Search Documents

By K J. Davey, J T. Woodcock

Australian steelmakers produce up to 30 000 t/yr of electric arc furnace (EAF) dust. Current disposal techniques include sending EAF dust to landfill, stockpiling, and paying zinc smelters or registered waste removalists/processors to take the dust. Many of the complex overseas pyrometallurgical and hydrometallurgical treatment routes cited in the literature are not considered economic. Governmental, environmental and social pressures on producers to consider more sustainable disposal options are mounting, and there is now a strong push to consider recovering potentially valuable or recyclable components, such as zinc and iron units, from EAF dust. As well, there remain strong economic drivers for producers to find lower cost disposal solutions. Characterisation studies undertaken at CSIRO Minerals have revealed important physical differences in the nature of the zinc- and iron-bearing phases contained in domestic EAF dusts. These differences have been exploited using simple and cheap mineral processing techniques such as water washing, wet cycloning and wet magnetic separation. This has allowed a significant upgrade in the zinc content of EAF dust to be achieved, together with a reduction in the levels of key smelter penalty elements, such as chlorides and fluorides. The zinc-rich portion of the dust is now a more attractive smelter feed while the iron-rich part of the dust could potentially be briquetted or pelletised with a reductant and recycled to recover iron, and thus close the loop on dust processing. The basis of the separations tested together with laboratory results from several Australian dust samples are presented and discussed in this paper.

Jan 1, 2006

Important factors in dredge design are the estimation of total head, and the determination of flow in and around suction nozzles and in pipe lines. Total head for the dredge pump is calculated from velocity, static, and friction heads. Flow into suction nozzles depends on whether hydraulic jets or mechanical cutters are used, and on nozzle shape. Design of pipe lines depends on the transportation characteristics of the pulp, skin friction, swirl, and the avoidance of cavitation. Measurement and control of flow is important.INTRODUCTIONEconomic deposits of heavy minerals along the east coast of Australia occur in frontal dunes, which are normally unconsolidated and granular, or in hind dune areas which may contain indurated seams interspersed with loose material. In working frontal dunes, dredging depths are usually shallow since values do not persist for more than a few feet below sea level. However, the controlling factor in dredging the hind dune areas is the level of the water table and suction dredges may be designed to mine to depths of 120 ft, or even more, if necessary.In previous applications of suction dredges in the industry attention was directed primarily towards production and there was only limited research on fundamental techniques. However, with lower grade deposits now forming the major ore reserves, production levels and profit margins will fall unless more efficient dredges are developed.For satisfactory design of dredges it is essential that the total head be accurately estimated and that detailed information of the principles of flow in and around suction nozzles be determined. This paper presents information gained from field experience and laboratory investigation on these aspects.

Jan 1, 1962

By D S. Clarke, K B. Sporli

The Thames Goldfi.eld has been a major gold resource in the west of the Coromandel Peninsula, New Zealand, with the Waiotahi quartz vein system forming a large part of the field. Mineralisation is hosted by hydrothermally altered Miocene andesitic volcanic rocks. Both massive columnar-jointed and fragmental volcanic rocks are present. The vein system is dominated by the steeply dipping NE striking Waiotahi-Cambria vein, and associated splays. Hydrothermal alteration increases in intensity from isolated blocks of propylitic altered andesitic material, into the intensely clay altered equivalent. Low rank propylitic alteration is typified by chlorite, calcite and pyrite, with local illite or epidote. Clay alteration is characterised by illite, quartz, kaolinite and pyrite. While broadly forming halos around veining, intense clay alteration also occurs in strongly jointed portions of the hostrock.   Vein textures and the intense illitic clay alteration at Thames are similar to those in some of the other epithermal gold deposits of the Coromandel Volcanic zone, and in deposits of the Philippines, all related to andesitic terranes. Possible causes for textures and alteration being different in these deposits from the more classic Quartz-Adularia-Illite type epithermal systems may be that cooling/mixing rather than boiling dominates fluid evolution. Kaolinite may be also be a product of either of these different fluid types, or has resulted from overprinting of an illitic assemblage by downward percolation of acidic fluid.

