Search Documents

Mt. Whaleback, the property of the Mt. Newman Joint Venturers, contains more than one thousand million long tons of high grade hema- tite averaging 64% Fe, ranging from 70%, the grade of absolutely pure hematite, to 54%. The ore occurs in the Dales Gorge and Joffre Members of the Brockman Iron Formation. The interbedded shale bands common in other orebodies occurring in these horizons are seldom more than a few inches thick and are commonly partially enriched to about-35% Fe. In the generally hard, massive hematite orebody, the gangue minerals tend to break preferentially to the fines, or -6 mm product, and for this reason it is of a somewhat lower grade than the lumpy product. The control of the chemical qualities is concentrated on the fines product for it has been found that maintaining the iron and alumina levels in this product ensures that all chemical specifications are met in both the lump and fines products. Physical qualities are monitored to ensure that the physical quali- ties of decrepitation and degradation of the lumpy product are maintained at levels accept able to the buyers.

Jan 1, 1973

By West Coast Staff

Attention to the design of facilities for drainage, of both surface water and seepage, made it possible to attain, for a qam impounding residues from a concentrating mill, a more stable sand wall which can eventually be carried to a greater height.EXPERIENCE WITH No. 1 DAMResidue from the lead zinc concentrating mill, which treats the ore from the Rosebery and Hercules Mines, was pumped 3,600 ft. through a 5-in. diameter woodstave pipeline to the site of the dam. It was formerly delivered through a 4-in. steel pipeline.State laws prevent the residue being discharged to waste into the Stitt River. Furthermore, as a pyritic residue it is a potential source of sulphur.Between 1936 and 1956 more than 1,000,000 tons. of residue was paddocked. The run-of-mill product was roughly classified at the dam in a 6-ft. diameter cone classifier and the sand fraction was pumped by a 3-in. pump to the front wall of the dam across a shallow valley. The overflow gravitated to the rear of the dam (Fig. 1). Typical sizings were:

Jan 1, 1958

The application of single liquid cement for fracture grouting in base rock may have history more than 120 years. The disadvantage of it is difficult to increase the grouting efficiency, because the jelling time of it is very long and hard to control. The double liquid grout, such as chemical grouts and cement water glass grout was developed at the end of 1960.'s Although the jelling time of this kind of grout can be controlled, it mast adopt double liquid grouting technology, use complicated equipment and is not easy to control component's ratio of the grout. Another disadvantage for chemical grout is high price, and have pollution to environment. OCE series single liquid grout is the effective grout material developed recently by making large efforts in Ohina. Main feature of it is that the jelling time is easy to control, materials from cement and clay are very cheap and without pollution to environment, and the grout can be injected by single liquid technology. The effect of QCE series grout has been proven by its application in China. It can be believed that QCE grout has great economic efficiency and will give a push to develop grout material.

Jan 1, 1988

ADDRESS BY THE PRESIDENT OF THE INSTITUTE (MR. C. H. MARTIN) IN PRESENTING THE CERTIF1CATE TO SIR GEORGE FISHER, C.M.G.Members of The Institute, distinguished guests, of which there are many, ladies and gentlemen, you are welcome.And might I add a special welcome to Lady Mawby and Lady Fisher and to Sir George's only son Peter, who with his wife, Betty and one of Sir George's three daughters, Helen, are present this evening, and also to Sir Maurice's son, Colin, and Colin's wife, Jay, also in our company.The family presence must surely be a great source of pleasure and satisfaction to all those so intimately concerned.It is hardly. necessary for me to state the sole and only rC'l.son for our presence here tonight, which is to conJer on Sir George Fisher and Sir Maurice Mawby Honorary Membership of The Australasian Institute of Mining and Metallurgy, and at the same time to acknowledge two people who have rendered great service to the mining industry albeit tinged with sadness to all of us in the knowledge that from now on their influence may diminish.

