Search Documents

The problem of instantaneous outbursts remains unsolved after over a century of events and the investigation of the mechanism of the phenomenon and means of treating it. Outbursts have occurred of up to 5,000 tonnes with perhaps up to 500,000 m3 of accompanying gas, either methane (CH4) or carbon dioxide (C02) or mixtures. The low density of CH4 and the high density of CO2 give particular problems. Australia with both gases has experienced outbursts for 85 years with fatalities as recent as 1978. The Bulli Seam of the Illawarra area of the Sydney Basin is affected and outbursts with both CH4 and CO2 occur. The Northern and Central Bowen Basin also experiences outbursts with both gases. Proneness of affected mines is related to the high rank of the'coal and the proneness of the seams-is localised according to depth, gassiness, structure and development geometry. Proneness may be reduced by appropriate choice of mining methods. In addition to outbursting mines other mines have symptomatic phenomena. Traditional preventive methods have been used and control by induce- ment has been practised. A method of local prediction for widespread use has not been achieved although locally successful prediction 1Superintendent Rock Mechanics and Strata Control, The Broken Hill Proprietary Company Limited, Steel Division Collieries, Wollongong, N_RW

Jan 1, 1980

By W Boughton, L Gilbert

The Australian Water Balance Model (AWBM) has found widespread use in Australia in estimating the streamflow behaviour of catchments. It has been used at the Ridgeway Gold Mine, in central west New South Wales, to estimate streamflows in creeks potentially affected by loss of spring-fed baseflow due to mine dewatering. The AWBM estimates are used to assess the effect of mining on streamflows and the need to provide compensatory flow releases, which would be drawn from mine water supplies, into the creeks, in compliance with regulatory consent requirements. The monitored flows in some of the creeks exhibit non-typical behaviour, with streamflows increasing in autumn months despite a lack of significant rainfall. This behaviour is believed to be due to the combined effects of discharge from rock fractures and the effects of evapotranspiration in the riparian zone. A modified version of the AWBM has been developed which much more closely simulates the observed flow behaviour and which will be used in ongoing flow assessments for the mine. This paper outlines the difficulties involved in modelling low flows in small catchments that are subject to a number of influences (other than mining), describes the development of a refined model to improve simulation of low flows and baseflow in small headwater catchments and highlights the need for good baseline data to calibrate such models.

Jan 1, 2006

In recent years a large amount of work has been done at various plants overseas, and also at Broken Hill Associated Smelters, Port Pirie, South Australia, on the use of Dwight Lloyd sintering plant gases for sulphuric acid manufacture by the contact process.Several plants have modified their sintering machines and operating procedure, and some have adopted gas recirculation techniques, to obtain a relatively high proportion of the sintering plant gas at an S02 concentration acceptable to a contact acid plant 1.These adaptations were investigated at Port Pirie, and it was found that gases of suitable S02 concentration could be obtained. The results justified installation of a contact acid plant and a decision was accordingly made in 1949 to construct such a plant.However, the local conditions presented some difficulties not generally encountered at other plants, the chief differences being:a. For maintenance of production of 98% H2S04 , an unusually high S02 concentration is required, because of the prevailing high temperature 'of the purification train cooling water.b. The entire sintering operation is conducted on two large machines, 55ft. x 10ft., operating in series as "First" and "Second over" machines (a two-pass roast.) Any interruption" to either machine causes a complete interruption of plant operation and gas flow.

Jan 1, 1951

By S Youds

The backfilling operation at Olympic Dam mine supports a 9.8 Mtpa underground Long Hole Open Stoping (LHOS) operation. It involves a combination of Cemented Aggregate Fill (CAF), surface rockfill and underground rockfill. The fill material is introduced from the surface via boreholes into the top of the stopes. Due to the deleterious effects of the dust and the thickness of the atmosphere in the stope it is not possible to view the filling process either at optical or infrared (IR) wavelengths. The need for a means to measure the filling process is driven by the placement of both rock and CAF fill in the stopes. The large volumes and high relative cost of CAF makes the minimisation of CAF fill a business priority. Incorrect filling can lead to the sterilisation of ore reserve. The use of millimeter wave radar to view through the haze to give real-time data on the relative positions of the different fill masses is being developed as an in-stope fill monitoring device. This paper reviews the salient points of the technology and its potential use in the backfilling operation at Olympic Dam. The broader potential of this technology for use in the mining industry by æseeingÆ through water and dust laden environments such as that found in stopes and ore passes is also discussed.

