Search Documents

By X Dahe

SLon vertical ring and pulsating high gradient magnetic separators possess excellent mineral processing ability and have been widely applied to process oxidised iron ores. SLon centrifugal separators are applied to clean the SLon magnetic concentrate and remove quartz and other gangue minerals associated with a small portion of magnetite.This paper introduces the application of this technology in Hai Nan, Da Hong Shan and An Shan for processing oxidised iron ores.

Jul 11, 2011

The successful operation of diesel equipment underground does not entirely depend on selection of robust, reliable, easily maintained machines. Results are also heavily influenced by the following factors: Design and condition of the operating area. Skill of operators. Correct maintenance facilities. Experience, skill and initiative of maintenance personnel. If the mine layout does not allow access to a central workshop area, the effect of any shortcomings will be magnified. The best results will only be obtained by close co-operation between mining and maintenance departments right from the initial planning stages.

Jan 1, 1977

By E Amini, N Beaton

Application of ore pre-treatment technologies such as Grade Engineering and in-pit ore treatment require comprehensive analysis to show proven value is being generated by switching away from the current practices. Considering most mining operations last several decades; the pre-treatment technologies must be investigated over life of mine (LOM) to truly show value was generated or lost. Therefore, a value chain flowsheet model has been usually developed to run those analysis/simulations over LOM using a set of defined ore characteristics and the operating equipment capacities. The Integrated Extraction Simulator (IES) has been used for this type of LOM simulations as it has the necessary flexibility to accommodate the whole mining value chain flowsheet in one platform and provide essential computation power to run mass simulations for the given scenarios using the resource block model. This allows to forecast the value chain response over the LOM for all given scenarios in a feasible amount of time. The traditionally developed flowsheets for the analysis/simulations are usually limited to the mineral processing plant and were developed based on a single audit conducted on the plant in a very short time, e.g. several hours. The process plant is being operated with a certain ore at a certain condition during the short audits which would not reveal the true capacity of the operation equipment when ore characteristics changes. Therefore, it would be impossible to define the true capacity of the equipment and identify the constraints along the value chain. In this study, a methodology was developed to identify the constraints along the value chain and implement those in the IES flowsheet using process information. Also, the equipment models were fine-tuned to represent the true capacity of the equipment in the flowsheet using the same data set. The methodology was tested over five process plant in two operations and showed the performance forecast was significantly improved over the traditional methods being used so far. Then those high-fidelity flowsheets were used to evaluate the ore pre-treatment technologies proposed by the relevant resource company experts.

Nov 10, 2020

The scheme of rehabilitation of surface plant commenced in 1936, included the provision of improved and more hygienic changing and bathing facilities for the employees.At that time the Thompson's Shaft section of the British Mine was being prepared for a resumption of operations, and it was decided to repair and re-equip the existing building. Thus any new scheme adopted could be given a thorough trial, and the proved arrangement used as a basis for the contemplated new main changehouse on the North Section.Investigations were carried out to determine the most suitable arrangement for the Thompson's Shaft changehouse, to provide for a total of 120 men, with particular regard to the internal fittings and fixtures. Also, as the mining conditions were such that a large proportion of clothes worn underground by miners, etc., were wet by the end of the shift, the problem of drying these clothes in the availaole time from a man coming off shift to his commencing again some sixteen hours later was one of the most important to be dealt with.The changehouses in use on the North mine section of the lease were provided with racks around the walls for the men to hang their street clothes on, and a section was partitioned off to house the mine clothes and their drying facilities. The actual drying was carried out by means of hanging the wet clothes over racks between which ran pipe coils heated by means of hot water circulated from the hot water boiler supplying the showers.This method had proved to be far from satisfactory for several reasons, the main objections being:-

