Search Documents

By M Darvall And R Fare, D Dormer

The Argo Archaean lode gold deposit is hosted within a structurally complex shear zone system, 70 km south of Kalgoorlie, and 3 km west of the crustal-scale Boulder û Lefroy Fault. Argo is an active underground mine currently producing at a rate of 120 koz pa with a Probable and Proven Reserve as at December 2005 of 2.19 Mt at 5.94 g/t Au (419 koz), a reduction on the December 2004 Probable and Proven Reserve of 4.58 Mt at 5.74 g/t Au (845 koz). This Reserve is hosted in six separate gold bearing lodes within the Argo shear system. Presently, a further six subeconomic shears are recognised. The 2005 Reserve figure represents a reduction of 426 koz compared to the 2004 Reserve as a result of a thorough review of the geological interpretation/resource model, and engineering factors applied to the Resource/Reserve, and depletion due to mining. Year on year Resource/Reserve figures at Argo had gradually increased as additional information on the system became available and mining methods were increasingly resolved with early production. The portal for Argo underground mine was cut in June 2002 within the highly profitable Argo open pit. The proposed æAvocaÆ bottom-up mining method required extensive lead time between development and the commencement of stoping in April 2004. During development considerable additional complexity in the Resource was encountered. Additional structures were identified, and complex splay interactions affecting the geology impacted on development. Intensive concurrent exploration in the footwall to the main lode during this period was the main cause of the increase in the Resource/Reserve figures during early development. As development progressed, lower grade continuity was observed than was previously interpreted. At the same time, drilling of deeper portions of the deposit and subsequent reinterpretation of the geological model significantly reduced strike lengths of economic mineralisation. Radical changes to the mining methods were required to improve productivities and to satisfy geotechnical considerations. The changes altered the engineering factors applied, which resulted in a reduction in the Reserve figures.

Jan 1, 2006

By Van Deventer J S J

The first step in the design of a process to treat a possible economic precious metal deposit should be an examination of the mineralogy of the ore. Using this and other initial tests, the extractive metallurgist can design a process to treat the ore. In the field of precious metal metallurgy, little emphasis is placed on the mineralogical information available to the metallurgist. The information is of far more use to the geologist and the mining engineer. Diagnostic leaching was designed to open up the field of mineralogical analysis to the metallurgist. When a mineralogist looks at the deportment of gold in an ore, he is usually looking for an element which is present in parts per million, so that errors in sampling are multiplied dramatically. Diagnostic leaching offers a cheap, simple, practical alternative. In order to determine with which minerals the desired precious metal is associated, a specific mineral is first eliminated using a selective oxidative leach, and cyanidation is used to extract the precious metal (in this case gold and silver) liberated by the destruction of this mineral. The precious metal extracted can be measured in solution to give a fairly accurate record of the amount of the precious metal associated with that mineral. Furthermore, the residue from this first stage can be subjected to another selective acid leach, and the process repeated. The procedure can be varied to suit the mineralogy of the matrix material. At the end of this diagnostic leach the metallurgist is left with a complete record of the deportment of the precious metal. He can now use this information to design a metallurgical flowsheet to treat the ore. Diagnostic leaching is thus an analytical tool which can be used by the metallurgist not only to examine new ores, but also to look at problems occurring at existing plants. The procedure is not only limited to ores and residues but in fact can deal with any type of intermediary product that occurs on a plant. The information gained from analysing an intermediary product can give a useful indication of how well a unit process is working, eg flotation, roasting, etc.

