Search Documents

The nickel refinery at Yabulu consumes an average of 118,000 kg/h of low pressure steam in stripping operations to-recover ammonia and carbon dioxide from product liquor and ore tailings streams. The steam used in the stripping operations is produced from the 25 MW power generation plant at the refinery. The back pressure on the non condensing steam turbines is maintained at 60 kPa.Studies have been carried out to determine the optimum amount of steam required to be generated for stripping operations. When steam production is increased, the product liquor flow from thewashing thickeners can be increased. This results in improved washing efficiency of the thickeners and therefore improves the plant nickel recovery. A computer thickener wash model was used to predict nickel recoveries at varying steam consumption rates.The studies have shown that in most plant situations, it is not economical to-generate more steam than that already available from existing power production.The studies also highlighted the necessity to use all steam generated from power production at all times to maintain maximum nickel recovery.

Jan 1, 1985

The effects of changes in sintering bed height, coke fuel, suction and basicity on sinter productivity, physical strength and mineralogy were determined. It was found that, for a given iron ore, there is a narrow -coke range which maximises sinter strength, irrespective of bed height (in the range 300 to 500 mm) or basicity (in the range 1.2 to 2.2). Increases in bed height, at a constant coke level, improved the physical strength of the sinter. Productivity increases were obtained by increasing the sintering suction but, at coke levels other than the optimum, these *ere somewhat offset by the decrease in sinter physical strength. At basicities higher than 1.2 (i.e. 1.6, 1.8 and 2.2) there was a narrowing of'the size range of product sinter, with a decrease in the percentage of top size material, and a decrease in the amount of fines produced. Changes in coke, bed height and basicity exert major effects on sinter mineralogy, while the Nagoya index was mainly influenced by cote and bed height Changes.

Jan 1, 1975

By Lloyd C. J

The uranium markets are at present well covered by available producers. However the predicted increase in demand, recently reinforc- ed by the Arab oil crisis, will by, the early 1980s'outdistance supply. Current trends are towards light water reactors with-fast breeder reactors not expected to make any significant impact to the mid 1980s. The proposed lifting of the US embargo on the use of foreign uranium in US reactors will expand the market available to non US producers. A balancing in supply and demand worldwide will probably occur in the early 1980s. Australia's potential producers at present hold about 20 percent of the worlds U308 resources. Three companies, have contracts to supply nearly 10 900 tonnes of U308 between now and 1986 which represents about 1 percent of the predicted demand to 1986. Australian producers need to establish themselves more firmly in the market place in order that other countries will not replace us. Contracts can be written now which will allow for world market prices to be paid in the future, thus protecting the Australian producer.

Jan 1, 1974

By Abdalla MH

The deformation resulting from the presence of a tunnel may signifcantly affected, nearby structures and need to be considered during design of both tunnel and structure. The aim of this paper is to study the effect of different factors which may affect the interaction between the tunnel and the str- ucture. These include; the depth of both tunnel and foundation level of the structure ( z and t ), distance between C.L. of tunnel and loads, breadth of the loaded area, Diameter of tunnel and lining of the tunnel. The problem is studied as a two dimensional plane strain model by the boundary element technique. The results of this study indicated that the presence of a cavity/tunnel increases, in general, the vertical displacement on the ground surface and at the foundation level as well as the horizontal and vertical stresses in the cavity/tunnel level. The effect of eccentricity is increasing as e/D decreasing. For pile foundation there is a quite different- influence of the presence of cavity/tunnel in both cases of friction pile and end bearing pile type of foundation.

Jan 1, 1987

It's a great pleasure to be here today, for a whole series of reasons. First of all, when I first went to Perth back in 1972, I shortly afterwards began auditing and one of the people to pick on me when I audited the West Australian Newspaper at that time was Patrick O'Connor's father. One way to win a person across when you're auditing and getting picked on is by showing an interest in their children, so I did that and employed Patrick in our firm. In those days, conflicts of interest didn't occur. When I started Normandy, Patrick was one of the first people I went to get to work with me. He very unwisely chose to leave at one stage and you can see he's done extremely well by not staying with us. So it's lovely to have you here today, Patrick. The difference between Patrick and me, now, is that he's kept his hair, and if you're tall enough you can see I haven't.

