Search Documents

By Onton W

During the latter part of 1936, conditions encountered in sinking the Main Ore shaft made it impractical and uneconomical to continue deepening it to serve haulage levels below the present No. 5 level. Plans were therefore made for an interior shaft, to serve new lower levels, that terminated above No. 5 level so that ore hoisted could be drawn off on this level and transported to the Main Ore shaft for final conveyance to the mill crude ore bin. The No. 2 interior ore shaft was only developed below No. 4 level and borehole ropeways with a winder located on the surface were installed in preference to an underground winder installation. No. 2 ore shaft with borehole ropeways commenced lead ore hoisting operations in September 1938. Apart from the copper ore hoisted in the war years of 1943-46, lead ore was hoisted to No. 5 level until September, 1951.

Jan 1, 1988

Geomechanics is one of the more specialised aspects of site supervision on a major tunnell- ing project. The controlled deformation of a rock mass as a result of tunnelling and the knowledge of loading of temporary and permanent underground supports are important for safe, economic construction. These basic parameters depend on the construction method and sequence and the geological conditions through which a tunnel is driven. Thus geomechanical monitoring during the construction phase provides feedback to a design team and allows any revisions to a design to cater for local conditions not revealed by earlier investigations. Detailed geological mapping is an integral part of geomechanics in the construction phase. It serves as a monitor on pre construction predictions and also forms part of the as- constructed record. If conventional excavation-techniques are adopted, geomechanics can provide a service of blast' vibration monitoring of surface structures in urban areas.

Jan 1, 1976

By Ely K. W

On January 21, 1986, a methane ignition and subsequent mine fire occurred in the under- ground workings of the Jim Walter Resources, Incorporated No. 3 Mine located near Adger, Alabama. The fire, which began on a longwall face and eventually spread into the adjacent gob area, could not be extinguished directly and raged out of control for several hours. Sealing operations were begun underground by Mine Rescue Teams and the fire area was successfully sealed with the mine able to resume production in about one month. The No. 3 Mine liberated over sixteen million cubic feet of methane in twenty-four hours. The operation was unique, in that, the successful underground sealing of a fire in an ultra-gassy mine had not been attempted or com- pleted for several years. Maps and charts are included to give explanation of the typical data used to manage the recovery effort.

Jan 1, 1988

By Hengst B

The first production stage in any mining operation is the breaking of whole rock into fragments small enough for loading and subseq- uent handling. This primary fragmentation is most frequently accomplished with blasting. The maximum fragment size and the fragment size distribution have an influence on the subsequent loading, handling and crushing costs. It is assumed that total rock fragmen- tation in practice is a result of an interact- ing array of radial cracks from various blastholes. The representation for the basic pattern of radial cracks emitted from a particular blasthole is first described. A model is then developed simulating the interaction between blastholes at various burdens and spacings, and in simultaneous and delayed modes. The resultant picture is analysed and a fragment size distribution calculated. Methods of incorporating the existing faults in the rock are also discussed. Finally application of this model to various facets of mining are considered.

Jan 1, 1977

By Bratt G. C, Horsham T. R, Langlois D. R

Mercury is precipitated from weakly acidic sulphuric acid plant waste liquor at the Risdon Works of the Electrolytic Zinc Company of Australasia Limited. Factors determining the choice of process and reagent, as well as details of process development including scale- up, and the time scale of implementation are outlined. The plant is designed for a maximum flow of 120 m3/h.of liquor containing mercury and saturated with sulphur dioxide. Mercury is precipitated by fluidised beds of aluminium pellets contained in lead columns. Liquor is then clarified with plate and frame presses. Experimental work on the mercury precip- itation reaction was conducted in three phases involving a scale-up of 100 times in equipment size. Extensive pilot filtration work was carried out on a 1 m2 press. Scale-up of 120 times was required for specification of plant filters. The basis of scale-up is outlined.

