deemed to map the flow within the scrubber with sufficient accuracy to address the problem, as it produced biased screen loading comparable to that reported from site. Changes to the wet chute, delivering material from the scrubber to the screen, aimed to neutralise the non-centrality introduced via the scrubber, were then successfully designed and assessed using the SPH model.

Nov 8, 2021

A belt of serpentinized ultrabasic rocks intrudes a moderately folded geosynclinal sequence of fine to coarse sediments, acid, intermediate, and basic volcanics as well as a batholithic mass of granitic rocks. The ultrabasic body contains small included masses of melanocratic and leucocratic rocks, together with chromium, copper, zinc, and nickel mineralization.

Jan 1, 1969

By Green A. D M

The establishment of the Imperial Smelting Furnace at Sulphide Coporation Pty. Limited for the smelting of zinc and lead made it necessary to design and install sintering capacity to produce approximately 500 t.p.d. of zinc-lead sinter. The updraught sintering process installed is a recent development and the plant was designed with adequate flexibility and equipment to enable operating staff to investigate the process and achieve maximum production under optimum operating conditions.Sulphur dioxide gases from the sinter machine are passed to a contact acid plant for the manufacture of sulphuric acid.

Jan 1, 1964

By Jiaxin Zhou

Acid mine drainage is a serious and chronic environmental problem of mining. This paper discusses the factors affecting the rate of acid generation by mine rocks and illustrates the relevance of these factors to the mines of the Northern Territory, Australia. The factors may be divided into two groups: internal factors and external factors. The first group covers characteristics of ores, mine waste rocks, tailings, etc and the second group covers surrounding conditions. The latter is further divided into four sub-groups, viz surrounding temperature and pressure, chemical conditions (ferrous/ferric adsorption ratio, total iron concentration, oxygen concentration and pH), surrounding biological conditions and mechanical conditions. Special attention is given to the surrounding P-T conditions, especially water partial pressure, and its relevance to the Northern Territory mines.

Jan 1, 1994

By S Mitra, D O’Dea, N Barrett, T Honeyands, E Copland

This work describes a novel mapping technique that allows the direct overlay of calculated local phase equilibria on micrographs of the physical system. The technique demonstrated integrates FactSage™, ver 8.2 (by Thermfact Ltd. and GTT-Technologies) phase equilibria calculations with mapped compositions determined by Scanning Electron Microscope – Energy Dispersive X-ray Spectroscopy (SEM-EDS) to visually express calculated properties while preserving the spatial information of the sample. The developed methodology is used to analyse interrupted blast furnace softening and melting tests containing mixed burdens of lump and sinter. Tests are interrupted at 1300C and cooled to room temperature for analysis. Phases present at room temperature are analysed to infer the liquid fraction and phases present at high temperature. Analysis of the interface regions between the dissimilar burdens allows insights to be gained into the interaction mechanism. During the transition from solid to liquid, migration and interaction of liquid oxide across the interfaces of the dissimilar burdens has been observed and demonstrated to impact softening and melting performance. Specifically, interaction of the oxides generated by lump (primarily FeO, SiO2 and Al2O3) and sinter (primarily FeO, CaO, SiO2, Al2O3 and MgO) are analysed, and the occurrence of a range of new mineral phases such as merwinite, melilite, olivine and bredigite observed.

Jun 19, 2024

Gekko Systems Pty Ltd have developed the Python Underground Processing Plant for the concentration of gold and sulfide ores. The Python plant has an established flow sheet including fine crushing, screening, gravity separation and flotation which aims to concentrate the valuable minerals (gold/sulfides). The aim of the plant is to achieve high valuable recovery into a mass yield of 10 - 30 per cent to reduce the amount of material that is needed to be taken to downstream processing. This paper examines the test work protocol for testing an ore to assess its suitability for the Python flow sheet. This paper will discuss the test methods employed to determine crushing requirements, continuous gravity recovery and flotation performance and how the results relate to Python design for the comminution, gravity and flotation circuits. Results from past test work will be discussed.

Aug 1, 2010

By E R. Ramanaidou, M Wells

The aim of this paper is to summarise all known Phanerozoic ooidal ironstone deposits worldwide, including Australian deposits such as the well-known channel iron deposits (CID). Nearly 400 occurrences have been catalogued based on stratigraphy, geographical coordinates, facies, grade, tonnage and iron bearing ore minerals. The description also includes details on the geochemistry, genetic models and main references. Brief statistical analysis provides an overview of the variation between these deposits. This compilation offers a basis for better understanding of the ooidal ironstone deposits and a global evaluation of this important resource worldwide.

Jan 1, 2009

By A Hatt

This paper presents a case study of characterisation work undertaken at a greenfield exploration project to provide engineering and OH&S inputs for the design of a ventilation system. The paper discusses how comprehensive early characterisation of the ambient surface and underground environment including aspects related to heat, dusts, strata gas, and geologic/mineralogical factors enables incorporation of the right ventilation and non-ventilation controls at a study level to mitigate the risks identified.

