Search Documents

By Hermulheim W

In the Federal Republic of Germany hard coal is mined underground only. The coal mines reach down to 1 500 m deep, recently having an average depth of 900 m. The commonly used winning system is long- wall mining with face lengths up to 250 in. The gate roads, which separate the seam into single panels, have an average length of one kilometre with a cross- section up to 20 m2. These single entries are usually supported by yielding steel arches. The installation of steel arches can hardly be mechanized. The choice of heavier support, caused by increasing depth and roadway cross-section, results in high cost for labour and material in gate roads. Furthermore, the heavy steel arch is acci- dent-prone, not only during installation but also during transportation and ship- ment. Rock bolts combined with a suitable lagging offer a way of mechanizing support work in headings. The aim is to decrease cost and to increase mine safety and pro- ductivity. Over the last ten years, 50 km of gate roads have been reinforced by a combination of rock bolts and weld mesh. Nevertheless, there are still differing opinions on the feasibility of rock bolting in gate roads. In Germany a long tradition and experience with steel arch support exists, whereas the function of an anchorage is a closed book to miners, preventing this new technique from spreading more quickly. Advantages and shortcomings of both steel arch support and rock bolting are compared. The experience with rock bolting up to now is reported. Possible improve- monts arm discussed.

Jan 1, 1986

The Australian mining industry is at an interesting stage in its development. Of the large number of mining companies in Australia, some are still solely domestic in their focus. others have made their first tentative forays offshore, and others are global players of significance in the world industry. It is not long ago that the entire industry was almost exclusively domestic in its focus. Very few companies before the early 1980s had ventured offshore, and those that did so were considered quite risque. The initial moves were made mainly by large companies who could afford to lose the funds expended in getting started in a range of offshore locations.

Jan 1, 1995

The range of environments which control the level of ground support required vary greatly in terms of rock type, rock structure and the mining method used. At the operating mines visited during this review the level of ground support was such that incidence of rock-fall- related accidents were rare. It was also found that methods existed to support most of the conditions encountered. The main problem areas were weak rock, major geological structures, areas of heavy jointing, high development density and areas affected by high mining-induced stresses and blasting. With stope support the level of success was much lower than that achieved in development; the larger spans and more rapid changes in geometry of open stopes compared with cut and fill stoping (where cables were originally used) led to significant problems. Before a useable design method for cable support of stope walls and pillars can be obtained the precise failure mode of the walls and pillars, and the interaction of the support and the rock mass must be investigated.

Jan 1, 1982

The Golden Cross mine commenced production in December 1991. Both open pit and underground mines produce 1000 tonnes of ore per day. Mining techniques are discussed along with results and variations to proposed methods of extracting the ore.

Jan 1, 1992

This paper describes a proposal to reopen the Sylvia gold mine for underground exploration and development for an initial production of 10 000 tpa. A combination of trackless mining equipment and railtrack would be utilised for development with ore extraction being carried out by undercut and fill methods. The use of the smallest LHD units for mucking, and rail track for the main haulage together with airleg drilling will form the basis for development and stoping. The proposal has been subjected to an environmental impact assessment report to evaluate the impacts of the proposal on the natural and social environment in the area.

Jan 1, 1987

No paper was submitted for the proceedings, verbal presentation only (no material available).

Jan 1, 1998

During mapping in the Bijerkerno area (Fig. 1), well-preserved sedimentary structures were found at three separate localities. The structures are of four varieties, which are 1. small-scale cross-bedding (Fig. 2),2. convolute bedding (Fig. 3),3. minor scour and fill (Fig. 4), and4. flame structures.Ripple-marking is also doubtfully present.These structures are best preserved in what was...

