Search Documents

By B Upton, J Mitchell

The use of hydro scaling and in-cycle shotcrete to replace conventional jumbo scaling, mesh and bolting as the primary method of ground control for run of mine development has been investigated through extensive trials at the Waroonga mine, Agnew Gold Mining Company.These trials have progressed from investigating the productivity aspects of the method through to a three month mine-wide trial, which may yet lead to the adoption of this potentially best practice ground control technique at Agnew.Ov erseas trials and research have shown that hydro scaling results in a significant improvement in the shotcrete-rock bond strength. Good adhesive bond strength ensures that the shear strength of the shotcrete layer rather than itÆs flexural or tensile strength is fully mobilised as rock mass reinforcement.This maximises shotcretes ground reinforcement capability and it is suggested that a bolt-less fibrecrete support design is feasible using the hydro scaling technique.

Jan 1, 2005

A recently developed technique for use in collieries is described in which samples of gas of relatively high vitiation value are obtained from points deep within a developing goaf by means of pipes. This technique prevents dilution of small quantities of carbon monoxide by large quantities of fresh ventilation air and eliminates interference from shotfiring gases. By using the technique it should be possible to assign a characteristic ratio of carbon monoxide to oxygen consumed to any district and to predict the onset of heatings.INTRODUCTIONGas analysis has played a vital role in detecting heatings in collieries all over the world. By analysing return air from a district and by calculating the percentage ratio of volume of carbon monoxide found to oxygen consumed (known simply as the "carbon monoxide ratio") it has been found possible, in many cases, to assign a characteristic ratio to a district under consideration. This characteristic ratio serves as an index of the spontan~ous combustion tendency of a goaf area. Any definite and consistent increase in the ratioabove the normal figure· indicates that a heating is developing and hence adequate preparations may be made to deal with the trouble.This ratio technique was developed by Graham (1920-21) who found (Table 1) that the temperature of oxidizing coal was directly related to the ratio obtained from analyses of the effluent gas.Until recently, most attempts to employ a similar technique in collieries working the Greta Seam (N.S.W.) were not successful. From experience gained over the past few...

Jan 1, 1961

By J D. Pease, J M. I Tuppurainen, P D. Munro

This paper examines how legislation and regulation can be external drivers of technical change in mineral processing and extractive metallurgy and how the industry can respond. Two examples are considered; the production of copper metal from concentrates and the cyanide process for gold production.The Clean Air Act (1970) in the USA initiated a wave of attempted innovations in the extractive metallurgy of processing copper sulfide concentrates to meet forthcoming standards on sulfur dioxide emissions. Interestingly, a satisfactory technical solution existed (flash smelting and gas capture) but had not been widely adopted.Nearly fifty years later the primary copper industry finds itself with new challenges. One major challenge is how to deal with the increasing level of arsenic in copper concentrates. Most countries impose an upper limit on arsenic in imported concentrate; typically, 0.5% As or less. Higher arsenic concentrates can be blended with cleaner ones to meet the limit, but this tactic cannot be used indefinitely as the average arsenic level of global concentrates rises inexorably. Further, smelters (often in urban locations) cannot be expected to deal with both ever-increasing arsenic in the feed and stricter restrictions on emissions and disposal. A rising “inventory” of primary copper deposits are already constrained from development by high arsenic concentrate. These deposits will need to be developed if future copper demand is to be met. An economic and technical solution to arsenic is needed. The gold industry may also face challenges in the use of cyanide, by far the dominant lixiviant used in gold and silver production. Public perception has driven restrictions on the use or transport of cyanide in some jurisdictions. History suggests that such pressure is only likely to increase. While there are several alternative lixiviants, none can yet match the utility and economics of cyanide.Such important issues will not be resolved by incremental change or new equipment items. They require development of new process technology - a tectonic event rather than an incremental change. It requires sustained effort (and expenditure) over decades and is very unlikely to result from “business as usual” for producers, suppliers or academics. Past major process developments were driven by a dire need for economic survival or by legislative change. What will drive the future changes?CITATION:Munro, P D, Pease, J D and Tuppurainen, J M I, 2017. Technology change by regulation – a cresting wave?, in Proceedings MetPlant 2017, pp 45–58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By S Juras

