Search Documents

By R Stefansen, T Wisdom, A Nicholson, K Rahal

The challenges of increasingly scarce water resources and the risk of dam failures has seen the mining industry turn to sustainable tailings management solutions such as dewatering and dry stacking. Filtering tailings has been seen in the past as a cost-prohibitive process for larger throughput mines. However, as larger pressure filters are developed, the economic case for filtered tailings has gained traction.Focus has largely been placed on the correct design and operation of the filters. It is critical, however, that the material handling portion of the disposal system is also properly designed and operated. Thorough testing at laboratory and pilot scale to determine the conveying properties of the filtered material needs to be conducted. This testing will insure the material handling system meets the important availability needs of the mine even during periods of variability in the upstream processes and mine plan.The control system must also be robust and flexible in design to compensate for this upstream process variability. The control system needs to allow for different flowsheets including straight filtered tails as well as EcoTails™, a low-energy solution for co-mingling waste rock and filter cake.This paper will present case studies of different material handling solutions, the testing required for them and the lessons learned from each.CITATION:Rahal, K, Nicholson, A, Stefansen, R and Wisdom, T, 2018. Material handling testing and control system requirements for dry stack tailings, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 361–368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By B M. Washington, R R. Lovel, G J. Sparrow, M J. Fisher-White

"Work in CSIRO with several Australian ores has shown that?by heating a high-phosphorus goethitic iron ore and then leaching with caustic or acid, the phosphorus levels in the ore can be lowered to a commercially acceptable value of around 0.08 weight per cent phosphorus (P). With increasing heating temperatures up to 1300¦C, the extent of phosphorus removal increased. This is considered to be associated with mineralogical changes in the iron oxide phases in the ore during the heating.Little phosphorus was removed from four high-phosphorus goethitic iron ores containing 0.12 - 0.16 weight per cent P in leaches with boiling water. However, leaches with sulfuric acid removed ten to 20 weight per cent of the phosphorus and leaching with sodium hydroxide removed even more phosphorus to produce leach products containing between 0.08 and 0.12 weight per cent P from three of the ores.After heating at 300¦C, leaches at a low pulp density of 0.5 weight per cent solids with 1 - 5 M NaOH and 0.1 - 1 M H2SO4 gave leach products with 0.06 - 0.09 weight per cent P. The lixiviant concentration required and extent of phosphorus removal depended on the ore. At a higher pulp density of 25 weight per cent solids, leach residues with between 0.07 - 0.14 weight per cent P were obtained.More phosphorus was removed from ores heated at 900¦C. Leaches at both the low and high pulp densities, with 1 - 5 M NaOH and 0.1 - 1 M H2SO4, gave leach products with 0.05 - 0.09 weight per cent P. However, the lowest phosphorus levels were obtained after heating the ores at 1200 or 1300¦C and leaching with 1 M NaOH or 0.1 M H2SO4. Leach residues with 0.02 - 0.06 weight per cent P were obtained, even from leaches at the higher pulp density of 25 weight per cent solids. Leaching tests on heated samples under heap leaching conditions at ambient temperatures have shown that phosphorus levels can be reduced to similar levels to that achieved in an agitation leach within ten days.CITATION:Fisher-White, M J, Lovel, R R, Sparrow, G J and Washington, B M, 2013. Effect of temperature on removal of phosphorus from Australian Goethitic iron ores, in Proceedings Iron Ore 2013, pp 373-380 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By T Goswami, M Edmondson