Jan 1, 1971

This paper reviews rehabilitation, closure, and post-closure management of the Tui, Golden Cross, and Martha Mines, all of which are located in the Waikato Region of New Zealand. There was no requirement for rehabilitation of the Tui mine, which was abandoned in 1973. There was a requirement to rehabilitate the Golden Cross mine. Mining at that site ceased in 1997, and rehabilitation is now well advanced. When first approved, there were some requirements for rehabilitation of the Martha Mine, but when reconsented in 1998, those were extended, and in addition a requirement for post-closure management was included. As a result, a Trust, funded by the mining company, has been established to take long-term responsibility for the site following completion of closure. The different rehabilitation/closure requirements at each of these sites illustrates that we have learnt something from the experiences of the past.

Jan 1, 2003

THE object of this paper is to review certain features in connection with the mining of narrow lodes, say up to 20 ft. or so wide. The types of ore-body to which it is intended to refer are those which occur. chiefly as fissure or shear-Iodes-that is, those lodes which are to be found in belts of country which have been subjected to dynamic stresses, resulting in the formation of cracks and fissures, into some of which has been concentrated sufficient metal-bearing material to form ores. Very frequently one of the walls of such a lode is found to be a fault, or plane of differential movement.The first point which comes up for consideration is the shaft and its position. From the information afforded by the prospecting which has been done on a lode relative to the dip, nature of country, &c., the position of the main hauling shaft can be determined. For purposes of general utility the hangingwall is generally chosen, if a vertical shaft, though, on account of freedom from creeps, the foot-wall would be safer. Vertical shafts are preferable to underlie shafts in many ways; but wherethe lode maintains a flat dip the cost of cross-cutting at the various levels becomes very heavy'. This difficulty may to some extent be modified· by sinking a vertical shaft in the hanging-wall...

Jan 1, 1912

Over the past 12 years screening of materials has undergone a dramatic change in both the types and materials used in screen mats and the quality requirements of the finished product. With the main thrust now on quality and a cleaner product a different approach was needed in the operation of sizing screens. New screen mats with many different aperture configurations have been developed using rubber and plastics.to replace the traditional screen mat of woven wire or punched plate.

Jan 1, 1984

By Hagan T. N, Tucker A. J

The Cumnock Open Cut Mine (COCM) is located in the Hunter coalfield in New South Wales. Five coal seams are being mined, mostly by drilling and blasting, loaders and excavators, and trucks. The annual production of coal is 1.3 million tonnes. Overburden and interburdens consist mostly of siltstones and medium to thickly bedded sandstones. The strata dip to the south-east at approximately four degrees. There are no major faults in the rock mass.

Jan 1, 1995

This paper presents the findings from an experimental study of the effects of shock and gas penetration breakage mechanisms in rick blasting. A blasthole liner method, which realistically seperated these two basic sources of energy in blasting, was developed and utilized. The use of four different explosives with contrasting detonation behaviour produced a wide variation in the nature of explosive energy transfer to the rock. Through extensive field experiments it was found that, relative to low VOD dynamite, the high VOD emulsion imparted greater shock to the rock and therefore produced finer fragmentation and greater back damage. The comparatively lower heave energy of the emulsion caused less immediate blast results were obtained with watergel and ANFO explosives, which have detonation behaviour and energy partitioning charecteristics lying between emulsions and dynamite.

Jan 1, 1990

By A Struminski

The principles of occupational risk evaluation resulting from the improper ventilation of the underground mines were presented. It was shown that the risk level implies the appropriate planning and usage of prevention methods. That approach is fundamental in the ventilation, fire and climate safety management in the copper ore mines. The paper uses the adequately modified Risk Score method.

Jan 1, 2003

Sluice box operating practices in Papua New Guinea (PNG), and published work on sluice boxes are briefly reviewed. Some recent work on sediment entrainment mechanisms occurring in sluice boxes have also been described. In the light of this information, some drawbacks in the commonly adopted sluice box operating practices in PNG, and ways of overcoming them, are also highlighted.