To our geologists at Eldorado Gold Corporation, the release of the gold assays on a new ore zone causes a flurry of excitement. But to our metallurgists, that news is often greeted with the question ‘What’s the sulfur grade’? In our company, we operate and manage projects whose end-product will either be auriferous sulfide flotation concentrate or gold doré. Almost all of the steps in the ore processing are related to sulfur (in this paper specifically sulfide sulfur). So why do we geologists wait until late in a project or into production before collecting sulfur data for mine planning and ore control purposes?Gold deposits associated with sulfides commonly use a metallurgical process that begins with a flotation step to recover gold into a smaller mass known as flotation concentrate. Often, this step solely targets the sulfide minerals with gold only coming along for the ‘ride’. As a result, the gold grade in the concentrate is primarily influenced by the ratio of gold to sulfur in the feed. Should this concentrate require a refractory process downstream (eg pressure oxidation), knowing sulfur grade is critical as sulfur controls heat balance in the process. Regardless, we need sulfur models to be as robust as gold models, and created much earlier in the project evaluation process.Sulfur models require quality data collected at the same density as gold samples. Analytical methods must match expected grade ranges and quality assurance quality control (QA/QC) protocols and must be of the same integrity as in use for gold. Sulfur models will then be created by their own data analyses, interpolation protocols and validation. Furthermore, ore control systems should be designed for regular sulfur monitoring to ensure and enhance downstream value. Given time it should become habitual for geologists to likewise ask, ‘And what’s the sulfur grade’, or more specifically, ‘What’s the gold to sulfur ratio’?CITATION:Juras, S, 2017. Sulfur – the new geometallurgical grade in gold-sulfide deposits, in Proceedings Tenth International Mining Geology Conference 2017, pp 199–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By C Fischer

The introduction of digital communications technologies into the underground mining industry, in both coal and hard rock mining, has enabled high bandwidth applications to be applied in the mining industry. Digital networks based on 802.11 b/g/n open Wi-Fi standards have allowed numerous applications to be run over a single communication backbone. One of the many important applications is the tracking of personnel and equipment via RFID Tags. This tracking application has formed the basis of a Proximity Detection System or Collision Avoidance System (Schiffbauer and Mowrey, 2001; Kent, Fischer and Schiffbauer, 2011) thereby improving safety and increasing control in the mining environment. This paper discusses the growth of digital technology as the backbone for communications in underground mining applications. This growth has allowed the ‘convergence of technologies’ (occurring in the general business world) to be available to mine operators in general and underground mine operators in particular. Mine Site Technologies’ involvement with major mining companies and mining equipment manufacturers (OEMs) in developing and supplying their communication systems is also discussed.The latest technical requirements and specifications for communication systems for underground and open cut mines will be reviewed.

Nov 22, 2011

The introduction of a new mining method to Australia is not without its risks and challenges. This paper discusses the processes of planning a new operation, with particular emphasis on block caving and its Northparkes adaptation. As well as applying advanced technologies, here also is the opportunity to develop the art and science of block caving for its application to a wider range of geotechnical conditions than previously Envisaged.

Jan 1, 1995

By J Zhang, O Ostrovski, C Zhang D Cai, Q Wang

The conventional CaO-SiO2-based mould fluxes are not suitable for high-Al steel casting because of the strong reaction between silica in the flux and aluminium in the steel strand. In the process of casting of high-Al steel, flux composition changes; with the decrease of the silica concentration and increase of alumina. Knowledge and understanding of the effect of the Al2O3/SiO2 ratio on flux structure and properties are useful for flux design for the high Al-steel continuous casting. This paper investigated the effect of the Al2O3/SiO2 ratio on structure, viscosity, phase composition of fluxes quenched at different temperatures and heat transfer of CaO-Al2O3-SiO2-B2O3-Na2O-Li2OMgO- F fluxes. It was found that flux melting temperature increased with the increase in Al2O3/SiO2 ratio. Viscosity of the flux melts increased significantly with the increase of the Al2O3/SiO2 ratio from 0.7 to 1.2, reaching the maximum value, and then decreased with further increase of the Al2O3/SiO2 ratio. Raman spectroscopy analysis revealed that the change of the Al2O3/SiO2 ratio led to the change of aluminate and silicate structural units. The turning point for viscosity was attributed to the change in the degree of flux polymerisation. X-ray diffraction (XRD) analysis showed that increasing Al2O3/SiO2 ratio increased crystallisation tendency of the fluxes. Heat transfer measurement by infrared emitter technique (IET) revealed that increasing Al2O3/SiO2 ratio led to the decrease in heat flux which is correlated well with the increased crystallinity of the flux. The results suggested that the flux with Al2O3/SiO2 ratio 4.3 is the best candidate among the studied CaO-Al2O3-based mould fluxes for casting of high-Al steel.

