Search Documents

The mmmg operations carried out by North Broken Hill Limited, necessitate the use of four shafts for the haulage of ore, men, and supplies. These are:-1. Blackwood's Shaft.-British Section, which has 100 feet intervals between levels to the bottom 800 feet level plat;2. Thompson's Shaft.-British Section, which has 100 feet intervals between levels to the bottom 1400 feet level plat;3. No. 1 Shaft.-With intervals between levels:(a) 100 feet to the 800 feet level,(b) 150 feet from 800 feet level to the 1700 feet level;4. No. {2 Shaft.-2770 feet from collar to bottom plat, with intervals between levels: (a) 100 feet to 800 feet level, (b) 150 feet from 800 feet level to the 2600 feet level. (c) 170 feet from 2600 feet level to the 2770 feet level.All shafts have two cage compartments, and the No. 2 Shaft a skip installation in addition.For the control of hoisting operations an electric signalling system is installed on each shaft, and is supplemented by a counterbalanced rope pull ("Knocker line") operating a surface gong. The latter system is shown diagrammatically in Fig. 1.Two sets of electrical equipment are used per shaft. The first, shown in Fig. 2, is that operated by the braceman or...

Jan 1, 1940

By Yoshii Y

Many kinds of shield machines are being driven in the soft ground of Tokyo metropolitan area. Tunnel alignments for underground power transmission lines are generally planned to pass under public roads where facilities, especially life-line facilities, are densely located. Therefore, it is frequently required to drive the shield machines along very sharply curving routes. This paper reports on the performance of the new shield machine - the Sharp Curve Excavation Shield Machine - developed by Tokyo Electric Power Co., Inc., which can freely drive along a much sharper curve than conventional machines. Some of features of the developed devices of this machine are, maximum flexing angle of 6.5 degree in all deirection at the middle of shield body, maximum bending angle of 3.5 degree in all direction at the cutter disc, and so on. This shield machine can there- fore drive along curve of minimum radius 15m. The machine was confidently applied to the const- ruction of tunnel in soft clay strata at N values 2 to 5. Outer diameter 3.7m. Length 202m. Horizontal curve; radius 15m, length 20m x 2. Vertical curve; radius 30 m, inclined driven up 29%. The behaviors of the shield machine, segments and surrounding ground were monitored during construction for safety and efficiency check of this machine.

Jan 1, 1987

By Mills J. C

Concentration ranges are presented for 15 trace elements not previously reported in Australian bituminous coals. The results were obtained by instrumental neutron activation analysis, which has sufficiently high sensitivity to enable determination of many elements directly in coal at concentrations less than a few µg/g. The ranges found in Australian coal are similar to the ranges reported in North American bituminous coals.

Jan 1, 1983

Several coal preparation plants are presently "automated" to the extent of automatic sequencing and interlocking via digital means, together with closed loop control on various level and density circuits. This paper will explore the potential for second generation automation utilizing on-stream ash analysers and other measuring elements so as to optimize the total metallurgical process. This would enable maxim-ization of recovery, improved product homogeneity and minimum reagent consumption.

Jan 1, 1985

By Quadrio J. S, MacHunter A. M W

The initial development fl6tation testwork on Mt. Windarra op was completed on composited drill core intersections at the.Australian Mineral Development Laboratory. An exploratory winze provided samples, from the 130 M. level of the Mt. Windarra mine, for pilot plant and bench development tests. A limited test programme was initiated on the South Windarra drill core composites. Detailed mineralogy has been completed on selected samples from both ore deposits.

Jan 1, 1973

By Goodheart B

The Australian Mineral Sands Industry has expanded from the initial export of mixed concentrates in the 1930s, through various development stages, to its current position as a leading world producer of individual mineral products and some further processed products. Opportunities for downstream processing of the separated minerals and locating such developments in Western Australia are reviewed, along with the role of the Western Australian Government in assisting resource development projects.

Jan 1, 1986

By Brant BA, Lewandowski R, Trendle M, Haughton D

There is a vast amount of geotechnical data, which can be obtained during exploration programs at new and existing mine sites. Additional information on the performance of the in-situ rock mass can be obtained from bore cores, which are usually only geologically logged and then stored. A computer based data management system for storage and retrieval of geotechnical data has been developed to access and manipulate such data.

Jan 1, 1983

By Collins AR, Meares RMD, Graham JM

Exploration programs for both alluvial (placer) and hardrock platinum group metal deposits are being conducted in Papua New Guinea by a joint venture between Degussa AG and Pancontinental Mining Limited. Prospective areas were defined on the basis of ultramafic/ophiolitic source rocks shedding detrital platinoid grains. Field sampling techniques including churn drilling, together with appropriate laboratory analytical and mineralogical techniques, were developed and are contributing to the success of the exploration programs.

