Search Documents

By G Small, A Lazamanana, C Greet

When conducting gold leach tests on free milling gold ores which method is the best, bottle rolls or the stirred beaker test? Recently, a client requested that gold leach tests be conducted using the stirred beaker methodology. When asked why, because the laboratory was set up to conduct tests using the bottle rolls technique the reply was that the stirred beaker leach test would replicate the plant more closely. Not wishing to upset the client, the instructions were followed. However, the opportunity was taken to complete additional tests so that the two leach procedures could be compared. Further, this comparison was completed on two different gold ores as well as a number of different grinding media types.This paper provides a description of the two laboratory techniques employed, and presents the results of these parallel tests. Interestingly, the assertion that the stirred beaker methodology more closely replicated plant performance was not validated. In fact, the results obtained using this procedure were noticeably different from those observed in the plant, with lower recoveries and significantly higher cyanide consumptions. The bottle rolls test however more adequately replicated plant performance in terms of recovery and cyanide consumption. The reasons for this are discussed in the paper.CITATION:Greet, C, Lazamanana, A and Small, G, 2015. Bottle rolls versus stirred beaker leach testing – which is best?, in Proceedings MetPlant 2015, pp 188–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By G Pizarro, O Miranda, D Rosales

In panel/block caving mines, large amounts of information are collected at the operations. This information includes grades and extracted tonnage, fragmentation, lithology, design of stopes and main infrastructure, geotechnical information, overbreak progress, seismicity, numerical modelling and many other mine variables. To improve the reliability of the production plan it is required to integrate the mine data into one platform. In this paper, the logic of a new technological platform is presented for analysis, modelling and design in panel/block caving mines. The platform includes an acquisition system for mine data and geotechnical information, a back-analysis module for calibrating statistical models and a module of visualisation of the results. The application and benefits of the platform is illustrated for mining induced seismic risk for panel/block caving mining operation. The platform can be used in the mine design and planning processes and is useful for reducing uncertainty in the mining business of panel/block caving operations.CITATION:Miranda, O, Rosales, D, Pizarro, G and Vallejos, J, 2016. Development of an integrated platform for the analysis, modelling and design in panel caving mines, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 237–240 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Planning for the Macraes Extension project highlighted the need for additional tailings storage availability. The possible solution of developing new tailings impoundments in Northern Gully, in tum, led to concerns being expressed by the regUlatory authority over the assimilative capacity of Deepdell Creek. Philosophical differences over the appropriateness of applying a seepage model used to set standards in consents for the original project resulted in the company re-evaluating the whole monitoring system associated with tailings disposal and seepage control. Re-evaluation indicated problems arising from the existing in-stream water quality monitoring in respect of protection of the aquatic ecological system and verifiability of results. A new monitoring system was designed relocating the compliance monitoring point out of the stream and into the gully containing the tailings impoundments giving greater certainty of monitoring results to all parties and providing improved protection for the aquatic ecology of Deepdell Creek.

Jan 1, 1993

By D La Rosa, K Caron, H Mamani, W Valery, R Diaz

The Gold Fields Cerro Corona copper-gold deposit in Peru has heterogeneous rock characteristics in terms of its mineralogical, geological and geotechnical properties. Blast design variations in these conditions directly impact the run-of-mine (ROM) fragmentation, which in turn influences downstream process efficiencies. In particular, when harder ore is processed, throughput and circuit performance may be limited.To evaluate the potential to increase throughput and improve overall plant performance by optimising blasting practices and comminution circuit operation, Gold Fields La Cima engaged Metso Process Technology and Innovation (PTI) to conduct a full process integration and optimisation project at Cerro Corona. Blasting, crushing and grinding processes were reviewed to identify the potential to achieve substantial improvements in productivity when treating the most competent ore types.Site-specific models of the blasting, crushing and milling processes were developed using SmartTagTM ore tracking technology for calibration and validation. Ore tracking permitted locations in the blast volume to be queried against the geotechnical block model to determine the hardness and structural parameters of the feed to the comminution circuit. They also ensured surveys were conducted when ore from the audit blast was flowing through the crushing and grinding circuits.The predictive models developed enabled PTI to demonstrate how changes in blast design influenced both ROM fragmentation and the performance of downstream comminution processes. Outcomes of the project suggested changes to blast designs and comminution practices, and these were partially implemented for a validation trial. The trial demonstrated a 14.8 per cent increase in mill throughput for the specific ore selected for the study, and an average increase of 5.7 per cent for all ore types. There is potential to further increase throughput and process performance if all recommendations are implemented. This paper describes the methodology used and benefits to the operation from the mine to plant.CITATION:La Rosa, D, Caron, K, Valery, W, Diaz, R and Mamani, H, 2015. Blast fragmentation impacts on downstream processing at Goldfields Cerro Corona, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 333–342 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Kubik K