Aug 21, 2024

By A Murphy, D Lauder, J Miranda

Minera Alumbrera Limited operates the Alumbrera concentrator, treating a nominal 80 000 tpd of porphyry gold/copper ore. It is located in Argentina, 1200 km north-west of Buenos Aires in Catamarca Province, at an elevation of 2550 m above sea level. Treatment facilities consist of crushing, SAG and primary ball mill grinding circuits, rougher flotation, ball mill regrinding, gravity recovery and cleaner flotation. It is one of only a small number of concentrators in the world, which uses Jameson Cells alone for cleaner circuit flotation. Plant design was started in June 1995, with commissioning commencing in July 1997. Following a successful ramping up to design tonnages and recoveries, a number of options were reviewed to improve gold and copper recoveries. This paper concentrates on a detailed size by size flotation recovery project, commenced in May 1999. Utilising optical microscopy, scanning electron microscopy and analysis of surface chemistry it has allowed losses by size fraction to be quantified and options for enhanced recoveries to be developed. Coupled with extensive circuit surveys it has also provided an insight into previously unknown properties of Jameson Cell operation. Among these are unique residence time and bubble formation reactions to reagent and pulp flow variations, which has permitted a number of novel changes to the operation to maximise capacity and recovery.

Jan 1, 2000

By P Nissen, T Jenke, M Ralph, M Cattani, M Quinlan

The West Australian Government hold an annual ‘Mines Safety Roadshow’ around the State’s regions and the capital city, Perth. Each year presenters provide an update on legislation and safetyrelated themes. A recurring theme is the mining industry fatality rate. Professor Michael Quinlan’s ‘Ten Pathways to Death and Disaster’ (Quinlan, 2014) has been referenced regularly to assist in structuring workshops and conversations concerning fatality prevention in the mining industry. The ‘Ten Pathways’ are the outcome of an analysis of fatal injuries in the mining industry, which identified a series of common themes to the fatalities: Pathway 1: Design, engineering, technical and maintenance flaws. Pathway 2: Prior warnings or causes for alarm ignored. Pathway 3: Failures in risk assessment. Pathway 4: Failures in management systems and hazard management plans. Pathway 5: Failures in auditing. Pathway 6: Economic pressures compromising safety. Pathway 7: Failures in regulatory oversight and inspection. Pathway 8: Worker and others expressing concern prior to the incident. Pathway 9: Poor management – worker communication and trust. Pathway 10: Emergency and rescue resources and procedures. To determine a fatality risk profile we asked participants at the Mines Safety Roadshows to indicate their perception of their employer’s performance in each of the Ten Pathways. We administered the questionnaire at the Mines Safety Roadshows in 2017, 2018, 2019 and 2023. In this paper, we report on the results of the questionnaires, and suggest how organisations can improve their fatality risk score.