Jan 1, 1987

Recent operating experience from West Australian open pit gold mines has shown that geotechnical input into initial design is rare. As a result, ground stability is poor - almost half the pits designed in this way suffer major failure.West Australian experience shows that geotechnical studies for individual mines are site specific, and therefore empirical experience cannot be transported from site to site. Geotechnical studies performed prior to design have resulted in significantly improved pit stability.

Jan 1, 1990

The Granites Gold Mine has far exceeded the design capacity of 300,000 tonne per annum during its first sixteen months of operation. The presence of considerable free coarse gold has made it imperative that the gravity section operate at maximum efficiency. The inadequacy of acid digest- ing facilities and trying climatic conditions prompted management to initi- ate investigations into the use of Intensive Cyanidation as an alternative method for upgrading gravity concentrates prior to smelting.

Jan 1, 1988

By M Nehring, M Kizil, P Knights

Mining and beneficiation can be described as sequential processes of separation of valuable minerals from waste. There is a great deal of interest in how the industry can be more effective – and efficient – with these processes. In particular, many mining companies are looking towards digital technologies to improve precision mining practices; that is, the targeted identification and separation of valuable ore from waste during the mining process. Greater precision will help unlock the value in many complex orebodies that are currently considered Tier 2 or 3 deposits. CITATION: Knights, P, Kizil, M and Nehring, M, 2018. Selection of precision surface mining methods for complex metalliferous orebodies, in Proceedings Complex Orebodies Conference 2018, pp 31–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

This paper describes the principle of cut-and-break rock excavation, in which rock is first undercut, and the undercut material is subsequently broken free by a wedging action. The current work on cut-and-break using the large rock cutting test rig at the Centre for Mining Technology and Equipment (CMTE) is outlined, and suggestions are made as to the potential advantages of cut-and-break roadheading, particularly in excavating short tunnels in hard rock in an urban environment.

Jan 1, 1993

By Darby H. P, Vincent R. J

Sydney's Eastern Suburbs Railway from Central to Bondi Junction required the construc- tion of 10.4 km of single-track tunnel and five underground stations. Much of this work took place beneath the commercial centre of Australia's largest city. This paper discusses the general precautions taken and the specific design solutions made for such problems as support of a 15-storey building with foundations several metres above the excavation to ensure negligible differential settlement, excavation immediately below running tunnels, underpinning of multi-storey buildings, tunnelling under massive masonry retaining walls and demolition and rebuilding of part-completed structures.

Jan 1, 1981

By Singh RN, Yuejin LI

The problems experienced with longwall mining machinery motivate the development of an expert system for fault diagnosis. The techniques of knowledge representation, database, knowledge base and inference engine guide the selection of the expert systems and languages -"Turbo Prolog"- as exemplified in the case study of hydraulic support. The aim is to hasten future development of a fault diagnosis system and the design of a system to locate and determine the causes of failure of longwall machinery. The system would use its stored case history and other information to make fault diagnoses and suggest appropriate remedies. Consequently down-time would be reduced and production and profitability should increase.

Jan 1, 1991

By Hutchinson IN

In order for the Australian underground coal mining industry to achieve the high productivity rates demanded of it without compromising its good safety record, improved geotechnical monitoring systems are required. One of the main problem areas affecting underground coal mining is the deterioration of previously stable roadways.CSIRO Division of Geomechanics has been working on a NERDDC funded project to develop an instrument to monitor coal mine roof deformation. The instrument which has been developed, Roof Alert, is a self contained, battery powered, intrinsically safe device. It can monitor the magnitude and rate of deformation and give multiple, variable visual alarm signals where preset levels ate exceeded.

Jan 1, 1991

The need to estimate the block size distribution of a jointed rock mass is of great importance in the design of blasting rounds to attain a pre- established fragmentation. Other Geomechanics topics, such as ,hydraulic behavior of rock-masses, as well as the determination of their strength properties, also require the accurate prediction of a rock-mass composition in terms of block size taking in due account the three dimensional interference of joints and other geologic discontinuities. In this paper, a method for computing the block size analysis of a jointed rock mass is described, using as input the common geologic data (dip and strike) of fracture planes existing in a rock bench prior to blasting.

