Search Documents

This paper summarizes the progress of geological exploration at North Broken Hill Ltd.The North Mine orebodies occur in knots of minor folds on a simple limb structure which is itself highly folded, giving rise to two distinct orebodies pitching N. at av. 42° down to 2,920-ft. level, where the pitch steepens to near vertical as a result of complementary shear movement on the Globe-Vauxhall Crush Zone.The lack of adequate marker beds and top and bottom relations makes the resolving of the complex structural environment of the orebodies most difficult.To test the deeper ground of each side of the De Bavay Fault on the 2,600-ft. level the footwall drive was extended 3,556 feet and over 20,000 ft. of drilling completed from three transverse fans, only one of which intersected the orebodies due to steepening of pitch.The problem of locating the North Mine orebodies N. of the DeBavay Fault remains speculative because the exact position of them S. of the fault is still unknown. Exploration beyond the fault in the search for ore had two lines of mineralization to consider, an eastern one through Cosgroves-Round Hill, long regarded as the continuation of the main lode, and a western one passing through Silver Hill Silver Peak.From surface 45,000 ft. of drilling was completed in five sections, establishing that the structure was dominantly synclinal with a flatdipping E. limb, the W. limb and adjoining structures being involved in the Globe-Vauxhall Crush Zone. Mineralization, though weak, was remarkably persistent but the economic mineralization exposed at surface has not persisted with any continuity.Deep exploratory drilling below the bottom level (3,370 ft.) has established high-grade ore to a depth of 4,095 ft. and also has proved its existence within the Globe-Vauxhall Crush Zone.INTRODUCTIONThis paper summarizes the progress of geological exploration at North Broken Hill Limited from the inception of the Geological Department in 1941 until the end of 1955. The writer has drawn freely on departmental records for the period prior to 1947.

Jan 1, 1956

Six years ago it was my responsibility to give the presidential address, and now that privilege has come my way again. On that occasion we were gathered atWhyalla and I took the opportunity of putting before members some observations on the problems we then faced in Australia, and some gains we had been able to chalk up during those early postwar years. You may recall that we were then just beginning to emerge from the difficulties of postwar reconstructions - of fuel and power shortages, and a grossly inadequate manpower for the tasks facing us. The expansion of manufacturing industry in Australia greatly stimulated by wartime activities, and by the postwar developments of many institutions - ran ahead of the supporting services and of the supply of labour to do thejobs. For many industries this unfortunate state of affairs had meant operating at rates well below their installed capacities and therefore levels of output insufficient for Australia's rapidly growing needs. When I last spoke to you these problems were still with us, though their intensity was beginning to lessen as a result of vigorous efforts by industry and governments to reduce them. But I must confess that my thoughts on that occasion were full of those problems and of the effect they were having on the iron and steel industry of this country-of the coal shortage, the labour shortage, and the many other difficulties we were then faced with - and all at a time when the stepping up of our postwar expansion programme was of vital concern to all of us.What a different picture it is six years later! How greatly has the scene changed for the better. In 1951 Australia's postwar immigration programme was only in...