Jan 1, 1991

A comparatively new and very promIsmg field for applying cemented tungsten-carbides is in the mining and quarrying industries. The economic advantages of this unique engineering material over the conventional hollow drill steel, or steel detachable bits, have proven so great that the use of "hard metals" promises, in some instances, to revolutionise the drilling of all manner of minerals. Early in the war years the Germans realised the tremendous advantages cemented carbides offered for holing hard rocks, and they proceeded to develop detachable percussion bits to do this work, at the same time evolving fast, comparatively light-hitting driliing machines, especially designed to suit the mechanical properties of the carbide.Here in Australia also, it has appeared that the detachable percussion bit offers the greatest economic benefits to consumers, although the author is well aware that carbide-tipped drill rods have, and may continue to work out satisfactorily in certain mines and quarries.Most drilling equipment at present installed in Australia may be described as being of the heavy hard-hitting variety, so that the designer of an efficient percussion bit has to take special precautions to overcome the problem of fatigue, and to ensure that the inserts are securely mounted in the body with the minimum of internal stress in the carbide.

Jan 1, 1950

By M Darvall And R Fare, D Dormer

The Argo Archaean lode gold deposit is hosted within a structurally complex shear zone system, 70 km south of Kalgoorlie, and 3 km west of the crustal-scale Boulder û Lefroy Fault. Argo is an active underground mine currently producing at a rate of 120 koz pa with a Probable and Proven Reserve as at December 2005 of 2.19 Mt at 5.94 g/t Au (419 koz), a reduction on the December 2004 Probable and Proven Reserve of 4.58 Mt at 5.74 g/t Au (845 koz). This Reserve is hosted in six separate gold bearing lodes within the Argo shear system. Presently, a further six subeconomic shears are recognised. The 2005 Reserve figure represents a reduction of 426 koz compared to the 2004 Reserve as a result of a thorough review of the geological interpretation/resource model, and engineering factors applied to the Resource/Reserve, and depletion due to mining. Year on year Resource/Reserve figures at Argo had gradually increased as additional information on the system became available and mining methods were increasingly resolved with early production. The portal for Argo underground mine was cut in June 2002 within the highly profitable Argo open pit. The proposed æAvocaÆ bottom-up mining method required extensive lead time between development and the commencement of stoping in April 2004. During development considerable additional complexity in the Resource was encountered. Additional structures were identified, and complex splay interactions affecting the geology impacted on development. Intensive concurrent exploration in the footwall to the main lode during this period was the main cause of the increase in the Resource/Reserve figures during early development. As development progressed, lower grade continuity was observed than was previously interpreted. At the same time, drilling of deeper portions of the deposit and subsequent reinterpretation of the geological model significantly reduced strike lengths of economic mineralisation. Radical changes to the mining methods were required to improve productivities and to satisfy geotechnical considerations. The changes altered the engineering factors applied, which resulted in a reduction in the Reserve figures.

Jan 1, 2006

By K Shannon, A Shaw

The Hilton and George Fisher deposits occur 22 and 24 km north of Mount Isa, NW Qld, Australia respectively. Both deposits occur as deformed Proterozoic, sediment hosted, stratiform orebodies hosting Pb-Zn-Ag (Hilton) and Zn-Pb-Ag (George Fisher) mineralisation. The two deposits are separated by approximately 2 km of strongly faulted barren shales, mudstones and siltstones along strike. Despite this, correlations between the Hilton and George Fisher deposits have previously been assumed on the basis of textural, lithological and geochemical similarities, but previously lacked specific details to prove exact stratigraphic matches.Feasibility drilling allowed broad correlations based on the position of siltstone pillars separating individual orebodies. However the position of continuous potassium-rich, siliceous and cross-fractured tuffaceous marker beds (TMBs) often used as stratigraphic markers within the Hilton Mine were initially unrecognised within the George Fisher stratigraphy where they are erratically silicified and often not cross-fractured resulting in correlations being difficult to prove. As a more detailed knowledge of TMB locations at George Fisher was gained it was possible to look for corresponding TMBs within the Hilton orebodies. Recent underground stope definition drilling at the two locations enabled specific TMBs, stratigraphic units and even individual sedimentary beds to be matched between the two locations, despite the large separation between mines.The correlation between the two deposits has implications for future exploration drilling north of George Fisher. If a specific stratigraphic horizon can be determined within one hole, positioning of further drillholes can be more accurately planned. The significance of having stratigraphic matches between Hilton and George Fisher also has implications for correlations with other Isa Valley deposits. Convincing preliminary TM and stratigraphic correlations have already been made between George Fisher and the Isa Lead Mine 24 km to the south.

