Search Documents

By Mutmansky J. M, Hartman H. L

Multiple operating points for mine fans are a problem that fan and mining engineers must constantly be aware of in mine/fan systems. In a single-fan system, unstable conditions can be avoided by restricting fan operation to the "normal operating range." When mine fans are operated in parallel, the situation becomes a little more complicated. Multiple operating points are more often encountered and the fan user must be aware of these multiple points to have a suitable set of operating conditions. However, for fans in parallel, the engineer can plot the combined characteristic in a relatively straightforward manner and thus can avoid conditions that would cause instability in the mine/fan system.

Jan 1, 1988

BECAUSE of the attention given in recent years to the flotation process, there is an extensive range of equipment available to any staff detailed for: the design of a flotation mill. This statement applies not only to the flotation machines, but also to equipment for crushing and grinding, elevating the pulp, dehydrating of concentrates, and the methods of driving the various equipment.Distributed through the Proceedings and Transactions of various metallurgical societies and journals there are many excellent descriptions of flotation mills, their equipment and performance.Whilst these articles describe-in many cases in detail-the equipment in the mills to which they refer, the reasons which govern the choice of each particular equipment are not usually given.

Jan 1, 1929

By Mandzic E. H

The Dome Mine of Timmins Mining company is located in South Porcupine, N.W. Ontario. The orebody being mined partially lies in the No. 3 shaft pillar. Stability analysis has been carried out to establish the influence of nearby mining on ground movement in the shaft vicinity. Mathematical modelling of shaft displacement has been done for stope layout at depths from 180-210 m and distances of 10-50 m from the shaft. Analysis indicated that ground displacement around the shaft is below 1 mm/m and one third less for cut and fill than in the case of open stope mining. The result of the investigation was later confirmed by cut and fill mining of this orebody.

Jan 1, 1986

Previous methods for the assessment of the explosive potential of gas mixtures have required the plotting of apeexplosibility diagram. These became cumbersome if a large -number of assessments of various sampling locations over a period of time wererequired. This may make the approach of a dangerous situation more difficult to predict. With the aid of a programmable calculator, a new method for the rapid assessment of the explosibility of coal mine sample gases has been developed. This method does not require that an explosibility diagram be drawn to indicate the explosive status of a gas mixture. Simple Cartesian co-ordinates representing the explosive potential of,mixtures are obtained, which may readily be plotted to show changes with time.

Jan 1, 1981

Norway, a country large in area but small in population, has put large effort in protect- ion of its inhabitants in case of war. The Civil Defence has provided shelters for more than 50% of the population. Some of these shelters are put into rock. Since rock installations give large resis- tance against weapon effects and also by advan- tage can be used for several purposes in peace- time, an interesting development has taken place the last decades. In towns and cities you will find sport halls, swimming pools, bowling and shooting ranges etc in rock, which easely can be conver- ted to civil defence shelters. Some typical installations are highlighted in the following.

Jan 1, 1987

Introduction.History of Stope Filling at Mount Isa.The Need for a Systematic Fill Programme.Reasons for Filling.Fill Materials and Tonnages.Rough Mullock Fill.Quantities Readily Available.Fill Pass Development.Stope Preparation.Drainage.Hydraulic Sand Fill.Initial Experiments with Mill Tailings.Surface Layout.Operation Procedure.Underground Pipe Lines.Life of Sand Pipes and Cones.Drainage.Old Tailings Dam Sands.Quantity of Fill Placed.Pillar Tonnages.Conclusion and Acknowledgment.INTRODUCTIONFilling practice outlined in this paper refers exclusively to the Black Star section of the mine. The stope filling necessary early in the life of the Black Rock and portions of the Rio Grande sections is not to be confused with the current filling programme.

Jan 1, 1953

By Pathan AG

This research work is concerned with an investigation of the fracture toughness of sandstone, siltstone, and coal. Tensile failure trades have been examined with three different specimen geonetries, i.e; rectangular bar, round bar (in three point bending), and diametral compression discs. The Stress intensity approach, and J-integral methods were used to evaluate fracture toughness. Results from both approaches are discussed. True crack length was determined after pre-cracking, using the compliance calibration technique. Fracture toughness results of sandstone are independent of crack length and the size of the specimen. Fracture toughness may hence be regarded as a material property for sandstone. In cxnntrast fracture toughness values for !siltstone and coal are dependent on crack Length.