Jan 1, 1957

By E L. Kotova

Completeness of extraction of a mineral from ore depends on many reasons. First of all it is a function of quality of disintegration of ore. It is supposed that two basic factors: character of structure and texture of the ore aggregate and a disintegration technique influence the quality of the mineral aggregate destruction, æopeningÆ of its internal boundaries. In this paper, the problem of technological mineralogy from the point of view of genesis of the mineral aggregate, its typomorphical features and methods of their quantitative description are discussed. The purpose of this research is to provide information for technologists. It should enable the development of a rational flexible scheme of disintegration of ore with full extraction of a useful component, without its losses and without unnecessary expenses of energy. For achievement of this purpose the mineralogical information should have ½number and a measure+. By the authors, the technique of the quantitative analysis of fabric of the mineral aggregate based on several models û thermodynamic, crystallographic and geometrical is offered and discussed. The leading role in the quantitative analysis of a fabric of ore belongs to internal bounders. But internal bounders of the mineral aggregate by bounders or faces of the mineral individuals or mineral grains are formed. Their geometry, orientation concerning own (mineral grain) crystallographic lattices, orientation and distribution in space of the ore aggregate are proportional to the energy accumulated at origin and the further growth. These characteristics of mineral individuals are consequences of conditions of their formation. That is why the named triad of models is used. From crystallography it is known that faces of different stability and mobility form borders of crystals. They also contain different quantity of energy. Mineral grains also are faceted by different energy borders. They form intergrowths with each other according to a principle of balance or unbalance. That is why in addition to traditional parameters of the description of a fabric of the mineral aggregate (mode and grainmetrical composition) it is necessary to add new. For example, length and the square of intergrowthing bounders of mineral individuals differentiated (in couples), crystallographic symbols of borders, their roughness and so forth. Consequently, solving a problem of the geometrical characteristic of borders, we define also its power characteristic. In this paper experience of application of our technology in studying ores of one of deposits of Urals Mountains is presented. For realisation of these types of the analysis technologies of measurement, the program of calculation and the devices, which are carrying out the analysis in a semi-automatic mode, are possessed. Structure and texture of rock or ore aggregate reflect its formation and transformation conditions. It is important to understand that disintegration energy cannot be more than aggregation energy, the energy of intergrowths formation. The square and orientation of mineral individuals borders vary at pressures or stresses of mineral aggregate evolution. These phenomena often cause selective increase in the square of borders at constant average grain size, ie the granulation. Granulation presents the increase in quantity of mineral individuals while their modal share remains constant. At the same time their average mineral grains size. Some mineral individuals increase in size at increased pressure. When lithostatic or lateral pressure drops the majority of mineral grains increases in volume at the cost of intersticial or film solutions or fine grains. These are only special examples of the ontogenesis of the mineral aggregate. They illustrate our statement that all changes in fabric of the mineral aggregate are a reaction on varying external (ie geological) conditions. It is possible to consider that structurisation of totality of mineral individuals as a whole is a process of adaptation of the mineral aggregate, which forms and exists in varying force and energy fields. Differential and integrated geometry of total internal boundaries of the mineral aggregate serves as adaptation mechanism of the mineral grains system. Boundaries form intergrowths of the mineral aggregate. Thus, it is possible to consider that the most informative parameters of the stereometric analysis for restoration of the ontogenesis of the mineral aggregate are the following. First of all, it is a quantitative estimation of the volumetric shape of the ore mineral in crystallographic coordinates, a total area of borders of all mineral grains in the aggregate, the specific square of their boundaries, the specific square of intergrowth boundaries of the ore mineral separately with grains of each minerals of the matrix of the mineral aggregate as well as traditional grainsmetric and modal composition. For realisation of these types of the analysis technologies of measurement, the program of calculation and the devices that are carrying out the analysis in a semi-automatic mode are possessed.

Jan 1, 2008

By Lawson F

Pyrite concentrate and calcine from the Nanjing Lead-Zinc-Silver Mines, China, were leached with aqueous cyanide and thiourea solutions. More than half of the contained gold and silver was able to be extracted from the roaster calcines. The very fine dissemination of precious metal grains, high roasting temperature (850 - 900°C) and residual sulphur are believed responsible for the Iow extractions.A recovery of about 70 per cent for both silver and gold was able to be obtained with cyanide and with thiourea leachants when the pyrite was roasted in the laboratory at temperatures between 600 and 650°C.Thiourea, as an alternative leachant, has received much attention recently and a series of constant potential leaching tests was conducted.When the thiourea to formamidine disulphide mole ratio was about two, the precious metal extraction was greatest. In the Nanjing calcined material, this occurred at a potential of about 210 mV relative to a standard calomel electrode.