Jan 1, 1976

By F Cesnik, P Griffin, S Green

In July 2004 a flotation concentrate regrind circuit was commissioned in the æHigh GradeÆ Ridgeway concentrator at NewcrestÆs Cadia Valley Operations. This was the culmination of two years of project testing, process design and planning which commenced shortly after commissioning the concentrator in March 2002. During the two-year project evolution alternative grinding technologies were evaluated from conventional ball milling through to sand milling. A Detritor mill was eventually selected for the duty and the criteria on which this selection was based will be presented. As the project evolved so too did the equipment sizing with the concentrator quickly exceeding design capacity of 4 Mtpa and currently averaging 5.6 Mtpa, the process design had to accommodate this and future potential throughput increases. This paper will focus on the supporting testwork, circuit surveys and concentrate properties which were used as the design basis for the project. The economic evaluation which led to the project receiving board approval in November 2003 will also be presented. Detailed design and construction management issues will be discussed as will preliminary results and findings up to November 2004.

Jan 1, 2005

By Wright S, Jorgensen F. R A

The reaction between lead sulphate and a number of base metal sulphides (galena, sphal- erite, chalcopyrite and synthetic pyrrhotite was studied as a means of desulphurizing lead sulphate containing fumes and residues to levels acceptable as ISF feed. The reactants were mixed with 50% zinc oxide to act as a "basket" to contain the molten products of the reaction and pressed into small briquettes 20 mm in diam. Factors such as temperature, time and the composition of the atmosphere were investigated. Using the PbS/PbS04 system as an example it was shown that the reaction became rapid above 800¦C and that both sulphur dioxide and oxygen in the atmosphere were detrimental to achieving low sulphur in the product. In an inert atmosphere all the sulphides when roasted for 1 h at 1000¦C gave results corresponding to the elimination of more than 95% of the sulphur in the reactants. Leach plant residues were considered for use as the "basket" material. It was shown that the residual sulphide and sulphate components of the residues underwent similar reactions to those experienced by the pure systems.

Jan 1, 1987

By George G

The Circum-Pacific Map Project is a cooperative international effort to prepare and publish geological, geophysical and mineral resource maps of the Pacific Basin and adjacent land areas. Earth scientists representing 180 organizations from more than 40 Pacific Rim countries are participating in the work. The project is directed by a committee established 14 years ago as an activity of the non-profit Circuin-Pacific Council for Energy and Mineral Resources. Technical and cartographic support is provided by the U.S. Geological Survey. The Circum-Pacific Map Project is organized under five regional panels of experts on the geology and resources of the four quadrants of the Pacific and Antarctica. A series of five 1:10,000,000-scale regional maps and a 1:17,000,000-scale map of the entire Project area, the Pacific Basin Sheet, provide the cartographic base. Forty-eight individual sheets are planned and thirty have been published in eight different series, including base maps, geography, plate tectonics, geology, energy resources, mineral resources, tectonics and geodynamics. Additional special single-sheet thematic maps on the Pacific Basin base have been published and are planned for a total of more than 50 individual sheets.

Jan 1, 1987

By I Arburthnot, N Lawler, C Loan

The function of a thickener is to optimise and accelerate the process of gravity sedimentation. The desired end product (be that maximised concentrated solids or clarified liquid) determines how the thickener is designed and operated.Significant internal research, together with extensive on-site piloting, by Outotec has resulted in the determination that the application of the appropriate amount and type of shear to hindered settling aggregates can result in a substantial change to the sedimentation process. A new patented technology, called shear enhanced thickening (SET), has been developed. SET results in considerable design implications for full-scale thickeners, including a substantial reduction in required footprint and/or significant increases in underflow density.The development of SET, combined with laboratory and pilot scale verification, will be discussed along with the introduction of this technology to a number of full-scale thickeners. The associated implications and benefits for industrial thickeners are outlined.CITATION:Loan, C, Lawler, N and Arburthnot, I, 2012. Industrial scale results from shear enhanced thickening technology, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 341-346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

