Search Documents

Tried, Tested and Proven - 300 m3 Flotation Cells in Operation

Sep 13, 2010

By Oda Y, Hashiuchi M

In the smelting section, flexible fuels such as coal or coke are used in place of heavy fuel oil in order to utilize energy sources more efficiently. Heat recovered from the off gas of the furnace has been converted by the waste heat boiler into steam, which is used for self power generation and for heating or maintaining various temperatures. The amount of the recovered steam in the smelter is currently increasing due to maximum utilization of powdered cokes. The heat source required to maintain the temperature of the electrolyte in the tank house is electric power and steam. However until recent year this steam was provided by its own heavy oil combustion type boiler in the tank house since the amount of steam consumed in heating the electrolyte is large. Though experimental work over the last few years has shown the advantages of reducing steam in the tank house by fully covering the cell, the implementation of the full cover can lead to other operating problems. However various improvements, mainly the covering of the cell with a simple device, have led to greatly reduced steam consumption. As a result, steam for the tank house is now provided by the waste heat boiler only bringing more efficient energy usage.

Jan 1, 1987

Recycling of Process Water in Sulfides Processing and Flotation Selectivity

Sep 13, 2010

By G B. Siddall

The paper examines the current state of equipment and circuit design, with reference to Australian practice. Following a review of the changes in milling applications over the last 15 years, developments in mill design are examined. Current issues include trunnion versus shell support; drive type and economic analysis for comparison of the various systems; the efficiency of the mill discharge system for slurry and pebble removal, and lining configuration. Peripheral problem areas such as pebble crushing and classification are briefly examined. Circuit design issues are reviewed. The decision to modify the traditional primary crushed feed is examined with reference to recent and proposed installations. A retrospective look at fully autogenous installations and their successes is presented, and current views on increasing throughput are assessed. Finally, future developments are anticipated in mill design and control, and competing processes are identified.

Jan 1, 2002

By Revy T

A testwork program aimed to improve the assaying of underground face samples established that for an Accelerated Cyanidation Extraction using the LeachWELLTM 60X catalyst, followed by an Aqua Regia finish (to quantify non-cyanide-extractable gold): ò Assay results (including the aqua regia finish) from a full set of samples from one underground face can be returned within four hours. ò The reagent dose to make the method simple and 'bullet-proof' is 8 gm LeachWELLTM 60X and 20 gm NaCN per 200 gm sample (30 per cent solids). Pulverising is to 90 per cent passing 75 micron (compared to the standard of 90 per cent passing 150 micron), and cyanidation is completed within one hour - however both might be further optimised. ò The LeachWELLTM/Aqua Regia results demonstrate that Fire Assays suffer from a significant nugget effect which makes the Fire Assay data relatively unreliable. ò Original costs, specific to Bannockburn (viz including an Aqua Regia finish), handling approximately 20 000 to 25 000 per annum is estimated to be $5.40, ie about one-third less than fire assaying. Optimising is further reducing these costs. It is estimated that the LeachWELLT"'/Aqua Regia assay procedure has reduced the probable error limits of any given assay of this ore from the range 0.74x to 1.36x for Fire Assay, to an appreciably smaller range of 0.90x to 1.11x. Thus for a cut-off grade of 1.60 g Au/t, samples with Fire Assays ranging up to 2.18 g Au/t have 25 per cent chance of being below cut-off, while samples with Fire Assays as low as 1.18 g Au/t have an equal chance of actually exceeding cut-off grade. This 1 g Au/t range in uncertainty is generally unacceptable for many practicalgrade/tonnage relationships. By contrast, using LeachWELLTM + Aqua Regia assays, the estimated corresponding limits are 1.44 g Au/t and 1.78 g Auk respectively - a far more tolerable 0.34 g Au/t range of uncertainty. Subsequent data has demonstrated that sufficient accuracy for grade control is achieved by Accelerated Cyanidation alone, further halving the cost of assays.

Jan 1, 1994

The Kalkadoon Granite is regarded as composite in character with at least two different phases. The older phase is considered older than the sediments of the Western Geosyncline, and the younger phase is considered younger than the sediments of the Western Geosyncline.Consequently, the older phase could be a time equivalent of the Ewen Granite, whereas the younger phase could not. An age of 1760 million years seems plausible for the older phase, and an age of 1540 millionyears seems appropriate for the younger phase.