Oct 12, 2022

By M D. Griffith

Oct 12, 2022

By J Robertson, D Williams, H D. Plewes

The co-mixing of tailings and waste rock involves the intimate blending of tailings and waste rock to create a new material (Co-Mix) with superior physical and hydraulic properties. The new material has a low hydraulic conductivity, low compressibility, high water retaining capacity and high shear strength. Co-mixed tailings and waste rock restrict oxygen entry and water seepage to minimise acid generation and metal leaching. When compacted, Co-Mix materials have low volume change characteristics with respect to total stress and matric suction together with high shear strength. Co-mixed tailings and waste rock may be used to construct cover systems, internal barriers and seals, confinement structures or a full depth waste repository. The theoretical properties of Co-Mix blends are investigated. The results of a laboratory program to characterise the physical and hydraulic properties of co-mixed tailings and waste rock are presented. Various ratios of tailings were blended with different waste rock materials. Hydraulic conductivity tests were conducted at confining pressures ranging between 0 and 400 kPa. The saturated hydraulic conductivity for the Co-Mix materials was found to vary between 4 + 10-5 m/s and 5 + 10-9 m/s depending on blend ratio, waste rock type and confining pressure. These results together with other physical properties show excellent hydraulic and strength characteristics can be achieved for Co-Mix materials.

Jan 1, 2003

By A B. Richards

A brick veneer house located on a open-pit coal mine lease has been subject to ground vibration levels of up to 222 mm/s, and air vibration levels of up to 145 dBL. The dynamic response of the structure was measured with accelerometers, geophones, and strain gauges as part of a project investigating the response of brick veneer houses to blasting. This paper outlines the project, and provides information on brickwork strength, foundation investigations, and observations on damage due to blasting. Correlations have been made between crack behaviour and factors such as blast vibration levels and rainfall.

Jan 1, 2001

By J A. Cowburn

The high intensity zone within the Jameson Cell is the downcomer. It is largely external and separated from the flotation tank. This, together with operation of the downcomer under vacuum, rather than at elevated pressure and the absence of moving parts, allows ready access to the high intensity zone for measurement and analysis. Experimentation was conducted allowing measurements of recovery for residence times of between 20 milliseconds and ten seconds within the downcomer of a Jameson Cell. The affect of aeration rate on the recovery of different particle sizes was also studied.

Jan 1, 2005

By K Knorr

Desktop X-ray powder diffraction using a D2 PHASER equipped with fast linear detector was performed on several iron ore and mill scale samples. Data were analysed using cluster analysis and Rietveld quantitative phase analysis. The quantitative mineralogy of both materials could be established. Thus the input is provided for understanding the energy consumption and the CO2 emission during iron production. Furthermore, tabletop XRD allows to distinguish iron ore from mill scales and to quantify their mixtures.

Jul 11, 2011

By M Griffiths

This paper outlines an approach to high solids slurry pipeline design with data generated from a closed pipe-loop test system. The pressure and flow rate data generated is used to develop a pseudo-shear diagram for the purposes of system design. Following this approach enables the design of a full pipe flow system maximising system life and reliability. The alternative free fall system is explained and the disadvantages highlighted.Environmental and social considerations are discussed; mainly water and land use, and how designing for high solids slurry pipeline systems can be used improve these aspects of a mining project.Also discussed is how the use of high solids slurry pipeline systems can help to mitigate the risk associated with surface tailings storage facility failure, with the Bulyanhulu project used as a positive example.

Aug 8, 2011

By M Wortley, J McKay, D La Rosa, O Guyo

It has been a generally held concept that crushing operations were, by their nature, too simple to benefit from the implementation of advanced process control. The commissioning of an OCS¬ expert control system and image-based oversize detection system, VisioRock, at the Pilbara Iron Tom Price facility are dispelling these notions. A constraint-based OCS¬ expert control system has been designed and commissioned on the high-grade crushing and screening plant along with a vision-based oversize detection system functioning on six product conveyor belts. To date, the expert control has demonstrated the ability to increase production by maximising dynamic constraint utilisation. Dynamic constraint utilisation is a concept developed by Rio Tinto Technical Services for effectively evaluating constraint-based control logic performance. The VisioRock system has been installed and configured and has been operating for a period of several months. Currently, Tom Price and Metso personnel are working to define correct oversize detection thresholds. Details of the plant implementation are discussed.

Jan 1, 2006

By Robertson K. S, Hunter T. C

AEG-Elotherm's electromagnetic dosing channel, or Eldomet, is a recent invention enabling the transport and metering of molten metals. The development of a reliable refract- ory lining, and the use of suitable construct- ion and operating techniques has led to the successful application of the Eldomet for casting copper anodes at Copper Refineries Pty. Ltd.