With the use of 36 rock drills of the jackhammer type at the West Lyell Open Cuts of the Mt Lyell Mining & Railway Co, it is of importance to determine the economic as well as the physical life of these machines. With this purpose in mind records have been kept of the footage bored and the cost of new parts placed in each machine, and the following procedure adopted.A graph is plotted for each machine showing the footage bored as a horizontal line and at each 5000 feet of boring the total cost of new parts is noted on this line (see Figure 1). Thus at a glance it is possible to see the amount of work done by each machine and the money spent on it in new parts. However, it is difficult to visualise from this graph the increase in the cost of new parts for each machine as its life advances. To obviate this clifficulty a curve is plotted with the cost of new parts as the vertical component and the distance bored as the horizontal component.As before the cost of new parts are taken at each 5000 feet bored (see Figure 2).

Jan 1, 1994

By Kuruppu M

Geotechnical design plays a key role in mine design. A proper geotechnical design provides a safe working environment and facilitates efficient mining operation. There are mainly three design approaches: (i) judgmental, based on observational and experiential facts, (ii) empirical, based on empirical design formulae; and (iii) analytical, incorporating numerical analysis. Most design applications are based on the design methods one and two as mentioned earlier. However, complexities arise in deep underground mining operations and deep open pit mines. These complexities and difficult geological environment introduce more uncertainties and simple empirical formulae would not be adequate as a design tool. These situations require numerical modelling and analysis of the design problems including interpretation of the results obtained from the analysis. There are several tools available for performing the numerical modelling and analysis. A brief review of the available tools is provided. The authors selected ANSYS (a general purpose finite element analysis tool) for use in mining geomechanics and geotechnical design. This paper includes several examples demonstrating the applicability of this software in designing mining structures. The authors hope that the design examples will demonstrate the use of the numerical modelling and analysis applications in excavation design.

Jan 1, 1995

By Toop G. W, Martin M. T

At the Cominco Ltd plant in Trail, British Columbia, the Betts lead electrorefining operation requires that antimony and arsenic be present in the lead bullion for anode slimes stability control. Until 1986 the antimony and arsenic inputs from concentrates to the Lead Smelter needed to be supplemented with high antimony and arsenic content recycles from the Silver Refinery operation to maintain a satisfactory composition. Subsequently the antimony and arsenic inputs have increased as a result of increasing levels of antimony in Sullivan lead concentrate and the purchase of larger quantities of silver/gold bearing concentrates that inherently have higher antimony and arsenic levels. The increase has exceeded the limits required by the Betts process. It therefore became necessary to install a partial softening process downstream of the Continuous Drossing Furnace to satisfactorily control the bullion composition. Process control and oxygen injection techniques used in the partial softening process are reviewed. Approximately 8 tonnes/day of softening slag are produced having a combined antimony and arsenic content of 25 percent. This slag is reduced in a recently commissioned short rotary furnace followed by vacuum distillation of the metal for recovery of the antimony and arsenic values.

Jan 1, 1989

By Fink ST

Management requires up-to-date information on the activities of an enterprise in order to maintain control and to assist in decision-making and planning. In today's environment it is essential that this information is immediately available and in an easily assimilated format. If this is not the case, management is forced to make decisions based on intuition and past experience. At Mt Newman Mining Co, a computer application has been developed and implemented with the objective of providing this type of information to management. The Key Parameter Reporting System (as the application is known) allows for daily (constant) on-line capture of selected production statistics, safety statistics and free format textual comments relating to topics such as industrial relations, major maintenance and other pertinent news. Information can be retrieved,'and displayed or printed in either a tabular or graphical format. All senior managers have colour visual display units in their offices for immediate access to the system. Access to selected sensitive information is controlled. All company staff are able to retrieve unsecured information from the system via visual display units installed in all company Locations.