Jan 1, 2002

The Electricity Generating Authority of Thailand own and operate an opencut mine supplying coal to on-site power stations at Mae Moh, 600 km North of Bangkok. The mine is being expanded from an annual production of 1.5 million tonnes per year in 1982 to over 9.5 million tonnes per year by 1991. The mine will be amongst the largest open pit operations in the world. It is technically difficult to operate and plan due to complex geology, weak strata and surface constraints including reservoirs, forests and traditional villages. This paper presents a case study of mine planning for the above project including associated collection and processing of geological and geotechnical information. The existing operation is described, as well as the strategy adopted for the mine at expanded production. The planning covers various phases of mine planning including a Conceptual Study, a Definitive Study and detailed short term planning. Each stage incorporated new information and reflected a higher level of confidence in the data and resulting plan. Sophisticated computer techniques were required including geological modelling, calculation of volumes, geotechnical analysis, scheduling and costing. The planning was undertaken on site by a team of Australian and Thai Engineers as part of the Thailand-Australia Lignite Mines Development Project which is a four year programme of assistance funded by the Australian Government.

Jan 1, 1986

By P Fines, D J. Williams, G W, S Miller

This paper presents the results and findings of geochemical and mineralogical testwork conducted on samples collected from waste rock dumps at two mine sites, located in South Carolina, USA (Site 1) and Sudbury Ontario, Canada (Site 2). Important aspects of the relationship between the physical and geochemical aspects of the dumps are also presented. The overall aims of the project were to 1. determine if the physical and hydrological nature of the waste-rock dumps had any impact on the geochemical and mineralogical characteristics of the dump materials; and 2. to identify key implications for dump construction for ARD control. The results of geochemical and mineralogical tests indicate that the waste rock at Site 1 had undergone significant in-dump weathering and was relatively advanced with respect to ARD evolution. In contrast, the waste rock at Site 2 had undergone some weathering, however still contained a considerable amount of sulfide minerals. Testing also suggested that flushing of oxidation products at Site 2 had been limited, which therefore promoted the storage of oxidation products at the site. In addition, materials that had a D50 particle size in the range of 5 mm to 30 mm appeared to be more readily flushed than samples that had a D50 particle size of 30 mm. This suggested that preferential water pathways may have developed within the dumps at both sites.

Jan 1, 2003

By Swift D. G

For some time the Electricity Trust of South Australia (ETSA) has been investigating the application of new mining methods and equipment to minimise the cost impact of the steadily increasing depth of mining brought about by the 20¦ dip of the coal seams at the Leigh Creek Coalfield. Exhaustive examination of all suitable mining systems showed that highly mechanised systems involving belt conveyors displayed no eco- nomic or operational advantages over shovel and truck methods. However, the configuration of the Leigh Creek coalfield allows for two quite different approaches to mining by shovel and truck. The current strip mining method involves removing overburden from the highwall in 60 m to 200 m wide strips to progressively expose the coal down dip, and requires all waste to be hauled to the surface. The alternative ter- race haulback method involves opening a boxcut to full depth at one end of the coalfield, then mining the full section along strike and placing the spoil in the mined out area. On a strictly economic basis, the latter is clearly advantageous, but the former has significant less tangible advantages. In deciding between the two methods ETSA is faced with the need to examine the applicability of each method under a wide range of possible future demands on the coalfield, and to assess the importance of many intangible factors.

Jan 1, 1989

The distribution of p(~rphyt1 copper deposits, in time as well as place, is used to propose an occurrence model based on the genesis models of Sillitoe and Rona. A magmatic source of the metals is accepted. The characteristic metallogenic epoch and the migration of the mineralization event along an elongate metal province are explained as the result of subduction of an obliquely- oriented strip of mineral-enriched material on the oceanic plate. Two mineral-enriched trails emanate from a hot-spot source of high-intensity hydrothermal activity in an oceanic rift. Because the whole plate system moves relative to hot spots, the hydrothermal source appears to migrate along the rift, and the two trails are not parallel to transform faults, but form a broad "V" centred on the hotspot. Source loci are spaced at intervals of about 3000 km, resulting in the possible repetition of metallogenic epochs, in a subduction zone province, at about 100 m.y. intervals. The position of the mineral-enriched strip can be found graphically, given ages of a series of deposits in a province, and the plate convergence vectors. This knowledge provides an exploration tool at regional scale and, by reflection across the rift, the potential for exploration is extended across oceans. The model has implications for commodities and deposit types other than porphyry coppers.

