Search Documents

By D J. Williams, C Zhang, F E. Herrera Cabrera

Farming on bauxite residue using screw propelled equipment (SPE) has been commonly practised to accelerate dewatering and as it promotes consolidation and enhances storage capacity. However, it is unclear when and how often farming should be conducted during the transition of bauxite residue from slurry to dry solids and how deep each slurry deposition should be. To address this issue, three desiccation tanks were established in the laboratory to investigate how much farming could enhance the desiccation and consolidation of tailings. The cuboid tanks, of 350 mm in height and 300 mm in width and length and with an opening on the top, were placed on load cells to monitor the water loss during desiccation and were instrumented with moisture and suction sensors designed and developed at the University of Queensland to measure the water content profile of the residue. The bauxite residue, composed of silt-size particles with low plasticity, was hydraulically deposited in the tanks as a slurry at 27% solid content, resulting in 100 mm depth of solid material settling. Evaporation was enhanced by placing two identical electrical fans above the tanks. Two phases were conducted. In the first phase, the two tanks were left untouched for evaluating non farmed conditions and for calibrating sensors, while in the second phase, three tanks were subjected to atemporal farming using purpose-built screw propelled equipment. The experiment was terminated when the residue was completely desiccated. This paper reports on the instrumented tank set-up and the results obtained to date.

Jul 1, 2021

By P Hanna

In an effort to improve returns to shareholders, the Australian Mining Industry has consolidated considerably over the past decade or so. Technical services at mines have been re-structured, whilst those at corporate offices have been all but eliminated. A recent study of the role of the geologist in BM Alliance Coal Operations Pty Ltd (BMA), showed the adverse impact on the companyÆs performance due to a lack of geologists. With an education campaign, to demonstrate the contribution of geologists to the æbottom lineÆ and in increasing the options available to the company, the value of the geology role became better understood. The implications of the loss of invaluable corporate knowledge, when long serving geologists left the company, also became clear. Steps have since been taken to increase the numbers of company geologists, particularly on mine sites. In common with other sectors of the mining industry, the Australian coal industry is experiencing a critical shortage of experienced coal geologists, as companies have found in recent recruitment efforts. This is further evidence that the recommendations from the recent study by World Competitive Practices, commissioned by The Australasian Institute of Mining and Metallurgy, æRising to the ChallengeÆ have not been adopted. People, and the mineral resource base, are the assets from which mining companies gain a sustainable competitive advantage. Geologists, as the nexus between the resource base and people, are in a unique position to enhance the profitability of their companies. To maximise their contribution to the industry, and ensure that they receive due recognition, geologists must adopt a more commercial approach in their work and take a front foot stance in promoting their value to management. Geology is a core competency for all mining companies. The tendency for companies to outsource this function, to the detriment of the company geologist role, is not sustainable in the longer term. TodayÆs geologists need to work closely with management, technical and human resource professionals, universities and schools to ensure their significant value is well understood, and that the industry can attract, train and retain new recruits through the implementation of graduate programs and company career paths.

Jan 1, 2003

By S B. Fitch, S A. Wilson, A J. R Barr, P R. Searle

Improving the safety culture and performance of any operation is a fundamental goal of every mine operator. Methods of implementing, or changing a culture have developed from the early methods of operant conditioning, for example rewarding crews for achieving nominated safety milestones i.e. 3 months Lost Time Injury (LTI) free through to the current model of engaging a workforce through education and empowerment. As a large scale and mature operation with multiple contractors, Telfer has been exposed to numerous programs throughout its history. This has provided the opportunity to build on and complement these systems by integrating key elements from each. SAFE 360° is a new approach developed to engage the workforce in a holistic approach to encourage positive behaviours across all facets of an individual’s life which results in a focus on situational awareness at all times, rather than being workplace specific. It is based on three key modules: • Emotional Intelligence • Mindfulness • Situational Awareness Each module has a series of modules that help enhance the individual’s sense of self, leading to an ability to self-reflect and self-manage whilst empowering them with the moral courage to challenge their peers to raise standards. Since commencing this SAFE 360° behavioural safety risk management journey in November 2017, we have witnessed a change in the way our workforce engages with each other, their workplace and with management. There has been an increase in hazard perception, identification and ownership of issues, and we have seen a significant decrease in site TRIFR rate from 13.7 to 5.7 (as of April 2019). This paper will provide an overview of the program, how it has been implemented, case studies to demonstrate outcomes and KPIs used to measure effectiveness.