Jan 1, 1997

The introduction of many new hydraulic ally and pneumatically powered impact breakers over the past few years demonstrates the growing interest in this technique of breaking rocklike material. The most practical method yet devised to increase the blow energy range of hammer type impactors without incurring weight penalities, is to cushion the impact of the hammer on the tool. This has been achieved in one impact breaker by means of replenisible fluid cushions between the tool and the hammer, and blow energies up to 27,000 joule (20,000 ft. lbs.) have been achieved. Impact rock breaking is becoming an important alternative to the use of explosives in the mining and the construction industry. The design of impactors is discussed and manufacturers data is presented for most of the machines now available. A review of the research and mechanics of breaking rocks with impactors is presented and the benefits of high energy impactors are discussed. The relative merits of three impactor design types are explored with regard to achieving high blow energy.

Jan 1, 1978

In August, 1975, North Broken Hill Limited announced that an intersection of 37.3 m of high grade lead-silver-zinc mineralisation, assaying 26.2 per cent Pb, 495 g/tonne Ag and 21.2 per cent Zn had been obtained at its Mine at Broken Hill, 520 m north-east of its No. 3 Shaft and slightly below the No. 36 level (1581 m). Subsequent drilling confirmed the presence of the extension of the Broken Hill Orebody on the north-western side of the Globe Vauxhall Retrograde Shear Zone and defined 1.8 million tonnes of high grade mineralisation. The area containing this mineralisation was subsequently named the Fitzpatrick Area in tribute to the late Mr. W.E. Fitzpatrick a former Member of the the Board and Manager of the Ccnpany's Broken Hill operations. This paper describes in brief the exploration programme leading up to the discovery, the general geology of the area and the proposed future exploration progranme for further extensions of the orebody within the mining leases of North Broken Hill Limited.

Jan 1, 1983

By M Kizil

Mining Engineering Degree programs have traditionally had a practical emphasis and have been highly vocational in nature. However, over the years, there has been an increasing attention to the more scientific aspects of the discipline. More recently, the professional institutions, the industry and the community at large have placed increasing emphasis on the broader aspects of the professions: management, finance, humanity, environment and social issues. Notwithstanding this, there has been a continuing emphasis on the practicalities, and most Mining Engineering programs are still strongly vocational in nature. But employers of new graduates complain about the graduatesÆ lack of practicality and readiness for employment æat the sharp endÆ on the mine site.This paper briefly describes some of the more recent developments in the Mining Engineering Degree program at the University of Queensland that attempt to address the problem. Particular attention is paid to alternative learning programs, including applications of virtual reality, practical experience at the University Experimental Mine (UQEM), and the Undergraduate Site Learning Program (USLP).

Jan 1, 2002

By Rowena C. Duckworth

The Ocean Drilling Program (ODP) is the largest international geoscience project in the world, and the state-of-the-art drill ship, the JOIDES Resolution, is permanently at sea. Each year there are six scientific cruises (legs) which each last approximately two months. These legs are designed by geoscientists from the nineteen countries that subscribe to ODP. Australia and Canada presently share ODP membership under the banner of the AUSCAN Consortium. The benefits of Australia's involvement in ODP include internationalisation of Australian geoscience, advanced graduate training, and unique scientific investigations of the ocean floors in the Australasian region. In addition, visits to Australian ports by the ODP drill ship, the JOIDES Resolution, contribute up to $2 million per visit to the local economy. Amongst the many other aspects of ten years of scientific drilling, ODP has significantly contributed to our understanding of hydrothermal processes on the seafloor. To date, three hydrothermal sites have been drilled to date by the ODP, Snakepit (MAR), Middle Valley (Juan de Fuca Ridge) and TAG (MAR). Two more hydrothermal sites are scheduled for 1996.

Jan 1, 1995

By Ricketts N. J, Smith G. D J

A hydrometallurgical process was developed for recovery of copper from copper-lead matte formed as an intermediate product at the BHAS lead smelter at Port Pirie. A plant utilizing this process was commissioned in 1984. The leach step involves oxidation of the copper-lead matte in an oxygenated acidic chloride-sulphate leachant. The results of laboratory scale testwork from which the chemistry of leaching was deduced, are presented in this paper. The rate of recovery of copper to solution from copper-lead matte depends largely_on the availability of oxygen to the sulphide surface. The optimum leach temperature is approximately 85¦C. Free acid must be supplied according to the stoichiometry of the leach reaction: Cu1.91 S + PbS + 2.91 H2SO4 + 1.455 02 = 1.91 Cu2+ + 1.91 SOj- + PbSO4(s) + 2.91 H2O + S¦ The grind size of the matte is of minor significance. Chloride concentration in leachant should be at or above a minimum of 10.0 g/l. Chloride acts to complex cuprous ions formed during leaching.