Jan 1, 2002

By M J. Andrews, P J. White, I Bogie

Active geothermal systems occur widely in Sumatra and in the Taupo Volcanic Zone (TVZ) ofNew Zealand. There are also many occurrences of epithermal gold mineralisation in Sumatra, some of which are economic. Minor sub-economic occurrences of gold have been reported in the TVZ but none have yet been mined. There are both similarities and differences in the nature of the active geothermal systems and mineral deposits in Sumatra and New Zealand, which can be systematically related to the tectonic setting. The thicker crust and consequent predominance of silicic volcanism in New Zealand leads to hydrothermal systems which are little eroded and with limited lateral outflows. The systems in Sumatra are of mixed character, with some of the characteristics of those in andesitic island arcs such as Java or the Philippines, e.g. a higher proportion of systems with identifiable acid magmatic volatiles, a greater potential for deep erosion and lateral outflows than in New Zealand; but modified by the more oblique component of subduction and thickened crust so that some are localised in volcano-tectonic depressions and consequently have high piezometric levels of primary hydrothermal fluid. The unusual occurrence of calcic zeolites in veins associated with gold mineralisation in Sumatra is thought to be indicative of æsatelliteÆ boiling zones along de-gassed hydrothermal outflows.

Jan 1, 1995

By Watsford R. M S, Hutton R

Following the delineation of significant extra ore reserves during 1990, the decision was made to expand production from 350,000 tonnes of run of mine ore per year to initially 600,000 tonnes increasing to 750,000 tonnes per year. The existing plant consists of a conventional three stage crushing plant followed by a heavy medium separation plant that produces a product prior to grinding. Grinding is conducted in three stages of ball mill in series. Alternatives examined for expanding production included: aò SAG mill - ball mill circuit replacing the secondary and tertiary stages of crushing, the heavy medium plant and the existing ball mills; and, upgrading of the existing circuit configuration.

Jan 1, 1991

The history of the discovery and development of the Kambalda nickel orebody. is reviewed and the decision to process the Kambalda concentrates by the Sherritt-Gordon process at Kwinana is discussed. The Kwinana Nickel Refinery is described and the problems encountered in the first year of operation are Outlined.

Jan 1, 1971

The difficulty in creating and obtaining a competitive edge in the mineral industry is rapidly increasing. The Kiruna Iron Ore Mine in the far north of Sweden is currently thriving on the world market through firm managerial strategy. LKAB believes in upgrading its raw material to produce a high quality iron ore product for sale to steelworks throughout the world. It is vital that this product is also of uniform quality and quantity to provide quality assurance to customers. The first link in meeting these product requirements starts in the underground workings. Mining methods and operations are of large-scale. Automation and continuous production streamline operations and reduce operating costs. These factors have built Kiruna Iron Ore Mine into the world's biggest, most modern, underground iron ore mine. To remain competitive on the world market, LKAB relies heavily on research and development. The mine is currently in a phase of upgrading its operations. A 25-tonne Toro electric loader is being tested to improve the rate of output of ore from the mine. Long hole drills are being improved to increase accuracy and efficiency. An electronic detonating system will improve detonator delay precision. Projects are underway to better understand ore flow mechanisms from a caving orebody. Benefits include improved ore recovery along with better rock quality control at the caving front. The continued updating of mining operations at Kiruna will enable LKAB to continue to maintain its competitive advantage on the world market in the production of high quality iron ore products.