Jan 1, 1992

By Case JE

Complete Bouguer and isostatic anomaly maps compiled for Costa Rica provide new insights into the crustal structure and mineralization. Terrain corrections were approximated from the station to a radial distance of 167 km by computer using a 3- minute digital elevation model of Costa Rica and surrounding areas. Isostatic corrections, based on Airy-Heiskanen compensation, were also calculated from 0 to 167 km using the 3- minute elevation model and from 167 km to 180 degrees using combined topographic and isostatic reduction maps. Costa Rica can be divided into four main terranes based on gravity data: a Pacific coastal region, a Pacific inland area, a central region, and a Caribbean coastal region. Negative gravity anomalies along the Pacific coastal margin correlate with an offshore sedimentary basin, and large positive anomalies correlate with mafic and ultramafic igneous rocks on the Santa Elena, Nicoya, and Osa Peninsulas, and at Puerto Quepos. Pacific inland anomalies are separated from the Pacific coastal region by a steep gravity gradient, and over the Coast Ranges a major gravity low overlies a thick section of low- density sedimentary rocks. In the central region, a major gravity low occurs over a thick low-density Quaternary volcanic complex in the Cordillera Central, north of San Jose. A prominent feature of the Caribbean coastal region is an interrupted gravity low over the Limon Basin that reflects a thickening of low-density sedimentary rocks. A conspicuous gravity lineament, trending northeast separates northern and southern Costa Rica. The lineament is defined by the termination of several major gravity anomalies including those over the Coast Ranges, Cordillera Central, Puerto Quepos, and Limon Basin. In addition, the lineament correlates with other geological and geophysical data including: northeast-trending faults, the southern limit of large Quaternary volcanoes, the segmentation of the middle America volcanic belt, and a seismicity gap. This lineament may be the expression of a previously unrecognized major northeast- trending fracture zone in central Costa Rica. An important economic implication of the gravity lineament is a correlation with the termination of gold and porphyry copper deposits in Costa Rica.

Jan 1, 1987

By Mudge S. T

Tin mineralisation occurs at Renison Bell, near Zeehan in Tasmania, as a group of cassiterite-bearing massive pyrrhotite bodies in Cambrian sedimentary rocks. Mineralising fluids from the underlying Pine Hill Granite have replaced carbonate rocks with massive sulphides and cassiterite. The discrete blocks of massive pyrrhotite have high density and high magnetic susceptibility contrasts with the comparatively barren country rock. They are strongly remanently magnetised and are excellent geophysical targets. A detailed geophysical model of the mine was created from a database comprising 1:2500 scale geological mapping and geological logs of approximately 4000 drill-cores. The model comprises 93 parallel cross-sections, each 1.5 km long, spaced 20 m apart. Each cross-section is comprised of up to 150 polygons which represent all known individual rock types and orebodies. The magnetic response of the model was computed and the residual between the model and the observed response, measured by a low-level helicopter magnetic survey, revealed several anomalies unaccounted for by the model. Drill testing of these anomalies led to the discovery of several hitherto unknown massive sulphide occurrences. Surface gravity data of the mine and surrounding district were enhanced by applying digital terrain corrections. The corrected Bouguer anomaly revealed a hitherto unknown positive anomaly associated with the ore zones of the Renison mine. The gravity anomaly of the model was also computed. Unfortunately, the limited resolution of the observed data prevented the delineation of ore targets. The terrain-corrected Bouguer gravity data were also used to model the shape of the underlying non-magnetic Pine Hill Granite. A computer inversion method was implemented to build a 3D block model of the granite. Results agreed with previous conventional 3D modelling techniques but yielded improved resolution of the granite form. The project involved development of new computer software to build and edit the large and complex 3D geophysical model of the mine and to compute the model's magnetic and gravity responses. Software was also developed to build and compute the gravity response of a 3D block model of the underlying granite.