Mar 15, 2021

In March 2003, Rio Tinto Coal AustraliaÆs (RTCA) new Hail Creek open cut coal mine commenced operations in the Bowen Basin. Hail Creek is a two-seam strip mining operation utilising two 90 m3 draglines and a fleet of excavators and trucks to remove the overburden. All overburden at Hail Creek is blasted prior to excavation. The mine conducts its own drill and blast operations while engaging Dyno Nobel for the provision of explosives supply and loading truck (bulk explosives vehicle û BEV) services. This arrangement was favoured over outsourcing the entire blasting function to a contractor. Subsequent to a value engineering review, the mine set about developing and implementing a blasting operation that did not rely on the need to store bulk quantities of ammonium nitrate on site. There were advantages identified in doing this, in particular the reduction of capital expenditure required and reduced exposure to a number of recently introduced security requirements. This approach also makes sense operationally. The establishment of reload facilities for the BEV close to the blasting location, where turnaround times are kept to a minimum, increases the productivity of the BEV. For this strategy to be successful the logistics of ammonium nitrate supply into the blasting operations has to be well planned and thoroughly executed. This means a robust planning and forecasting arrangement needs to be established with the supplier and transporters of the ammonium nitrate. To date, 80 million bcm of overburden has been blasted at Hail Creek and each year the quantity of overburden requiring blasting is increasing. The purpose of this paper is to present the findings of a study: evaluating the effectiveness to date of the strategy to conduct blasting operations without ammonium nitrate storage on site, and identifying whether there is a limit to which this strategy can operate after which the introduction of bulk ammonium nitrate storage facilities are necessary.

Jan 1, 2007

By M F. L Gibson

The issue of flyrock is very important in the operation of all mineral extraction sites that use blasting. Unlike the other environmental effects of blasting, ground vibrations and air overpressure, flyrock is (or should be) a rare event, with severe consequences which may include damage to property, injury or fatalities. These physical consequences are often matched by a loss in public confidence in the management of the operation, mistrust and bad press. In this work a deterministic analysis of flyrock was carried out using the equations of a particle in motion with drag. The solutions to these equations were used to reproduce the curves of Lundborg et al (1975) for the relationship between flyrock boulder size and maximum ejection distance. A probabilistic approach based on Monte Carlo simulation was built up with the analytical model using published data together with local case study material. A typical quarry blast situation was modelled and estimates of safe standoff distances were determined using risk assessment techniques.

Jan 1, 2001

By A Teen

An open cast mine on the West Coast of the South Island of New Zealand proposes to remove up to 30 m of overburden to access an ore body neighbouring National Reserve land. Part of the conditions of the mining permit is that no material above natural discharge levels may be released over the Mining Lease boundary onto the adjacent land. In order to meet this requirement, the client has contracted the design and installation of over 2.6 km of high energy dynamic rockfall control barriers. This paper describes how the rockfall hazards were assessed and the rockfall barriers dimensioned. The design involved 2D modelling of over 3000 simulations.   Modelling parameters were calibrated during field trials at a purpose built section of barrier. The resultant energies ranged from 500 to 3000 kJ. The construction phase of the project involved the drilling, anchoring, and installation of certified barriers up to 7 m high in a remote and inhospitable climate with limited machinery access. By exploring best practice in this specialized field of engineering, a novel rockfall hazard mitigation solution was identified.

Jan 1, 2007

By J Pearce, B Miles, V de San Miguel

Incorporating industry best practice waste rock management methods can be a relatively straight forward task when preparing management documentation, such as an acid and metalliferous drainage management plan (AMDMP). However, a key difficulty is the incorporation of industry best practice methods that are practical and non-compromising on their purpose from a scientific standpoint. The second key difficulty is the implementation of these practical methods as various operational groups/departments are typically relied upon to execute and take ownership of different tasks or procedures.One approach to overcoming these difficulties is to develop an AMD Operations Manual (AMDOM) that:•Incorporates, where practicable and without compromising scientific merit, existing processes that those groups/departments ultimately responsible for the execution of the management action are familiar with; and•Provides standalone, simplistic, and easy to follow procedures for site personnel. The purpose of the standalone operations manual is to ensure site personnel who are responsible for undertaking specific procedures, have clear, step-by-step instructions for an individual procedure, without requiring interpretation and understanding of the more comprehensive AMDMP.In adopting a best practice approach to waste rock management for their iron ore mine in Western Australia’s Pilbara region, Roy Hill developed an AMD Management System that is comprised of both an AMDMP and an AMDOM that are connected through adaptive management processes. The Roy Hill iron ore mine, which has a mine life of 18 years, will require the management of more than three billion tonnes of waste rock.CITATION:de San Miguel, V, Miles, B and Pearce, J, 2018. Practical waste rock management at the Roy Hill iron ore mine, Western Australia, in Proceedings Life-of-Mine 2018, pp 80–82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By M Brewster