Jan 1, 1987

Diamond drilling is a relatively new commodity in terms of drilling. The first known diamond drilling activities were carried out in the Swiss Alps around 1863 when the Swiss engineer M Leschot designed and made a tube with a diamond set face which was used in probing ahead drilling for the Mont Cenis tunnel (Figure 1). Craelius AB which today is a part of the Atlas Copco Group was formed in 1886. The name Craelius is a family name and the founder of the company was Per Anton Craelius (Figure 2). He went to the United States to study this new technology using diamonds to extract core samples and when he returned to Sweden designed his first diamond drilling machine. It was a man-powered drill needing a crew of six men, two to crank the unit, one to feed, two to power the flush pump and a foreman (Figure 3). As time passed through research and development, the original design was improved and manpower was substituted for steam engines and later combustion engines or electric motors (Figure 4). During the 1930s the drills radically changed designs and took the form of the short stroke drills which to a certain extent are still in use today. The original design of these drills have been refined during the years, hydraulic chucks, gear boxes and other improvements have been added.

Jan 1, 1995

THE power requirements of the Mount Lyell Mining and Railway Company at Queenstown, Tasmania, have, since the inception of smelting operations in June, 1,,896, been derived continuously from the extensive forests in the watershed of the Queen River, adjacent to -the works, the firewood being of good quality, mainly composed of myrtle or beech (Fagus Ounninghami), eucalypts, and manuka (Leptospermum ericoides).The country is very rugged and mountainous, indented by numerous ravines and gullies, and intersected by many creeks, which are subject to periodical floods, under the influence of a heavy and persistent rainfall. The areas so far exploited aggregate a total of about 42 sq. 'miles, and this denuded country gives promise of ultimately becoming very valuable pastoral ground for cattle-raising. The tonnage of wood yielded per acre varies from 40 to 100 tons on stack measurement of 80 cub. ft. per ton, 60 tons per acre being considered a good average yield. The gross amount of firewood handled during the past 13 years approximates 1,200,000 tons, the greater portion of which has been obtained by ordinary tramming methods. The company's main line of railway, 3-ft. 6-in. gauge, has served as a trunk line for all supplies derived from the Queen River valley, south of the reduction works, while the northern and western areas have been exploited by means of...

Jan 1, 1911

By Brinkmann J. R

The relative effects of the two basic mechanisms contributing to rock breakage during blasting, shock and gas penetration, are neither well understood nor well characterized, and need further clarification. Blasthole liner (BHL) tests separate the two effects, and by enabling direct measurement of borehole expansion give insight into the shock/gas energy partitioning in rock confinement. The hydrodynamic code DYNA2D is used to simulate the shock effect of the detonation of emulsion in a stainless steel lined hole, and the predicted expansion is compared with experiment. Workers in the past have neglected near-blasthole phenomena and have calibrated models based on stress measurements remote from the blasthole. Extrapolation back to the blasthole has inherent limitations, and indeed, one of the deficiencies of these models is that they have not been able to predict correct borehole expansions, as observed in BHL experiments. DYNA2D has been enhanced by the ICI group with a detonation model which resolves the explosive reaction zone. As a preliminary step towards the ultimate goal of devising a practical damage model, simulations are used to predict the maximum expansion that would take place if the rock were to remain undamaged. Various material parameters are investigated and it is shown that calculated liner expansions are appreciably lower than measured values for high rock yield strengths, while greater than values for low yield strengths.

Jan 1, 1990

A laminar-flow furnace technique was used to study the combustion of 37-53 µm size fraction of Woodlawn copper concentrate containing 7.4 per cent zinc, 5.0 per cent lead and 22.5 per cent copper. Factors studied included the effect of time, temperature and the distribution of volatile elements between the panicles and the fume. Air was used for most of the work but a few tests were carried out using 1 per cent oxygen in nitrogen. Chemical analysis, X-ray diffraction, and scanning electron and optical microscopy of polished sections were used to characterize the reaction products.When the concentrate was combusted at low temperatures (800-900°C), the fume was rich in lead. At higher temperatures, this was diluled by increasing amounts of zinc and copper. 70 per cent of the zinc, 60 per cent of the lead and 40 per cent of the copper were found in the fume after oxidation at 1400°C. Lead, zinc and copper were present in the fume as anglesite (PbSO4), zincite (ZnO) and cuprite (Cu2O) respectively. The major phases present in the panicles were magnetite (Fe3O4) and/or cuprospinel (CuFe2O4), with some zincite and cuprite.Elemental copper was found in the particles oxidized in 1 per cent oxygen. Possible vapour species responsible for the vaporization are discussed.