Henry Walker Eltin (HWE) are the mining contractors for Gloucester Coal at Stratford mine, which is in an environmentally sensitive area in the Avon Valley, NSW, Australia. Normal blasting at Stratford is done in a æstand upÆ or æbox cutÆ mode to suit the truck and shovel operations. Recently an opportunity of doing a throw blast became available when part of a ramp had to be blasted to accommodate changes to the pit design while not damaging the remainder of the ramp. The objective was to maximise throw into the void in order to minimise excavation costs by reducing the amount of overburden to be moved by the excavation fleet. It was necessary that the best result be achieved while staying within the vibration and airblast limits at a neighbouring property and nearby township. Both objectives were achieved through the application of OricaÆs knowledge of blast design, modelling and i-konTM electronic detonators. The i-kon system was used because of its known benefits in cast blasting and environmental control. The i-kon system provides the blaster with much greater accuracy, control and the flexibility to tailor blast designs. It has been found previously to enhance blast throw and provide cleaner high walls (Brent, 2002). The blast was a success, producing a muckpile with a high degree of looseness and consistent fragmentation, with an average throw to final spoil position of 37.5 per cent. This was achieved without any environmental exceedance. In addition, high speed filming showed that the coal edge had remained largely in place, indicating minimal coal loss. The results exceeded the expectations of HWE Stratford and the overall cost savings to HWE Stratford from this blast were recognised to be substantial. Further throw blasting opportunities at Stratford have been followed using the i-kon system to maximise benefits.

Jan 1, 2003

By R G. Reddy

The complexity in treating environmentally harmful impurities such as As, Sb, Bi from the base metal matte or metal in the smelting stage are responsible for the high cost of the refining process. The impurity capacities (such as arsenic, antimony and bismuth) of slags were calculated a priori using Reddy-Blander (RB) model. The capacity predictions were for a wide range of matte and slag compositions in copper smelting conditions. The calculated impurities capacities and impurity distribution ratios results are in good agreement with the available experimental and industrial slags data. The a priori knowledge of impurities is useful for reduction of energy consumption and enhanced environmental control in the current and future non-ferrous metal processes.

Aug 21, 2024

By Li N, Grimsey E. J

A technique has been developed for the fast measurement of the liquidus temperature of molten salt systems. The method employs a type K thermocouple embedded within the centre of a copper cylinder. The cylinder is immersed into the molten salt bath and the resultant heating curve is recorded using a PC-based data logging system. Upon immersion of the cylinder into the bath, a layer of salt freezes from the melt onto the surface. When this layer remelts during heating, the shape of the heating curve exhibits a change. The onset of this change can be detected by numerical differentiation of the heating curve, and the temperature at the onset represents an estimate of the liquidus of the melt. This work describes the technique and its application to the measurement of liquidus temperatures of MgC12 - NaCl and BaC12 - NaCl salt mixtures, in addition to a number of solidus temperatures.

Jan 1, 1996

Ore textures in Australian BIF-derived ores are quite complex and have formed the basis for ore genesis models, which includes hypogene upgrading or supergene upgrading then regional metamorphism for the microplaty hematite ores and supergene upgrading for the martite-goethite ores. Despite a high level of ore texture knowledge, little is known about the spatial distribution of ore textures within deposits or their relationship to downstream processing. This paper describes a new iron ore texture classification system to better understand the vertical textural zonation characteristics of Australian BIF-derived deposits, the interpreted role of recent supergene upgrading processes on modifying primary ore textures and their implications for downstream mineral processing. The iron ore textural classification scheme presented uses textural groupings defined on the basis of similarities in mineralogy, ore texture, porosity, mineral associations and hardness. The scheme is non-genetic and has been successfully applied to deposits in the Pilbara, Yilgarn and Gawler cratons. The main ore texture groups include dense martite/hematite, microplaty hematite, microplaty hematite-goethite, martite-goethite, goethite-martite and goethite-rich. Each group can be further subdivided into physically hard to softer subcategories. The ore textural groups can be divided into those interpreted to be associated with primary replacement of BIF and secondary textures resulting from more recent modification by near-surface hydration or dehydration processes. A schematic vertical section through BIF-derived deposits consists (from surface) of detritals underlain by a carapace, both of which may have been eroded, followed by a hydrated zone with replacement of primary ore martite and microplaty hematite by vitreous goethite. The hydrated zone is underlain by 0.2 - 6 m thick zones of intense dehydration and textural infilling of porosity with hematite and hydrohematite. Immediately below the dehydration zone is a strong zone of leaching, where more porous and friable ore textures occur, followed underneath by a gradational contact with primary ore. Secondary supergene processes can impact on beneficiation with hydration and leaching resulting in more difficult density separations at the concentrator stage due to reductions in density differences between ore and gangue and loss of heavy media into pores. Supergene modification of primary BIF-derived ore textures can substantially change lump metallurgical properties, with hydration and dehydration favourably increasing lump yield but reducing resistance to thermal shock whilst leaching will give the opposing outcome. The lump properties of ore textural groups appear to be relatively consistent within and between the iron ore deposits examined.