Jan 1, 1983

By Smith I. T

Mine operators have long recognised that the results achieved in primary blasting are critical to subsequent mining activities. With the introduction of "in the hole" drills under- ground and the advantages offered by the use of water gels in conjunction with ammonium nitrate-fuel oil (ANFO) explosives, new mining methods have been developed and enabled improvements in older methods. Pumpable water gels have been used with varying success underground. These gels allow a high loading density even in ragged bore- holes. The problems encountered with slumping in upholes is recognised so the current trend is to use these gels in downholes where wet holes are prevalent. Cartridged water gel technology has advanced to the point where it has allowed the replacement of nitroglycerin (NG) based explosives and pumpable water gels. Today, gels can be made as a tampable product for use in development headings or as a slump- ing product for downholes to give an effective coupling. With the introduction of the Tovex« pneumatic loaders, the problems associated with a pumpable gel were eliminated and gave the user the ability to alter his loading density.

Jan 1, 1977

By P Waters

BHP Billiton Iron Ore initiated a program in January 1995 at the Mt Whaleback operation in Newman, Western Australia to develop a closure plan for the overburden storage areas (OSA), which have the potential to generate acid rock drainage. The primary research program includes the development of technology for the long-term performance of OSAs with respect to slope stability, surface run-off, erosion, water infiltration and vegetation. The objective is to control acid rock drainage by preventing moisture movement into and through the OSA material. Infiltration to the underlying OSA material and closure costs are minimised due to the presence of the run-of-mine (ROM) cover material. A summary of the field data is presented to illustrate low percolation rates to the underlying OSA and key performance characteristics of the moisture store and release cover system design. Field data collected to date demonstrates that a moisture store and release cover system constructed with suitable ROM material has good potential as a final cover system at the Mt Whaleback site. The performance of the cover system on a sloped surface was significantly different as compared to placing the cover system on a horizontal surface.

Jan 1, 2003

By Bahsford A

The presence of coal in the Sydney area was confirmed in 1891 when Cremorne Bore No. I intersected cindered coal at 1 854 m. The decision to develop Sydney Harbour Colliery was based on the results of Cremorne Bore No. 2 (drilled in 1892) in which a 3.12 m. seam of unaltered coal was encountered at 889 m. Geologists from the New South Wales Department of Mineral Resources consider that this seam is probably equivalent to an upper split of the Bulli seam. Long Cove at Balmain was selected by Sydney Harbour Collieries Ltd. as the site for mine development in 1896. This was due to opposition to the proposed establishment of a colliery on the north shore of Port Jackson near Cremorne. Construction of the main access and ventilation shafts (termed Birth- day and Jubilee), other mine infrastructure and the quay wall occurred between 1897 and 1902. A fatal accident in which five men were killed occurred during the construction of the Birthday Shaft in 1900. This acci- dent resulted in amendments to the Mining Act providing for guide rails in shafts.

Jan 1, 1988

The Yabulu refinery of Queensland Nickel Pty Ltd located near Townsville now imports more than three million wet tonnes per year of nickel laterite ore from New Caledonia and Indonesia, making it the largest importer of any commodity in Australia. The project has illustrated that importing untreated bulk ore and re-exporting high value products makes good economic sense for the company and the nation. The economics of this exercise have been considerably enhanced in the past year by changing the project's principal product from nickel oxide sinter to refined high purity nickel metal. It is one of the few operations in the world where nickel ore is transformed to nickel metal at a single site. Several novel technological processes were developed at Yabulu and incorporated into the refinery to allow this product transition to occur. By utilising internally developed technology the new processes were installed at a capital cost of less than $10 million. It is unique for a large nickel producer to completely change the quality of its entire product range many years after the plant was constructed and considerable attention to marketing the new products has been required.