Jan 1, 1985

By Leach B. G

A geostatistical study was made of diamond drill hole intersections within 18CC stope block at the C.S.A. Mine, Cobar, N.S.W. The stope block is located in 18CC orebody which is a massive sulphide - multiple vein, Copper-Zinc type, lacking clear definition on gangue mineralogy, base-metal assays and total sulphide considerations. Of the variograms constructed for inter- section width and copper, lead and zinc grades and accumulations, only zinc displayed behaviour amenable to model fitting and kriging procedures. Zinc grades were calcu- lated for sub-blocks comprising the total stope block and comparison with equivalent grades determined by traditional methods showed them to be generally less extreme in the highest and lowest grade sub-blocks. The total-block grades derived by the two methods were almost the same. It is suggested that the failure of copper to show variogram continuity might reflect the difficulty in defining the actual 18CC orebody, a proposition which is supported by the poor continuity in the variogram of horizontal width. In the case of lead the poor continuity may be due to the frequent manner of occurrence of galena as coarse grained patches of limited extent. The results of the study, did not provide a convincing reason to depart from the traditi- onal methods of grade estimation at the C.S.A. Mine.

Jan 1, 1979

By Aziz N

The objective of the paper is to develop an understanding of the influence of caving on powered support rating by examining the geology and support performance at two sites which represent the current extremes in support rating, ie 6/240 Ton supports operating in the Hirst Seam at Solsgirth Colliery, Scotland, and 4/900 Tonne supports operating in the Bulli Seam, West Cliff Colliery, Australia. A conceptual model is introduced which considers the coal ahead of the face, the powered support, and the caved waste to be three yielding foundations which interact to control the subsidence of the roof strata. Different caving mechanisms are identified for the strata of the Hirst and Bulli Seams, ihese mechanisms being related to rock properties, ie to the palaeogeography and depositional conditions at each site, producing caved wastes with different yield characteristics. The results obtained for convergence and support reaction during production cycles at both sites are analysed to show the manner in which support reaction is developed, indicating the importance of high setting load densities in the Bulli Seam. Evaluation of the work done on the subsiding roof strata during typical production cycles by two of the yielding foundations, ie the powered support and the caved waste immediately behind the powered support, is used to further demonstrate the influence of caving mechanisms on support rating.

Jan 1, 1986

Mine closure is a legitimate element of the mining cycle and like mine development involves technical planning, permitting, and finally construction. Closure begins with the mine's operational footprint and transforms the site so that it meets the explicit requirements of the owners and regulators. Implicitly, the closure will increasingly need to meet the requirements of other interested parties such as the local community, workforce, and future land users. Golden Cross is the first modern mine closure in New Zealand. It operated for 6 + years as a mid-size gold and silver mine winning ore from both underground and open pit sources, and processing via a carbon in leach circuit including a cyanide recovery stage prior to tailings disposal. The mine is situated in a sensitive high rainfall environment, and is complicated by the existence of a large ancient landslide underlying most of the tailings dam and waste rock embankment. The regulatory process for mine closure in New Zealand is not clearly understood by operators or regulators alike. The Golden Cross mine was permitted under the Mining Act 1971 and closed primarily under the Resource Management Act. This switch of legislation, the parallel reorganisation of many government departments, and change in societal expectations with respect to long term environmental stewardship during the life of the mine resulted in the requirements of closure being significantly different to the expectations at permitting.

Jan 1, 1999

Underground measurements, observations and computed simulations, started a long time ago were concerning the study of : - occurence of typical rockburst, - inducing, stretching of main fractures in the roof of caved longwalls. They made obvious a foundamental phenomenon of inducing of strata fractures involving contact be- tween two layers quite different in their elastic characteristics : coalseam and rocklayer.. The start of primary cracks in maximum abutment zone takes place in the rock near the contact surface. It is opening of crevasses induced by traction stress component resulting of difference of rigidity of both materials and no sliding on in- terface. Occurence and stretching of these crevas- ses are a rheological phenomenon so that the rate of advance and stops of the face influence the distance between the crevasses and the stretching of these ones. The characteristics of these cracks in space and time affect mining conditions. So it is for fractures proximity and expan- sion inducing eventual blocks formation in longwall roofs in front of faces, for depth and delay of road- ways ribsides fracturing, inducing some rockbursts. In longwalls roofs, cracks initiated in front of a face can be either quite close or quite distant each from the other one, according to the depth of crushed coal in front of the face, which af- fects also extension of the cracks.