Recent significant advances in the Global Positioning System (GPS) have contributed to making real-time kinematic/dynamic process for decimetre to centimetre-level positioning more reliable and ready for the production-use. As a result of research and development efforts in this area, a robust real-time kinematic (RTK) GPS positioning prototype system has been established at QUT for both scientific and engineering purposes. This system is finding applications in a wide range of automobile robots or automatic guidance vehicle systems. This paper first summarises the theoretical basis necessary for centimetre real-time kinematic positioning, then gives a brief description for the real-time dynamic GPS system developed at QUT. The paper summarises the results of a designed vehicle tracking test. The results demonstrated that the differences between RTK filtering solutions and OTF solutions are in the order of magnitude of about 20 centimetres and the accuracy of OTF solutions are in the levels of two centimetres. This confirms that the RTK system delivers three-dimensional position with decimetre-to-centimetre accuracy. This particular RTK processing system is robust and reliable, although the system is referred to as a prototype and will be further developed.

Jan 1, 1997

By C A. Foss, K Leslie, C Arnold

Magnetic susceptibility measurements provide rapid, non-destructive testing of drill core, but cannot directly map magnetite and/or hematite content. Combined magnetic susceptibility and magnetisation measurements provide much more diagnostic information and, with sparse calibration constraints, are able to quantify magnetite and hematite concentrations and potentially map differences in grain size and texture. We have developed a travelling three-component vector magnetometer that can be run alongside core to map its external magnetic field. The logger has been designed to operate in core sheds and at remote drill sites. It is used to rapidly scan a length of core, with each core being scanned in different rotations. The magnetic field contributions from any remanent magnetisation rotates with the core and cause differences between successive measurements, while the field contributions from any induced magnetisations with isotropic magnetic susceptibility remain constant. Deconvolution of the magnetic field data with simultaneous three-channel inversions of the multirotation data separates remanent and induced components. Interpretation of this data provides estimates of the intensities of induced and remanent magnetisations, the orientation of the remanent magnetisations and the ratios of the induced and remanent magnetisation strengths. We expect these magnetisation parameters to correlate with stratigraphy through a banded-iron formation. Furthermore, we anticipate that we will be able to use this information to map zones of oxidation and other changes along the core. This novel instrument is one component of an integrated CSIRO program to provide new capabilities for iron ore exploration and development based on studies of magnetic fields and magnetisations at scales ranging from centimetres for these core investigations to tens of kilometres for formation studies.CITATION:Foss, C A, Leslie, K and Arnold, C, 2015. Rapid logging of different magnetic phases in banded ironstones using a travelling three-component vector magnetometer, in Proceedings Iron Ore 2015, pp 271–276 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By N Cusworth

The development of a resource project inevitably requires the investigation of a vast range of issues across most engineering disciplines û mining, metallurgical, chemical, civil, electrical, mechanical and environmental û as well as the geosciences. It is also a characteristic feature of the resource industry that no two orebodies û and hence no two development projects û are the same. So these technical issues have to be addressed to a greater or lesser extent in evaluating any resource projectÆs development potential. Not surprisingly then, technical issues tend to predominate when assessing the development potential of a project in the process typically referred to as ædoing a feasibility studyÆ. But the principal purpose of a æfeasibility studyÆ is to determine whether a development opportunity makes good business sense, not just whether it is technically possible. Resolution of technical issues is often seen as the primary focus of a feasibility study, whereas in reality, these technical issues are the basis upon which an asset delivery and business plan is built. This is not to say that technical issues are unimportant û they are a prerequisite to the demonstration of a projectÆs viability. The feasibility study process must therefore demonstrate that not only have the technical issues been satisfactorily addressed, but also that the broader commercial, economic and social issues have been considered in the development of a comprehensive business plan, which includes an assessment of the risk-reward profile of the proposed development. This paper will present a framework for the conduct of æfeasibility studiesÆ and provide guidance to minimum standards and best practice.