Jan 1, 1967

By See J. B

The zinc-nickel alloy process, TECHNIGALVA, was developed for the control of the thicknesses of zinc -coatings on reactive silicon-killed steels. These are steels containing between 0.04 and 0.15 per cent silicon which have become more common in recent years as more steel is produced by continuous casting. The introduction to this paper will review the current status of this process in Europe, North America and Australasia. It is well known that the presence of silicon at certain levels in steel can cause sufficient growth of intermetallic phases during galvanising to form a grey coating of excessive thickness. This type of coating is undesirable because it is brittle and has poor adhesion to the steel base. Since the early-1980s a widely accepted practice for suppressing the reactivity of steels containing silicon during general galvanising has been the addition of approximately 0.1 mass per cent nickel to the galvanising bath ie the TECHNIGALVA process. The paper will also discuss metallurgical aspects of the use of nickel in galvanising such as the mechanisms by which nickel suppresses reactivity, the structure and composition of the ternary Zn-Fe-Ni drosses formed when using nickel and the use of nickel in the galvanising bath at a level of about 500 ppm to give thinner, smoother and brighter coatings on steel.

Jan 1, 1993

By B Lavin, R Sanford

This paper examines the application of Lean Manufacturing in a mining environment, based on experience within the Rio Tinto entities: Rio Tinto Aluminium, Northparkes Mines and Hunter Valley Operations. The three applications have tested the flexibility of the Lean methodology. Within Rio Tinto, Rio Tinto Aluminium was the first group to introduce Lean. The rollout began in late 2004. It was introduced firstly at Boyne Smelters, Gladstone, as a model site with the initial application in the Carbon Bake Furnace area. It was later extended to other sites including the Weipa Bauxite Mine. LeanÆs successful application within Rio Tinto Aluminium was in part responsible for its recent adoption by other Australian-based Rio Tinto business units including Northparkes Mines, a copper mining operation in Central New South Wales, and Hunter Valley Operations, a group of four coal mines in the Hunter Valley region of New South Wales. Lean is also being adopted by Rio Tinto Iron Ore. Rio Tinto Aluminium introduced Lean Manufacturing to complement an existing Six Sigma business improvement program and to achieve continuous improvement activities at a workplace level. Lean provides a similar level of rigour and discipline to Six Sigma but its application is everyday and for everyone, everywhere in the workplace. It is a valuable management tool. In a short time, Lean has achieved good and sometimes spectacular results improving productivity and efficiency at all sites, including our mining site. Within Rio Tinto Aluminium, it has also had beneficial impacts on our ability to develop and retain employees.

Jan 1, 2006

By Brinkmann J. R

The relative effects of the two basic mechanisms contributing to rock breakage during blasting, shock and gas penetration, are neither well understood nor well characterized, and need further clarification. Blasthole liner (BHL) tests separate the two effects, and by enabling direct measurement of borehole expansion give insight into the shock/gas energy partitioning in rock confinement. The hydrodynamic code DYNA2D is used to simulate the shock effect of the detonation of emulsion in a stainless steel lined hole, and the predicted expansion is compared with experiment. Workers in the past have neglected near-blasthole phenomena and have calibrated models based on stress measurements remote from the blasthole. Extrapolation back to the blasthole has inherent limitations, and indeed, one of the deficiencies of these models is that they have not been able to predict correct borehole expansions, as observed in BHL experiments. DYNA2D has been enhanced by the ICI group with a detonation model which resolves the explosive reaction zone. As a preliminary step towards the ultimate goal of devising a practical damage model, simulations are used to predict the maximum expansion that would take place if the rock were to remain undamaged. Various material parameters are investigated and it is shown that calculated liner expansions are appreciably lower than measured values for high rock yield strengths, while greater than values for low yield strengths.

Jan 1, 1990

By Lee H. G, Li H, Hayes P

Slag from the smelting of lead can contain up to 20 per cent zinc as an oxide. An understanding of the lead smelting process and of the subsequent fuming process for the recovery of zinc is enhanced by a knowledge of the activity coefficient behaviour of zinc oxide in smelting slags. The literature presents a wide range of contradictory values. This paper critically reviews the published data and outlines new measurements being made by the authors. A consistent set of zinc oxide activity coefficient data is presented for liquid slags within the ZnO-'FeO'-CaO-A1203-SiO2 system, through a combination of present and previous measurements.