Apr 16, 2024

By H Ishikawa, H Zhou, M Spagnolo, R Halomoan, S Palaniandy

The Karara Mine concentrator commenced operation in November 2012 to produce high-grade magnetite concentrate. The circuit consists of three stages of comminution plus magnetic separation at each stage for early gangue rejection. High-Pressure Grinding Rolls (HPGRs) are used for fine crushing, followed by ball mills and TowerMills in secondary and fine grinding duties respectively. In recent times, the plant throughput rate has had to exceed design by 18% to maintain the targeted concentrate productivity. Meanwhile, the ore hardness has increased by 25% to 15 kWh/t, leading to changes in the circuit operation and design. These changes led to coarser and harder feed to the TowerMill circuit that affects the subsequent separation processes. Nippon Eirich (the TowerMill manufacturer) has partnered with Karara Mining Limited (Karara) to optimise the TowerMill circuit operation to achieve a circuit product with an 80% passing (P80) of 35 µm. Several activities, including a TowerMill circuit audit and performance evaluation, multi-component analysis, modelling and simulation, were carried out as part of the optimisation exercise. The circuit audit results revealed that the TowerMill circuit feed size F80 had increased and ranged from 67–75 µm. The circuit product P80 ranged between 42–55 µm. The average circuit specific energy was 3.4 kWh/t. Moreover, the differences in density between magnetite and gangue minerals had affected the hydrocyclone performance where the efficiency curve exhibits coarse end deflection indicating that low-density coarse material was bypassing to the overflow stream. A multi-component analysis was carried out to further investigate the coarse end deflection of the hydrocyclone efficiency curve. The analysis showed that the magnetite and gangue minerals had different cut sizes of 32 and 64 µm respectively. Furthermore, 33% of the magnetite (below 35 µm) was being recycled back to the mill due to the density effect. Based on these findings, several recommendations for process improvement were identified and implemented including:• converting to a bottom feeding configuration to improve the grinding efficiency in the mill• additional grinding power in the fine grinding duty to compensate for the increase in plant throughput and ore hardness• improved classification efficiency by converting to smaller size hydrocyclones. Simulation studies carried out to evaluate the impact of these implementations had indicated that a P80 close to 35 µm with a steeper size distribution could be achieved by using the bottom feed configuration with additional grinding power. The TowerMill circuit was converted to bottom feed configuration and the performance was evaluated. The operating work index, size specific energy and circulating load were 30% lower than the top feed configuration, indicating that the bottom feed configuration had a higher grinding efficiency. This paper discusses the outcome of the circuit audit, multicomponent analysis, circuit simulations, improvement strategies and quantification of the improvements. CITATION:Palaniandy, S, Spagnolo, M, Halomoan, R, Zhou, H and Ishikawa, H, 2017. Fine grinding circuit process improvement at the Karara mine concentrator, in Proceedings MetPlant 2017, pp 101–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By J J. Cilliers, K Hadler

Air is fundamental to flotation; not only is it required to collect the valuable particles, but it also controls the froth stability and consequently the separation performance for a given feed. Froth stability can be described and quantified in numerous ways, which are subtly different. Air recovery is one such measure of froth stability which accounts for both the stability of the bubbles and the mobility of the froth. The benefit of using air recovery as a measure of froth stability is that it exhibits a peak as air flow rate is increased, and this corresponds to the air rate at which the optimal separation performance is obtained. As such, it provides a single target value for optimising air flowrate for a given set of feed conditions. Use of air recovery, however, has one potential drawback: accurate measurement of the inlet air flow rate to a flotation cell is required. This can be problematic for operations, particularly where calibration of air flow rate is carried out infrequently or where there is no air flow rate measurement, such as for many self-aerated flotation cells. To this end, we present an alternative method for determining the peak in air recovery (PAR) air rate.We introduce a simplified method for determining the PAR air rate using trends in froth velocity and overflowing froth height, both of which are readily measured using existing froth image analysis systems. We will show, using industrial data, the application of this simple technique to find the optimal air flowrate for flotation cells. We will also discuss other alternative techniques for air rate optimisation that have the potential to improve separation performance using existing technology.CITATION:Hadler, K and Cilliers, J J, 2018. How to find the optimum air rate for flotation cells, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 377–384 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Guarascio M, Massacci P

In process simulation, more reliable prediction of industrial results and evaluation of data for design purposes and process optimisation may be attained by the combined use of: the modelling and simulation of ore characteristics, and 2. the modelling and simulation of the process. It is well known that geostatistical methods allow the defining of models of orebodies in which the variables considered are the grades of the valuable components. These models are proper for reserve estimation, geostatistical contouring, design and simulation of the exploitation method, and, in addition, for evaluating the variability of the ROM which is expected to be fed to the processing plant. However, no data are normally incorporated in the orebody model in order to evaluate the ore characteristics relevant for a reliable process simulation. The procedure for process simulation aimed at predicting plant results normally used so far consists in collecting samples from different orebody sites and building up a so-called 'representative sample'. On this sample, the ore characteristics (eg liberation, washability, grindability, etc) and the processing tests are referred to as the 'average behaviour in the orebody', assumed constant. A more reliable methodology consists in collecting samples from different orebody sites, in performing tests to characterise the samples from the point of view of the process (ore patterns), and in using synthetic parameters (process features). The values of the parameters are processed using geostatistical methods in order to develop a model for simulating the feed to the process. The estimation may thus be referred to the amount of recoverable minerals instead of to the existing minerals. Furthermore, the selection of the processes, the sizing of equipment and the design of control devices, as well as the prediction of results, become more accurate and reliable.