Jan 1, 1986

By Koppe J. C

This study presents the procedure of mine modelling and reserve evaluation by means of statistics, computer interpolation methods and aerophotography interpretation. All data are from Carbonifera Treviso, Laura Muller City, Santa Catarina State, southernmost Brazil. From 22 bore holes and nine trenches opened in the coal seam outcrops, a data base including level references and thickness of all rock formations was created.Using this information, basic statistic analysis was carried out, showing that there are three different populations (three modal distribution). These populations defined three geological blocks with different characteristics of overburden removal and mining methodology. This mathematical approach for analysing geological data is very important for correct mine planning and complementary prospection.

Jan 1, 1993

This paper presents a new idea in field data collection for geological and scientific data. The computer keyboard has been replaced by a barcode wand driving a spreadsheet style editor. To use the full capabilities of computer hardware currently available, geotechnical and geological data can be entered and validated in the field, in a structured format, for later transfer into modem geological modelling databases. An example, using a geotechnical borehole log, explains the principles discussed. The generic nature of the Datcol system is illustrated by the application developed using the Norwegian Geotechnical Institute Rock Mass Classification system. A brief description of a modem spatial relational database is also given with particular reference to underground engineering.

Jan 1, 1993

The recent installation of top gas temperature probes in blast furnaces at Australian Iron & Steel Pty. Ltd. - Port Kembla, has provided the means for studying radial gas flow distribution in blast furnace shafts. This paper describes the top gas temperature probes and outlines their development and results of initial studies aimed at obtaining a suitable relationships between temperature profiles and furnace parameters. The effects of various combinations of burden materials have been outlined by the results reported. The use of probes has also helped to clarify the effect of casting cycles on furnace operation leading to increased emphasis on the reduction of the interval between gun-up and drill-out. Areas for future studies are also broadly Outlined.

Jan 1, 1975

By Kennewell G. J

This paper aims to present the evolution of the mining method in the Prince Lyell orebody. Initial strategy and practical experience are detailed as are the reasons for and benefits of changes to the method since 1972 when underground mining began. This section of the paper starts with ten series and concludes with 40 series which was completed in 1989/90.In addition, to update the series of papers written by various authors over the past ten years on Mount Lyell, a review of the experience in the current 50 series lift of mining will be given. As well, the basic planning guidelines are discussed for 60 series - the final lift of the Prince Lyell orebody.

Jan 1, 1992

The results of a systematic geochemical survey of rare elements are applied to elucidate genetic relations in a suite of rocks and to predict the probability of mineralization. The geology, radioactivity, major element geochemistry and classification of the main intrusives are described. The distribution of a group of rare elements, their concentration trends and the bearing these have on the emplacement sequence of the rocks are considered in some detail. The guides for exploration in the Pilanesberg that emerge are listed and some areas which substantiate predictions are described briefly. It is concluded that a study of rare element trends can make a considerable contribution as an exploration tool and for clarifying relations between the members of rock suites.

Jan 1, 1986

It would be a good thing when reviewing the challenges to be faced by the Australian gold industry to set the backdrop and scene for them, by briefly examining the history of this vital and dynamic industry in the Australian context. Gold mining in Australia had its official beginnings in 1851 when John Lister and William Tom discovered gold at YorkyÆs Corner, later renamed Ophir by Edward Hargraves. From that first tentative beginning, the ensuing rush of prospectors into New South Wales and Victoria meant that the annual gold production in those early years surpassed that of the next 40 years. This early rate of production was only eclipsed when AustraliaÆs production was once again lifted by the discovery of gold on the other side of the continent, in Western Australia. (Figure 1). The years leading up to the First World War saw Australian production peaking once again at over 115 tonnes of gold, a production rate that would not be surpassed until 1988. This renaissance in production at the beginning of the 1980s was achieved by the application of technology. The advent of bigger trucks and shovels meant that earth-moving costs dropped dramatically. This, coupled with the highly effective and efficient carbon-in-pulp processing route, stimulated the Australian gold mining industry into a state of frenetic activity. These two innovations were the principal factors that enabled the economic exploitation of the lower grade haloes left by the æold-timersÆ around the deposits exploited at the beginning of the last century-no high finding costs here. AustraliaÆs production through the 1980s and the early part of the 1990s was largely supported by the exploitation of these haloes. As these were depleted, the aggressive exploration effort stimulated by the strong cashflows of these early oxide deposits resulted in new æblindÆ discoveries which are now emerging as the backbone of the Australian industry (Figure 2). Gold production is a major contributor to the Australian economy. In 1998/99 the Australian gold industry accounted for approximately 16 per cent of the value of all mineral exports, which in turn accounted for over 35 per cent of AustraliaÆs total exports. As such, the Australian gold industry, by itself, accounts for just under six per cent of AustraliaÆs total exports (Figure 3). Consequently, the industry is responsible for over one per cent of AustraliaÆs gross domestic product. These statistics are all the more compelling when we consider that, at the beginning of the 1980s, goldÆs contribution to exports and GDP was insignificant (Figure 4). Within the Australian resources industry, gold mines and associated infrastructure account for ten per cent of all capital expenditure (Figure 5). From an employment point of view, in 1997/1998 the industry directly employed (excluding contractors) about 7700 people, approximately 15 per cent of all those employed in the minerals industry. Just under nine per cent of the workforce in the minerals industry are female, whereas in the gold industry over 16 per cent are female.