Jan 1, 1977

By Strickland R. E J

Heap leaching is establishing itself as an efficient method for the extraction of gold from low grade ore. It has the advantage of low capital costs, low operating costs and rapid startup. However, not all ores are amenable to heap leaching. It is only applicable to well oxidized ores that have reasonable permeability characteristics. Ore with excess fines or clay often display low permeability and are unsuitable for heap leaching.In this study, an attempt has been made to increase the rate of cyanide leach solution percolation by flocculating clay particles or reducing the surface tension of the leach solution. A wetting agent was found to decrease the rate of gold dissolution, possibly by presenting a hydrophobic surface to the gold particle. Flocculation of the clay increased the solution flow rate. The flocculation agent had no affect on the total gold leached but decreased the leaching rate.

Jan 1, 1992

By F Pothitos, S Hewson

The geological and geotechnical conditions at the Cadia Hill Open Pit are very complex. This complexity coupled with high mining rates has required significant technical input into the design and optimisations of the pit slopes, accesses, cutbacks and scheduling. A multi-discipline team of NML engineers, geologists and external consultants has been conducting comprehensive geological and geotechnical programs in order to achieve an optimum design of the pit slopes. Extensive data collection, analysis and interpretation has led to the formation of working geotechnical models of large structures, rock masses, and back-analysed slope performance charts. The current Cadia Pit Optimisation Project focuses on the risk-and-return principle for pit design and on the integration of geotechnical, hydrogeological, mining engineering and scheduling. The risk management for pit design has also been incorporated into the short term and long-term operation of the pit mining to ensure safety and production.

Jan 1, 2003

A substitute for rutile can be produced by leaching natural or pre-treated ilmenite in hydrochloric acid. Ilmenite in its natural form is an extraordinarily inactive mineral from which the selective removal of iron is rather difficult. The reactivity of ilmenite so that it can be leached with dilute hydro- chloric acid (=2O% w/w) can be enhanced by pre-treatment steps of oxidation and re- duction. The temperatures at which oxidation and reduction are carried out have an effect on both the kinetics of these steps and the leaching kinetics and optimum temperatures for oxidation and reduction are 950 and 850¦C respectively. The mechanism of leaching of iron from pretreated ilmenite and the effects of rate of agitation, temperature, acid con- centration and addition of ferrous chloride to hydrochloric acid on leaching kinetics and production of fines are discussed in the paper.

Jan 1, 1984

By Wright D. C

The operation of the cyanide-sensitive Mintek/TB1 kegold electrode was studied in the laboratory, with regard to equilibration time and drift, the effects of pH, stirring, salinity, dissolved oxygen, zinc and copper(I) ions. Methods for valid calibration in the range 20-600 mg(NaCN)/L and pH values in the range 9 - 12 in the absence of copper were also studied. Increasing the salinity beyond a threshold of 40 g(NaCI)/L improves calibration and measurement. The sensitivity is 91 mV per decade change in the concentration of ionic cyanide, and output is reproducible to within 10 mV with attention to the factors listed above. However, salinity of 40 g(NaCI)/L also sensitises the electrode to interference by copper(1) ions. This copper sensitivity seems capable of saturation, suggesting a research strategy for possible remedies.

Jan 1, 1996

The accurate calculation of ore reserves is one of the most important functions under- taken at a potential or operating mine. In recent years there has been a trend towards recommending more and more complex techniques for the calculation of reserves. However these are not always necessary and many improvements could be made by the use of all potential data and a heavier geological input. An ore reserve should be the result of geological not mathe- matical or engineering reasoning. All ore reserve estimates are wrong and the important thing is to.recognise why they-are wrong and to take action to minimize the errors. Geostatistics and other complex mathematical techniques may appear to answer all our needs for ore reserve accuracy but there are many drawbacks, not least of which is the communi- cation gap which may develop between the operator and both management and production Personnel.