Jan 1, 1997

By A I M Ritchie

The pyrite oxidation rate is a process central to both the performance of bio-oxidation heaps, used in the pre-treatment of some refractory gold ores, and to the levels of pollution in acid rock drainage (ARD) from pyritic waste rock dumps. A goal in bio-oxidation heaps is to achieve high oxidation rates in the heap as a whole. In comparison, one way to mitigate the environment impact of ARD, is to reduce the overall oxidation rate in the waste rock dump since pyrite oxidation is the primary pollutant generation process. In both bio-oxidation heaps and waste rock dumps the overall oxidation rate of the pyritic material (the intrinsic oxidation rate) at these sites. Much research has been conducted over the last 40 years or so on the oxidation rate of pyritic material with particular emphasis on the catalytic role played by bacteria. More recently mathematical models and field measurements have clarified the extent to which oxygen transport rates are rate limiting, what the dominant oxygen transport mechanisms are and the physical properties of the heaps which have most impact on these transport rates and on the overall oxidation rate. How the performance of bio-oxidation heaps can be optimised and how the pollution load in drainage from waste rock dumps depends on gas transport mechanisms is briefly reviewed. The sensitive of the overall oxidation rate in bio-oxidation heaps and waste rock dumps to details of the intrinsic oxidation rate is quantified.

Jan 1, 1994

By Reeves I. And Farquhar J, Pearce S

The irregular shape of the Rosebery orebody, coupled with the inconsistencies in grade over short strike lengths, has meant stoping blocks have had to be small to combat dilution and stability problems. In the past, each lens was divided into regular block sizes and developed up to five years before production commenced. There were two major drawbacks to this practice; firstly, existing development deteriorated over time therefore requiring rehabilitation prior to production. Secondly, the pre-determined blocks could not be easily changed to incorporate changes in mining technology or economic circumstances. Bearing these problems in mind, it was evident that any new lens development had to be designed to allow maximum flexibility. The lens being currently developed is J lens. It represents approximately 50 per cent of the current reserves tonnes, and 65 per cent of the zinc metal. Its importance to the mine's future cannot be over emphasised. At its core the lens is up to 25 m thick at grades of over 30 per cent zinc. The practice of dividing the orebody into levels and sublevels, with consequent crowns was no longer acceptable because of restrictions in stope design and potential loss of ore. To assist in the development planning of J lens, a geostatistical block model was applied in long section to graphically represent the lens. Areas of high zinc concentration, as well as zones of uneconomic material were identified by using the model. This has meant that the development could he targeted, enabling stope delineation to occur in the lens without significant ore loss. Because of limited development resources, and the need to bring J lens on-line in the near future, the development strategy has had to focus on 'just-in-time' principles, rather than accessing the whole lens from bottom, and progressing upwards. Tight development schedules have required individual stoping block to be developed on such factors as grade and available tonnes rather than as a vertical sequence.

Jan 1, 1993

In blasting large tonnages of ore or material, the economy of the operation 'depends mainly on the mine manager's judgment in placing the holes to the best possible advantage and in determining the most effective size of hole to suit the conditions and requirements.The placing of holes is often looked upon as a problem involving so many uncertain factors that the application of simple mathematics is impossible. The uncertain factors arise when dealing with strata of different character, in hardness toughness and resistance to shearing.A study of the practice at many mines where all types of strata from hard ore to relatively soft overburden, and even coal, is being mined, suggests that the problem is not as complex as generally believed. There is, without doubt, some uniformity in the amount of burden given to holes of equivalent dimensions, regardless of the material being mined. The reason is simple. With too great a burden hard rock will not break out and soft rock will "bull". The nature of the strata is taken care of by the strength, quantity and distribution of the explosive charge and, to some extent, the spacing of the holes.It is because burdens are uniform in all classes of strata met with in mining, that a formula can be used to design blast hole layouts.The formula introduced in this paper is empirical as it is based on prevailing practice. It has been tested and proved remarkably accurate against every example available to the writer. Many thousands of blast holes, at many different mines, are represented by the examples given in the attached tables; to give further examples would only mean, unnecessary repetition. At the Mount Morgan Mine...