Jan 1, 2000

By Y Wan, L Liao

Organo-montmorillonites were synthesised by intercalating different amounts of dodecyl trimethylammonium bromide, cetyl trimethyl- ammonium bromide and stear trimethylammonium bromide into montmorillonite layers, and were used for the adsorption of 17b-estradiol in aqueous solution. The adsorption kinetics and thermodynamic of 17b-estradiol onto organo-montmorillonites and the effect of pH on the adsorption capacity of organo-montmorillonites for 17b-estradiol were studied. The adsorption isotherms at 20¦C, 35¦C and 50¦C were measured. Results show that organo-montmorillonite has a high affinity for 17b-estradiol. More 17b-estradiol can be adsorbed on to organo-montmorillonite and the adsorption is more rapid at a lower temperature. The montmorillonite intercalated with cetyltrimethyl- ammonium bromide with the amount equivalent to one times of its CEC has the highest adsorption capacity. For all organo-montmorillonites synthesised in this study, an optimum pH (around nine) for the adsorption of 17b-estradiol exists. Before this pH 17b-estradiol uptake increased with increasing pH. After that the 17b-estradiol uptake decreased with increasing pH. Simulation of the isotherms indicated that the adsorption of 17b-estradiol onto organo-montmorillonites is a spontaneous and exothermic process. Endocrine-disrupting chemicals (EDCs) are the focus of current environmental concern, as they can cause adverse health effects in an intact organism, or its progeny, subsequent to endocrine function. Most EDCs are man-made organic chemicals (industrial chemicals, crop protection products, antifouling compounds, pharmaceuticals and personal care products). In addition, EDCs can be naturally occurring in the environment (eg the natural female hormones estrone and 17b-estradiol). Therefore EDCs, especially estrone and 17b-estradiol, are ubiquitous in the aquatic environment receiving sewage inputs. Estrogen and 17b-estradiol are among the most potent of all EDCs and are sufficiently stable to survive present sewage treatment processes and are reactivated during those processes through deconjugation (Clara, Strenn and Saracevic, 2004; Zhang and Zhou, 2005; Fukuhara et al, 2006; Butler and Guilbault, 2006; Volpe et al, 2006; Ren et al, 2007; Zeng and Li, 2007). In comparison to traditional contaminants such as pesticides, the concentrations of the most potent EDCs are low, generally within ng/one range. The current sewage treatment processes have limited capacity in removing certain EDCs (eg 17b-estradiol, C18H24O2) It is therefore essential to install additional treatment processes to remove them from wastewater before discharge (Zhang and Zhou, 2005; Fukuhara et al, 2006; Lee, Jung and Kim, 2006). Adsorption is considered to be a possible way to remove EDCs from aqueous solution. Various adsorbents have been studied, including chitin, chitosan, ion-exchange resin, activated sludge, activated carbon (Clara, Strenn and Saracevic, 2004; Yoona and Westerhoffa, 2003; Zhang and Zhou, 2005; Fukuhara et al, 2006; Ren et al, 2007). Studies have shown that organo-montmorillonite has a high affinity for organic pollutants (Li, 1997; Zhu et al, 1998; Han et al, 2001). The aim of this work is to investigate the feasibility of removing 17b-estradiol from aqueous solution by adsorption onto organo-montmorillonite.