Jan 1, 2007

By R Berry, A Escolme

"Predictive geometallurgical models are being developed for the Productora Cu-Au-Mo deposit based on geochemistry to reflect variability in Cu species based on Cu sequential leach data (ie oxide, transitional-oxide, transitional-sulfide, sulfide and non-recoverable Cu).Productora, located in the coastal range of northern Chile, is a magmatic-hydrothermal tourmaline breccia-hosted, structurally controlled Cu-Au-Mo deposit hosted by a thick sequence of Jurassic rhyodacitic volcanic rocks. North and north-west striking fault sets control the distribution of mineralised breccias. Alteration is widespread, complex and pervasive. Hypogene alteration assemblages range in composition from distal magnetite-amphibole, to sodic-calcic, to sodic, to phyllic, to proximal potassic. Low-temperature advanced argillic assemblages are locally juxtaposed next to proximal high-temperature K-feldspar-tourmaline assemblages. The dominant hypogene Cu phase is chalcopyrite.A simple Cu species classification scheme based on sequential leach data and S per cent was devised to account for non-recoverable Cu (ie non-sulfide Cu), which is insoluble in weak acids. Through machine learning, a proxy for this Cu species classification scheme was developed based on: depth, Ca per cent, Cu per cent, Fe per cent, K per cent, Mn ppm, S per cent and Ln(Cu/S) plus logged regolith class, thus allowing classification to be extended to areas of the deposit where no sequential leach data are available. The modelled data has been used to generate deposit-wide 3D models for Cu species classification.The validity of the proxy Cu species classification model is being tested against the results of flotation analysis. Initial results indicate that geochemical proxies can be used to successfully predict Cu species class and provide a high density of classification data.CITATION:Escolme, A, Berry, R and Hunt, J, 2016. Predicting Cu Species Classification Using Geochemistry at the Productora Cu-Au-Mo Deposit, Chile, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 113–118 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By N Clarke, G R. Ballantyne, M S. Powell, P Elms, A Anyimadu

AngloGold Ashanti Ltd nominated Sunrise Dam Gold Mine as a case study via their involvement with the long-running Australian Mineral Industry Research Association (AMIRA) International P9P research program (AMIRA, 2015) . A group of researchers from the Global Comminution Collaborative (GCC) conducted a comminution circuit survey and review together with a large group of graduate metallurgists, senior metallurgists and operators. Fundamental and applied research understanding was used to identify productivity and efficiency improvements around the crushing and grinding circuits. The limitations of current scientific knowledge were identified through this process and this will allow future research to be more focussed on what is required by industry.The comminution circuit at Sunrise Dam comprises three stages of crushing followed by two stages of ball milling. The secondary crusher and primary ball mill classification were identified as the primary limitations of the circuit. The secondary crusher was found to be underperforming through overall equipment efficiency (OEE) analysis and an improved chamber design was identified by Chalmers University. This improved design will promote higher power utilisation, choke feeding and a finer crushed product for the milling circuit. The primary ball mill product is classified by a combination of a trommel, 3 sieve bends and a hydrocyclone. The combination of poor classification and coarse, competent feed led to a situation where the primary mill was overfilled with rocks, reducing grinding rate due to cushioning of impact. Size specific energy (SSE) benchmarking methodology was used to identify that a 10% increase in throughput could be achieved with improved primary classification.CITATION:Ballantyne, G R, Clarke, N, Elms, P, Anyimadu, A and Powell, M S, 2015. Application of research principles to identify process improvement at Sunrise Dam Gold Mine, in Proceedings MetPlant 2015, pp 221–229 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By D Connelly

There is now a new generation of mobile crushing and screening plant systems available which have been developed based on the motivation of reducing truck haulage. Newly designed mobile crushing and screening plant systems have the advantages of mobility, flexibility, economy and reliable performance, making this system very appealing for small- to medium-sized projects or projects where a number of resources are separated by distance.A brief review of the past history and experience with transportable crushing plants provides an insight into some of the issues with transportable plants in mineral processing. A closer look at a simple model based on exploiting small but high-grade orebodies suggests the concept has merit, however there are many more engineering, logistics, legal, technical and management aspects which have limited the application of such a concept in the resource sector. This paper explores the concept in detail and endeavours to analyse the preferred commodities and scenarios under which the concept could be used and the economic and logistical limitations for iron ore. The paper also looks at the risk assessment criteria to be applied in selecting the type of resource projects where the model could be applied successfully. Other aspects considered in this paper are the project planning requirements, technical and economic feasibility, bankability and operability. Reference is made to the operating experience of contractors at a number of sites and feedback from the resource companies as managers of the projects.CITATION:Connelly, D, 2013. Mobile crushing and screening plant applications for small- to medium-sized iron ore projects, in Proceedings Iron Ore 20 13, pp 349-354 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By A Rantala, J Timperi and J Kaartinen, T Maksimainen, O Haavisto