Jan 1, 2002

By G Barla

In Europe, a major interest in the infrastructure and tunnelling fields is in the new crossings of Alps in the form of base tunnels, which are important components of the high-speed (for passengers)/high-capacity (for freight) Trans European railway corridors. These tunnels cross the mountain belt at the elevation of the main cities and basins located all around the Alps and are longer (up to 57 km) and deeper (up to 2500 m) than all tunnels constructed in the centuries before. The excavation of the first Alpine railway and road traffi c tunnels could in general be carried out successfully by conventional excavation methods. With the great lengths of the new base tunnels, mechanised excavation by using tunnel boring machines (TBMs) is imperative as it contributes significantly to savings in construction time and costs. Questions are however posed on the adoption of such a systematic tunnel construction method given the severe ground conditions which are some time anticipated along the tunnel alignment, with possible major geological hazards such as water inflow in heterogeneous fractured or karstifi ed rock masses, stress-induced tensile failure of hard rocks, and plastic shear failure and squeezing of weak rocks, etc. This lecture is to briefly review the current state-of-the-art in the understanding and modelling of two such critical hazards as spalling/bursting and squeezing ground behaviour. With the present interest in the design of mechanised tunnelling with TBMs in such conditions, the complex interaction between the rock mass, the tunnel machine and its system components, and the tunnel support is studied in detail by numerical modelling. The research and development efforts presently underway with the intention to provide the designer with a novel three-dimensional (3D) simulator of mechanised tunnel excavation are presented. Case examples are discussed with reference to the Lyon-Turin Base Tunnel design.

Mar 8, 2011

The care necessary to ensure a reliable estimate of average value from the individual values of a series of bore holes sunk in any alluvial deposit containing coarse gold was well exemplified in checking over the mining returns from a previously bored deposit in Central Otago, N.Z. While the working returns are always liable to vary considerably from bore values in any particular sub-section of an area, still, over any considerable area, the two must check within small limits, if profits are to be calculated and capital raised on the average value given by boring.The present figures have probably more value than those from, dredge returns since accurate measurements are difficult to obtain in irregular water-filled dredge paddocks, whereas in the case under review the paddock walls stood almost perpendicular, and, as the measurements were taken and checked in the empty rectangular excavation, the yardage estimate may be taken as substantially exact.NATURE OF DEPOSITThe area consists of a narrow valley deposit of fluvio-glacial origin, the original deposit having been eroded and the gold reconcentrated by post glacial rivers. The wash is between 80 and 90 ft. deep, and is formed in two distinct layers:(i.) The top layer from surface to 70 ft. or 80 ft. consists of about equal quantities of gravel mixed with glacial drift, and a small amount of clay. The gravel is typical discoid glacial stone of a maximum size of about 4 in. diam. by 1 in. thick, and consists of soft micaceous schist and laminated slate. This upper layer of wash contains no coarse gold whatever, and very little fine; indeed, in mining, the top 30 ft. is discarded without being passed over the boxes.(ii.) The lower layer of wash to bedrock is similar to the upper, except iihat it contains about 10% of larger discoid stone up to 12 in. diam. by It in. thick; 90% of the gold is concentrated in this bottom layer.