Jan 1, 2008

By Hoberg H, Schnieder FU

The disposal of residues from coal preparation and processing will to an increasing extent require investigation and consideration of the environmental problems resulting as a consequence of this. Different authors (Diingelhoff and Plankert, 1983; Hasenpatt, 1985; Szczepanska and Twardowska, 1987) have concentrated primarily on the content and the mobilisation of inorganic contaminants such as chlorides, metals and heavy metals from spoil tips, while no publications have yet been found on the question of a possible emission of organic contaminants (PCB, PAH, HC HC) from processing residues. Here the flotation residues in particular are able to bind larger quantities of organic contaminants by physi-sorptive means because of their large specific surface and, after disposal, to be re-emitt than into the environment. The flotation agents used in coal flotation are mixtures of technical distillation products with a correspondingly fluctuating composition. As Hey, 1986 showed, they may contain, in addition to the main components (n-alkanes, alcohols, surfactants), over 50 individual trace substances. In conjunction with the structural-chemical similarity of the individual components, this complicates the quantitative analysis of individual components considerably. For the analysis of hydrocarbon content of flotation products by means of extraction with organic solvents in accordance with DIN 38408, H18, the difficulty arises, besides the insufficient sensitivity at low concentrations, that geogeonic hydrocarbons are extracted from the coal as. well and the analysis results are thus falsified. These problems were overcome by the application of the 14C radiotracer method where certain components of the flotation agents are marked with radioactive carbon (14C). By measurement of the radioactivity of solid and liquid samples, the concentration of the marked substance can be measured very sensitively and precisely, whereby the accumulative measurement of similar organic substances is ruled out. Thus the reaction path of certain substances in complex reagent mixtures such as flotation agents can be traced excellently and the conceivable environment burden resulting from flotation tailings disposal can be estimated. In this paper, the adsorption behaviour of typical components of coal flotation agents are investigated for different coals and types of gangue material, the reagent content of flotation concentrates and tailings, as well as the mobility of the reagents adsorbed onto solids. The knowledge of adsorption and desorption mechanisms of unpolar hydrocarbons emulsified in water to solids are also of particular interest for the understanding of processes of organic soil contamination and for the further development of washing processes for oil-contaminated soils.

Jan 1, 1993

By K D. Tuckwell

The Treasurer, the Hon Wayne Swan, has nominated ‘maximising our advantages’ from ‘Mining Boom Mark II’ as the focus of the 2011/2012 Australian Budget. Australia therefore requires a bolder and better integrated economic reform agenda if it is to convert current strong demand for mineral commodities into lasting prosperity that benefits all Australians. Lasting prosperity, well past 2012, will only be achieved if Australia can effectively reverse a decade-long deterioration in the minerals industry productivity performance due largely to capacity constraints that inhibit growth. This requires improving the efficiency of energy networks, transport infrastructure, water markets, health and education services, access to skilled people and by streamlining costly, inefficient project approvals’ processes. The common thread that holds this economic fabric together is the importance of having the right people using the most appropriate technology within the correct policy framework.In December 2010, employment in the minerals sector stood at 187 200; 21 per cent higher than one year earlier, 15 per cent higher than the industry employment peak prior to the global financial crisis in 2008 and 14 per cent greater than anticipated by industry modelling published in 2008. Managers and professionals make up approximately 15 per cent of the total workforce, yet minerals-related higher education programs (mining engineering, metallurgy and geoscience) continue to be chronically underfunded, requiring direct industry subsidies of more than $25 M over the last decade. Also, the publicly-funded Vocational Education and Training (VET) sector continues to fail the industry in the delivery of quality training programs. Importantly, the industry is a key driver of economic activity in regional and remote Australia and is the largest source of private sector employment for Indigenous Australians who comprise up to a quarter of employees in certain locations.This presentation looks at what our industry and country need to achieve to ensure we have the right people for the challenges ahead. **This is an abstract only. No paper was provided for this abstract.**

Nov 22, 2011

The mineral sands deposit of Australia pose a number of unique, and quite unusual problems for the explorationist. Most concentrations of heavy minerals have been found in the unconsolidated sediments of the east and west coasts. Mineral sands mines open larger areas per tonne of concentrate than most other mines. This is because of the shallow depth of the sands containing the heavy mineral concentrations. Obtaining tenure can, by mining industry norms, be a massive operation due to the large areas to be examined and, particularly on the east coast, the large number of land holders encountered. A commercial development can still emanate from anything ranging from a small high grade body to a massive low grade deposit, the prices currently being obtained for rutile, zircon, ilmenite and monazite, although still modest when the remarkable properties and applications of these minerals are considered, is nevertheless attractive when compared to the prices being obtained for the base metals with the exception of gold. The current interest in the location and definition of new reserves of heavy minerals reflects this relative price attractiveness. The discovery of heavy mineral concentrates does not necessarily ensure the early establishment of a mine. Because of the cyclical nature of market prices, the average returns likely over the life of the mine permit the employment of only relatively simple, low cost, mining, concentration, and separation processes. If difficult mining conditions are encountered or the removal of small contaminants by complex metallurgical processes are required, then higher market prices must be obtained. Until the market is prepared to pay more for the commodities so produced, the resource will not be economic and lower cost reserves will be mined in preference. The Australian mineral sands industry has seen many closed mines because of past failures to properly assess the data base collected during the exploration and development phases of the failed projects.