Jan 1, 1940

By T Kojovic, S J. Windle, J Sullivan

"The Geometallurgical Mapping and Mine Modelling (GeM) comminution index (CI) was developed as part of the AMIRA P843 GeMIII project. Drill core geochemistry samples were passed through a Boyd Crusher with standardised settings and the resulting particle size distribution (PSD) was measured using sieves.Disadvantages of the original measurement were the relatively coarse crush size, requiring a second pass of crushing for geochemical sample preparation, and the limitation of throughput caused by the sieving step. At Antamina, the measurement has been modified to use a 2.2 mm crusher size setting, which permits a single pass. The PSD is measured using a Camsizer, an automated optical sizing instrument. The Camsizer sample is a +180 µm fraction, used to avoid passing too many fines through the instrument and slowing down the measurement. In the sieving step, the weights of the two fractions are recorded and subsequently used to normalise the distribution measured by the Camsizer. In this way, the throughput of the Camsizer can match that of the Boyd Crusher. The PSD data are therefore measured without penalising the throughput of the sample laboratory.The normalised PSD distributions are used to derive modified CI parameters, based on the slope and intercept of the breakage product size distribution, which are indirect measures of the material breakage hardness.Fifty samples were selected as a training set, each sample a composite of five or six individual assay intervals and each with its own measured CI. The average PSDs were calculated for the composites and used to calculate a composite CI. The intact half of the core, approximately 40 kg, was tested to measure the BWi, A*b and crushability. The results were used to develop predictive algorithms for these hardness parameters.A further 50 composites were chosen for lab testing, to serve as a blind test of the algorithms. The paper reports on the test results and the incorporation of the modified CI data and predicted hardness parameters into the Antamina block model.CITATION:Windle, S J, Kojovic, T and Sullivan, J, 2016. Use of a Modified Comminution Index to Predict Bond Work Index and SMC A*b at the Antamina Mine, Peru, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 153–160 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By C Zschiesche, alam, A Abadias Llamas, A K

Lead has the ability to collect and carry valuable metals such as copper, bismuth, antimony, tin and precious metals for their downstream recovery. Therefore, lead metallurgy is key for the raw material supply that our society demands. Lead smelters, excluding lead-acid battery recyclers, tend to process more complex primary and secondary raw materials, which are mostly processed via the pyrometallurgy route. Accordingly, understanding the slag system of these metallurgical processes is key for the efficient industrial operation and recovery of minor elements. Glencore Nordenham is an integrated lead and zinc smelter in northern Germany with a production of 92 000 t of lead and 164 700 t of zinc in 2022. The lead production line processes complex leadbearing raw materials through the direct smelting process. Firstly, the feed mix is smelted in a Top Submerged Lance (TSL – Ausmelt®) furnace, where a lead bullion containing minor metals and a lead-rich slag are produced. Then, the lead-rich slag from the TSL is tapped (via launder) into a Side- Blown Furnace (SBF), where lead oxide is reduced to produce lead bullion (with minor elements) and discard slag. The lead bullion from both stages is refined to produce lead (>99.9 per cent) and recover the minor elements (Cu, Ag, Au, Sb, Te, Bi etc). This paper reflects the experience of operating the SBF after the first five years of operation and describes its ‘PbO-SiO2-FeOx-CaO-ZnO’ slag system. Firstly, the slag system, the furnace operating region and the potential solid phases present are discussed from a theoretical point of view. This theoretical study has been performed using FactSage™ 8.2 and the database developed by the Pyrosearch group at the University of Queensland, Australia (UQPY). Then, the FactSage™ simulations are compared with industrial slag measurements. Finally, some examples on how the slag knowledge gained at Glencore Nordenham can help the industrial operation of the SBF are discussed.

Jun 17, 2024

By M I. Pownceby, N A. S Webster, J R. Manuel, J M. F Clout, E Donskoi, N A. Ware