Jan 1, 1995

By E R. Ramanaidou, M S. Piggott

Transport to and handling of iron ore at Port Hedland, Western Australia, results in the generation of airborne particulates that contribute to the atmospheric dust load, with concerns about potential local environmental impacts (eg mangrove swamps) and possible human health implications. Mineral and chemical characteristics of the Background soil samples were contaminated with particles of iron ore as martite octahedra and grains of micro-platy hematite as detected by scanning electron microscopy (SEM) in the 2.5 - 10 ¦m and 10 - 50 ¦m size fractions. Fossilized wood fragments similar to those observed in Yandicoogina fines ore were also detected in some background soil samples. With a predicted increase in demand of channel iron deposits (CID) ores and the inherently dusty Marra Mamba ores (eg West Angelas, MAC, OB29/30/35, Marandoo), in conjunction with particulate emissions from hot-briquetted iron and direct reduced iron (HBI/DRI) processing plants, there is the potential for additional sources of anthropogenic dust to contribute to background levels. Mineralogical and chemical characterisation of the entire range of particulates that could be produced is necessary for a complete understanding of their potential impact on the local environment.

Jan 1, 2002

By Robins R. G

The dissolution of metallic copper powder in aqueous solutions of cupric sulphate under the influence of ethylene gas was investigated. The dissolution reaction stoichiometry obtained was: Cue+(aq) + Cu(s) + 2C2H4(g) = 2(CuC2H4)+(aq) The rate of formation of the copper (I)-ethylene complex in the above reaction was studied in a laboratory autoclave and the effect pH, temperature, ethylene partial pressure and initial concentration on the dissolution rate was measured experimentally and expressed theoretically in terms of several simple conceptual kinetic models. The results led to the selection of optimum conditions for the reaction and the suggestion of an "ion-molecule reaction" mechanism to explain the very low activation energies for the reaction system. The area of application of this reaction lies in the direction of refining impure copper such as cement copper. Several experiments were performed in which an acidified solution of cupric sulphate under ethylene pressure was used to dissolve copper from the cement copper powder in the form of the copper (I)-ethylene complex, followed by the release of gas pressure to disproportionate the complex and precipitate a purer metallic copper.

Jan 1, 1987

By Richardson G. W, Yap L. C

Friction rock stabilisers (FRS) are the most common steel-based ground reinforcement used in underground mines in Western Australia. As with any other steel-based product used in underground mines they are susceptible to corrosion, particularly under aggressive minewater and mineral conditions. Because of their thin-wall tubular construction and large surface area, the potential damage resulting from corrosion is considered to be more severe for this type of reinforcement than for other forms of reinforcement made of solid steel bars. Because of the obvious safety problems which may result from corrosion, both mine operators and regulators have raised concerns regarding the long-term effectiveness of FRS installed in underground mines in Western Australia. Although corrosion has been recognised as an important safety issue, the controls of corrosion in varied underground mining environments has not been well understood. To improve the understanding of the corrosion behaviour of FRS, the Department of Minerals and Energy has initiated a research project focused on the mechanisms and extent of corrosion attacks, and their influence on the effectiveness of the reinforcement. This paper describes the research project and presents the interim results achieved To-date.

Jan 1, 1995

Lightweight polymer grids have recently been introduced to the mining industry. They are currently being used for roof and rib control, longwall shield recovery, safety guarding or barricade, highwall screening, internal reinforcement of gunnite/shotcrete applications, sub-base reinforcement, construction of steepened slopes, retaining walls, mine reclamation (i.e. erosion control, turf reinforcement), and in numerous mining waste related projects. These polymer mining grids utilize a strong, lightweight polymer, usually special grades of polypropylene or polyethylene. High tensile strengths are achieved by molecular orientation of these polymers in the manufacturing process. The first step in the manufacturing process is to extrude the polymers into thick continuous sheets. These sheets are then punched, and drawn into open grid structures. Aperture size and configuration are controlled by the geometry of the punched hole and the degree to which the grids are stretched. The drawing process is the key to the molecular orientation required for the tensile strengths. These long chain polymer molecules in their natural state have a random orientation. When stretched, the molecules are pulled into a parallel alignment, thus creating a lightweight product with tensile strength comparable to Steel.

Jan 1, 1992