Jan 1, 1997

By Schiller J. C, Both R. A

Base metal mineralisation occurs at several locations within the regionally metamorphosed Kanmantoo Group on the southeastern flank of the Mount Lofty Ranges between Kanmantoo and Strathalbyn, 50 km southeast of Adelaide. Sulphide mineralisation is of three main types (Seccombe et al, 1985):1. copper deposits, at the Kanmantoo and Bremer mines, South Hill prospect and several minor occurrences,2. lead-zinc deposits at Aclare, Wheal Ellen, Strathalbyn, St. Ives, Scott's Creek, and Glenalbyn mines,3. pyrite-pyrrhotite mineralisation of the Nairne pyrite deposit and many other pyritic schist units within the Kanmantoo Group.Syntheses of folding, metamorphism and stratigraphy of the Kanmantoo Group were given by Kleeman and Skinner (1958), Offler (1960, 1963), Offler and Fleming (1968), Marlow (1975), Mancktelow (1979) and Parker (1986). Studies of the general relationships of mineralisation to structure in the Kanmantoo area were given by Grasso and McManus (1954), Mirams (1962), Poole (1969), and Lindqvist (1969).Several conflicting views on the origin of mineralisation in the Kanmantoo Group have been proposed. Thomson (1975) considered much of the mineralisation as a late-stage product of regional metamorphism and he, like Parker (1986) and Lambert et al (1987), stressed the importance of major lineaments as an ore control. However, Lindqvist (1969) and Verwoerd and Cleghorn (1975) tentatively suggested a syn-sedimentary origin to the Kanmantoo copper deposit and Jensen and Whittle (1969) and Seccombe et al. (1985) on the basis of sulphur isotope data proposed a bacteriogenic sulphur source and a sedimentary origin for sulphides in the Nairne pyrite deposit. The latter suggested that most copper deposits represent stockwork, vein or disseminated zones within subsurface vents whereas massive mineralisation at Wheal Ellen and Aclare mines probably accumulated on the ocean floor.This paper presents new geological information on the structural and metamorphic setting of the base metal deposits and attemptsto relate this information to previous regional studies of the Kanmantoo Group. Estimates of pressure and temperatureof peak metamorphic conditions based on silicate mineral stabilities are considered in relation to various silicate and sulphidegeothermometers which have not previously been applied to rocks in the Kanmantoo Group.

Jan 1, 1988

By Allnutt S. L, Carswell J. T, Mutton A. J

The Dugald River Zn-Pb-Ag deposit occurs within the complexly deformed and metamorphosed sediments of the Middle Proterozoic Cloncurry Terrane, Eastern Succession, Mount Isa Inlier. The sedimentary sequence comprises a thick package of variably carbonatic argillitic and siliciclastic sediments of the Corella Formation, Lady Clayre Dolomite and Knapdale Quartzite. A slate and calc-argillite unit locally referred to as the Dugald River Slates is the host to the economically significant deposit. The deformational history of the Dugald River area involved three phases of ductile deformation. The present geometry of the Dugald River Main Lode is recognised as a strike extensive steep westerly dipping tabular sheet, within which a steep north westerly plunging zone of pronounced thickening is evident. This zone is interpreted to have formed during folding via remobilisation of the sulphides into a shoot-like body, the geometry of which was controlled by stretching associated with the folding. Further modification of the shoot and sulphide re-distribution has resulted from late phase transgressive shears. The sulphide mineralisation is characterised by three distinctive sulphide types, laminated, banded and breccia, the distribution of which define two broad zones. The northern zone is a narrow I - 5 m thick stratabound unit comprising finely laminated and banded sulphide mineralisation within a well bedded fine grained argillite sequence. This is part of the Lady Clayre Dolomite sequence and is a predeformational precursor form of mineralisation. The southern zone comprises the thickest development of mineralisation (up to 30 m) characterised by slate-sulphide breccias and veins derived from complex polyphase remobilisation of the sulphide mineralisation. It is this zone which forms a stratabound locally transgressive body within the high strain Dugald River Slates and which contains the main body of economic mineralisation. Sulphide mineralogy comprises sphalerite, pyrite, pyrrhotite, galena and traces of chalcopyrite, pyrargyrite, tetrahedrite, marcasite and arsenopyrite. The present resource for the Dugald River deposit stands at 38 Mt grading 13.0 per cent Zn, 2.1 per cent Pb and 42 g/t AS. The Dugald River Zn-Pb-Ag deposit is regarded as an example of a syndiagenetic stratabound sulphide accumulation which, as the result of polyphase deformation and upper greenschist to middle amphibolite facies metamorphism, has undergone extensive remobilisation and Rccrystallisation.