The relative influences of sinter mineralogy, sintering temperature, solid and pore macro- and microstructure on iron ore sinter physical strength are not yet fully understood. Whilst a range of analysis techniques have been used by researchers to evaluate sinter physical properties and sinter mineralogy, none have been able to directly link sinter mineralogy and physical strength under controlled conditions. CSIRO has developed a unique laboratory method to study the fundamental melting properties of fine iron ores in a laboratory furnace under a controlled temperature and gas atmosphere environment designed to simulate the industrial sintering process. Compacted tablet samples for a 0.41 per cent and a 2.5 per cent Al2O3 series were fired in a tube furnace at various temperatures, cooled, then tumbled using a modified Bond abrasion test apparatus to determine a relative tumble index (TI) at each temperature. Quantitative XRD (QXRD) analysis was then carried out on the tumbled samples and optical image analysis (OIA) was conducted on polished sections of a separately fired compact in each case. The amount of total SFCA was found to decrease with increasing firing temperature for both alumina series with the total amount of SFCA higher in the 2.5 per cent Al2O3 series compared to 0.41 per cent Al2O3 series samples. The increase in the amount of magnetite and hematite with increasing firing temperature was largely at the expense of a decrease in total SFCA. Overall, there was good agreement between the quantitative mineralogy determined from QXRD versus OIA for SFCA, hematite and magnetite. Qualitative analysis of high magnification images of the sinter correlated with both the OIA and QXRD results.

Sep 18, 2023

By Cawte D. C, Just G. D, Whitchurch K. D

The stringent marketing specifications included in coal contracts mean that coal producers must supply cleaner and more consistent coal than may have been formerly required. Geostatistics has the potential to aid in the accurate estimation of the washability characteristics of coal. A prediction method, the Kriged Service Variable Approach has been developed.A Computer Aided Drafting and Design system has proved useful in the development and application of the approach. The geostatistical approach has been tested against coal geological and borehole data and applications discussed.

Jan 1, 1987

By R Moller

Reconciliation at large iron ore operations is a complex and time- consuming process. Often the volume of data and the large range of different stakeholders makes the process almost impossible. Up until recently geologists and engineers at these operations would spend hours cutting and pasting data in and out of monster spreadsheets, diligently comparing how resource/reserve models, grade control and survey pick-ups compare to what was actually produced. In 2003 the Sishen Iron Ore Mine in South Africa broke this cycle by implementing SnowdenÆs Reconcilor software. The implementation of a dedicated reconciliation system required a number of existing practices to be changed, with the involvement of stakeholders right across the mine. Data sources had to be clarified and validated, terminology had to be standardised, processes needed to be documented and some methodologies needed to be updated. This was a task that required significant effort by Kumba personnel so that the system could be successfully implemented. This paper provides a case study of the reconciliation system implementation at Sishen. It is a story of an operation that evolved from using a number of fragmented reconciliation processes to using a unified automated system. This paper outlines the key estimates and measurements that are used for reconciliation, details the characteristics of an automated web-based information management system to facilitate the process and provides some insights about the benefits that have been gained though the use of a rigorous reconciliation process.

Jan 1, 2005

By MáAndrusiewicz, M M. Hilden, M S. Powell, P D. Kay, B Foggiatto

Circuits with unconventional and potentially more complex designs are predicted to become more common in the future as plant designers and operators look to process ores more efficiently. Ideas have been presented on how circuit design may be changed to utilise todayÆs technology to address tomorrowÆs challenges (Powell and Bye, 2009; Powell, Benzer and Mainza, 2011a). High pressure grinding roll (HPGR) installations in various configurations; application of preconcentration plants eg sorting, magnetic or gravity separation; and preweakening devices eg microwave processing; are all examples of technologies having the potential to deliver a significant reduction in comminution energy for ores amenable to these processes. Not only will future novel circuits contain equipment for which models are not as well developed (if at all), many will likely require the ability to respond to variations in feed, and interact with geometallurgical models requiring process adjustments when the ore characteristics change.In order to confidently simulate more complex circuits and accommodate variations in feed type, a significant advancement in modelling and simulation capability is required. This includes dealing with multiple components in the feed, accommodating different competencies of ore, utilising physical separation opportunities and tracking the grade reporting along the different potential processing routes. Developing the means to simulate complex circuits has been a key priority of a collaborative group of comminution researchers working to solve these challenges.Simulations are presented utilising a new configurable simulation interface called the model developers kit (MDK). The MDK is designed to accommodate multi-components and incorporate new models under development. These will be used to demonstrate the potential of flexible circuit design, based on measured ore properties and equipment performance.CITATION:Foggiatto, B, Hilden, M M, Powell, M S, Kay, P D and Andrusiewicz, M, 2012. Simulation of flexible circuits, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 291-298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By A Batnasan, K Haga, A Shibayama, K Higuchi, H Takeuchi