Jan 1, 1929

For small particles of niekel flotation eoncentrate (av. size 50 pm) the predominant heat transfer mechanism under suspension smelting conditions, prior to ignition, is conduction from the gas and not radiation from nearby hot bodies. Results of laboratory tests using gas temperatures 380-700°C and furnace wall temperatures 380-1100°C were in accord with heat transfer theory. In practieal flash smelters earlier ignition, and hence better utilization of the space in the shaft, would result from introduetion at the top of the shaft of gases hotter than the ignition temperature of 500-600°C.

Jan 1, 1979

By T Bednarz

The present work proposes a distributed collaborative immersive virtual reality framework for prospective applications in the mining industry. A human-centered approach is described, with people being placed in the central position and surrounded by tasks that are to be carried out. Those tasks can be then achieved through synchronous or asynchronous communication, interactions using properly constructed user interfaces, virtual and/or augmented realities and computer vision. Several examples of such arrangements are presented. One of the applications facilitates an e-learning experience by providing a very familiar object – a book – as a target for users to interact with. Importantly, this system has the potential to provide an ‘enhanced’ teaching medium, as humans tend to remember events/situations better when they experience those events in person, when the immersive factor is involved. The immersive virtual reality environment enables a user to interact physically with various 3D objects and experience behaviours, which in turn reinforces the idea that doing leads to learning. This prototype system can be implemented as an efficient and cost effective e-learning and training platform for different engineering domains. At another level, the same technology can be used in the tele-operation of mining equipment for the future mine.

Nov 22, 2011

Using a Jarrell-Ash "Compact" direct reading spectrometer, analyses were made of a wide variety of rocks ranging from acidic to ultrabasic types. Statistical evaluation suggests that accuracies comparable with the values obtained by the rapid chemical methods used by the United States Geological Survey will be obtained.The spectrographic method involves fusion of the rock with lithium tetraborate, strontium being incorporated in the flux as the internal standard. The resulting bead is ground with graphite and pressed into a pellet. The counts obtained on two standard pellets are used to correct for instrumental drift.Background readings are made at 4109 Å and corrections for background are made to all lines. Corrections for matrix interferences, both by chemical suppression and optical enhancement, are made. The three corrections of drift, background, and matrix are incorporated into one general expression which has been programmed on magnetic cards, each element requiring a separate card. The cards are placed individually into a desk top computer (an Olivetti Programma 101), which enables true counts to be calculated from the "readout" counts, and the element concentration is then obtained from computer-printed tables by referring to the appropriate value of true counts versus concentration. These tables were prepared by making a polynomial regression analysis of the spectrographic results from 50 standard and analysed samples, a curve of best fit being chosen for each element.The regression coefficients, usually of a fourth or fifth degree equation, together with other relevant data, were fed into a large computer, programmed to print out tables of concentration versus true counts. This technique enables the results obtained to be based on mathematically-derived values rather than on hand-drawn calibration graphs, giving greater inherent accuracy. The technique has been shown to give results of good accuracy and acceptable precision suitable for many geological and geochemical exploration programmes involving the analysis of many rock samples of different types.