Goldfields Abosso Goldfields Limited (AGL) is a Ghanaian registered company that owns and operates the Damang Gold Mine. Gold Fields Ghana Holdings Limited holds a 71.1 per cent interest in AGL. The Damang concession held by Gold Fields Ghana Holdings Limited covers a total area of 271 km2 located 40 km north of the town of Tarkwa in the south-western part of Ghana. Gold Fields as a company registered on the New York Stock Exchange is legally obliged to be SOX (Sarbanes-Oxley). Sarbanes-Oxley Section 404 (SOX404) is on management assessment of internal controls. The Mineral Resource Management (MRM) function of AGL manages three Prospecting Licenses and two mining licences. At least ten pits/prospects are scattered along the two limbs of the Damang Anticline and have two main types of mineralisation notably Paleoplacer and Hydrothermal. Thus SOX404 procedures are put in place to treat each mineralisation type in the best way for reliable resource outputs and estimates. Generating auditable resources for AGL is a prime but most important function of MRM. Thus important checks are built and designed to ensure that all relevant geological and geostatistical inputs conform to procedures outlined under SOX404 requirements. More importantly sign offs are designed to ensure that technical personnel involved in all aspects of resource and reserve generation are satisfied and can be held accountable.

Jan 1, 2007

The face of project evaluation is changing continuously, making it ever more critical to get a clear understanding upfront of the objectives, decision-making processes and criteria of the project proponents. Requirements are usually significantly different for emerging æjuniorsÆ compared with long established major mining houses and companies in developing countries compared with western companies. Requirements are also different for different types of evaluations, such as due diligence studies compared with feasibility studies of æownedÆ projects and there are often key misunderstandings around the use of the term æbankableÆ. Further, it has become increasingly important with increasingly remote and lower quality resources to understand risk relativities such as infrastructure compared with the core processing facilities. This has also driven the need for more trade-off studies to determine the best balance between critical issues, such as optimisation of the interface between mine and processing plant, capital versus operating cost and automation versus labour. In every project evaluation, it is also critical to consider emerging trends and changing requirements and standards such as sustainability and community interface. Finally, the inescapable drive to reduce time to market has driven changes such as increased use of more standardised designs and innovative approaches to the transition from project development to execution. This paper begins with a brief review of the different objectives and risks of each project development stage to establish a framework for subsequent discussion of the different requirements of different types of companies in different locations, different types of evaluations and different types of projects and project components. This is followed by a review of changing requirements and standards and some innovative developments in sustainability and community interface are presented. Finally, the paper outlines a number of developments in the area of operational readiness planning that focus on minimising the time to achieve maximum return on investment.

Jan 1, 2009

By R Bezuidenhout, J K. Claflin, S R. La Brooy, G M. Wardell-Johnson, A M. Claflin

Best practice gold (Au) recovery is not an accident. It is the result of proper operation of the adsorption circuit using good quality activated carbon. A conventional carbon ‘regeneration’ kiln cannot process carbon fouled with floatation chemicals and achieve best practice gold recovery. A high temperature, controlled atmosphere carbon ‘reactivation’ kiln is required. Carbon circuit design allows for low quality carbon by increasing the carbon advance rate, carbon inventory and setting an easily achieved and commercially prudent solution tails target of typically 0.02 ppm Au. These design criteria are important to ensure the commercial success of the gold operation in the first instance. Most carbon ‘regeneration’ kilns will produce carbon of sufficient quality to achieve a 0.02 ppm Au solution tail in the absence of flotation reagents.Best practice recovery is considered less than 0.005 ppm Au in solution reporting to tails. If the carbon is heavily fouled, as it will be if used for flotation leach circuits, then a conventional carbon ‘regeneration’ kiln cannot achieve world’s best practice recovery no matter how much carbon is advanced. World’s best practice gold recovery requires a carbon ‘reactivation’ kiln and the whole of the carbon circuit operated optimally.The competing reactions occurring in a carbon ‘reactivation’ kiln are presented and discussed in terms of kiln design and operation. New industrial and laboratory findings are presented to fill gaps in the body of knowledge and identify that a large reduction in residence time at temperature will not significantly impair reactivation, but can significantly reduce the size and cost of the kiln or permit significantly increased carbon throughput.The carbon circuit performance is modelled in terms of gold adsorption, as a function of carbon reactivation using ‘simulation of carbon-in-leach/carbon-in-pulp circuits’ (SIMCIL). An optimum carbon advance rate is identified as a function of optimum carbon ‘reactivation’ kiln operation to achieve 0.005 ppm Au in the tails solution. A conventional carbon ‘regeneration’ kiln is compared to a state-of-the-art carbon ‘reactivation’ kiln in terms of reactivation performance and gold recovery.CITATION:Claflin, J K, La Brooy, S R, Wardell-Johnson, G M, Bezuidenhout, R and Claflin, A M, 2017. Optimising carbon reactivation kiln operation, in Proceedings MetPlant 2017, pp 346–364 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By D Readett