Jan 1, 1987

By J Thoma, W Skinner, W Stewart, R Smart

The acid neutralisation capacity (ANC) of rock sample containing significant iron carbonates and/or reactive framboidal pyrite can be a difficult parameter to determine. Results indicated that negative ANC results can occur if reactive sulfide minerals are present; and an over-estimation of ANC will result if significant Fe rich carbonate minerals are present during industry standard ANC tests. In this paper we investigate these problems. Results showed that a significant lag period may be needed (up to 432 hours) after standard Sobek ANC type tests of siderite for the complete hydrolysis of iron released from this mineral. This even occurred with standard industry modifications that included the addition of two drops of hydrogen peroxide. In this work we use a modified Sobek test that included filtering, and thence continued hydrogen peroxide addition until there was no subsequent pH drop, followed by back titration to pH 7.0. Results indicated that the ANC for the siderite (after zero hours) was immediately comparable to the ANC determined after 432 hours lag by standard Sobek type tests; and a calculated theoretical carbonate ANC. Investigations of coal waste samples containing significant framboidal pyrite indicated that standard Sobek ANC type tests can result in negative ANC values due to the oxidation of this reactive pyrite. Because sulfide acidity is already addressed by the MPA calculation, the inclusion of sulfide acidity as part of the ANC determination is effectively biased towards acid generation and thus positive NAPP values. Negative ANC values cannot be ignored or assumed to be zero as this masks any actual ANC available within the sample, which may possibly affect AMD categorisation. This sulfide acidity can be factored out using the quantity of S in the ANC digestion liquor and knowing the non-acid generating sulfate content of the sample prior to ANC testing. Results indicated that incomplete iron hydrolysis at the completion of the Modified Sobek ANC test is not only a function of iron carbonate dissolution, but is also related to the dissolution of Fe-sulfate salts, and the oxidation of reactive sulfides such as framboidal pyrite.

Jan 1, 2003

By D Michaelsen, S Miller

The Grasberg Mine is a copper and gold open pit mine operated by PT Freeport Indonesia (PTFI) and located in the high equatorial mountains of the Indonesian province of Papua. The climate is alpine/subalpine with little seasonal variation in temperature or rainfall. The daily average temperature ranges from about 2¦C to 14¦C and the annual rainfall in the vicinity of the mine and overburden stockpiles is about 4000 mm to 5000 mm. Mining of the Grasberg open pit will continue until 2014 at which time approximately 2750 Mt of overburden will have been produced. Current overburden production rates are 200 Mt per annum. The current mill rate is 230 000 t/day from the Grasberg pit (190 000 t/day) and the underground operations (40 000 t/day). The acid rock drainage (ARD) issues associated with overburden from the Grasberg operations were identified early in the mining operation. Almost all overburden placed to date has been Potentially Acid Forming (PAF). Laboratory testing has identified four main overburden types: limestone and non-acid forming (Green waste), PAF low capacity (Blue waste) and PAF high capacity (Red waste), and Heavy Sulfide Zone (HSZ), which contains greater than 20 per cent pyrite. Waste type block modelling indicates that at least 30 per cent of the overburden production from 2003 to the end of Grasberg pit operations will be limestone. Strategies are being developed to maximise the beneficial use of limestone through strategic blending and placement for ARD mitigation and control.

Jan 1, 2003

Commercial explosives range from pure emulsions to pure ANFO, with blends of these providing interesting alternatives: energy is often adjusted through addition of aluminium, or the control of density. The energy rating of explosives is derived chiefly from detonation codes, which are used to derive expressions for the internal energy change of the detonation products as they do work under expansion. While all codes used for this purpose work on the basis of Ideal detonation, it is common knowledge that commercial explosives operate in the Non-Ideal domain, which affects the mode of energy delivery to the environment. However, since Ideality represents the foundation from which actual performance evolves, it is valuable to examine the intrinsic energy release of a formulation before attempting to understand the influence of Non-Ideality. In examining the Ideal pressure profile of fundamental formulations, remarkable correlation has been found with field performance, and this increases understanding of the influence of various formulation modifications, especially in regard to the stage at which energy is released, and the effect on rockbreaking. This work has emphasised the value of attempting to understand and define better the non-ideal detonation process.

Jan 1, 2001

By S Cossfo Torres

Minera PenmontÆs gold mine, La Herradura, is located at the northwestern Mexican state of Sonora and consists of an open pit mine and heap leaching facility for the recovery of gold. The production began in July 1998, and today La Herradura produces about 200 000 oz of gold per year. Standard sampling and assaying protocols were established during exploration based on heterogeneity tests. However, at deeper zones of the pit, coarse gold became evident and it was necessary to develop a new sampling protocol in order to minimise the fundamental error and improve the metallurgical accounting. This new sampling protocol requires cyanide leaching the whole pulverised sample from the blasthole, assaying pregnant solution and fire assaying 50 g of tailings. A sampling study was performed on 195 blasthole samples analysing gold under the standard and new protocols. The new protocol demonstrated that the original one underestimated gold grade by approximately 27 per cent, with impacts on ore misclassification and metallurgical accounting. According to the ore grade control system, mineral with gold grade above 0.35 g/t was sent to the leach pad and mineral with lower grade was classified as waste. Based on the sampling study, it was decided to classify a low-grade ore with gold assay between 0.20 and 0.35 g/t which was stored for future treatment under better gold prices or should mine production decrease. These two conditions were present during 2005 and 2006, when about 3.5 Mt of low-grade ore were leached.