Jan 1, 1979

An empirical kinetic model is discussed that enables the number of stages in a carbon-in-pulp plant and the amount of carbon in each stage to be calculated for any desired metallurgical performance. It is shown that a knowledge of the kinetics of gold extraction by activated carbon in each stage assists plant operators in the important' areas of process control and optimization. Factors such as mixing efficiency, concentration and distribution of carbon through the plant, bypassing of pulp through a stage, and carbon poisoning are examined. The resin-in-pulp process for the extraction of gold cyanide is also discussed, and the chemistry of absorption and elution on strong- and weak-base resins is examined. In addition, operating results from a small-scale resin-in-pulp pilot plant are presented, and various applications in which resin-in-pulp may be preferable to carbon-in-pulp are discussed.

Jan 1, 1982

By Selby DW, Hamill J, Cauley ID, Thomas I, Thornton AJ

The main objective of sulphide flotation in a cassiterite concentrator is to remove sulphide minerals (pyrite, pyrrhotite and sometimes chalcopyrite) from the ore prior to gravity concentration. Tin losses in the sulphide flotation stage account for a significant proportion of the total tin loss. separate studies of the sulphide flotation circuits of Renison Ltd and Cleveland Tin Ltd were conducted to investigate reasons for the tin losses. Sampling surveys were conducted in the rougher-scavenger and also the regrind-cleaner sections of both plants. In both plants, the rougher circuits recover excessive quantities of liberated cassiterite, while recovery of the desired composite cassiterite-sulphide fraction is low. The regrind mills are successful in liberating the composite cassiterite in the rougher concentrate, but at the expense of increasing the proportion of very fine tin mineral. The cleaner circuits recover between 40 and 60% of the cassiterite received, and this is all lost.

Jan 1, 1978

The Permian coal in the Muja Coal Measures of Collie Basin of Western Australia has a subdued lustre because of the fine laminations of lithotypes, and the dominance of dull and dull banded lithotypes with minor bright, bright banded and fusinous types. The maceral composition of the coal is variable, however the macerals of vitrinite and inertinite groups dominate and the exinite and mineral matter contents are low. The lithotypes have low concentrations of trace elements and the boron concentration is between 10 - 100 ppm recorded only from the dull lithotypes. On the basis of organic petrology, the inter-seam sediments, flora and the very low concentration of boron, the depositional environment postulated for the coal is braided, fluvial and fluvio-lacustrine with marked fluctuations in the water table. The low water table in the environment accounts for fusain and inertodetrinite in the coal.

Jan 1, 1996

By Rieniets S, Somerville J. L

In Morwell Open Cut brown coal mine, the overburden 'firehole' materials which have resulted from ancient coal fires vary-from hard baked clays to firm laminated lacustrine clays. The need to pre-strip designated areas to reduce the slope height and attain safe digging conditions for the bucket wheel excavator operation is now accepted practice at the open cut mine. In this study, the inherent spatial variability of undrained shear strength of the clay materials has been incorporated in a visco plastic, finite element based, probabilistic slope stability analysis. Data on the costs of initial pre-stripping, excavation and slope failure are collected to provide an economic basis for the optimisation of the design of the overburden batters in Morwell Open Cut. This improved stability modelling is enabling costly pre-stripping to be minimised while ensuring acceptable slope stability conditions and minimising the risk to personnel and plant.

Jan 1, 1994

By Kissell F. N, Thimons E. D

The Bureau of Mines used sulfur hexafluoride (SF6) tracer gas to evaluate the effectiveness of gob ventilation and/or sealing practices at three coal mines, each having different problems associated with their mined- out areas. The purpose of these ventilation studies was to better understand whether current techniques employed for ventilation or sealing are successful at minimizing the potential for gob fires and explosions. The work performed at each mine is discussed: One is a longwall operation that uses ventilation to carry off hazardous gases, and two are room- and-pillar operations, each with far different concerns, that seal off the gobs to isolate them from the main mine ventilation. In all cases, employment of the Bureau's SF6 tracer gas technique resulted in answers to questions raised by the mine operators concerning the effectiveness of their gob ventilation or sealing practices in preventing mine fires.