Jan 1, 1993

By D Wiseman, R Dunne

Flash flotation is a process that is included in many new mineral processing plants as part of the grinding circuit. Some of the valuable minerals can often be liberated at coarse sizes and will remain in the recirculating loads of the mill until they are reground small enough to report to the cyclone overflow. In addition, minerals of high density report to the cyclone underflow despite being fine in size. This can lead to overgrinding and makes the recovery of valuable fines by flotation difficult. Flash flotation is used to remove the readily floated coarse particles as early as possible and can therefore prevent overgrinding. It thus has the added potential to improve materials handling of the concentrates in such processes as filtration. The merits of including flash flotation within an integrated comminution-conventional flotation circuit is not easy to determine experimentally. Simple batch flotation tests are unable to provide any measure of the possible or probable improvements that are likely to occur from this circuit configuration. As a consequence expensive pilot plant programs are resorted to, to provide the information that will justify the inclusion of flash flotation into a comminution-flotation circuit. Those who have been involved in such pilot plant programs will know of the difficulty in stabilising the circuit as well as selecting the appropriate operating parameters (eg amount of concentrate to be removed in both the flash flotation and conventional flotation circuits). The interactive nature of this circuit (grinding, classification and flotation) is the root cause of these difficulties. Computer simulation, based on information derived from laboratory batch test work or plant and laboratory data, offers an alternative means by which an initial assessment of the merits of a flash flotation circuit can be determined. It can also provide the basis and focus for pilot plant testwork. Recently MacKinnon, Yan and Dunne (2003) developed a model that allows the performance of a flash flotation to be obtained within a closed circuit grinding operation. This paper provides details of an extension of this model to incorporate the interaction of flash flotation on the downstream conventional flotation circuit and allows æwhat ifÆ scenarios to be explored. Details of the laboratory batch test work methodology and the pertinent data derived from these tests that are used in the models and simulation are provided.

Jan 1, 2005

By Davey KJ

Complex sulphide ores are characterised by complex texture of the valuable minerals. Any assessment of the performance of differential flotation circuits treating such ore should include analysis of the effects of poor liberation of the valuable minerals. Selected samples were taken from balanced size by size surveys of the flotation section of a concentrator treating an ore body containing fine grained galena and sphalerite in a matrix of iron sulphides which is mostly pyrite. liberation measurements were made using the QEM*SEM system on four or seven size fractions. The measurements indicated that less than 40 per cent of the galena and less than 60 per cent of the sphalerite in the flotation feed was liberated. The final concentrates were largely composed of composites of valuable minerals and iron sulphide however there was a small but significant fraction of liberated iron sulphide. Using the sized mineral flows obtained from the original balances and the liberation measurements, a satisfactory liberation balance was obtained. This enabled the effect of liberation on the flotation performance to be examined; not only for the entire circuit but also in the rougher, scavenger and cleaning sections. In the zinc circuit the effect of a regrind mill could be assessed. Recovery of galena in the lead circuit was limited by the recovery of composite lead particles. Recovery of liberated galena exceeded 95 per cent in all size fractions while the recovery of composite galena exceeded 85 per cent below 38 ¦m but fell sharply above 38 ¦m. Examination of the behaviour of the liberated and composite galena in the various sections of the lead flotation circuit revealed high recoveries of both liberated and composite galena particles in the roughing and scavenging sections but very low recoveries in the final two cleaning stages. Similar trends to those observed in the lead circuit applied in the zinc circuit although the performance of the liberated sphalerite also fell off at sizes greater than 38 pm in this case. Thus the zinc recovery was limited by the flotation of both the liberated and the composite sphalerite. The effect of regrinding was to increase the recovery of sphalerite mainly by reducing the amounts of sphalerite in less liberated sizes rather than by increasing the liberation of the sphalerite within a given size Fraction.

