Search Documents

In coal room and pillar, and pillar extraction panels, the sidewall conditions were investigated based on underground measurements and numerical simulations. Three-dimensional linear elastic models provided a useful and quick prediction of the amount of sidewall spalling. However, more complex constitutive models were required to simulate more accurately the extent of fracturing and its effect on the stress re-distribution. The input parameters of a Mohr-Coulomb model were determined by back-analysis of underground measurements, and the effect of the depth of the workings and the time dependent occcurrence of coal pillar fracturing were analyzed.

Jan 1, 1992

By K Lee, K Fernando, S Rayner

Copper-gold ores have been technically difficult and uneconomical to process due to high consumptions of cyanide. Many copper oxide and sulphide minerals react with cyanide to form copper cyanide complexes, partly contributing to the high level of weak-acid dissociable cyanide in the tailings which is normally experienced during the processing of copper-gold ores. The cost for detoxification, if required for treating these tailings, would further inhibit the development of these copper-gold resources unless the cyanide used for leaching was recovered. Several technologies have been proposed to process copper-gold ores, aiming to recover copper as a co-product and cyanide for recycling in conjunction with the leaching process. A critical review of these processes reveals that a pre-concentration stage (solvent extraction or resin ion exchange) is required. Cyanide is recovered by the conventional Acidification-Volatilisation-Regeneration technique in most cases. A critical evaluation is also provided on technical aspects related to the use of Vitrokele Technology and a newly developed Elutech process in processing copper-gold ores, in particular with its application at May Day Mine.

Jan 1, 2000

A number of suggestions have been made to improve the design of cells used for electro winning and electro refining of metals. Most of these designs have been aimed at increasing the current density used in order to improve cell capacity, although the purpose of some has been to produce electro deposited metals in a continuous manner. Improvements in the electrolyte flow pattern in conventional cells have resulted in an increase in the rate of mass transport of metal ions to the electrode surface; giving rise to lower concentrat- ion polarization and an improvement in the nature of the product obtained, Other cell designs are based on a moving electrode, usually a rotating disk, and these may include provision for removal of the product in a continuous manner, The maximum current density which can be used in an electro- lytic deposition process is determined by the limiting diffusion current, the physical nature of the, product, the purity of the product required and by the increase in power costs which result from the higher cell voltages, This paper examines the properties of an agitated bed of particles as an electrode system when used for a metal deposition Process,

Jan 1, 1969

A methodology for the fatigue life estimation of load haul dumpers, employed in underground platinum mines, has been developed and applied. This method entails the quantification of operating conditions by means of stress measurements. The measurements are then translated into a fatigue loading factor for a finite element model. The results of this analysis are then used to compare all the critical connections in the structure to detail categories in relevant fatigue codes, and predict a life in operating hours for the vehicle structure. The method was applied on a specific model and the results of this analysis were compared to actual failure occurrences with reasonable accuracy. It is intended that the methodology be embedded into performance specifications and purchasing contracts and that technology transfer to OEMs be achieved. Based on the experience of this project and other similar exercises it is estimated that structural life expectancies may be increased across a typical fleet of trackless mining vehicles (LHDs, drill rigs, utility vehicles, dump trucks) by at least 20 per cent.

Jan 1, 2005

Reason Analysis of Impurity Containing and Technology Discussion of Quality Improvement for Low-Quality Iron Concentrate

Sep 13, 2010

Investigation on Comprehensive Utilisation of Nickel Slag from JNMC

Sep 13, 2010

Combined Flow Sheet for Treatment and Recycling of Municipal Solid Waste (MSW) with Complex Morphological Composition

Sep 13, 2010

Attempts to rationalise the geological environment of nickel sulphide deposits associated with Archaean ultrabasic rocks has produced much speculation as to the origin of the sulphides and the relative importance of geochemical, mineralogical, textural and structural characteristics of the host rocks. From an economic viewpoint the object of such work is to establish geological criteria which can be used as an exploration guide. Exploration procedure for nickel sulphide mineralisation of the 'Kambalda type' (Hudson, 1972), which occurs at or near the basal contact of Archaean ultramafic flow units and lenses consisted of geological mapping, surface prospecting with soil sampling and rock geochemistry.

Jan 1, 1987

Longhole stope overbreak has always been a source of unwanted cost within the underground mining industry, and efforts to control it using various rock reinforcement systems have long been a rock engineering challenge. At the Pasminco Mining Broken Hill Operations trials have been carried out using an innovative cable bolt reinforcement system known as Rib-Roc. The system, based loosely on the Swedish Rib-in-Roc concept, utilises zones or ribs of heavily reinforced rock in the troublesome hangingwall and back areas of longhole stoping. The trials were carried out under a strict qualitative and quantitative scientific stope measurement program utilising rock mechanics instrumentation. Not only did the trial demonstrate the success of the system but data obtained was useful in implementing the system virtually as standard practice throughout the operation.