Jan 1, 1977

By Cocker J, Urosevic M

Seismic methods have become common for the detection of low-throw faults ahead of underground coal mining. Surface seismic methods cannot theoretically be used where dykes occur, because seismic waves transmit from the surface down to the seams, and reflect back to the surface. Consequently, where sub-vertical structure such as dykes occurs, the surface seismic method fails.The ability of seismic methods to image dykes depends on the geometry used, the dyke thickness and the seismic wave propagation mode in relation to dyke composition and internal structure. Surface seismic methods find it difficult to distinguish between faults/fractures and very thin dykes (1-2m in thickness) when the dyke's thickness is less than the seismic wavelength. Consequently, borehole seismic methods have to be used to detect the presence of such thin dykes.

Jan 1, 1998

By Mckenzie CK, Leach KR, Bateman KW

Modelling of industrial coal flotation based on data collected in several Central Queensland flotation plants and supplemented by laboratory data is discussed. The model is kinetic in form and provides the basis of an automatic control system. The important features of the model are, 1. a distribution of flotation rates for each species of particles corresponding to the range of particle sizes, 2. a physical restriction on the removal rate of solids in cells where froth 'overloading' occurs. In this condition the removal rate of solids is proportional to the removal rate of water, 3. enhanced particle floatability due to increasing collector addition where froth overloading does not occur, 4. a second mechanism of recovery of all particles by mechanical associ- ation with water. This mechanism is particularly important in the recovery of fine high-ash species.

Jan 1, 1978

By Jena P. K

Smaller deposits of high grade chalcopyrite or the concentrates of low grade and complex copper bearing ores, can be subjected to extraction processes other than smelting and converting. Low temperature chlorination and segregation processes are among those mentioned in the literature. In the present work, extraction of copper from a Brazilian chalcopyrite concentrate by slurry chlorination with chlorine gas at room temperature, dry chlorination by chlorine gas in the temperature range of 350 to 450¦C and segregation roasting of the calcined concentrate in the temperature range of 650 to 800¦C have been carried out. The effect of several experimental variables on the extraction of copper has been discussed in all these cases. Under optimum experimental conditions, 100 per cent Cu extraction was possible by either slurry or dry chlorination processes and around 86 per cent Cu by segregation roasting. For all the three cases, possible methods have been suggested to trial the studies on a pilot scale to assess their technoeconomic viability.

Jan 1, 1992

By R G. Barker

This paper reviews the annual status of the New Zealand mining industry (metallic minerals and coal) including key aspects such as mineral production, mineral exploration expenditure, commodity price trends, key industry players, market activity and other significant commercial factors.   Strong commodity prices during 2006 have been underpinned by a number of key factors including US dollar weakness and emerging market demand, particularly from countries such as China and India. In real terms commodity prices have recovered significantly since 2002 and are currently at 20-year highs.   New Zealand exploration spending on metallic minerals (predominantly gold) is at a 15 year high driven by rising global commodity prices. New Zealand gold production in 2006 was about 340,000 oz and is expected to grow in 2007 as new mines at Frasers and Globe-Progress (Oceania Gold) and Favona (Newmont) come on stream. Gold production broadly lags 10 years behind exploration spending and exploration activity over the last five years remains well below that seen in the early 1980Æs. Expenditure on coal exploration shows a similar trend with strong growth from a low base over the last five years, reaching over $11 M in 2006. Total coal production in 2006 was 5.9 Mt, an increase of 10% on 2005 with imports from Indonesia adding a further $1.1 Mt.   Newmont and Oceana Gold are by far the largest public gold mining companies operating in New Zealand, although only Oceana Gold maintains a presence on the local stock exchange. Other metals explorers with New Zealand projects include a range of public-listed Juniors (market capitalisation less than NZ$50m) domiciled largely in New Zealand, Australia and/or Canada. Capital-raising on public markets directed towards New Zealand exploration is estimated at around NZ$12 M for 2006, the bulk of this coming via Glass EarthÆs NZ$10 M IPO on the NZAX in October.   The New Zealand Coal sector is dominated by the state-owned enterprise Solid Energy with around 80% market share by production. Other domestic coal competition remains limited, and includes the L&M Group, Pike River Coal, Eastern Corporation, and New Vale (acquired by Solid Energy in 2007). Pricing parity comes mainly from imported coal and global thermal coal prices have remained strong during 2006 at around US$45-55/t, driven by continued expansion in Chinese demand. Coking coal prices have eased 16% since 2005 to around US$98/t in 2007.   Although recent increases in exploration spending suggest a renaissance in the New Zealand minerals sector, long-run trends indicate that we have simply rebounded from a low base over the last five years and much work is still to be done to stimulate further growth in the mining industry to maintain minerals production at current levels. Key industry challenges include marketing exploration opportunities to local and overseas investors, building a critical mass of NZX-listed explorers and providing an internationally competitive environment to attract further capital and expertise.

Jan 1, 2007