Jan 1, 1993

By C J. Ptacek, J G. Bain, D W. Blowes

The passive interception and in situ treatment of groundwater using permeable reactive barriers (PRBs) has, within the past decade, become an accepted remedial approach to the control of plumes containing dissolved organic and inorganic contaminants. Since the first applications of the technology in the early-1990s, there have been several field-scale PRBs that have provided excellent treatment of dissolved metals in groundwater. Additional commercial applications and demonstration projects continue to be developed. Three field-scale applications and supporting laboratory columns have shown that several thousands of milligrams per litre of sulfate, more than 1000 mg/L iron, and several tens of milligrams per litre of other metals can be removed from groundwater by PRBs that promote sulfate reduction. The reactive materials, which incorporate various forms of organic carbon, promote microbially mediated sulfate reduction, the generation of hydrogen sulfide, and the subsequent precipitation of sparingly soluble iron and other metal sulfide minerals. Effective performance has been achieved by PRBs installed at a mine-tailings impoundment in 1995 (Sudbury, Ontario) and at an industrial facility (Vancouver, British Columbia). These PRBs have removed iron and other metals from groundwater. Similar materials were also used to create reactive layers within test cells directly in a tailings impoundment in 1999 (Timmins, Ontario) with the objective of removing iron and sulfate from the pore water before it migrates from the tailings impoundment. Zero-valent iron (ZVI) has been shown to provide excellent removal of chromium (VI) in a PRB, which was installed at the US Coast Guard facility in Elizabeth City in 1996, by reduction and precipitation reactions. Laboratory tests have also shown that ZVI reduces As(V) to As(III), which is subsequently removed from solution by co-precipitation with iron oxyhydroxides. In groundwater containing sulfate, ZVI and mixtures containing organic carbon can promote sulfate reduction and the subsequent precipitation of sparingly soluble arsenic and other metal sulfides. A trial PRB system was installed in 2001 and was shown to attenuate arsenic and other electroactive metals in groundwater at an industrial facility in northwestern Ontario. Basic oxygen furnace (BOF) slag, a waste material generated by the steel industry, has shown excellent potential for the removal of phosphate, elements such as arsenic and water-borne pathogens from groundwater in field and laboratory tests.

Jan 1, 2003

By K S. Smith, B P. Jackson, P J. Lamothe

The upper Arkansas River south of Leadville, Colorado, USA, contains deposits of fluvial tailings from historical mining operations in the Leadville area. These deposits are possible non-point sources of acid and metal contamination to surface- and ground-water systems. We used stable-metal isotopes to help ascertain metal retention and release mechanisms that influence metal transport from the deposits to shallow ground-water systems. To accomplish this, we excavated an intact core from a small fluvial tailings deposit and performed laboratory column experiments to examine the amount of metals leaching through the core. Deionised water was continuously applied to the top of the core, and effluent was collected from the bottom of the core for a period of about two months. Three saturation conditions were used, including unsaturated, partially saturated, and fully saturated. Reducing conditions developed upon partial and complete saturation of the core. During the unsaturated leaching phase, core effluents were acidic (pH 2.8 - 3.5) and contained elevated metal concentrations. During a portion of the unsaturated leaching phase, stable-metal isotope spikes and conservative tracers were simultaneously applied to the top of the core. The isotopes provide a means to delineate metal behaviour within the core. During the unsaturated leaching phase, the isotope spikes did not exhibit breakthrough with simultaneously added conservative tracers. However, some of the stable-metal isotope spikes did break through when reducing conditions occurred in the core (during the partial- and completesaturation conditions). In this paper, we use Cd as an example of the utility of stable-metal isotopes in geochemical studies. In the case of Cd, after the core was partially saturated, the 111Cd spike was released as evidenced by a change in the Cd isotope ratios in the effluent. This release continued during the fully saturated leaching phase, however, the total Cd concentration did not increase. These results suggest that the 111Cd spike was retained inside the core during the unsaturated leaching phase, and only partially released as reducing conditions developed. Results from this core-leaching experiment indicate there is a large reservoir of water-soluble material within the fluvial tailings deposit, which yields elevated metal concentrations and high acidity, and which may degrade adjacent ground- and surface-water quality. Use of stable metal isotopes in this study facilitated the determination of different metal-retention processes, metal-release processes, and metal sources in the fluvial tailings deposit in response to changing geochemical conditions.