Jan 1, 1993

By S Hapugoda, J R. Manuel, M J. Peterson, A Poliakov, E Donskoi

The occurrence and deportment of manganese in a number of ferromanganese and Mn-bearing iron ore samples from supergene-upgraded deposits, as well as from magnetite banded iron formation (BIF) and magnetite skarn deposits, was characterised in order to provide a basis for improved understanding of the processing characteristics of different ore types and investigate the potential for development of a robust geometallurgical classification for Mn-oxide ores. An understanding of the Mn mineralogy in mixed Fe-Mn deposits is necessary to inform any attempt to separate the Fe and Mn during beneficiation and to understand and predict the behaviour of lump and fine ore products during processing.A suite of analytical techniques was utilised, including hand sorting of lump ore particles, optical microscopy, X-ray fluorescence (XRF)/inductively-coupled plasma mass spectrometry (ICP-MS) chemistry, X-ray diffraction (XRD), scanning electron microscopy (SEM)/electron probe microanalysis (EPMA) and gas and solid phase pycnometry, in order to elucidate manganese mineralogy, mineral chemistry and mineral textures. Manganomelane group minerals (eg cryptomelane, hollandite), pyrolusite and lithiophorite were the most common manganese oxides in the samples examined. From the microprobe work, there was evidence of probable substitution of Mn, as well as Al and Si, into the structures of goethite and hematite. Manganomelane minerals were often intimately associated with goethite, in particular, and a clarification of this association and the associated Si and Al impurities is fundamental for improved understanding of beneficiation and sintering behaviour of Mn-oxide ores. Due to the poor or very fine crystallinity of some supergene manganese deposits and of some Mn oxide minerals, in particular the extent of overlapping peaks and their variable mineral chemistry, XRD was a problematic technique to equivocally determine Mn mineralogy.For lower-grade, earthy, poorly microcrystalline ores the mineralogical and textural association between mixed Mn, Fe and Al (¦ Si) phases was also critical. The deportment and potential separation of these elements in these deposits, especially Al, was complex, as they were characterised by forms of æhydrousÆ cryptomelane with higher levels of Fe-Al-Si substitution, as well as intimate intergrowths of ochreous-earthy goethite (probably aluminous in part) with cryptomelane, lithiophorite and/or kaolinite.Trace amounts of alkali elements in ferromanganese deposits were considered likely to be preferentially structurally associated with Mn oxides, while lateritic deposits with significant amounts of lithiophorite could contain elevated levels of deleterious impurities; Co and Ni in particular.A combination of solid and gas phase pycnometry proved to be a useful technique for broadly discriminating hematitic, goethitic and mixed Mn oxide-goethite lump particles based upon differences in their envelope and apparent densities. Based upon these preliminary results and ongoing Raman spectroscopy work on manganese deposits sensu stricto, Raman spectroscopy is a technique considered to have promise during targeted research to better link the optical and compositional properties of ferromanganese ore particles. CT-scan (computed tomography scan) analysis could also be combined with Raman spectroscopy and pycnometry to link mineral composition, mineral texture, ore particle textures and particle porosity/permeability to the high-temperature processing behaviour of lump and fines products.CITATION:Peterson, M J, Hapugoda, S, Manuel, J R, Donskoi, E and Poliakov, A, 2013. Textural characterisation of manganese minerals to improve the geometallurgical characterisation of ferromanganese and iron ores, in Proceedings Iron Ore 2013 , pp 281-300 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By T Hausler

The pitfalls, pleasures and management issues associated with international and remote projects are diverse.However, no problem is insurmountable and if an engineering team chooses (by luck or good planning) to push through the difficulties, success can mean an extremely satisfying experience for individuals and a significant, positive result for an organisation.International projects are not for the faint hearted or inflexible. Working in foreign lands with people who may or may not speak English and who may not initially respect you can become mentally and physically tiring.Sometimes the challenges are not fully explained to individuals in advance. Individuals then often learn about the challenges ù and discover solutions ù on the job. While this initially puts great pressure on individuals, matters improve eventually, especially when the locals come to understand that you are on site to make a positive difference.This paper will discuss aspects of a recent international project including meeting international clientsÆ expectations, dealing with cultural differences, social reckoning, environmental issues, and personal challenges. Specifically, it will cover aspects of working within a Russian cultural setting and overcoming social barriers.The paper also presents coping strategies for long periods of time spent away from home in remote places with extremes in weather beyond the normal experience of most Australians. For example, dealing with the effects of the spring thaw and coping with temperature ranges of -45 to +45¦C.Lastly, and possibly most importantly, there will be a focus on the role of translators. They have the power to make an engineer everyoneÆs best friend or, on your behalf, to order cold chicken liver and heart salad for lunch. If an engineering team can establish a working relationship with translators, they can become an invaluable asset and both on and off site.CITATION:Hausler, T, 2013. Achieving success in large-scale, remote area metallurgical plant projects, in Proceedings MetPlant 2013 , pp 539-552 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By D Morgan, K Jones