High silica (SiO2), alumina (Al2O3), and phosphorus (P) contents in iron ore adversely affect the quality of iron products. The removal of those impurities from iron ore is an essential point in further iron ore processing. In this paper, the removal of P, SiO2 and Al2O3 impurities from iron ore by alkaline drying followed by reverse cationic flotation is discussed. The reverse cationic flotation experiments are performed using the iron ore samples without and with alkaline drying pretreatment. All other flotation conditions except pulp pH (4–12) and particle size distributions (-45 to -250 μm) are held constant. A typical collector and frother, such as dodecylamine acetate (DAA) and methylisobutylcarbinol (MIBC), are used in the flotation experiments. Alkaline treatment is conducted before flotation using sodium hydroxide at fixed conditions. The impact of alkaline drying on the performance of iron ore flotation is evaluated based on the removal rates of P and SiO2 + Al2O3, iron grade, and iron recovery compared with the iron ore flotation without alkaline drying (direct flotation). X-ray diffraction (XRD) analysis indicates hematite and goethite are the main minerals in the iron ore, which assays 62.8 mass per cent Fe, 0.232 mass per cent P, 7.1 mass per cent SiO2 + Al2O3 (total) determined by X-ray fluorescence analysis (XRF). Results indicate that a combined approach is more effective for removing P and SiO2 + Al2O3 impurities from iron ore than the direct processing technique because the maximum removal rates of P and SiO2 + Al2O3 are 48.2 per cent and 66.5 per cent from the alkaline dried iron ore when 8.4 per cent and 13.1 per cent from the non-alkaline dried iron ore.

Sep 18, 2023

By P A. Kirsch, A Hine

Mining is a major global industry that requires the moving of considerable volumes of earth and rock (overburden) to win the valuable ore prior to mineral extraction and processing. As a result of this process, new landscapes are created, both extracted voids and overburden piles, as well as infrastructure for management of mine operations, wastewater, tailings, other raw materials, transportation and extreme rainfall events. Resource companies must develop and obtain regulatory approval for detailed plans that manage this displaced material through all phases of the life-of-mine and rehabilitate the site at the time of closure (including landform stability, revegetation and ongoing management).Individual mine sites operate in long time frames (ten to 50 years), with several mines often operating in the same region, generating cumulative overburden volumes and heavily altering the original landscape. These impacts are universally framed as a negative consequence of the industry, especially by modern society that values natural (and some agricultural) landscapes as pristine and almost sacred. Overburden and tailings are also seen as a problem, and are a significant business cost to mining practice.This paper looks to investigate perceptions of mining and post-mining landscapes, questioning the aesthetically driven emphasis on the ‘natural’. It proposes instead an opportunity to reframe the way we look at overburden and landscape impacts from mining, exploring the possibility of imagined post-mine landscapes unburdened by traditional aesthetic expectations. These landscapes, to be conceived by regional stakeholder roundtables, have the capacity to be built by regional mining consortia as a foundation for sustainable post-mining economies.Post-mine regeneration offers both the motivation and the basic materials to create an altogether new environment from a blank slate. Few circumstances allow the opportunity to truly explore a re-envisioning of the land on a huge scale, and the possibilities merit serious consideration.CITATION:Hine, A?and Kirsch, P?A, 2014. Dreams of futures past – curating post-mining landscapes, in Proceedings Life-of-Mine 2014 , pp 121–138 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