Jan 1, 1988

As this district is so far distant from the other mining centres and its mode of approach so circuitous, I am afraid that many residents of other portions of the Commonwealth never think of paying this" Australia's Silver City" a visit, to learn personally the many and various lessons everywhere available, and to become familiar with the really wonderful and interesting features and deposits (which pature has so lavishly bestowed in the mineralogical world) yet seemed to almost ignore or overlook when disposing of topogr,aphical beauties of landscape and vegetation) unless professional or business duties require their presence here. So it is to those whose life is necessarily spent in other parts of the States where they answer their call of duty, and yet feel an interest, either for business or other reasons, that my paper is specially addressed and prepared, and for that reason I witl endeavour to make my remarks more of an explanatory than a dictatorial nature. I feel sure that there. are many members of our Institute who are much more familiar, and have had many more years' experience in the various methods of timbering, filling, and ore extraction, etc., than myself, but I hope that over I6 years' experience in connection with mines and engineering works, the last six of which have been spent in Broken Hill, where, I have been very closely connected.

Jan 1, 1903

By M Wortley, A Cantarutti, T Ozkocak

The estimation of the grinding mill charge weight is vital to ensure its efficient performance. Mill underloading or overloading can cause losses through decreased production or unplanned down time. Metso Minerals Process Technology Asia Pacific and South America (MMPT) has developed two systems for measuring mill load. The first is an acoustic system (SmartEarÖ) and the second is an online model-based charge estimation system. The aim of both systems is to facilitate better operation of grinding mills. SmartEarÖ performs analysis on an audio signal from the mill and allows each different frequency component to be viewed, analysed and used in process control for load estimation. By isolating different frequencies, SmartEarÖ can give an estimate of mill load. The online dynamic mill model uses measurable mill parameters (such as power) to predict the current total load. Kalman filtering can also be utilised to further increase the accuracy of the model. Both of MetsoÆs systems have been installed at BHP BillitonÆs Cannington mine to measure the load within their autogenous (AG) mill. In this paper, the methods of mill load estimation are reviewed and compared to the bearing pressure reading, which is the current method used by Cannington to control mill load. The redundant estimates of mill load provide increased confidence and consequently more robust grinding operation under a wide range of conditions.

Jan 1, 2008

By Jones M

The concept of precise, accurate timing with Electronic Delay Detonators (EDDs) was first seriously addressed in the mid-1980s and much was made of the cheapness and profusion of digital watches in terms of the likelihood of EDDs also being cheap and easy to produce. Ten years later, with every major explosives company and many electronics groups having instituted projects to capitalise on the promise of these devices, production devices are still to come into general use. In South Africa, Expert Explosives units have been used in most applications during proving trials and more recently for production blasting in underground ring stoping and open cast coal. The outcome has been valuable learning both as to the benefits and technical requirements for electronic delay blasting, and especially, safety aspects. Examples are shown of production blasts which utilised the power of EDDs. It is evident that it is not delay accuracy alone which determines the value of these systems, but the whole robustness, flexibility and ease of delay allocation when harnessing blast engineering knowledge. Muckpile movement and shape, fragmentation and vibration frequencies have shown to be greatly influenced by designs which can be implemented no other way. The flexibility of a system and the power of the software controlling it are crucial in capitalising on blasting potential, which lies in integrating control of blast timing with other developing electronic Technologies.

Jan 1, 1995

The theory of declining optimimum cut-off grades is more than 25 years old, but for a number of reasons it is still not widely used in industry. A lack of faith in the veracity of estimated grades is not in itself a reason to abandon any attempt to optimise cut-off grades. The use of declining cut-off grades has been thought to cause high-grading, but in fact this is only true if an artificially high discount rate is used in the calculations. Perfect application of an optimum cut-off grade should ensure that only ore generating more than a minimum net return is mined, and that as much as possible of the ore capable of generating that return is mined. Therefore differing mining costs in different parts of some underground mines necessitate local modifications to cut-off grade. Optimisation of cut-off grade is of necessity an iterative process. Integration of that process into a feasibility study need not be excessively time-consuming. A number of approximations can be made to speed the optimisation (any attempt to achieve a high level of accuracy is probably doomed to failure by a lack of precise cost and price projections). A procedure is outlined for optimising cut-off grade during planning of a typical underground mine.

Jan 1, 1991