Jan 1, 1988

By Waters A. G, Nightingale R. J

The quartzite added at the blast furnace for the purpose of adjusting the chemistry of the burden inputs is shown to have a disproportionate impact on both the level and the variability of the hot metal silicon (HMSi). This conclusion is supported not only by direct correlation involving data from five blast furnaces, but also by mass balances. In one case the R2 correlation coefficient was 0.96 and the mass balance was accurate to within five per cent for a wide range of quartzite additions. The results indicate that as much as 43 per cent of the silicon in the added quartzite reports directly to the hot metal. Indeed, silicon from quartzite was found to be much more likely to report to the hot metal compared to silicon from regular sources (eg coke and sinter), reflecting differences in the activity of the silicon source.

Jan 1, 1994

By Staunton W. P

The presence of cyanide soluble copper in gold ores can give rise to serious operational and economical difficulties in CIP and CIL operations. Cyanide consumption can result in the ore being uneconomic to treat by conventional means. Loading of copper onto carbon can also have deleterious effects on gold recovery and subsequent stripping and bullion recovery. The recovery of gold from high copper ores has been previously reviewed by Muir, LaBrooy and Cao (1989). Work undertaken for Mt Gibson Gold Project by Australian Mining Advisors with the assistance of the Chemistry Centre (WA) resulted in the patenting of a process and subsequent construction of a plant at Mt Gibson to overcome some of the difficulties encountered with copper. This paper discusses some of the work which was undertaken during laboratory investigations prior to commissioning of the plant and some further considerations for the treatment of high copper gold ores.

Jan 1, 1991

By Fukui M

An increase in pig iron output by 50 per cent was aimed at after re-lining No.2 blast furnace of NAKAYAMA STEEL WORKS. This had to be achieved by increasing both the furnace volume (from 673 to 757 m3) and its productivity, Without equipment for high top pressure operation, high productivity was mainly attained by the following three measures; (1) improving the gas flow characteristics by maintaining a high ratio of agglomerated ores, increasing the strength of sinter and coke, and optimizing the charge distribution, (2) decreasing the fuel ratio by low Si operation and the use of hot blast, and (3) oxygen enrichment. In addition, the tapping controls for pig iron and slag were intensified. As a result of the above measures an excellent hot metal output of 2.7 tonne/m3/day was attained in April 1979 (monthly average).

Jan 1, 1980

By Dimitrakopoulos R

Ore textures in base metal deposits are an important factor in the liberation of the economic components of the ore, metal recovery and reagent consumption during beneficiation. Optimising the mine profit requires knowing the relationship between ore texture and mineral processing behaviour, and the ability to predict the metal grade and the ore texture at a suitable scale. A new method that generates distributions of mesotextures for any mining block size or shape is proposed and includes: I . establishing a protocol for acquiring mesotexture data: 2. measuring the mesotexture spatial correlations using a multi-texture variogram; 3. generating multiple simulations of mesotextures; and 4. upscaling the simulations to generate the expected mining block/stope mesotexture distributions. Models of the ore textures built using the proposed methodology can be used to assess resources and reserves, enhance ore/waste discrimination and predict the metallurgical behaviour of parcels of ore.

Jan 1, 1997

By Y Li, L Zhang, G Li, S C. Dominy

Qiagong skarn iron (copper) deposit is located in Xietongmen County of Tibet, China (N 29¦52Æ14.9ö, E 88¦24Æ10.3ö). It is situated at the middle-western Gangdese porphyry copper-belt. Mineralisation is related to a Himalayan porphyry intrusion, with the mineralised body occurring at the contact zone between the Tertiary Takena Formation carbonate rocks and Himalayan monzonitic granite porphyry. The melt, melt-fluid and fluid inclusions were observed in early quartz, with most abundant fluid inclusions in quartz, calcite and garnet from the skarn. The geology and inclusion assemblage show a close relationship between iron (copper) mineralisation and a Himalayan porphyry intrusion. Based on preliminary inclusion studies, this paper discussed the characteristics, evolution of ore-forming fluid and affiliation to the Himalayan porphyry intrusion. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008