Jan 1, 2003

By J Player

Big Bell Mine started experiencing relatively large mining related seismic events, and accompanying rockbursts, from February 1999. Twelve rockbursts damaged access development from February 1999 to June 2000, with severe damage extending for up to 100 m along footwall drives. Five seismic events associated with the rockbursts were recorded by the AGSO, measuring 1.9, 2.2, 1.7, 2.4 and 2.2 on the Richter scale. These events affected 485 and 460 footwall drives in August and November 1999 and 535 footwall drive in June 2000 (drive level nomenclature is equivalent to the depth below surface and RL). After the third event (July 1999) it was apparent that the seismicity was not a once-off phenomenon. This (sudden) onset of seismicity required management to implement a series of precautionary measures:to ensure the safety of the workforce, to maintain continuity of production, and to reduce rockburst damage rehabilitation. The measures included extended re-entry periods and exclusion zones in high-risk areas, improved rockburst resistant support systems in areas prone to damaging seismic activity and improved support systems in areas prone to shakedown damage. A full-scale minewide ISS seismic system was ordered in October 1999 and commissioned in February 2000. A portable eight-channel CSIR-Miningtek system was installed at short notice as an interim measure in August 1999. This CSIR system covered the northern producing stopes, where the majority of the rockbursts had occurred. The objective of the seismic monitoring was to monitor relative activity and to determine trends with regards to time and location. MAP3D numerical modelling was used to investigate the relationship between seismicity and various combinations of stress components to assess the relative seismic risk in both current and proposed working areas. This information is used to determine where and at what stage in the mining cycle the rockburst resistant support is required. Analysis of the seismicity has determined two distinct modes of seismicity û small-scale localised, high frequency events in high stress areas and larger events related to shear along previously intact foliation surfaces. This paper includes a summary of the seismic history, seismic data analysis, support system design, mine design adjustments and management action to minimise the effects of seismic activity at Big Bell Mine.

Jan 1, 2000

By Hang G, Hongtian X

In this paper, it is briefly introduced that China's Ordovician limestone confined-water menaces coal mining and Ordovician water is prevented and cured to secure the safety of coal mining. The theory of "Down-Three-Zones" is presented on the basis of research and practice in recent ten years. The concept of "Down-Three-Zones" of floor water-eruption is described clearly. Finally, the principle and method of applying the theory of "Down-Three-Zones" are discussed. 1. An Introduction of Damage: China is rich in coal resources. The conditions of coal field geology are quite complicated. There is an area of two million square kilometre of Karst limestone in nine million six thousand square kilometres of territory. The resources of underground water are rather plentiful, but this menaces coal exploration. Sixty percent of coal mines in China are damaged by limestone confined-water in different scales, particularly coal mines located the Carboniferous-Permian coal fields of the Ordovician limestone distribution area of Northern China. Because there is the 500-800 metre thickness of Ordovocian limestone and the well developed Karst containsl plentiful water, Karst water can have more than 100 Kg/cm pressure. Limestone aquifers have only distances of several metres or several decade metres to coal seam, Karst water can enter the aquituge and even the coal seam, large eruptions often occur. For example, a mine of 3 million ton production capacity had an eruption of 2053 cubic metres per minute. This is the largest confined-water eruption which has brought enormous economic damage and threatened the safe production of coal mining. Therefore, the prevention and cure of Ordovician water has immense advantage to the development of the coal industry. There are several decades experience in the prevention of Ordovician water-eruption in China. The prevention of Ordovician water-eruption has two kinds of plans. 1) dewatering and depression: it refers to dewatering of aquifers as roofs of seam and depression of aquifers as floors of seam in mining areas. 2) comprehensive prevention under the condition of having water pressure in aquiters. Due to enormous water, electricity, equipment and lots of other factors, the former isn't used extensively, the latter tits to China's actual conditions and is used widely. So-called comprehensive prevention under the condition of

Jan 1, 1988

Interpreted geologic domains provide the geologic architecture of many current models used to estimate the potential economic resources in mineral deposits. The spatial extent of each domain is usually defined by a three-dimensional wireframe or triangulated surface.The set of geologic wireframes forming part of a resource model might generally be called a spatial interpretation of some set of geologic features coincident with the mineralisation, based primarily on logged and mapped properties of the samples and other exposures of the mineralisation. The interpreted spatial distribution of rock type, alteration and grade of drill hole samples above a particular grade threshold are commonly used criteria in constructing the geologic domain wireframes. Frequently, the grade threshold is closely related to the anticipated economic cut-off grade. The boundaries or spatial limits of different domains are most commonly defined as æhardÆ or æsoftÆ. A æhardÆ boundary usually means no dependent relationship of any kind is defined between the properties of samples inside a particular domain wireframe and those samples outside the wireframe. A æsoftÆ boundary commonly implies that some kind of dependent relationship does prevail between the properties of samples inside and outside the particular wireframe. Many ways are used to describe those relationships, few of which are based on spatial analysis of the continuity of sample attributes across the domain boundaries. In local estimation procedures such as ordinary block kriging, æhardÆ boundaries act as a total barrier to the influence of samples on either side of the boundary depending on the location of the block being estimated. In some instances, æsemi-permeableÆ boundaries are used in which the samples inside a domain wireframe are allowed to influence the estimates outside but not the reverse. This can lead to many undesirable effects in estimates of block grades.This paper discusses the value of this approach to geologic domaining from a viewpoint of model complexity, as well as in relation to the implications for both linear and non-linear estimation methods and contrasts it with alternatives. It also explores some important consequences of using æhardÆ and æsoftÆ geological boundaries with the commonly used modelling methods: excessive smoothing of estimates near domain boundaries and conditionally biased estimates of grade at the global and local scale.