Jan 1, 2008

By M I. Pownceby, C M. MacRae, A Torpy

Electron probe microanalysis (EPMA) and quantitative X-ray diffraction (QXRD) techniques are capable of providing high-quality quantitative information regarding the phase mineralogy and distribution of alumina within iron ore samples. The techniques, however, use different methodologies in determining the mineralogical information (ie structural versus chemical), which introduces some limitations. In this study, EPMA was used to identify and quantify the deportment of alumina within mineral phases in iron ore samples (-1 mm crushed) sourced from different suppliers. Results were directly compared with quantitative mineralogical data derived from QXRD to provide an evaluation of the relative merits of both techniques. The four ores studied contained alumina either in the form of gibbsite, aluminosilicates (eg kaolinite), or associated with goethite.For minor phases, gibbsite and kaolinite, the abundance trends measured via QXRD were generally reflected in the EPMA data. Agreement was less satisfactory for the more abundant goethite phase (both low- and high-Al forms). The discrepancy may be the result of sampling issues arising from textural features such as grain size, and also a systematic overestimate in the amount of Al-rich goethite when hematite and Al-bearing phases are finely intermixed and the EPMA step size is coarse. A second difference in the EPMA results compared to the QXRD data was in regard to quantification of low-Al and high-Al goethite phases. The sensitivity of the chemical-based EPMA was better for distinguishing between high- and low-Al goethite although the results remain overprinted by potential errors introduced via sampling.Care should be taken when directly comparing results from each method, although in general the data should be considered complementary, as each approach provides slightly different results and interpretations regarding the overall mineralogy.CITATION:Pownceby, M I, MacRae, C M and Torpy, A, 2017. A comparison of X-ray and electron-based analysis techniques for characterising the mineralogy and alumina distribution in iron ores, in Proceedings Iron Ore 2017, pp 593–598 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

The distribution of tin and iron between slag and metal phases at about 1150°C was studied in pot scale experiments. The distribution coefficient k = (Sn/Fe) In metal X (Fe/Sn) in slag was found to vary from about 300 for metal corresponding to nearly pure tin, to about 100 for metal of about miscibility gap composition (17' 4 per cent Fe). Results conformed reasonably well to a straight line relationship between log k and (l-2NFe), as expected on theoretical grounds, and are consistent with thermodynamic data for the Fe-Sn phase diagram and the reaction Fe + SnO = FeO + Sn.Calculations are presented indicating the feasibility of smelting low-grade tin concentrates in a two-stage counter-current reduction process.

Jan 1, 1966

By Knevitt L. T

PART 1Details of Kiewa Scheme.Introduction.Topography.Preliminary Investigations.Geology.Description of Project.Details of Main Works.Main Transmission of Power.Construction Facilities.PART 2Underground Works.Summary of Projected Works.Administration.Labour.Surveying.Safety and Accident Prevention.Medical Attention and First Aid.PART 3No. 4 Head Race Tunnel.Summary.Geology.

Jan 1, 1950

By Johnston W. H

MINING operations in the Waihi mine began, under the present proprietorship in the year 1889. Previous to this, and as far back as the year 1880, the presence of reefs in the Martha Hill had been known, and surface working on a small scale had beencarried out, without any great measure of success. The only method of treatment in use at this time was the old system of light stamps, amalgamating tables and berdans, and recovery by this method being low, little margin for profit was left, so thatthe property in these days was not considered of great importance and work on the area was only carried on spasmodically by different owners.On the transfer of the leases to the present company, calcining, dry crushing, and hot pan amalgamation was adopted as the method of treatment, and this system was continued till the more modern cyanide process was introduced and applied. As themethods of treatment and gold-saving became more efficient with the application of more modern and scientific processes, the importance and future prospects of the mine became more and more pronounced, and mining on a larger and more comprehensive scale was gradually established.As in the case of ore treatment, mining methods in the early stages were not as far adv.anced as the adopted practice of today, and numerous shafts, levels close together in vertical height.