Jan 1, 1987

The Black Star lead and zinc ore-bodies, situated in the western zone of mineralisation at Mount Isa occupy an area 2000 ft. long with varying widths from 100 ft. to 300 ft. The strike is N5°W, and the average dip 60° West.To test at depth the potentialities of this area, an extensive diamond drilling campaign was commenced on 16th October 1927. It was continued, with from one to six machines working, until the end of 1931. During this period, 26 inclined holes, with an average depth of 1224 ft, and a total footage of 31,828 ft. were completed. A vertical hole, 2452 ft. deep, for comparative purposes, has been omitted.These drilling operations came directly under the charge of G J Gray, General Superintendent of Mount Isa Mines, and, in the early stages were supervised by E. D. McDermott, of the Mining Trust, London. The foremen, who were in charge of various sections of the drilling operations, were: H Vale, F Bray, J Winston and A A Sanstedt.

Jan 1, 1932

By Fisher AEJ

On Sunday morning 7th November, 1976, at approximately 2-25 a.m., smoke was discovered issuing from the 1912 m long belt drift at Appin Colliery. A Clouth steel cord rubber belt approximately 940 mm in width had been installed in the drift in 1963 on the basis that no fire resistant steel cord belt was then available to operate on a single lift at the load and on the 160 gradient of the drift. Investigation showed that the belt drift was on fire and the usually downcasting drift was upcasting. Immediate fire fighting and rescue operations were instituted and the drift was sealed off. High expansion foam was pushed into the drift from the surface and the fire was brought under control. Recovery work resulted in the fire being put out and the drift open for walking traffic by, S-P0 am., on Wednesday 10th November, 1976. lie experience gained during the fire fighting and recovery operations led to recommendations in regard to future use of high expansion foam.

Jan 1, 1981

By R H. Eric

Surface wave formation induced by a high-strength submerged jet in a bottom blown metallurgical vessels has been studied experimentally by using one-seventh water model of CLU (Creusot-Loire Uddeholm) reactor with two different tuyere configurations. Experimental results have been discussed in terms of the wave period, wave frequency and wave amplitude with respect to air injection rate and tuyere configuration at a 0.23 m bath height. The results from high speed photography observations displayed the formation of rotating surface waves which circulates within the water model. It was found that the frequency and the amplitude increased with gas injection rate. The wave period for off-centre nozzle orientation was found to be lower than those of the centre configuration. The experimental results also showed that the frequency of a rotating wave increases when the tuyere orientation becomes off-centred . The predicted amplitudes were in very good agreement with the experimental values over a range of gas flowrates between 0.00599m 3/s to 0.01081 m 3/s.

Jan 1, 2000

In-pit crushing systems have been known in the mining industry for many decades. The question whether in-pit crushing is a viable option has often been asked. More than 200 mobile and semi mobile crushing systems have been installed worldwide at various locations and applications. Economic pressures have forced mine operators to reconsider the use of a conventional truck-shovel operation and have contributed enormously to the development of in-pit crushing and conveying systems. The in-pit crushing concepts have varying mobility capabilities. These range from fixed, stationary crushing plants to semi-mobile and fully mobile crushing plants. All these systems are operated in connection with a conveying system. In general in-pit crushing systems have technical and economical cost advantages over truck-shovel operation, particularly as mine capacities increase and mines become deeper. The integration of an in-pit crushing system represents a significant up-front capital investment and the mine is only able to depreciate the capital investment over a sufficient mine life including plant capacity to realise the benefit of the much lower operating cost.

Jan 1, 2003

By P D. Fraser

This paper examines the new water-hydraulic (hydro powered) drill rigs that have been developed and proven in the last decade primarily in tabular, shallow-dipping, narrow-reef, hard-rock South African mines. These include - drill rigs for flat end tunnel development, narrow inclined raises and winzes, large inclines and declines and long hole based developments such as orepasses and vent raises. The hydropower technology rigs offer advantages both in safety and performance over traditional compressed air powered, hand-held development are generally more cost effective than imported oil electro-hydraulic drill rigs. Furthermore, hydro powered rigs are inherently energy efficient. The benefits of hydropower are discussed and a æcomprehensive development modelÆ is presented which demonstrates that orebodies can be accessed in significantly shorter times. æLocalisedÆ half level hydropower systems are introduced and a range of ancillary equipment available is listed.CITATION:Fraser, P D, 2012. The use of high-pressure, water-hydraulic (hydropower) technology in South African narrow-reef, hard-rock mines, in Proceedings Narrow Vein Mining 2012 , pp 229-236 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By Eaton R. A

The design of most underground mining machines shows little evidence of regard for ergonomic principles and operator comfort. Likewise, efficiency and ease of operation often appear to have been given little consideration in machines where ruggedness and simplicity have tended to dictate the configuration. Improvements in productivity are amongst the benefits to be gained by a different approach to machine design. The paper describes the philosophy and features of a test bed Load-Haul-Dump Vehicle undergoing trials at Mount Isa Mines. This machine is the outcome of a Research and Development Programme conducted by the Department of Mechanical Engineering at the University of Queensland and Mount Isa Mines Limited. The diesel powered test bed features an enclosed, air conditioned cabin, with a suspended operator's control station and electrically operated controls. An electronically controlled hydrostatic transmission incorporating wheel slip control, is another innovation. The performance and operator acceptance of the machine has led to adoption of most of the concepts in a new machine now being put into production.