"In March 2015 Northparkes Mines (NPM) installed a process mineralogy facility on-site. The laboratory included a TESCAN TIMA scanning electron microscope (SEM) and was the first SEM facility to be commissioned on a mine site in Australia. While the initial intent of the quantitative mineralogy laboratory was to provide information to drive processing plant improvements, in practice, it has been utilised for so much more and is now serving as an integral link between departments on-site. This multidisciplinary approach to orebody knowledge is a new strategy for NPM whereby all parts of the value chain are aligned towards the common goal of achieving process efficiency and stability while still maintaining high throughputs. The NPM experience is presented as a case study to illustrate how on-site process mineralogy can drive a realignment in business strategy with a common goal of mill optimisation, stability and more realistic forecasting through orebody knowledge and information sharing between disciplines.Citation:Jones, K and Morgan, D, 2016. On-site Process Mineralogy - Linking Departments and Disciplines with the Common Goal of Increasing Plant Performance, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 149–156 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By Quast K

A series of laboratory flotation tests were conducted to evaluate the effectiveness of various depressants as arsenic (and zinc) depressants in the lead cleaner stage of the NBHC mill at Broken Hill. The depressants used included potassium cyanide, ferrous sulphate, sodium hypochlorite, potassium ferricyanide and two Cyanamid commerical depressants, Aerodepressants 610 and 633. A standard roughing stage was completed before the addition of the reagents in the cleaning stage. All reagents tested produced significant arsenic depression, with the best results being obtained with the addition of potassium cyanide and sodium hypochlorite. Some of the depressants activated the zinc in the process of arsenic depression. The best result was obtained with the addition of 90 g/t potassium cyanide at a pH of 10 when arsenic recovery was only 1/4 that of the value obtained for the standard test.

Jan 1, 1991

The sixth international symposium on mining with fill nearly coincides with the 25th anniversary of the Jubilee Symposium on Mine Filling. That symposium, held in August 1973 in Mount Isa, in part to commemorate the 80th anniversary of The Australasian Institute of Mining and Metallurgy, was the first in what has turned out to be a very successful series of symposia. Subsequent symposia were held in Sudbury, Canada (1978), Lulea, Sweden (1983), Montreal, Canada (1989) and Johannesburg, South Africa (1993). The series of symposia has now become an established part of the mining industry calendar, and it will be interesting to see which country is given the honour, and accepts the challenge, to organise the next symposium. When the chairman of the conference organising committee invited (or was it instructed?) me to prepare and deliver one of the keynote addresses, his request was for me to be in parts historical, controversial, predictive and entertaining. The mix was left to me, with one proviso - that an early pioneer of mine filling in Australia be given due recognition. The chairman of the organising committee alone will be able to determine if I fulfilled the last objective. My success, or otherwise, with the other objectives will have to be judged by my fellow delegates. One way of predicting the future, or some small part of it, is to revisit where we have already been with a view to determining the existence of any trends that may impact on the future. An historical review of filling practice and research, with special emphasis on Australian experience in particular and worldwide in general over the previous 25 years, will enable me to address the historical and predictive objectives.

Jan 1, 1998

By Urie R. W

Fluidized bed roasting of copper concentrates from Mt. Morgan, Mt. Lyell, Mt. Isa, and Peko was performed in a 3 ft 6 in diameter, slurry fed, pilot plant roaster operated under autogenous conditions to produce calcines with desirable leaching properties. A 12 in. diameter, externally heated roaster, provided with a dry feed system, was also used.An account is given of important factors which influence roaster behaviour and performance, and the effects of operating variables on calcine composition and leaching properties are described. Due to copper ferrite formation, a maximum of approximately 50 per cent of the copper in the calcines may be in the form of CuO before the copper leach efficiency falls significantly below lOO' per cent. Recovery of gold by cyanidation of leach residues was consistently high and independent of roasting conditions.INTRODUCTIONIn traditional practice copper is produced by pyrometallurgical techniques when the ,copper minerals in the ore or concentrate are predominantly sulphides, and by hydrometallurgy when the minerals are oxidized. Copper smelting is most suited to large scale operations, and for many years small to medium size mines with sulphide orebodies have been interested ill; alternative processes.Since hydrometallurgical plants (ie. leaching and electrowinning plants) are essentially unitized, they may be scaled down in output without much loss in efficiency or increase in processing cost, and many proposals have been made for the application of this type of process following roasting of the sulphides to render the copper soluble. However, until the advent of fluidized roasting, it was not possible to control the roasting operations sufficiently precisely to produce calcines consistently of the required leaching characteristics.