Jan 1, 1993

By T R. Gibbons, I Grayand

Geotechnically massive strata may lead to a host of problems during longwall mining. These include windblast on initial goaf fall, sudden loadings on powered supports, periodic weightings, fractures that may propagate to surface, and extreme subsidence problems. It is essential to identify these problems prior to mining and to appropriately deal with them. The problem is essentially that the rock mass does not breakup evenly and when it does so it tends to produce large blocks which may suddenly move. The rock types that produce these problems tend to be massive sandstones, massive siltstones and sometimes igneous sills. The fundamental problem with these is that they do not breakup readily. This is because the ratio of stress they are subject to compared to their strength is low. Thus, the shallower mines with lower stresses are more subject to this problem than deep highly stressed ones with similar strength rock.

Nov 29, 2022

The use of econometric models to assess the effects of a Government's policy on an industry is gaining momentum. This is particularly so for the Mineral Industry and it is important that mineral industry management understands the techniques involved in developing econometric models. Models are usually constructed outside the industry by either government departments or their consultants and used by the policy makers to investigate artificially the implementation and ramifications of new policies. This paper discusses the application of econometric models in Governmental policy determination, highlights the use of various models in Australia and gives an overview of the techniques involved using Australian examples.

Jan 1, 1982

By Robbilliard K. R, Floyd J. M

The problems facing the metallurgical industry from the viewpoint of the range of unacceptable residues, flue dusts and slags currently produced from the electrolytic zinc process, electric arc furnace scrap treatment, and blast furnace operation in lead smelting and the Imperial Smelting Process (ISP) are addressed. The application of the Ausmelt technology is discussed and analysed for the pyrometallurgical treatment of zinc plant residues, steel plant flue dusts and lead blast furnace and ISP slags, as well as the more complex issue of smelter modernisation to avoid production of zinc plant residues in the future. Processes developed from pilot work are described and indications of the economics of treatment of electrolytic zinc plant neutral residue and jarosite are given.

Jan 1, 1993

By Morley I. W

In the year 1926, Edie Creek, in the Morobe District of the Mandated Territory of New Guinea, saw the greatest gold rush of recent years. Situated 35 miles inland from the coast, and at an altitude of over 6000 feet, Edie Creek presented to the original prospectors a wet, jungle-clad uninhabited, and inhospitable region. There were no roads; and the only means of approach from the equally inhospitable coast was by an eight to ten days' tramp through coastal swamps and gorge-scarred mountains. All food supplies and equipment had to be carried on the backs of "kanakas," and in many cases through country occupied by hostile natives.Since the first discovery of payable gold at Edie Creek, mining on the Morobe Goldfield has shown remarkable progress, and in spite of the tremendous natural difficulties, the field today ranks as one of the most important in Australasia.Aeroplanes, more than any other factor, have been responsible for this rapid development. They provide the only means of transport from the coast, and at present serve the needs of over 600 Europeans and 3000 indentured native labourers engaged in the industry.

Jan 1, 1933

By Wernick B. J

Recently, the Environmental Engineering Laboratory of the Chamber of Mines of South Africa Research Organization has made signifi- cant progress in the development of more accurate algorithms for assessing heat flow in gold mines. These algorithms have been incor- porated into an overall computer program, ENVIRON, which enables the complete thermo- dynamic analyses of mine ventilation and cool- ing systems to be carried out. Recently, efforts have concentrated on the development of an expert computer system which will guide engineers in the process of selecting the most appropriate environmental control strategy.