Jan 1, 1987

By Koginmo V. I

The concentrator at Bougainville Copper Limited has an annual throughput of 48.2 million tonnes/year producing approximately 175,000 tonnes copper, 16.1 tonnes gold, and 50 tonnes silver. Conventional three stage crushing and screening are used to reduce run of mine ore to an average product d80 size of 6.7mm. The primary objective of the crush- ing plant is to provide a continuous supply of ore to the 12 primary grind- ing mills via an intermediate 300,000 tonnes capacity stockpile. Since ball mill performance improves with decreasing mill feed size, the crushing plant continually strives to produce the finest possible product for mill- ing. This has been achieved by increasing plant availability and total installed power, and improving crusher manganese liner life, screen cloth life, and plant operating practices. A recent innovation was the installa- tion of a 35 million tonnes/year preconcentration screening plant in Janu- ary 1987 to recover high grade fines from low grade run of mine ore types in which the mineralisation occurs preferentially along fracture planes in the parent rock.

Jan 1, 1988

By Joussemet R, Fabre F

The paragenesis of the Escuzar Mine (Andalusia-Spain) comprises: ò major constituents: celestite and carbonated minerals (abundant calcite and less frequent strontianite). ò minor constituents: sulphates (gypsum and anhydrite), clays and some iron oxides and hydroxides. The average content is at about 60 per cent SrSO4. Since liberation size was fine (from 30 to 50 ¦m), the flotation method was chosen. Laboratory batch tests have shown the relevance of using alkylsulphates with as long as possible hydrocarbon chains. The recovery obtained led to an expected 95 per cent SrSO4 concentrate with nearly 70 per cent recovery. Pilot plant tests (160 kg/h) have confirmed these results and attained a recovery of more than 65 per cent of a 96 per cent SrSO4 concentrate. Extrapolation to the industrial scale (14 t/h) has been successfully carried out : up to 600 t of a concentrate at more than 95 per cent SrSO4 has been obtained. Non optimised recovery has already reached 60 per cent for a 97 per cent SrSo4 concentrate.

Jan 1, 1993

By T J. Scanlon

Heavy minerals recovered from recently discovered deposits in the Murray Basin are proving to be somewhat more difficult to process into saleable ilmenite products than ilmenites from existing operations. This is due to the nature of the gangue minerals present, the impurities in the valuable minerals and the size distribution of the mineral assemblages. Ilmenite product quality, in particular, can be adversely affected by any of these factors. Over the past two years the authors have been involved in assessing the potential to manufacture ilmenite products from a variety of mineral sand deposits in the Murray Basin. The steps undertaken to define the potential products and develop suitable flowsheets have evolved in parallel to the exploration efforts, in cooperation with companies undertaking exploration in the Murray Basin. A combination of an understanding of detailed mineralogy, application of magnetic fractionation and modification of magnetic susceptibility of the ilmenites has in all cases, been successful in improving ilmenite product quality. The targeting of particular ilmenites to specific downstream processes for TiO2 pigment manufacture is the most challenging aspect of this development.

Jan 1, 2001

A major problem in the continuous casting of aluminium killed strip steel is the incidence of black and grey lines in the strip surface caused by the alumina inclusions. One place for limiting the number of alumina inclusions is by providing favourable fluid flow conditions in the ladle so that the inclusions float out to the surface or adhere to the ladle wall. In laboratory equipment 20 kg of steel was melted in an alumina crucible of 14 cm diameter in an induction furnace. Deoxidation was carried out while the melt was constantly stirred by argon bubbling. Bubble frequencies were measured at the lance tip using a microphone technique. High speed cine photo- graphy was incorporated to measure melt top surface velocities. Experimental results indicate that the rate of removal of inclusions is a function of both the gas input and the power input. However due to unfavourable surface area to volume ratio, reoxidation of the melt took place. Some other experimental difficulties in working at high temperatures are also discussed such as lance design, melting arrangement and sampling techniques.

Jan 1, 1984