"X-ray fluorescence (XRF) is the most common technique used for online slurry assaying in base metal flotation applications. Typically, assays from feed, concentrate and tailings slurries are used to monitor and control the flotation circuit, with possible additional sampling locations in other main slurry flows inside the circuit. The elemental content detection from the XRF spectrum is relatively straightforward as the spectrum contains element-specific peaks whose height corresponds to the element concentration in the sample. However, centralised XRF analysers measure the elemental concentrations line-by-line, which may increase the sampling interval for an individual line and cause unnecessary response delays, especially in large flotation plants. Reflectance spectroscopy is an emerging technique that can be used to obtain more frequent measurements from slurries. The measurement is based on the mineral-specific absorbance of light in the visible and near-infrared (VNIR) wavelength range. Due to this relatively inexpensive and simple measurement system, it is possible to conduct the measurement simultaneously in several slurry lines. However, the information contained in the VNIR spectra is more difficult to interpret as concentrations of all the minerals in the sample contribute to the measured spectrum and changes in solids content, particle size and mineralogy disturb the elemental content estimation. Therefore, frequent calibration of the measurement is required. This study presents the application of combined reflectance spectrum and XRF measurements for rapid online slurry assaying in a copper-nickel flotation plant. The XRF assays are utilised as calibration samples for the reflectance spectrum measurement, keeping the calibration model up-to-date. The rapid reflectance spectrum analysis is then used to provide an almost continuous estimate of the slurry contents, enabling further improved process monitoring and control.Citation:Haavisto, O, Maksimainen, T, Rantala, A, Timperi, J and Kaartinen, J, 2016. Reflectance Spectroscopy with X-ray Fluorescence for Rapid Online Assaying in a Copper-nickel Flotation Plant, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 85–92 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By G D. Richmond, J C. Chomley

Copper has been mined intermittently at Gunpowder, north of Mount Isa, since 1927. Most ventures have had some initial success but fluctuating copper prices, the small-scale of the operations and the remoteness of the site led to closures or sale. Processing routes have included direct sale of high grade ore, flotation of oxide and sulphide concentrate, and copper cement production from mine solutions. Copper cathode has been produced by heap and in-place leaching coupled with solvent extraction and electrowinning (SX/EW). Aberfoyle Limited recently purchased the Gunpowder operation and is expanding operations. An innovative high recovery tank leaching process, including a low temperature, low pressure autoclave, has been adopted. Copper cathode will be produced from an expanded solvent extraction/electrowinning plant at approximately 45 000 tonnes per year. The combination of expanded throughput and high metal recoveries will make Gunpowder a cost competitive producer.

Jan 1, 1998

By D Chalmers, C C. Harb

The detection and control of gas levels in mining is a continuing challenge for the industry. Standard detectors have many problems that could be overcome with laser based spectroscopic instruments, but to date these systems have not been suitable for mining conditions. This paper reports the development of a new digital data extraction scheme to modernise traditional cavity ring down spectroscopy (CRDS). CRDS is a direct cavity enhanced laser based absorption technique, which is used to allow the identification of an unknown substance by their molecular fingerprint; this unknown substance is identified by analysing the ring downtime of the light exiting the optical cavity. Traditional CRDS has many issues when analysing substances in hostile environments, or when multiple species may be present. This presents an alternative approach, called real-time CRDS (rtCRDS) that has the potential to overcome many of these issues and produces systems that could be used in the mining industry. The system utilises newly developed widely tuning quantum cascade lasers combined with improved optical cavities and novel digital data extraction to produce spectra over a 1500 nm range in a few seconds. The ring downtime measurements produced are accurate and have high sensitivity and maximum signal to noise ratio. This paper discusses the technique, illustrating the advantages compared to traditional systems and show real-time spectra for a set of molecules of interest to the mining industry. This paper also provided an analogy between this approach and that used in digital communications systems, and shows that this scheme is ideally suited to provide a network of sensors in hostile environments.CITATION:Harb, C C and Chalmers, D, 2015. Real-time methane detection – modern digital laser spectroscopy for hostile environments, in Proceedings The Australian Mine Ventilation Conference, pp 161–166 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By M Rankin, F Medina, R Verburg