Jan 1, 1988

By Eupene GS

The Early Proterozioc Pine Creek Geosyncline hosts a large number of gold showings. Mineralisation types include stratiform, synsedimentary deposits within iron formation and carbonaceous mudstone; disseminations in granophyric intrusives; and quartz vein related concentrations in the form of shear fillings, saddle reefs and stockworks. Stratiform gold deposits preferentially formed near penecontemporareous faults during periods of basin instability. Intrusive basic magmas later assimilated some stratiform mineralisation and subsequently redeposited it within differentiated phases. Gold was again remobilized during regional deformation and metamorphism. Stratiform mineralisation was upgraded insitu in high strain zones and gold was mobilized into metamorphic fluids. Fluid induced fracturing during prograde metamorphism and later uplift caused the deposition of extensive gold rich vein systems. The genetic relationship between gold deposit types is reflected in the clustering of showings along regional anticlines, and provides a powerful exploration tool. The large volume of 'exhalative'òmaterial in the Geosyncline with elevated gold content suggests significant economic stratiform mineralisation may be present, and probably provides a source for later disseminated and vein deposits.

Jan 1, 1984

The diverse nature of inadvertent mine fires does not lend them to general treatment. But evolving from the unfortunate fires over past years is a simple principle in dealing with all fires to bring combustion under control. Control, in brief, means that the products of combustion, themselves possibly still with fuel values, are not revitalised by addition of fresh air. There are problems with fire- fighting, especially with water, as this may lead to production of CO and H2. Panel ventilation upstream of the fire must be controlled to direct all air over the fire. Some advantages in fire fighting are found by the use of "sails". Early diagnosis of fires and early treatment are essential for safety of personnel and safeguarding and recovery of property. Preparedness extends to up to date documentation, but first hand knowledge also is invaluable to the diverse personnel gathered to fight a fire, and in the decision making Involved.

Jan 1, 1981

Draglines have been a significant part of world open cut mining since the early part of the 20th century particularly for the removal of overburden in the strip mining of coal. Since the mid-1960s draglines have played a major part in the large strip mining coal developments of Queensland and New South Wales.There are now over 60 large draglines operating in Australia ranging in size from 23 to 103 cubic metres bucket capacity, with digging depths to 60 metres, dumping heights to 50 metres and dumping radii to 100 metres. The application of these draglines has progressed through the uncovering of coal in shallow, single seam operations to deep multi-seam operations requiring a greater dependence on pre-stripping activities ahead of the dragline to remove overburden not able to be efficiently handled by the dragline.

Jan 1, 1992

By M Kizil

Mining Engineering Degree programs have traditionally had a practical emphasis and have been highly vocational in nature. However, over the years, there has been an increasing attention to the more scientific aspects of the discipline. More recently, the professional institutions, the industry and the community at large have placed increasing emphasis on the broader aspects of the professions: management, finance, humanity, environment and social issues. Notwithstanding this, there has been a continuing emphasis on the practicalities, and most Mining Engineering programs are still strongly vocational in nature. But employers of new graduates complain about the graduatesÆ lack of practicality and readiness for employment æat the sharp endÆ on the mine site.This paper briefly describes some of the more recent developments in the Mining Engineering Degree program at the University of Queensland that attempt to address the problem. Particular attention is paid to alternative learning programs, including applications of virtual reality, practical experience at the University Experimental Mine (UQEM), and the Undergraduate Site Learning Program (USLP).

Jan 1, 2002

By T A. Helms, P Gottlieb, S E, R Bateman

In response to the ever-increasing challenges facing the modern gold mining industry and the need for improved gold recoveries within all processing streams, CSIRO has upgraded its latest automated mineralogical analysis system, QemSCAN (formerly QEM*SEM), with special purpose hardware that speeds up the location and measurement of precious metal-bearing phases. By rapidly scanning the surface of polished blocks, and accepting only fields that contain the minerals of interest, QemSCAN is able to find, map, and quantify target minerals in extreme detail. Phase identification and quantification is achieved by placing a grid of points over the target particle and collecting X-ray information at each analysis point. The resulting mineral maps provide the metallurgist with a complete textural description of all gold-bearing phases within the product measured, together with quantification of the gold phases in terms of their modal abundance, particle size, mineral associations, relative contributions to gold deportment and liberation characteristics. Examples are presented which illustrate how QemSCAN is able to find and quantify gold-bearing phases within low-grade ores from the Super Pit, Kalgoorlie. This work is the result of a collaborative project between Kalgoorlie Consolidated Gold Mines (KCGM), CSIRO Minerals, and the University of Queensland, and is on-going.

Jan 1, 2000