Jan 1, 1912

Jan 1, 2004

By M Bourke

Modern computers and software provide powerful tools for the geologist to construct reliable models of geological resources, and the mining engineer to produce accurate and workable mine plans. Over the years many people have developed a phobia of computers, especially for geological analysis, modelling and mine planning. This phobia is often caused by a lack of knowledge, poor training or a bad experience. The adoption however of computers for geological modelling and mine planning is now becoming mainstream. With the correct training, a good understanding of input data, and detailed knowledge of the required results, the phobia can safely be overcome to provide mining operations with increased productivity.

Jan 1, 1999

Radioisotope x-ray methods for the on-stream determination of copper, lead, and zinc in mineral product slurries were developed, and were successfully tested at the plant of Cobar Mines Pty. Ltd.The tests were made in three stages. Measurements to determine the precision of analysis were made initially on briquettes of the mineral products. The effect of slurry solids content variations was then determined by measurements on the mineral products in a recirculating slurry loop. The radioisotope analyser was finally tested in a series of on-stream measurements in the plant.Copper, lead, and zinc in flotation feed and in copper concentrate were determined to a precision ranging between 1·4 and 15 per cent of the mean element concentration in the slurry solids. These precisions are within limits required for plant control purposes at Cobar.

Jan 1, 1971

Few, if any, reliable thermodynamic data are available for the activity of tin oxide in slags. In this work, the activity of the oxide in silica saturated iron silicate slags has been measured at 1573 K using the equilibrium Sn (alloy) + Y2O2-SnO (slag).Slag and a Ag-Sn alloy were sealed in a zirconium oxide crucible to prevent the escape of volatile tin oxide, and the oxygen pressure at equilibrium measured in situ using the zirconium oxide as a solid electrolyte. Activity of tin was calculated from known data for the Ag-Sn system and activity of tin oxide calculated from free energy data. The results have been extrapolated to predict the industrially important distribution of tin and iron between Fe-Sn alloy and iron silicate based slags.

Jan 1, 1983

By B Mead, N D. Pascoe

The Grasberg block cave rail haulage system will be located in the Grasberg mining district on the island of Papua, Indonesia at an elevation of almost 3000 m above sea level. It will transport 160 000 t of ore per day from multiple chute galleries to the underground crushing systems. The design entails approximately 23 km of rail (ballasted and embedded track), over 120 ore chutes to deliver ore to the muck cars and three unloading stations to deliver ore to the crushers. The rail haulage system is a closed-loop system entirely within the underground mining complex.The GBC rail haulage project will be a substantial operation. Trains consist of 11–12 bottom-dump 20 m3 muck cars driven by a 40 t electric locomotive, about 400 t per trainload. Approximately 12 trains and one spare are required to maintain full production at 160 000 t/d. All rail installations will be 1435 mm (standard) gauge with AS60 steel.The rail system is designed to operate in full automated mode, including chute loading, hauling and dumping. The operation will be controlled from a surface control room.The rail haulage project has been divided into five stages, which will be brought online over the course of ten years. Current development and construction are focused on Stage 1 for initial production that will occur beginning in late 2017. This stage includes 24 chutes in three chute galleries, one unloading station, workshop areas and almost 7 km of track (3 km of embedded and 4 km of ballast).This paper describes the key components of the rail haulage system and reports on the current status of development and construction of the system. This paper also overviews the challenges, successes, issues and risks of this project in areas such as scheduling, development, construction and operation.CITATION:Pascoe, N D, Mead, B and Vega, H, 2016. Grasberg block cave haulage project – design and construction update, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 585–598 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Our modern cities are almost incapable of sustaining themselves without subsurface infrastructure, which is not identifiable at first glance. This very soon becomes evident when the chaotic conditions prevailing in some cases in the multi-million cities on the African, Asian and South American continents are taken into consideration. This does not simply apply to the hopelessly congested streets in the downtown areas. If anything, it is shown here too that a subsurface infrastructure represents an important prerequisite for public health right up to banishing the danger of disease. Even during the 1990s, this has been clearly underlined through examples of cholera and plague epidemics in parts of Central and South America as well as on the Indian subcontinent. The overriding significance of an inner urban subsurface infrastructure in order to create decent conditions in the major built-up areas was once again emphasised not all that long ago at the United Nations HABITAT-II Conference in Istanbul, Turkey, in June 1996. More than 15 000 delegates from all over the world mulled over and discussed the prerequisites for humane living conditions in human settlements taking the varying climatic, topographical and cultural marginal conditions in different regions of the globe into account. Apart from the built-up areas themselves, the utilisation of underground space is experiencing high and ever increasing significance in less densely populated regions. Attractive and fast transport links between industrial centres call for high- performance transport arteries for the economic, speedy and unhampered carriage of people and goods. Important impulses for the economic power of a region or nation are provided by transport development and links. As a consequence, tunnels for roads and railways are being built or planned to a great degree for crossing mountain ranges, rivers and straits.