The most critical variable in the successful establishment of the Murrin Murrin Heap Leach plant was the effective agglomeration of the Ni laterite ore. This paper describes the test work undertaken to establish the key agglomeration parameters including state of the art testing and analysis procedures. These parameters were then utilised to establish the key design and operational concepts for the world’s first commercial scale Ni laterite heap leach. Following the technical and economic success of the operation, the actual operational data is compared back to the original test work data.

Aug 8, 2011

By F Ouchterlony

Soviet precursors to Cunningham’s Kuz-Ram model from 1983 are described. They are rooted in the mean fragment size and Rosin-Rammler (RR) fits to sieving data and rely on approximations. Three versions of the Kuz-Ram model are presented and all three are de facto based on the median fragment size x50, even if the term mean is used in the papers. This discrepancy caused Spathis in 2004 to suggest a correction procedure for the Kuz-Ram rock factor A, which was said to explain some of the missing fines in the model. This correction, while applicable to Cunningham’s 1983 paper, does not apply to his 1987 paper, in which he presents his own A factor.Common fixes of the Kuz-Ram model’s fines issue are fragmentation models where the fines are mainly generated in a crushed zone around a blasthole. This is contradicted by careful model blasting tests. The lack of a largest block size in the RR function may lead to spurious values of the uniformity coefficient n, eg in conjunction with image-based fragmentation measurements or crusher modelling. These issues may be solved by using the transformed RR function, which has a largest block size xmax or its replacement by the Swebrec function, such as in the KCO model.The mean to median issue is investigated in some detail and it is found that using x50 instead of the mean:has a sounder theoretical backgroundis less prone to errorsis not contradicted by the original Soviet data.It is finally suggested that future work on fragmentation prediction equations focus on the use of distribution independent quantities like percentiles, eg x50, x20 and x80. Some previous work in this direction is briefly analysed and one consequence is that the n-value of the Kuz-Ram model should depend on specific charge.CITATION:Ouchterlony, F, 2015. The median versus the mean fragment size and other issues with the Kuz-Ram model, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 109–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By T N. Little

This paper is concerned with the influence of engineering geology on design of Wall Control Blasts. In the Introduction, the Blast Management Framework and the Blast Design Requirements classification system (previously developed by the author) is drawn upon to set the context. Blasting objective for all wall control blasts involves both profile and damage control. Four classes of approaches for blast design are outlined and briefly discussed. Five distinct wall control blasting techniques are summarised. The general relationship between geology and blast design is explored in the paper. Influence of geology on pre-split and post-split design and blasting direction is highlighted. Wall damage modelling from the closest row of blastholes is also introduced using the Analytical Damage Model (ADM). The relationship of rock properties and explosive selection and in particular the Mach wave generation is introduced to assist blast designer in this regard. Finally a Conceptual Model that relates vibration, damage and rock mass condition has been presented along with some applications that have been undertaken by the developer. Eight conclusions have been formulated based on extensive work in this area and the current study.

Jun 22, 2022

By J Mauk, J Rowland

The Karangahake epithermal Au-Ag mine consists of two main lodes, the Maria and the Welcome/Crown hosted in Miocene andesites. Mineralisation is strongly constrained to major structures and is genetically linked to dynamic tectonic processes. Two main periods of faulting are represented in the deposit: 1. NE striking right-lateral/normal oblique linked spatially and temporally with the mineralising system, and 2. ESE striking right-lateral/normal oblique post-mineral faulting that displaces the lodes. Paleostress analyses performed on a limited kinematic data set indicate NW-SE extension during the formation of the vein system. Veins and lodes strike NNNE and accordingly contain a strike-slip component. The kinematics of vein formation at Karangahake is broadly consistent with that of other deposits within a NNE-trending belt of deposits. Oblique shear on deflecting structures will create zones of compression and dilation. Dilatant zones created on steep structures create fluid pathways potentially focussing large volumes of fluid from deep parts of the system into dynamic structures.