Jan 1, 1995

By Luck D

Current methods of mucking out small development tunnels are a major limitation to improved efficiency and high rates of advance. This is particularly true in the deep metalliferous mines of South Africa, where the harsh environment, remoteness of operations and the hard abrasive rock conditions mitigate against the use of the tunnel borer type of equipment. The Loader Distributor Train was designed to overcome the special problems of hard rock tunnelling. It combines advanced innovative technology with proven simple methods of operation and maintenance. The system aims at taking advantage of new, efficient and cost effective power sources in South African mines based on replacing compressed air with electro hydraulics and the new concept of hydropower. It also introduces electronics and computer technology, for both automatic control and fault finding, into the production environment. The system is designed to permit sophisticated equipment to be operated and maintained by a semi skilled labour force. Although still undergoing trials it is believed that the Loader Distributor Train will prove highly effective, and that the new concepts offer considerable potential in areas other than flat tunnels, in particular the cleaning of inclined shafts.

Jan 1, 1986

Deposits of the Reefton Goldfield, West Coast, New Zealand, are hosted on N-NE striking, upright folds of the Greenland Group. High-grade quartz lodes are hosted on axial planar shears, typically have short strike lengths, and form shoots that pitch steeply on the hosting shears. Deposits within the field area of a detailed structural study share these characteristics. Field mapping and microstructural analysis have demonstrated that the Greenland Group was affected by a multideformational sequence. Gold mineralisation is hosted on shears axial planar to the F2 folds, but occurred during a subsequent deformation event (D4). Deformation during D4 resulted from N-NE directed shortening, near parallel to the trend of the F2 folds. This event produced F4 kink folds that were accommodated by layer parallel slip on S2 parallel shears, gold mineralisation during D4 being confined to the dilational hinges of F4 kink folds. The semi-brittle nature of D4 allowed the formation of stockwork veining and disseminated mineralisation within the F4 hinge zones. Most deposits within the goldfield are similar to those within the field area, and are interpreted to have been mineralised during D4. The two largest known deposits within the goldfield, however, are distinct. The Blackwater Deposit, striking parallel to the hosting folds, has a combined strike length of 1 km. The Globe-Progress Deposit is hosted on an E-W striking discordant shear in which a brittle zone of disseminated mineralisation encompasses high-grade quartz lodes. The characteristics that distiguish the Globe and Blackwater deposits may be due to formation before and after D4 respectively. Detailed field mapping in the vicinity of known deposits throughout the goldfield will further refine the relationships between the F2 folds, later deformations and the localisation of ore deposits. Additional mapping may also help constrain the position, orientation and extent of additional orebodies.

Jan 1, 2001

By Paley N, Cameron A, Townson P

Although blasthole deviation is a problem which can seriously affect blasting operations, there is little practical emphasis on controlling this deviation and no practical emphasis on understanding its practical behaviour. The most common way of dealing with it involves tight control over drill set up and surveying hole paths. The surveying might involve simple collar location and inclination measurement to estimate the hole's actual path. At best, some operations routinely survey hole paths after all holes in a stope have been drilled. In addition, although there is an expectation that holes will deviate, there is no planning for this behaviour in order to reduce its impact on the blast. Design decisions are invariably made with the assumption that holes are straight. If and when surveys reveal problems it is possible only to adjust charging and initiation to 'work around them'. In extreme cases the drill might be recalled to fill in gaps. The lack of planning and the lack of understanding are doubtlessly linked.A model is presented that will predict the expected path of a drill hole. By knowing how a selected few holes deviated it is possible to make a good estimate of the deviation of other holes in the same rock mass. After minimal calibration the model can be used to increase the amount of information for a given amount of surveying or the amount of surveying can be reduced while maintaining the same level of knowledge of blasthole deviation. Equally important is the ability to plan for the deviation in future drilling through altering the initial collar angles or drilling from different locations. It is the authors' hope that planning for hole deviation becomes as much a part of the design process as planning for detonator delay scatter and explosive performance variation.

Jan 1, 1992

By Dickerson A. W

The most important mining problem facing many of the established surface coal mines in the Bowen Basin area of Queensland is the rising cost of overburden stripping associated with increasing depths to coal. The Dragline-Hopper-Truck Project is one of a number of responses to this problem, and involves the design and construction of an experimental hopper followed by field evaluation of a dragline-hopper-truck mining system.Such systems, if proven feasible, could be used for a range of applications, eg prestripping, extension of depths for single pass dragline operations and solution of geotechnical problems.

Jan 1, 1992

Although a small quantity of lc,;v viscosity index ' (L.V.I.) oils are presently manufactured in. Australia, lubricating oil refining methods are assuming gxeater significance since in 1964 Australia will be locally refining the bulk of its requirements and some companies may be exporting a surplus. New plants are ' planned to refine mainly high and medium viscosity index oils from imported crudes and the paper describes typical techniques used òto: produce. thes& oils. .