Jan 1, 1974

By W Newton, J Price

This paper outlines the design, justification and performance of a gravity circuit upgrade at the Marvel Loch treatment plant. The design of the upgrade was simple but effective. The key components of the upgrade were the addition of a sluice and a second Knelson Concentrator. The sluice was installed as a pre-concentration step. The upgrade also included the purchase of a Mineral Cone to treat the increased quantity of gravity concentrate. The cost was low because of the use of mostly second-hand equipment. The result was that for a cost of $75 000 the gravity recovery doubled and the overall recovery increased by over one per cent. This paper shows that you do not need to spend millions of dollars to be innovative and successful.

Jan 1, 2000

By K Ehrig, V Liebezeit, Y Li, B Pewkliang, M Smith, E Macmillan

Pre-concentration of low grade ores via the rejection of low/no value materials based on fragment size is the subject of many published papers and studies over the past decade. However, the possibility of upgrading should not limited to low grade ores given the high cost of capital, energy, water, reagents, and ultimately tailings storage across the mining industry. Mining and processing facilities at Olympic Dam consist of an: 1) underground mine where ore is extracted via sublevel open stoping and 2) integrated processing plant located on the surface which produces Cu-cathode, Au-Ag bullion and uranium oxide concentrate. Blasted ore is trucked/trained to underground crushers which produce an ore feed with a product size P80 = -145 mm. Crushed ore is then hoisted to the surface and delivered to the ROM pads via an overland conveyor. The typical copper grade of mill feed is approximately 2 wt%. A rapid assessment of the potential to upgrade Olympic Dam mill feed prior to the ROM pads via rejection of low value materials based on fragment size was completed using existing data. Three separate datasets were utilised to assess the deportment of Cu, U, Au across size ranges of 200 mm down to sub-8 m. Cumulative grade vs cumulative mass distribution graphs for each element were produced. This data clearly demonstrates that Cu, U, Au grades remain constant down to ~212 m, which happens to be the liberation size of the sulfides. Hence, no potential to upgrade the ore stream via rejection of +200 mm - to ~212 m sized materials prior to milling. Mineralisation within the Olympic Dam Fe-oxide Cu-U-Au-Ag deposit (IOCG) occurs as disseminated sulfide grains within granite- to hematite-rich breccias. The typical sulfide grain size is sub-200 m that supports the outcomes of the grade deportment by fragment size study.

Nov 10, 2020

By A Sinuhaji, R Poedjono, G Flumerfelt

PT Freeport Indonesia is currently building the DOZ mine. It is a 25 000 tonne/day block caving operation which is scheduled to reach designed production levels by the fourth quarter of 2002. This paper describes some of the issues and challenges faced by the operation when introducing a new undercut method part way through the project. Advantages and disadvantages are discussed as well as the expected benefits of the new method.

Jan 1, 2002

By Revy T

A testwork program aimed to improve the assaying of underground face samples established that for an Accelerated Cyanidation Extraction using the LeachWELLTM 60X catalyst, followed by an Aqua Regia finish (to quantify non-cyanide-extractable gold): ò Assay results (including the aqua regia finish) from a full set of samples from one underground face can be returned within four hours. ò The reagent dose to make the method simple and 'bullet-proof' is 8 gm LeachWELLTM 60X and 20 gm NaCN per 200 gm sample (30 per cent solids). Pulverising is to 90 per cent passing 75 micron (compared to the standard of 90 per cent passing 150 micron), and cyanidation is completed within one hour - however both might be further optimised. ò The LeachWELLTM/Aqua Regia results demonstrate that Fire Assays suffer from a significant nugget effect which makes the Fire Assay data relatively unreliable. ò Original costs, specific to Bannockburn (viz including an Aqua Regia finish), handling approximately 20 000 to 25 000 per annum is estimated to be $5.40, ie about one-third less than fire assaying. Optimising is further reducing these costs. It is estimated that the LeachWELLT"'/Aqua Regia assay procedure has reduced the probable error limits of any given assay of this ore from the range 0.74x to 1.36x for Fire Assay, to an appreciably smaller range of 0.90x to 1.11x. Thus for a cut-off grade of 1.60 g Au/t, samples with Fire Assays ranging up to 2.18 g Au/t have 25 per cent chance of being below cut-off, while samples with Fire Assays as low as 1.18 g Au/t have an equal chance of actually exceeding cut-off grade. This 1 g Au/t range in uncertainty is generally unacceptable for many practicalgrade/tonnage relationships. By contrast, using LeachWELLTM + Aqua Regia assays, the estimated corresponding limits are 1.44 g Au/t and 1.78 g Auk respectively - a far more tolerable 0.34 g Au/t range of uncertainty. Subsequent data has demonstrated that sufficient accuracy for grade control is achieved by Accelerated Cyanidation alone, further halving the cost of assays.

Jan 1, 1994