Sep 26, 2011

By T Roache, K Yang, M Quigley, C Young

In late 2004 a large-scale evaluation of a new suite of tools for semi-automated core logging was carried out in the Eastern Goldfields of Western Australia. Known as HyLoggingÖ Systems, these combine rapid hyperspectral mapping of mineralogy and very high resolution digital imaging of cores and chips in their original containers. The resulting data is very information-rich and provides information about host rock, alteration and regolith mineralogy. This, in turn, can be used to test geological models about fluid/rock interactions, ore system architecture, ore feed characterisation and generally improve the objectivity of the normally manual and variable logging process. Results were obtained from the Kanowna Belle and St Ives gold deposits in the Kalgoorlie region, as well as numerous holes from across Western Australia stored in the Kalgoorlie Core Library. At the Kanowna Belle gold deposit critical spatial trends in the proportions of white mica, the chemistry and species of those micas, the presence of selected carbonate species and the absence of chlorite proximal to ore zones have all contributed to improved ore deposit understanding. Significantly many of these trends are not discernible to the naked eye, nor easily quantified, previously, across many thousands of metres of core from separate drill holes. At St Ives, the HyLoggerÖ was able to show that low-Al (phengite) and high-Al (paragonite to muscovite) white micas are spatially associated with D3 foliation zones that are proximal and distal to Au mineralisation, respectively. D3 foliation zones are also associated with the depletion of metamorphic chlorite and amphibole, and their replacement with biotite, relative to unaltered mafic host-rocks. The HyLogged GSWA drill holes yielded mineralogical characterisation of classic deposits, including Kambalda (Ni), Fimiston (Au), Teutonic Bore (Cu, Zn, Ag), Black Swan (Ni) and Hannans (Au), illustrating a wide variety of mineralogical trends due to both host lithologies, previously unrecorded lithological subdivisions, and alteration patterns. During 2005 a unique thermal infrared HyLogger was developed to map the important remaining silicates, such as feldspars, quartz, olivines, pyroxenes and garnets. This was successfully tested on a 9000 m subset of the same cores as the earlier study. Interpretation has focused, in particular, on silicification, albitisation, and the mineralogy of several high-grade, less hydrous deposits.

Jan 1, 2006

By J D. Bryant

The Ernest Henry Copper-Gold mine, the third largest copper deposit in Australia, is located 35 km NE of Cloncurry in the Mt Isa-Cloncurry mineral district of NW Queensland. Ernest Henry Mining Pty Ltd (EHM), a wholly owned subsidiary of Xstrata Copper Australia, operates the mine. Approximately 10.2 Mt of ore grading 1.12 per cent Cu and 0.56 g/t Au were processed during the 2001 - 2002 financial year. The Ernest Henry plant produces copper-gold concentrate, which is trucked to Mt Isa for smelting. The Ernest Henry deposit is a member of the diverse Fe-oxide-(Cu-Au) class of deposits. The orebody is hosted within a sequence of moderately SSE-dipping, intensely altered Paleoproterozoic intermediate metavolcanic and metasedimentary rocks. Copper (chalcopyrite)-gold mineralisation occurs mainly within the magnetite-biotite-calcite ¦ pyrite matrix of a 250 m + 300 m pipe-like breccia body. The breccia pipe comprises two anastomosing lenses separated by a lower grade, clast-supported breccia zone. Several anastomosing brittle faults affect the macro-geometry of the orebody. Copper grade is proportional to the degree of matrix support in the breccia. The July 2002 Ore Reserve was 88.7 Mt @ 1.0 per cent Cu and 0.5 g/t Au. Resource estimation at Ernest Henry is based on a large database of predominantly diamond drill hole information. Drill spacing is typically 50 m + 50 m. Ordinary kriging is used to estimate Cu, Au, SG and IST (oxidation indicator) into model parent cells of dimension 20 m E + 20 m N + 16 m RL. The block model is comprised of five geological-geochemical domains represented by 3D wireframe surfaces. Zonal control, where samples and blocks are assigned the same domain number, is used to control grade estimation. The geometry of the domains defines hard grade boundaries across strike and soft boundaries along strike A Deep Drilling Project was initiated in August 2002 with the initial aim of testing the down-plunge extension of the orebody to a vertical depth of over 1 km. The encouraging intersections to date have resulted in a significant increase in the mineÆs open pit Mineral Resource together with the identification of an underground Mineral Resource. Added benefits of the project included an expanded and updated geological legend and an improved understanding of the host geological sequence.