Jan 1, 2003

By G M. Volkmann

Pipe umbrella support systems – also called canopy tube systems – have been used successfully for tunnelling in challenging ground conditions since the 1970s. Historically, the drilling unit was the limiting factor for pipe umbrella installations – less attention has been paid to pipe couplings and their influence on labour time and load-bearing capacity.This contribution investigates the influence of the type of pipe connection on the load bearing characteristics of a connected pipe and discusses associated influences on design calculations and installation performance. Standard thread connections reduce the effective cross-section and thereby load-bearing capacity in the connection area. To achieve design parameters, over-dimensioning of the un-weakened pipe section is the only way to overcome this limitation. Recently, two new, alternative connection types were designed and developed for connected pipe umbrella pipes. The first one is the nipple coupling, consisting of fitting with a threaded connection that is pressed and welded into the ends of standard tubes. The second type is the squeezed connection, which mechanically connects non-threaded pipe ends, achieved by force-fitted squeezing from the drill rig. Both coupling types have technical as well as operational advantages compared to the common thread couplings, which are the weakest point in the support system.In the following sections significant technical differences are explained, design values given and a site example presented to illustrate the operational advantages of the newly developed coupling?type.CITATION:Volkmann, G M, 2014. Development of state-of-the-art connection types for pipe umbrella support systems, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 333–338 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By W Assibey-Bonsu

The paper provides a brief review of the multivariate uniform conditioning and the localised multivariate uniform conditioning techniques and presents a case study based on a porphyry copper gold deposit in Peru. Two other important scenarios have been investigated and will be particularly emphasised: The recovered selective mining unit (SMU)s depend on a combination of copper and gold content, which can be expressed by means of ænet smelter returnsÆ (NSR). Two approaches are compared. Firstly, the application of a composite cut-off on NSR on the joint distribution of each grade and the application of uniform conditioning to three variables is investigated, ie for the first approach NSR is used as the main variable. The second approach considers copper as the main variable. In the case of multiple domains the procedure used to apply the technique to process mixed panels is clarified and recommendations are made.

Sep 26, 2011

By V Yadi

Geostatistics has been widely used for more than four decades as a powerful tool in ore resource/reserve estimates and grade control. This method has gradually replaced the conventional method such as polygon and cross-section for grade estimation by more mathematical techniques such as kriging. The advances in geostatistical understanding and the availability of appropriate software packages have given much more contribution in speed and high accuracy during production. However, in many cases, these techniques are sometime applied without support with a good thorough understanding of the geological controls on metal distribution. To produce the result close to actual, the geological control in interpretation and appropriate geostatistical task is a must. Geological logging was described in the core must be consistent with the level plan produced by commercial modelling software used as a guide for grade control during production. Experience gained through evaluation of the Central I deposit resulted that the most effective systems continue to be based on geostatistical methods of resource estimation. Computer applications modelling software packages are necessarily as the core of an efficient in undertaking these assignments. They contribute to make a valued to data management and are becoming increasingly effective during processing. The latter role is particularly important to check the actual versus estimated values where will significantly to improve personnel to have a confident with their knowledge combined with experience and complete their jobs satisfy.

Aug 22, 2011

By T Sua, B Wright

"BHP Billiton West Australian Iron Ore (WAIO) conducts an extensive geometallurgy program for its iron ore deposits in the Pilbara with the focus on determining the lump yield (the mass percentage of >6.3 mm rocks) and the lump and fines grade for iron ore products. The geometallurgy program provides accurate information to design engineers and technical marketing teams on the performance of different iron ore mineralogies for future deposits. Additionally geometallurgy results are being used to guide short-term production planning with their introduction into short-term geology models and grade control models. The data that underpins this knowledge is from dedicated geometallurgical programs, drilled using PQ (~83 mm) holes. These holes are crushed by intervals that are based on geological definition which provides an indicative lump yield and lump and fines grade. The lump is then subjected to standard dropping and tumbling test stages to produce a simulated lump and fines product. In the past, quality assurance, quality control holes were drilled using HQ (~64 mm) holes for geochemistry purposes. These holes were crushed to provide an indicative lump yield and lump and fines grade and then 100 per cent is sent for assay (with no dropping and tumbling). Utilising data from HQ holes can significantly increase the indicative geometallurgical data available. This paper compares the geometallurgical results from both PQ and HQ holes from a range of bedded iron deposits (Brockman and Marra Mamba). The PQ and HQ data are compared by orebody, stratigraphy and depth to exclude factors that are expected to influence geometallurgical results.CITATION:Wright, B, Sua, T, Robertson, B and Van Dijken, B, 2016. Comparison of Diamond Drill Size on Iron Ore Geometallurgical Results, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 161–166 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By M Nagarajan, S Esen