Jan 1, 1991

By Glatthar J. W, Lauder D. W, Manlapig E. V, Mackinnon I. R

The Ok Tedi copper orebody consists of porphyry and skarn orebodies. The skarn orebodies, identified by different mineralogies, are the source of high intermittent fluorine levels in the mill concentrates. This paper discusses the results of t

Jan 1, 1998

By Veloso L, Alvarez O, David D

Cerro Colorado operations The Cerro Colorado Mine is located 150 km east of Iquique in the Atacama desert of northern Chile. The mine is wholly owned by Rio Algom Limited of Canada and produces copper metal using a bio leaching process. Tw

Jan 1, 1998

By Fardy J. J

Abundance data are presented for a comprehensive range of elements in oil shale samples from deposits located in Queensland. The techniques of instrumental neutron activation analysis and spark source mass spectrometry were used to obtain concentration data for up to 50 trace elements in each shale. These techniques were supplemented by other spectrometric methods to obtain data for major, minor and some trace elements. Sixty-four elements were determined quantitatively. This comprehensive characterisation of oil shale samples from the major deposits in Australia provides inorganic abundance data not previously available. It also provides important background information for processing studies and the associated environmental aspects of shale oil production and waste disposal.

Jan 1, 1986

By McKenzie C. K, Stewart R. S, Simpson J

Blast control in small scale underground mining leads to improved fragmentation control, improved control over overbreak and dilution, and the optimisation of drilling and charging operations. Greatly improved control can be achieved through blast monitoring, to confirm proper implementation of blast designs and blasthole charging. Further improvements can be achieved through simple modelling, enabling blastholes to be placed in the correct locations and charged with the correct weight and strength of explosive. Improved design can be shown to significantly reduce overbreak and dilution, and even ground support costs. In one mine in Quebec, open stopes of widths varying from 2.5 metres to four metres and dipping at 36¦ to 38¦ were designed to achieve zero dilution using open sloping blasting practices. The first stope designed in this manner was monitored in detail and achieved its objective.A method for contouring damage around blastholes is presented as a basis for selection of drilling patterns, with particular application to the control of overbreak and dilution. Contouring can be used to provide reliable estimates of either overbreak or damage (where rock is broken het reynainc in nlarr)

Jan 1, 1993

Mount Gibson Iron Limited (æMount Gibson IronÆ) has made the difficult transition from a privately owned company with an iron resource to a publicly listed company owning and operating a profitable iron ore mine in the mid-west of Western Australia. The development of the company is described with particular emphasis on the Tallering Peak operations, resources, associated infrastructure and logistical arrangements; the Mt Gibson hematite and magnetite resources and the proposals to develop the magnetite resource as part of an integrated project through to iron pellet production. The concept of tailoring the relatively small ship capacity of the outturn port of Geraldton to appropriately sized inturn ports in China to allow direct delivery of product is discussed. The companyÆs philosophy of building shareholder value by progressive development of its relatively modest resources (compared with the Pilbara) is discussed. In pursuit of long-term business success Mount Gibson Iron has formed symbiotic relationships with strong business partners whose aims and objectives mirror or complement those of Mount Gibson Iron.

Jan 1, 2005

By Ralph AM, Deakin JJ

A quantitative knowledge of underground mine ventilation requirements and conditions has become increasingly important, both to meet statutory requirements and to ensure high levels of safety and productivity within mines. The ACIRL Mine Ventilation System MINVENT was designed to provide a flexible means of analysing the behaviour of an underground mine ventilation system under a variety of conditions. It is not sufficient to rely solely on the analytical tools such as ventilation network analysis computer programs - these must be supported by the expertise necessary to conduct an accurate underground ventilation survey as well as experience of typical conditions to be expected in the evaluation of proposed extensions to a new or existing mine. When planning a new mine, the ventilation engineer can use the program to draw on a set of typical ventilation parameters, seam and proposed mining methods. These have been assembled as a result of numerous ventilation surveys conducted by ACIRL in New South Wales and Queensland.

Jan 1, 1983