Jan 1, 1969

By H Wang, D Wang

Mine dust is the most serious occupation hazard in coalmines. And many coal workers suffer from pneumoconiosis because of long-term inhalation of respirable dust. Reducing the dust concentration of workplaces by effective technical means is an important way to prevent coal worker’s pneumoconiosis (CWP). In order to overcome deficiencies in existing dust control technology for underground mining, especially the disadvantage of water spray technology mounted on roadheaders or continuous miners, the authors developed an integrated dust suppression technology utilising foam for fully mechanised heading faces. This paper presents an overview of the principles, materials, equipment and application of this technology. Among these, a jet type foaming device and a green foaming agent were developed, which can realise the goal of efficient preparation of foam. In addition, an arc fan nozzle used for foam spraying was invented, which can effectively cover and enwrap the dust produced by the roadheader at the cutting point and achieve the goal of efficient utilisation of foam. This dust suppression application of the proposed foam technology was investigated on fully mechanised heading faces. The results show that the dust concentration was cut down significantly with a dust suppression efficiency of greater than 85 per cent, an increase of over 30 percentage points compared to the water spray system. This study demonstrates that this foam technology can play an important role in dust suppression on fully mechanised heading faces, which provides an important method to improve the working environment and protect coal workers’ health.CITATION:Wang, D and Wang, H, 2015. Technology of dust suppression by foam for fully mechanised heading face, in Proceedings The Australian Mine Ventilation Conference, pp 177–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

A number of terrane reconstructions conflict with global plate histories or with data from adjacent regional studies. Paleogeographic maps have ignored terranes thus are over-simplified. This paper represents an attempt to "marry" Mesozoic global plate reconstructions and terrane analysis to produce examples of a "third generation" of global plate tectonic maps. The best approach to global terrane analysis involves intercomparison of all regional data and the evolving global model. Data conflicts within and between terranes and regions must be resolved by a system of relative data reliability "weighting." The most reliable and useful data are those which constrain "departure" (rift) and "arrival" (collision) times. Certain ad hoc decisions aid in the analysis (e.g. only one net vector allowed per plate). The maps that follow summarize Early Mesozoic global tectonic history at three critical junctures: 240 MA (Triassic); 180 MA (Jurassic); and 120 MA (Cretaceous). Due to space limitations, maps drawn at 20 m.y. intervals appear elsewhere. A preliminary Middle Triassic reconstruction is presented in Figure 1. Major plates and continental blocks are labeled; smaller blocks are marked with abbreviations. Examination of Figure 1 indicates the necessity of modeling Triassic tectonics with at least 68 blocks. Spalling- off of microcontinental slivers from Gondwanaland is active some 70 m.y. before the actual breakup of the supercontinent. In the SW sector of the Pacific, the Australian margins were embroidered with several terranes (e.g. Sumba) which eventually rifted away and crossed Tethys. The NW sector at this time included 10 microcontinental chips forming a huge archipelago along the Asian margin. All blocks inboard of Indochina collided by latest Triassic. Terranes of the NE sector include several (e.g. Arctic Alaska) along the North American margin, and at least six large blocks (e.g. Stikinia) drifting SE with the Farallon Plate. The SE sector

Jan 1, 1987

Theories of ore genesis. have both practical and philosophical application-practical in that they influence our search for new ore bodies; philosophical in that they provide a test for our theories of petrogenesis-and our ingenuity.For example, the theory of granitization requires an explanation of ore genesis compatible with the general concepts of granitization.Our understanding of some processes of ore formation, such as supergene enrichment, or the formation of residual lateritic iron ores, is so complete as to permit of nq controversy.For other ores, like the oolitic iron ores of England and France, and elsewhere, or the segregations of chromite or ilmenite in basic igneous rocks, the broad principles are generally agreed on; dispute is limited to details of process.But for a wide range of ore deposits there is no such agreement. Completely incompatible hypotheses are advanced to explain' identical facts, and we have difficulty in finding new facts or criteria that will distinguish unambiguously between them.In thinking about such ores, a co:n;venient starting point is provided by Schneiderhohn's (1953) fourfold division of ore deposits:1. The secondary hydrothermal ore deposits occurring in Mesozoic-Neozoic cover strata of Europe.2. The "regenerated" younger ore deposits in Alpine type mountain chains.3. Post-Cambrian primary hydrothermal ore deposits.4. Ore deposits of the PreCambrian shields.To these we may add a fifth group:5. Stratigraphically controlled sulphide deposits.