This paper presents three case studies from three surface coalmines. The first case study is from a coalmine where a dragline operates in 60 m wide and 1 km long strips. Typical overburden height ranges from 30 m to 50 m. The base case blast was modelled using an advanced blasting model (Distinct Motion Code – DMC) to establish the baseline using the blasting parameters in use before optimisation. DMC was used to model the alternative blasting scenarios to obtain the following key objectives:the post-blast muck pile profile was required to have an optimum height of ~28 moptimise cast percentageachieve a well-fragmented muck pile for the draglinethe muck pile profile should be appropriate for the dragline entry into the strip.Achieving these objectives would optimise the dragline performance through reducing rehandle and improving advance along the strip. DMC modelling resulted in the following outcomes:the required muck pile profile could be achievedthe cast percentage increased from 21.1 to 25.1 – a four per cent increaserehandle volumes were reduced.Establishing a good quality assurance / quality control (QA/QC) process was essential to delivering a blast that could achieve these outcomes. The blast was fired successfully and the dragline completed the strip approximately two weeks ahead of the time taken for the previous strip.The second case study is from a coalmine where D11 dozers are used to move the blasted material to the spoil. An optimum profile was required for the dozers for this low-cost mining operation. To achieve this, an electronic blasting system (uni tronicTM 600) was introduced to optimise the muck pile profiles being delivered. The new muck pile profiles showed improved cast percentage from 10.6 per cent to 17.8 per cent. The changes in the muck pile centre of mass displacement improved dozer efficiency as a result of pushing material shorter distances to its final position. Dozer productivity (bcm/h) statistically did not change but coal was being exposed at a faster rate.The third case study summarises the results from a site where dozers are used to minimise the total mining cost. Traditionally, excavators had been used on-site with conventional blast designs. After firing the first cast shot, the blasted material was found reasonably well-fragmented. Although dozing productivity hasn’t been quantified on-site, operators were providing positive feedback (easier push) due to the reasonably good muck pile profile suiting to the dozers. This site also realised significant savings with the dozing as compared to their truck/shovel operation.CITATION:Esen, S and Nagarajan, M, 2015. Muck pile shaping for draglines and dozers at surface coalmines, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 409–416 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By B D. Burford

High intensity stirred milling using the IsaMill has been the enabling technology for many projects by transforming the economics of fine grinding and simplifying circuit design. IsaMill grinding technology was originally developed for large-scale grinding to P80 sizings of 7 ¦m. The IsaMill is a high throughput, high efficiency mill that produces sharp product size distributions in open circuit configuration. The ability to grind in an inert environment, using a wide variety of media types, can give further metallurgical and economic benefits. The high energy intensity results in a small footprint that enhances the ability to distribute grinding power throughout the circuit, applying grinding energy to the minerals that need it. Recent scale up developments in IsaMill technology have enabled the benefits to be extended to large-scale conventional grind sizes, until now the domain of ball and tower mills. This paper will examine the crossover of IsaMill technology from ultrafine applications into the more conventional grinding area (P80 20 - 150 ¦m). Scale-up developments in IsaMill technology that have enabled this are reviewed. The upcoming commissioning of a 3.0 MW M10,000 IsaMill, the most powerful to date, grinding to P80 55 ¦m at PPL in South Africa will be discussed, as will the recent commissioning of a 2.6 MW M10,000 IsaMill at Kumtor. Recent testwork at McArthur River, where an IsaMill is being considered as an addition to the primary grinding circuit to replace the current tower mill will be reviewed. The potential combination of HPGR and IsaMill to transform concentrator grinding economics will also be discussed. Large-scale IsaMill technology has the ability to transform circuit design and energy efficiency for both coarse and fine grinding.

Jan 1, 2006