Jan 1, 1952

The mineralisation consists principally of layered pyrite, phalerite and galena, situated conformably within a sequence of tuffaceous, bituminous shales and dolomitic sediments that include slump breccias. The sediments show little evidence of post sedimentary reconstitution. A volcanic-exhalative-sedimentary origin is postulated for the mineralisation. Attention is drawn to the similarity between the McArthur deposit and the lead-zinc-silver orebodies at Mount Isa. The primitive nature of the sulphides is reflected by their adverse metallurgical behaviour, and it seems that the best prospect for milling and flotation benefication may lie in the production of separate zinc and bulk concentrates

Jan 1, 1968

By Y Öztas, S McKinley, T Baker

The Kisladag Mine, Turkey, is a large porphyry gold deposit which is mined by open pit methods. In operation for over ten years, Kisladag provides an excellent example of how attention to a geologic feature, namely hydrothermal alteration, became a very effective predictive geological tool for planning and operation. The alteration domains were initially used as a geological tool to assist with establishment of resource model domains and to guide delineation drilling, but they were soon recognised to be correlative to geotechnical characteristics (affecting pit slope angles) and metallurgical performance (heap leach recoveries). Recent developments in spectral processing allow the systematic quantification of complex overlapping alteration phases and have greatly improved the ability to rapidly define internally consistent alteration domains for geotechnical and geometallurgical purposes.Alteration at Kisladag comprises a central core potassic (K-feldspar-biotite) zone, a tourmaline-white mica enveloping zone, an advanced argillic lithocap on the deposit’s eastern side and an overprinting pervasive argillic zone. These alteration zones and their distribution were based initially on strictly qualitative, visual mineralogical logging of diamond drill core. With the need for more accurate and consistent identification of the alteration mineral suites, particularly the phyllosilicate phases, logging was augmented by systematic measurement of spectral data using a Terraspec instrument.Recently the Kisladag spectral database (over 85 000 readings) was reprocessed by the newly developed methodology (aiSIRIS™) that allows relative quantification of the spectrally-responsive minerals. Visualising this transformed spectral mineralogy at various mineral concentration thresholds using implicit modelling software (Leapfrog®) led to the creation of consistent mineralogical and alteration domains that are used for the definition of geotechnical and geometallurgical parameters. An implicit modelling workflow enables these domains to be easily updated as new data is collected while maintaining geological integrity of the model.CITATION:McKinley, S, Baker, T and Öztas, Y, 2017. Alteration at Kisladag gold mine, Turkey – a progressive study in geology, geotechnics and geometallurgy, in Proceedings Tenth International Mining Geology Conference 2017, pp 51–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By N Mangadoddy, P Jampana, S Diddi

The study of air-core dynamics in hydrocyclone operation is essential for predicting separation efficiency in mineral processing. Electrical resistance tomography (ERT) allows non-invasive measurements of hydrocyclone internal flow dynamics. Existing regularisation methods such as Gauss-Newton and TV norms rely on optimisation techniques which have very high computational cost for very fine meshes. In contrast, the monotonicity method has much lower computational cost as it does not solve such minimisation problems. In this paper, results from the monotonicity method, Gauss-Newton (GN) (Tikhonov) and Total-Variation (TV) norm-based minimisation methods for estimating the air-core diameter in hydrocyclones are compared. We study these methods on the laboratory hydrocyclone experimental two-phase flow data. The results obtained are validated against High-speed video (HSV) imaging and Computational Fluid Dynamics (CFD) results. The results on different mesh sizes, in particular for very fine meshes with the number of cells ranging from 30 000 to above 100 000 are also investigated. The data used in this study is obtained from ITS Z8000 ERT system. This system does not measure the voltages on the current carrying electrodes. Since these voltage values are required for the monotonicity method, we implement an interpolation method to compute them. The results show that the monotonicity method provides a closer approximation of the interface between air and the water phases.