Jan 1, 1956

The use of pipeline-c to carry crude'oil and petroleum pro-ducts is a reliable and economic*Way to transport large quantities of oil. The length and size of these pipelines have continued to grow throughout the world as the demand for petroleum has in-creased and as the price of other transportation-methods has risen. At the present time pipelines 'can move a barrel of oil a distance of 100 miles at an average cost of ,80.06 U.S. dollars.The major elements in pipeline design are discussed. Methods of calculating pressure drop and horsepower requirements are pre-sented. These are variations of standard equations.in which the elements of each equation are expressed in terms common to the petroleum industry. Major equipment is discussed., particularlyas it relates to operation and economics.Cost data are presented to aid in preliminary economic ana-lysis. Curves illustrate the cost of oil transportation at flow rates between 10,000 and 500,000 barrels per day and permit the selection of pipe diameter-which will result in minimum operating costs.

Jan 1, 1962

The underground coal mining industry in Australia has, in the last 30 years, undergone a revolution in production methods, techniques and results probably unparalleled elsewhere in the world. It can lay claim not only to leading the fight against pneumoconiosis and setting high safety standards generally, but has at the same time recorded comparatively high rates of increase in output per man shift. The latter has been achieved as a result of progressively matching the latest in production and underground transportation equipment with significant changes in seam development and extraction techniques and the introduction of stress-relieving extraction methods unique to the world scene. However, the seam recovery factor is still too low. Apart from the overall objectives of maximising production and commercial returns with the greatest safety, there must be a concentration towards maximising seam recovery, particularly in high seams. The search will continue for systems which are more completely continuous mining operations than the present stop-go operations, with longwall having long term potential in this regard, but as yet not sufficiently developed to engender confidence for its more general use. Techniques developed in the last 10 years make the development and extraction of deeper seams, perhaps to 2500 feet or more, feasible with continuous miners as well as longwall. The future will see a greater use of continuous shifts at mines, larger mines with more sophisticated management organisation, extensible belts at the face, better systems of immediate roof support at the face, remote operation of face equipment, greater use of roof bolts and the longer roof cables. With commercial confidence in coal mining now virtually assured to at least the turn of the century, the stage is set for heavy capital development in the industry which will undoubtedly include major research into the whole area of mining methods and equipment. We must ensure that our contribution to such research equitably matches other coal producing countries.

Jan 1, 1975

By K C. Corin, C T. O’Connor

In recent years it has been shown that the concept of using partial molar excess Gibbs energy (G̅ex) to explain the behaviour of collectors in the recovery of minerals can be usefully applied to explain flotation performance. Fundamentally this is because hydrophobicity of a mineral particle on which a collector is adsorbed may be strongly related to the fact that the alkyl chain associated with the collector behaves in the same way as any hydrocarbon would in an aqueous medium. This hydrocarbon-water system represents a classical non-ideal mixture, and such mixtures are quantified thermodynamically by determining the activity coefficient of the hydrocarbon moiety of the collector and hence its G̅ex in the mixture. It has been shown that G̅ex is a more rigorous indicator of the contributions of various alkyl groups of a collector than HLB (Corin and O’Connor, 2014) and was also able to explain aspects of froth behaviour (Harris and O’Connor, 2017) and hydrophobicity (O’Connor, 2021). The present paper is aimed at extending the above concepts in two different ways. Firstly, a study is undertaken of a range of results previously reported in which various reagents containing different alkyl groups were analysed in terms of their effect on contact angle and their performance as flotation reagents in terms of recovery. These results sustain the previous observations that there is a robust positive relationship between hydrophobicity as indicated by flotation recovery and contact angle and G̅ex of the alkyl group associated with the collector. Secondly, on the basis of the observation that increases in G̅ex are indicative of increases in the hydrophobicity of the mineral particle-collector aggregate, a study was undertaken to examine the effect of ions typical of electrolytes in water as well as the effect of the presence of alcohols and of pH on G̅ex of the collector alkyl group. In the former two instances the absence of any correlation between G̅ex and recoveries supported the proposition of the respective authors of these studies that the major effect of these electrolytes and added alcohols may be on particle–bubble attachment rather than on the hydrophobicity of the mineral/collector in the aqueous system. On the other hand, the effect of pH on G̅ex correlated reasonably well with changes reported in the literature on the effect of pH on recovery and contact angle.