Jan 1, 1962

Pipe Jacking has been a recognised method of tunnelling in the U.K. since the early 1950's, although I understand that pipes were pushed blind by the soldiers in the first World War from trenches on the Allied side to, or adjacent to, trenches on the German side, thus allowing explosives to be used with a certain element of surprise! 'However, on its more conventional to the U.K. in the 1950's, Pipe Jacking made considerable inroads into the tunnelling market place as an alternative to timber supported headings. This success was, unfortunately, fairly short lived because, owing to its simple method of operation, contractors paid insufficient detail to the engineering (or surveying) aspects and as such the system soon had a bad reputation for unreliability and lack of accuracy. Due to these failings, the market was not exploited and, therefore, there was a lack of investment by contractors, pipe manufacturers and also by any client, or research organisation, which is client associated. The effect of this meant that the system stagnated for a number of years and was used generally only for short crossing work (i.e. railways, canals and motorways), and then only in good homogeneous ground. Albeit, a limited number of full scale sewage disposal contracts were carried out, but with the lack of knowledge and experience of the clients, contractors and suppliers, (particularly the pipe suppliers), no reasonable success, either physical or financial, was achieved on any such contract.

Jan 1, 1987

The Century zinc-lead orebody was discovered in 1990 and contains sufficient reserves to sustain open cut mining at 5 Mtpa of ore for approximately 20 years. It is proposed to pipe mineral concentrate in slurry form 300 km from the mine to the port of Karumba on the Gulf of Carpentaria. The concentrate will be dewatered at Karumba before being transported off-shore to deeper water in a self-unloading shuttle vessel for transfer to export bulk carriers. The four main environmental issues that attracted attention during the impact assessment phase of the project were: the selection of Karumba as the export port, the use of a pipeline to transport concentrate, the risk of concentrate spillage in the marine environment, and aquifer drawdown in the vicinity of the mine. This paper discusses these issues with emphasis on the context of the relationship between the Pasminco Century Project and Gulf communities. Environmental safeguards are discussed, including those that arose out of the negotiations regarding Aboriginal native title.

Jan 1, 1998

By McMahon DW, Schapper MA

Hard rock underground mining has been wedded to the drill-blast method of breaking rock. Current practice and technology have focused on greater efficiencies in the blasting and handling of ore, on the basis that thelower costs that come with larger scale operations compensate for the waste dilution associated with the bulk methods. However, it is suggested that new technology is available or is on the horizon that could completely change the shape of hard rock mining in the 21st century. Hard-rock continuous-mining machines, possibly assisted by high pressure water jets, coupled with automated sorting and materials handling systems, could re-orient the miner's focus to winning metal rather than mining tonnes of ore. More continuous mining processes could accelerate the penetration by high technology in the hard rock underground mine, with the potential of greater manpower productivities and lower costs per tonne of metal produced. This new technology will be important in maintaining a competitive supply of metals, given the falling headgrades of the orebodies remaining for development and the increasing market threat from manufactured substitutes.

Jan 1, 1985

By Gutsche O, Kapur PC

Experimental data on the production of fines as a function of specific grinding energy consumption show that in general the energy utilisation in a choke fed high-pressure roll mill is higher than in a ball mill, but lower than in the single-particle mode of comminution under slow compressive loading. There is some evidence to suggest that the presence of water in feeds improves the energy efficiency of pressurised roll milling somewhat. Within a wide range of energy input, the size distributions of the ground product are self-similar, the logarithmic median size decreases linearly with the amount of fines produced and the inverse of the median size increases linearly with the energy spent. The production of fines as a function of energy expended follows essentially the same pattern as the one frequently encountered in media mills. The kinetics of grinding in the high-pressure roll mill can be simulated satisfactorily by modifying the standard particle population balance equation in order to account for energy dissipation in the tightly compressed bed. Common characteristics and important differences in grinding by the media mill and the high-pressure roll mill are highlighted.

Jan 1, 1993

The Use of Automated Mineralogy to Interpret the Batch Flotation Performance of Merensky Reef Ore

Sep 13, 2010

By S B. Stewart, C J. Restarick

Over a four-hour period of steady plant operation samples were taken at regular intervals frum points within the grinding and flotation circuits. Size fractions of each composite sample were analysed for lead and zinc values and a comparison made of the behaviour of the lead, zinc and gangue minerals, size by size throughout the whole circuit. Analysis of the breakage behaviour using dynamic mathematical models gave the rates of breakage of each size fraction of each main component. Simulated grinding experiments shaved that the main grinding circuit had some reserve capacity. In the lead flotation circuit all lead values between 150 mesh (Tyler) and 5 ¦m had excellent flotation characteristics, and a major proportion had a high rate of flotation which was practically the same for all sizes. Increase in overall lead recovery would require improvement of the flotation behaviour of ultra-fine lead minerals. These were slav floating and were responsible for approximately half the lead losses in the final zinc concentrate and one thiro of the lead losses in the final tails. All sizes of zinc values between 150 mesh and 7 ¦m floated well and the performance of the zinc flotation circuit was mainly limited by the relatively poor flotation of the very fine zinc values. Approximately 60 per cent of the zinc lost to the final tails lay within the -7 ¦m fraction. The overall flotation conditions were conducive to very good selective flotation of the major proportion of the values and limitations in metallurgical performance were mainly due to the properties of the ultra-fines.

Jan 1, 1971