We conducted a preliminary assessment of an extensive deposit of historic tailings discharged over a period of 40 years to the shoreline along a Southern Peruvian coastline. The tailings formed an extensive beach approximately 2.4 km long and 300 m wide. The tailings consist principally of pyrite (37 to 59 per cent), hematite (nine to 20 per cent), magnetite (three to 13 per cent) and quartz (11 to 36 per cent). The present operating company was required to evaluate the feasibility of capping the ocean side tailings deposit, however, given the size of the undertaking and the potential to reclaim residual minerals from the tailings, it was prudent to first evaluate whether capping would in fact reduce the impacts to the marine environment. Therefore this preliminary assessment examined: 1. metals contamination in tailings, shoreline porewater and marine sediments; 2. reactivity of tailings and acid generation potential; and 3. the potential for biological effects from metal contamination in the uplands tailings (solid phase) and beach porewater. Based on mineralogy, column leach studies and chemical results, the upland tailings have a high geochemical potential to acidify and release metals, especially copper, nickel and zinc, should they be subject to oxygenated and aqueous conditions. But, the extreme arid climate results in very low potential for precipitation and virtually precludes the transport of acid drainage reaction products from the upland tailings towards ocean. Wind erosion caused by offshore winds is likely a small source of tailing transport to the ocean. Since some potential exists to reprocess the tailings in the future, capping does not seem justified at present.

Jan 1, 2003

By S J Riley

The cover (cap) over the tailings pit at Nabarlek uranium mine must be structurally stable as it will act as a barrier to radon gas emission and have to contain other long-lived radionuclides. Structural stability is primarily an issue of erosional stability in the context of a design life of thousands of years. The primary agent of erosion is fluvial, dominated by rainwash, overland flow, filling and gullying in the local area. Other agents of erosion are of less concern although biogenic agents of erosion (eg termites and windthrow) may enhance fluvial activity. Several methods may be used to assess erosional stability. They fall into two main categories, namely erosion modelling and geomorphic modelling. The former is illustrated by the Universal Soil Loss Equation in which parameters describing aspects of the geotechnical and hydrological properties of the rehabilitated surface are used as input for the modelling of erosion rates. The latter is illustrated by estimates of gully and valley erosion using empirical models. Estimates of the erosion rates and stability of the Nabarlek cover are presented. The two main techniques are complementary and it is argued that rehabilitation design must make use of both approaches when estimating erosion and geomorphic stability. More recent developments in geomorphic modelling using numerical techniques incorporate both approaches.

Jan 1, 1994

By R Fanni, D Reid, M Kulessa

Recent updates to Australian industry guidelines emphasise the importance of the assessment of liquefaction potential of tailings. This includes assessment of the cyclic liquefaction potential, and the post-seismic strength of tailings expected to undergo strength loss from seismic loading. Despite this increase in focus, a relatively small number of Australian tailings appear to have been characterised through cyclic and post-cyclic testing. This paper presents the cyclic characterisation of four Australian tailings, consisting of iron ore, lateritic nickel, vanadium and bauxite residue. Material was obtained either from surficial tube sampling or through remoulding samples in the laboratory from slurries. Testing consisted of monotonic, cyclic and post-cyclic tests for each material. For three of the materials, laboratory-scale shear vane testing was also performed to provide a comparison to post-cyclic strengths from direct simple shear.The results indicated cyclic resistances consistent with the results of other tailings presented in the literature. The lateritic nickel tailings provided the greatest cyclic resistance of the four materials tested, followed by the vanadium tailings. This was somewhat consistent with expectations for material behaviour based on index properties. Post-cyclic strengths were seen to decrease as cyclic strains increased, consistent with typical observations in the literature. Following significant cyclic straining, in some instances the post-cyclic strengths approached those obtained through residual shear vane testing. This provides further insight into the strain-dependent nature of post-cyclic strengths for some materials. The implications of these observations on the post-seismic stability condition are discussed.CITATION:Reid, D, Fanni, R and Kulessa, M, 2015. Cyclic and post-cyclic behaviour of four Australian tailings, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 207–214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