Jan 1, 1999

The general principles of technical due diligence best practice that are involved in assessing a mineral property in the early stages of its development are described and a bibliography of relevant papers is attached. The issues specific to the evaluation of gold deposits are highlighted. The Australasian Institute of Mining and Metallurgy's (The AusIMM) initiatives in this area, dealing with the proper public reporting of Reserve/Resource information (JORC Code) and property assessment/valuation (VALMIN Code), will be used as a framework against which the illegal tampering with drilling samples to artificially boost their gold content (salting) from the Busang gold deposit (Kalimantan, Indonesia), owned by Bre-X Minerals Limited (Calgary, Canada), will be reviewed. While the Busang saga was based upon fraud, through salting the samples, the general lessons to learn from such a scam are worth documenting. In Australia, most of those working in the mineral industry belong to long established professional institutes and consultant associations (eg The AusIMM or Mineral Industry Consultants Association [MICA]) that require their members to work within their technical limits and to comply with best practice guidelines, or risk being judged and found wanting by their peers in the context of strong Ethics Codes. There is also a strong interface between such representative professional bodies and the corporate and financial market regulators (ASC/ASX), which closes the monitoring loop. Canada has only now seen the wisdom of having this type of early warning system in place. Fraud and deliberate deception will be always possible, but deception on the enormous scale that occurred at Busang is most unlikely with proper surveillance systems in place and the use of accredited technical professionals. There should have been more hard data available about so big and rich a deposit owned by a C$6Bn company.

Jan 1, 1997

By Lyon R. J P

The quartz-cassiterite-wolfram veins at the Aberfoyle Tin Mine, north-eastern Tasmania, form a sheeted zone about 200 ft. wide and 1,600 ft. long in slightly contact metamorphosed shales, slates and greywackes, and are associated with a cupola of aplitic granite whose top is about 1,050 ft. below the present surface. Economic mineralization persists from the surface down to a vertical depth of 1,050 ft. to 1,100 ft., dying away in the vicinity of the cupola. Down to the 9-level there is a progressive increase in wolfram content of the veins, and a decline in cassiterite content, with increasing depth.The veins are banded or zoned, with a seivedge of muscovite on the wall. Cassiterite, wolfram and sphalerite occur inside the selvedges, projecting into a core of quartz of varying width. Other sulphides form the central part of some narrow veins, or occur as clots in the quartz. The general sequence of deposition of the ore minerals was: (1) cassiterite, wolfram; (2) arsenopyrite, pyrite, molybdenite; (3) pyrrhotite (in part); (4) blende-group minerals-chalcopyrite, sphalerite, stannite, pyrrhotite (in part)-as solid solutions; (5) galena, tetrahedrite, matildite, native bismuth, scheelite; (6) marcasite and secondary pyrite, magnetite and hematite. The sequence of deposition of the gangue minerals was: (1) fluorine-bearing minerals-muscovite topaz, apatite, triplite, fluorite-more or less contemporaneous with the cassiterite and wolfram;' (2) quartz-contemporaneous with the earlier sulphides; (3) carbonates--contemporaneous with the later sulphides. The stages overlapped somewhat.The composition of the sphalerite and heat treatment experiments with the solid solutions indicate that the blende-group sulphides were deposited at about 6000 C., and cooled rapidly, so that unmixing of the solid solutions was arrested. This accords with the likelihood that the country rock temperature was not above 2000 C. Annealing experiments at between 3500 C. and 6000 C. led to further precipitation from solid solution at the lower temperatures, and to significant segregation by solid diffusion within, a week, indicating that both deposition and cooling of the ore were rapid processes-completed in a matter of days. Since the mineralizing solutions must have lost some heat during...

Jan 1, 1957