Aug 24, 2022

By J B. Taylor

Geographic Information Systems (GIS) are being increasingly used by the mineral exploration industry in the search for new ore deposits. A mineral exploration GIS links geological and geophysical data by virtue of their geographic location in a digital map setting. Geological and geophysical data are categorised into a number of themes or layers within a mineral exploration GIS. These layers may include polygonal information such as rock type and tenements, line information such as faults and fold axes, point information such as mines and mineral occurences, and images such as gridded geochemistry and aeromagnetics. A mineral exploration GIS is a powerful tool to help the explorationist comprehend the spatial associations and interrelationships of his/her data. These spatial associations can be integrated with a mineral genesis model, to create a mineral prospectivity map to more effectively target exploration. Arguably a competent geologist who has a good understanding of the genesis of the local ore deposit types and knows their local geology backwards could intuitively derive a mineral prospectivity map. However, in an era of rapid data accumulation from many different disciplines, the ability to assimilate and understand is a huge task for any individual. A mineral exploration GIS enables the explorationist to spend more time analysing data and testing ideas, rather than finding and manipulating data into compatible formats.

Jan 1, 1994

By C D. Strickland

Western Australia (WA) has been a significant world producer of titanium minerals (rutile, ilmenite and leucoxene) and zircon for over 55 years. In 2010, despite global difficulties, WA accounted for 12 per cent of world production for zircon, ten per cent for ilmenite, and eight per cent for rutile. With downstream processing, titanium minerals (ilmenite, rutile, leucoxene) and zircon exports for 2010 were valued at $511 M (Department of Mines and Petroleum, 2010).Production is dominated by two areas of the Perth Basin, namely the Eneabba and the Bunbury-Capel regions, which are located 240 km north and 200 km south of Perth respectively. Mineralisation is within Cenozoic beach or near shore dune deposits at three broad altitudes related to the present coastline, and two older higher sea-level still-stands. The titanium-zircon minerals presumably were derived from the underlying Mesozoic sediments of the Perth Basin. Contrary to expectations, age dating suggests that the ultimate source of most of this mineralisation was not the adjacent Yilgarn Craton. With the cooperation of industry, the Geological Survey of Western Australia has mapped all known significant titanium-zircon mineralisation within the Perth Basin. This mapping has identified ‘strategic mineral resource protection areas’ that should be set aside for future mining, ‘sterilised’ and ‘mined’ areas that generally do not restrict land use options, and ‘possible strategic resource areas’ which have exploration potential for hosting titanium-zircon mineral deposits.The Perth Basin is currently undergoing rapid residential and industrial development. By informing all stakeholders of the locations of potential mining areas, the titanium-zircon mapping has the ability to reduce future land use conflicts, and facilitate sequential land use planning. Appropriate planning measures are being implemented to ensure that the Western Australia’s titanium-zircon minerals industry remains strong and viable in the future.

Oct 5, 2011

Few, if any, reliable thermodynamic data are available for the activity of tin oxide in slags. In this work, the activity of the oxide in silica saturated iron silicate slags has been measured at 1573 K using the equilibrium Sn (alloy) + Y2O2-SnO (slag).Slag and a Ag-Sn alloy were sealed in a zirconium oxide crucible to prevent the escape of volatile tin oxide, and the oxygen pressure at equilibrium measured in situ using the zirconium oxide as a solid electrolyte. Activity of tin was calculated from known data for the Ag-Sn system and activity of tin oxide calculated from free energy data. The results have been extrapolated to predict the industrially important distribution of tin and iron between Fe-Sn alloy and iron silicate based slags.

Jan 1, 1983