Aug 24, 2022

By Y Durkheim, P Saunier, L Ameglio

"In the last decade Afitex developed the Draintube™ geocomposite, which provides simultaneous drainage and waterproofing functions. This new type of drain tubes planar geocomposites (DTPG) differs from other geocomposites as the drainage core is composed of multiple corrugated and perforated pipes instead of biaxial or triaxial nets. It is furthermore associated with needle-punch stitched layers of non-woven geotextiles, which act either as capillary mediums or as filters.In this paper, the structure of the Draintube™ drainage composite is presented along with its key properties and the drainage mechanism associated with its particular structure.The relevance of this kind of structure is then reviewed based on past and current laboratory bench evaluations and field installations for mining applications such as the covering of acid rock drainage (ARD) tailings for the Central Manitoba Mine (Canada) site-rehabilitation; and as a pregnant solution collection layer in heap leach pads.Some of the demonstrated critical advantages of Draintube™ in the mining industry are as follows: reduction of the thickness, hence lower volume of granular drain layers improvement of fluid and gas collection and reduction of the hydraulic load reduction of secondary collector network mechanical protection of the sealing membrane fast and economical installation of interlifts stability under extreme conditions (compression, temperature, pH) increased stability of entire covering system and reinforcement of protection of dykes filtration of the covered material customised drainage positive connection of the geocomposite to collector pipes enable leaks detection (using a conductive textile layer) with an electrical test.CITATION:Saunier, P, Ameglio, L and Durkheim, Y, 2015. Tubular drainage and lining geocomposite for mine tailings and heap leach pads, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 297–304 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 27, 2015

By R W. Wilson, A R. Branch

For hot mines, the use of mechanical refrigeration machines has become an essential feature of ventilation and cooling systems. Over the last 30 years, considerable effort has been made in developing refrigeration strategies and equipment to provide cooling that is cost-effective, reliable and energy efficient. In addition to these general design requirements it is necessary to take into account project specific factors such as long term mine cooling needs, operating strategy and installation time. This paper examines a number of actual mine cooling installations which illustrate how these features have influenced the design and installations. For many mines, it is known how the cooling requirements will increase as the mine develops, based on the life of mine plan. The design of the cooling installation must cater for both short- and long-term needs. The initial installation (to meet short-term requirements) must form an integral part of the ultimate cooling installation and as additional equipment and refrigeration machines are installed, it is necessary to ensure that the system remains cost-effective, reliable and energy efficient at all stages. For many mines, refrigeration machines are installed on surface and either operated near-continuously, or for the summer months only. Different maintenance strategies and policies with regard to standby equipment are highlighted for three mine installations. In spite of developments in cooling strategy, the cost of providing refrigeration remains expensive and many mines delay the introduction of refrigeration, as long as possible. When it is finally accepted that refrigeration is absolutely necessary, it is frequently necessary to æfast trackÆ the installation. To minimise site erection time and meet installation deadlines, factory pre-assembly and standardised modular equipment are widely used.

Jan 1, 2005

Trucks are the primary means of bulk material transport in Open Pit hard rock mines worldwide. They are considered to be the most- flexible system available. The large number of trucks used in some mines provides flexibility. Spare units allow for the reduced availability of the single units. Trucks have however very poor energy efficiency. Only 40% of the consumed energy is for transport of the payload, the remaining energy is required to move the dead load of the trucks. With the increase in cost, pressure, mine operators are now looking for alternative methods to make their operation more economical. Energy conservation and increasing haulage distances and uphill haulage are major factors in many well established operations. New methods have already proven themselves as more economical alternatives. Belt conveyors are an alternative means of transport with much higher energy efficiency. They use up to 80% of the consumed energy for transportation of the payload. Energy costs for conveyors are 30% of the energy costs for trucks on level transport and as little as 15% for elevating payloads. Belt conveyors require much fear spare parts and wear components than trucks. A factor of one to two times applies for level transport and ten to twenty times for uphill transport.

Jan 1, 1986

The implementation, during recent years, of the concept of distributing chilled water to improve cooling at the working faces represents a very important innovation for the mining world. In a logical extension to that concept it has been recognized that distribution of the cooling water at high pressure would provide a potential source of energy for driving water powered hydraulic machinery such as rockdrills, water jets for moving rock, and support props, in the workings. With this in mind, the Research Organization of the Chamber of Mines of South Africa is pursuing the development of such a dual system that will provide cooling in a deep mine and, at the same time, drive hydraulic machinery. A comprehensive design of such a system has been completed and has shown the concept to be entirely feasible technically using technologies currently available. A pilot system is working in a mine shaft 2000 m deep giving a pressure of 20 MPa at the bottom of the shaft and distributing the cold water into the workings at a pressure of 17 MPa. The system shows considerable potential for improving existing mining methods and will open the way for the development of new mining methods for deep mining operations.

Jan 1, 1986