Standards in the public reporting of resources and reserves in Australia have dramatically improved since the implementation of the Australasian Code for Reporting of Mineral Resources and Ore Reserves (The JORC Code) in 1989. Whilst the JORC Code states clearly that Mineral Resources and Ore Reserves are imprecise calculations and should be treated as estimates, there is strong evidence that many people regard them as fact, including some accountants, directors, auditors and investors. Mineral Resources and Ore Reserves are key inputs in the valuation of a mining company and the determination of financial performance. Geological knowledge is the foundation upon which Mineral Resources, Ore Reserves and investment decisions are made, however this information carries with it substantial uncertainty. Case studies and company reports have established that errors derived from inadequate geological inputs have led to reduced profitability in operating mines and in extreme cases the premature closure of mine operations. Whilst there are many causes of mine closure and reduced profitability, including commodity prices and exchange rates, the cumulative effect of all geological uncertainty contributes significantly to the erosion of the credibility of mining within the investment community. There are a number of methods used to characterise and model uncertainty in Mineral Resource and Ore Reserve estimation. Empirical mining indexes, sensitivity analyses, Monte Carlo simulations and Conditional simulations are used to identify and estimate geological uncertainty, notably the quantification of uncertainty in grade and tonnage estimates. These techniques have not generally been applied to estimating geological uncertainty associated with key Ore Reserve inputs such as appropriate mining technique, equipment selection, production rate, mining dilution, stability requirements, materials handling, metallurgical processing, product quality and waste storage. New software tools are needed to model the entire mining process with all its geological and other interdependencies, enabling all uncertainties to be separately identified and estimated. By its very nature, mining involves the assumption of significant technical, financial, political, environmental and social risk. Success comes by understanding and managing these risks and consequently the mining industry will never choose to reduce the level of geological uncertainty to nil. The ultimate aim of improved identification and estimation of geological uncertainty is to quantify inputs into the Ore Reserve process, allowing a company to assess the risks and manage these accordingly. This approach is relevant to feasibility studies for new projects as well as life-of-mine planning through to the weekly schedule at existing mines.

Jan 1, 2003

By I Gray

This paper examines the practical limitations that affect the measurement of stress in rock. As most rock stress measurement is conducted through the invasive process of drilling a hole in a rock mass, the nature of the rock and its response to being drilled form the basis of the stress measurement process. The prime techniques to measure stress down a borehole are to conduct hydraulic fracturing and its variant hydrojacking, overcoring, and the examination of the borehole wall for breakout or tensile fracture. It is also possible in some circumstances to use the sonic velocity within the rock mass as an indicator of the stress situation. Other structural indicators of stress such as joints, faulting and intrusions are useful but may not reflect the current stress situation within the rock mass. The variability of stress within the rock mass also needs to be considered as it is quite unusual to have a monotonic stress situation throughout any rock mass. The outdated concept of measuring the far field stress in a few measurement for use in a numerical model is quite dangerous. It is essential to make multiple measurements and to generate an understanding of its distribution in some form of model before stress can sensibly be incorporated into underground design. CITATION:Gray, I, 2018. The practicalities of effective stress measurement in rock, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 360–374 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

ILZRO sights are locked securely on the targets of the expanded applications and ever-improving quality in the major market for zinc-coated steel. A wide range of ILZRO-sponsored research projects examine issues of formability, paintability, and corrosion resistance for traditional hot-dip galvanising, electrogalvanising, and ILZRO's own proprietary zinc coating, Galfan. Recent research has focussed on the on the interaction between Galfan and different substrate steels to determine optimum combinations for different applications. ILZRO enjoys an evolving role in providing the connection between research laboratories and marketing divisions through supporting research and services for the Galfan Technical Resource Centreò(GTRC) and the recently formed North American Galfan Development Authority (NAGDA). GTRC has just produced a new problem-solving manual that provides a comprehensive source of hands-on solutions for the many Galfan licensees throughout the world, and should contribute substantially to the reputation of Galfan as a consistently top-quality steel-coating product. Meanwhile, NAGDA is advancing the market with new advertising for Galfan based on superior corrosion-resistant qualities proven through ILZRO-sponsored research. Practical manufacturing issues remain at the forefront of ILZRO priorities, with research emphasis on cutting and welding zinc-coated steel to provide direct assistance towards improved product quality and a more secure market. Moving to the arena of die casting, when the specifier looks to zinc to fill a design need, ILZRO-sponsored research projects provide comprehensive documentation on metallurgical characteristics for every zinc alloy under almost any imaginable application. On-going ILZRO-sponsored research is integrating this wealth of data with sophisticated computer programs that model die-casting designs with ever-increasing accuracy, as other ILZRO projects lay the market groundwork for zinc in applications ranging from vibration damping to electromagnetic shielding.