Thermodynamics of Non-Cyanide Gold Solvents The present status of the raw material base in the gold industry requires specific ways to recover gold and silver from ores. Most gold is closely associated with sulfides which require flotation followed by pressure or bacterial oxidation. The next stages of processing usually require using expensive operations for the preparation of leaching. A lot of researchers want to find a new alternative solvent for the extraction of precious metals from these products. According to the authors, one of the best ways is to use sulfur-based solvents (thiosulfate, sulfite, and their various mixtures). Thermodynamics of gold and silver thiosulfate dilution are calculated for conditions: the concentration of Au - 200 mg/L, oxygen - 3.2 mg/L, thiosulfate - 79 mg/L, OH- - 170 mg/L. the general result is the possibility of process remains under standard conditions. (erAu = = 0.035 V, ?G298 = - 29.18 kJ/g-atom ??). Silver with thiosulfate forms two strong complexes: [AgS203]- and [Ag(S203)2]3-. ?G0 = -1027 kJ/mol. The complex [AgS203]- is less stable: ?G0 = 486 kJ/mol. It should be noted that despite the high stability of gold complexes, the sodium thiosulfate may decompose to sulfite and elemental sulfur during the process, especially when heating. Gold is slightly soluble in the sodium sulfite solution, however it forms the strong complex [Au(SO3)2]3-. Depending on the concentration of free S2O32-ions, silver with sodium sulfite forms three complexes: [AgSO3]-, [Ag(SO3)2]3- and [Ag(SO3)3]5-. The dissolution speed of gold in sodium sulfite solution may be in the same range as it is during cyanidation. In this case, a practical application of sulfite process can be also used, especially for the products containing free elemental sulfur. In conclusion, sulfite-thiosulfate gold lixiviants can be used for concentrates after pressure oxidation of the cakes.

Sep 13, 2010

This paper presents an overview of a program PC-BC developed for application to the design and evaluation of block cave operations. Conventional mine planning software tools are not well suited to the evaluation of this type of deposit. The paper looks at the modelling approach as applied to a block cave mining project. The following steps are described:Initial preparation of data including block models, draw point footprint geometry and draw cone geometry. Computation of individual draw point reserves. Procedure for modelling of vertical mixing of material within each draw point and subsequent determination of the best height of draw for each draw point based upon an economic cut-off value. Smoothing of draw heights amongst neighbouring draw points to produce a realistic draw envelope. Mineable reserves within the envelope are then computed. Tools for preparation and evaluation of various production schedules. This includes definition of draw rates, and rates for commissioning new draw points. In an operating mine, the capture and analysis of daily draw tonnages is important. How PC-BC accommodates this is described as well as the processes for depleting the draw column reserves. In the 12 years since the program was first developed, it has been used on a number of projects for feasibility studies and operating mines. Some practical examples of the use of the program in these projects are presented. Finally, some commentary on the sensitivity of various parameters is presented. Particular emphasis is placed on the overall footprint design.

Jan 1, 2000

We all live in professional silos û comfort zones, where we talk to like-minded people with the same training, experience and view of the world. We note in passing the existence of other disciplines, but they are tolerated rather than embraced. To the geologist, the metallurgist is a mad scientist conjuring gold out of some foul solution about which the less said the better. To the metallurgist, the geologist is a bearded, self-appointed sage who guesses what is under our feet by sniffing the air, and drives a Land Rover badly. As to the view of mining engineers held by both geologists and metallurgists, this is best left to the imagination. And of course we are all confused by the term æmetallurgistÆ. I am called a metallurgist though my skills are in mineral processing not metal processing, but I canÆt be called a mineralogist because that definition is already taken. *Please note that this is available as an extended abstract only*

Jan 1, 2005

By R Ibarra, H Solis, G Teowee, B E. Papillon

The authors have previously described a piezoelectric-based system to measure the dynamic pressure during actual detonation in the field. This technique is used in a water hammer test set-up where a donor detonator is fired first, with the pressure sensor and an acceptor electronic detonator placed underwater in a water tank, and maintained at a fixed distance away from the donor detonator. The functioning and timing of the acceptor detonator are captured using a customised microcontroller board called the water hammer timer. Using such water hammer testing, the effect of dynamic pressure was studied as a function of the magnitude of pressure during the electronic timing countdown. Data obtained indicate there is no significant impact in the timing of the electronic detonators in contrast to what has been reported in non-electric detonators.CITATION:Teowee, G, Solis, H, Papillon, B E and Ibarra, R, 2015. Effect of dynamic pressure on electronic detonator timing, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 575–578 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015