Jan 1, 1987

By Broome A

In a technologically oriented industry, it is important to understand and apply technology very consciously to create competitive advantage. Technology is not an activity which is simply restricted to CSIRO or the research and technology department. Technology improvement is a part of everyone's role. It is a way of life - the technology facet of continuous improvement. For this reason, The AusIMM has organised this Travelling Technology Forum - a series of presentations about automation in mining. To make the message more accessible, The AusIMM had originally planned to take the Forum to four regional mining centres: Mackay/Townsville, Singleton, Burnie and Kalgoorlie, but only one seminar was held, ie at Singleton in March 1997. Seminars at other locations were cancelled because of insufficient registrants. The presentation by Andrew Logan of BHP Cannington was not available for the Singleton forum. The aims of the forum were: ò to heighten awareness of the key technologies and their impact in the minerals industry in the medium term; ò to foster creative thinking; ò to encourage people to broaden their technical and commercial skills and develop individual networks and linkages based on an interest in these key technologies; ò to share information on the application of these technologies in the industry; ò to promote an enhanced appreciation of the need for an innovative culture; and ò to encourage staff to consider post graduate courses in technology management. The AusIMM wanted to not only raise awareness about `automation in mining' issues, but also to get technology in a more general sense back onto `centre stage'. The Forum was generously supported by CSIRO, Western Mining Corporation Ltd, BHP Coal Ltd, Aberfoyle Limited, Goldfields Ltd, Novacoal Australia Pty Ltd, Pasminco Ltd, and RGC Limited. The program was endorsed by the Centre for Mining Technology and Equipment (CMTE). Copies of the full papers are available from the authors, see `References'.

Jan 1, 1997

In general the iron ore industry has been slow to adopt the Whittle Pit optimising software in the evaluation of iron ore deposits. The reasons for this are two-fold:the iron ore industry has developed techniques, usually bespoke software residing in the corporate offices of the respective iron ore companies, to establish their final pit limits; and the fact that the Whittle software doesnÆt easily lend itself to estimating a sales product of constant quality without maximising grade (metal content). The Whittle software is based on the work done by Lerch and Grossman (in the early 1970s), which proposed that graph theory be used to establish an optimal surface that maximises the revenue from a deposit. The maximised surface created in the pit optimiser is translated into a proposed optimal final pit shape that can be used by the mine design engineers as a target outline to lay out the final practical pit. By treating a geological and ore resources model that was created for an iron ore deposit as a subset of the recoverable resources estimation (RRE) type of geological models, the evaluation of an iron ore deposit and establishing the final pit is greatly simplified in the Whittle 4-X optimiser. Instead of trying to optimise the iron content of the deposit, the emphasis swings to maximising the extraction of a finished and saleable iron ore product. This is achieved by treating the finished saleable iron ore as an element in the multi-element Whittle optimiser. The quality of the finished sales product is represented, and the material that cannot be used in the blended product is also shown. Proposals for enhancing the functionality in the Whittle 4-X optimiser to make the evaluation of iron (and coal) deposits easier includes the creation of a new reporting function that will allow the user to specify which field(s) can be used as the divisor(s) for the reporting of the element grades in the model.

Jan 1, 2007

A method is presented for calculating the number of cycles of stress to failure of a drill rod from operating variables; a mathematical analysis by Cooper of the stresses present in drill steels is applied to the forged collar, i1i-in. hexagonal hollow drill steel in common use in Australia; and an estimation is made of the dry fatigue limits at various points along a drill rod.It is shown that these calculations predict failure at a 'point where failure rarely occurs, and do not predict that failure should occur where it does in practice. The reasons for this anomaly lie in the neglect of bending stresses in the stress calculations, and in failuredue to corrosion fatigue at a preferred section rather than to simpler fatigue under non-corrosive conditions.INTRODUCTIONIt has long been recognized that failure of metal sections by fatigue is influenced both by the number of cycles of stress imparted to the section (N) and by the magnitude of this cyclic stress (8). In this paper, both Nand Shave been calculated for rods which have failed in service, and whose operating history is known. While the calculation of the number of cycles to failure is·simple, the calculation of stress is more complex. The results of stress caIculations predict that failure should occur only hi short rods, and then preferentially at the tip end rather than the shank end.However, in actual fatigue failures of steel rock drill rods, approximately 75 per cent. of such failures are close to the shank end, and failures near the tip end are rare.The usual explanation given for this high incidence of shank-end failures is that at the point of failure there exists, in forged collar steels of the type common in Australia "hardness valley" or. "m'etallurgical notch". This narrow valley in hardness is a weakness, and failure is expected to occur at the weakest point at the bottom of...

Jan 1, 1955