Jan 1, 1993

By Aalbers J. P A

The State Electricity Commission of Victoria (SECV) operates 13 excavators, 3 travelling stackers and 4 mobile slew conveyors in their three open cuts in the Latrobe Valley. The majority of these machines have been designed and constructed to a German design code current at the date of order. The SECV has always ensured that the machines were manufactured and erected to the appropriate standards. The SECV has a policy of having all machines inspected by an independent inspector every two years. These inspections are based on those carried out in Germany. The inspections have been carried out by inspectors from Germany who have the necessary experience to do similar work in German open cuts. Major faults found during the inspections have been repaired, however,the gradual breakdown of corrosion protection system has continued. The structures on some machines have areas of bad corrosion. This, coupled with wear on major mechanical equipment, would require an extensive outage to overhaul the machines. Refurbishment of Hazelwood Power Station will result in higher levels of production and extended life for the station. This will require improvement in the total output from Morwell Open Cut (MOC). To meet this increased coal demand, the open cut equipment will need to operate more efficiently and for a longer period of life.

Jan 1, 1989

By Z Tong, M Gao, X Wang

In response to the need for improved magnetic separators for beneficiation of fine grained iron ores that have been finely ground to liberate the iron minerals from the gangue, a series of high efficiency wet drum permanent magnetic separators (T-GCT) has been developed by Maanshan Tiangong Technology Co Ltd. These magnetic separators have high efficiency for separating superfine strongly magnetic minerals and the ability to produce high-grade concentrates with high recovery. They are ideal replacements for conventional drum magnetic separators, especially for treating superfine particles.

Jan 1, 2009

By J W Shields

The aim of this paper is to present a concept or model regarding a particular geological environment where gold orebodies occur in the Pine Creek Geosyncline and indeed in many other pans of the world. The name GIGIACS (an acronym for Gold In Greywacke In Anticlinal CrestS) is proposed to label this concept or model. The name Saddle Reefs (which has been in use for many years) is used for gold-bearing quartz veins which often occur in conjunction with Gigiacs. Simple patterns formed by this type of mineralisation at the surface due to different configurations are illustrated. Some examples of Gigiacs and associated saddle reefs are presented from the Pine Creek Geosyncline together with examples from other parts of the world. This concept has been used successfully as an exploration tool and five examples are given. The terms Gicsiacs (for Gold In Carbonaceous Shale In Anticlinal CrestS) and Giliacs (for Gold In Limestone In Anticlinal CrestS) are also used.

Jan 1, 1994

Six simulations by the Mpnte Carlo method employing both classical and geostatistical techniques are presented for the determination of the probability distribution of the in situ value of a coal seam. To avoid the problem of qualitative estimation of parameter variability in the calculation of an arbitrary seam value, only data values from borehole information were used to quantify the variation in four coai seam parameters.The method which is suggested as being the most appropriate is a particular geostatistical approach that employs the best linear unbiased estimate and the error of estimation for a number of two dimensional blocks. The results indicate that the variance of the coal seam unit value may be much higher than that indicated by the classical approach because of the spatial variability that is properly incorporated in the geostatistical approach.The model used in the Monte Carlo simulation to determine the economic value of a coal seam can be extended to incorporate all those parameters which are necessary for a true estimation of the probability distribution of the coal seam value. A time value concept for discounting can also be incorporated to optimize the economic return of a coal mining project.

Jan 1, 1983

By X T. Nguyen

Western AustraliaÆs Mining Act 1978 was amended in 2010 to provide for the requirement of a mine closure plan to be submitted to the Department of Mines and Petroleum (DMP) for approval, as part of a mining proposal application. The mine closure plan must be prepared in accordance with approved guidelines. Guidelines for mine closure plans were developed to assist the mining industry in Western Australia to plan and implement effective closure of mines. The guidelines focus on the application of integrated mine closure principles and industry best practice information on mine closure. This, includes stakeholder consultation, risk based approach, data collection and monitoring, development of completion criteria and financial provision.Due to the potential high level of public interest in the guidelines, extensive consultation with stakeholders was conducted. The purpose of this paper is to share experiences from the consultation process.CITATION:Nguyen, X T, 2012. Mine closure guidelines for Western Australia and consultation process, in Proceedings Life-of-Mine 2012 , pp 43-46 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012