Jan 1, 1961

By A D. Campbell

Conversion of Mineral Resources to Ore Reserves requires a multidisciplinary approach and application of a number of Modifying Factors. The Modifying Factors for mining, particularly dilution and recovery in a caving mine are complex and can be difficult to determine. Cave flow modelling software is widely used for mine planning, scheduling and forecasting metal production. However, the conversion of Mineral Resources to Ore Reserves remains a difficult and subjective process and a consistent approach to convert Mineral Resources to Ore Reserves as part of the cave flow modelling process is not published in the literature. This is due to the difficulty in estimating the Ore Reserve that remains as cave stocks at a particular point in the mine schedule, the recovered tonnage and grade of the diluting material at various stages in the mine life, as well as the Mineral Resource classification of both the recovered and diluting material that forms the Ore Reserve. The key principle of this paper is the tracking of the Mineral Resource classification in the flow model used to estimate the Ore Reserves. This is critical to defining the Ore Reserve as Proved or Probable and enabling transparency in the reporting process. An approach for dealing with mineralised external dilution in the Ore Reserve estimation process is also provided.This paper outlines the approach to convert Mineral Resources into Ore Reserves developed at the Ernest Henry mine sublevel cave (EHM SLC). The same method could be used in any cave mine and applied at any stage of the mine life. The process replaces broad-brush assumptions for the mining Modifying Factors, such as dilution and recovery, as these are determined numerically as part of the model computation. This paper explains the Ore Reserve estimation method with a worked example to enable the reader to adopt the process at any caving mine. Mineral Resource classification within the block model is embedded in the cave flow model and the flow model results used to attribute tonnes, grade and the mixed proportions of the Mineral Resource classification for material extracted from each drawpoint. This information is then used to convert planned mine production into the appropriate Ore Reserve classification. Since the flow model simulation follows the mine schedule, it can be used to predict depletion and cave stocks at any stage of the mine life, and can calculate a residual block model at the end of the mine life. The accuracy of the flow model is checked by validating the forecast ore grade and metal tonne with reconciliation data from the concentrator which is also used to calibrate the flow model.CITATION:Campbell, A D, 2017. A simple and accurate method for Ore Reserve estimation and Mineral Resource depletion in caving mines, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 253–260 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By J A. Wells, K G. Thomas, R F. Dewhirst

"One of the contributing factors to the extreme cost escalation in the first decade of the 21st century was the increase in the amount and cost of engineering work that went into studies and projects. Various reasons for this were identified, including unsatisfactory productivity due to a shortage of experienced/qualified engineers, the increased complexity and infrastructure requirements of many projects due to location, metallurgy that is more challenging and increasing environmental and social requirements. These conditions often led to unsatisfactory project results in terms of cost and schedule blowouts and created a loss of confidence – both internally and externally – in the industry’s ability to complete projects on time and on budget.Technical fundamentals aside, the experience and effectiveness of project teams has had, and continues to have, a major impact on project cost, schedule and ramp-up to nameplate capacity and operating parameters. There are unfortunately too many examples of where project teams have not been as effective as they could or should have been, all to the ultimate detriment of the project.Using the authors’ extensive experience on both owner’s and engineer’s teams, this paper discusses some of the main reasons for suboptimal team, and hence project, performance and offers thoughts on how best to build and maintain project teams. The analysis and conclusions drawn are built around the Tuckman model of group development known as ‘forming-storming-norming-performing’, which was first proposed some 50 years ago. Given the importance of good teamwork to project success, understanding how project teams grow and become efficient and productive is an essential part of good project management that should receive more attention.CITATION:Dewhirst, R F, Thomas, K G and Wells, J A, 2016. Building and maintaining effective project teams, in Proceedings Project Evaluation 2016, pp 38–48 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016