Jan 1, 2003

By R Williams, P Kohout, J Comins

The Northside Storage Tunnel (NST) is the largest tunnelling project ever undertaken in Sydney. The tunnel extends deep underground from the western bank of the Lane Cove river to the North Head sewage treatment plant (STP), with a branch tunnel from Scotts Creek connecting to the main tunnel under Tunks Park. The aim of the tunnel is to intercept wet weather overflows from four key points along the northernsuburbs ocean outfall sewer (NSOOS) and provide short-term storage and transfer of sewage to NorthHead STP for treatment prior to discharge to the ocean through the deep ocean outfall. The project was an ambitious undertaking by an alliance between the client Sydney WaterCorporationand the engineering firms of Montgomery Watson, Connell Wagner and Transfield to design andconstruct approximately 20 kilometres of tunnel, tunnel declines and shafts in just over three years. In order to achieve this tight timeframe construction of the NST has been undertaken simultaneously at seven construction sites located across the northern suburbs of Sydney. As with most tunnelling operations, tunnel boring machines (TBMÆs) and roadheaders dominated the excavation activities. Tunks Park and North Head STP are the major tunnelling sites. An access decline was excavated using roadheaders at both of these sites to facilitate tunnelling using TBMÆs. Three TBMÆs 3.8 m, 6.0 m and 6.3 m diameter) were launched from Tunks Park and one TBM (6.5 m diameter) was launched from North Head. At the overflow interception sites of Scotts Creek, Lane Cove River and Quakers Hat Bay two vertical shafts known as drop and access/ventilation shafts were constructed. These shafts would provide the linkage between the existing sewer and the tunnel. As their names suggest the drop shaft would convey the wet weather sewage overflows to the tunnel while the access/ventilation shaft would provide access during dry weather and ventilation during a filling event. The fourth overflow site of Tunks Park would use the tunnel decline as its link to the tunnel. Originally these shafts were to be excavated using the raise bore method. This technique however, is entirely dependent on the TBMÆs reaching the shaft locations at the specified time. This was not the case at two of the three shaft excavation locations and top down methods of excavation such as, a percussive cone fracturing (PCF), blind bore, mechanical excavation and drill and blast were investigated to ensure the project met its completion schedule. Traditionally project decisions are dominated by cost and schedule objectives. The contractual arrangement of the Alliance however, required that the objectives of safety, community and environment also be considered in any decision making process. Thus each of these top down methods of excavation were assessed against these five objectives. On considering all of these factors the use of explosives was considered to be the superior technique.

Jan 1, 2001

In 1989 Henry Fairlie wrote a cover story for The New York Republic, 'Fear of Living'. He noted, `The first Apollo space craft caught fire during a test on the launch pad. Three astronauts were killed, the nation was shocked and horrified, all the more because the screams and scrambles of the astronauts could be clearly heard'. After a brief delay in manned flights, the Apollo program resumed with strong public support; within 18 months, Apollo 11 landed on the moon. Fairlie contrasts the Apollo tragedy to the 1986 Challenger disaster. `The prevailing mood in America so panicked NASA that it took almost three years to send up another shuttle', he observed. `In 19 years between these tragedies, the idea that our individual lives and the nation's life can and should be risk-free has grown to be an obsession threatening to create an unbuoyant and uninventive society.' Taking risks is a normal part of our daily routine. The act of living involves minute-by-minute decision-making focused on survival through the practical management of risks. The act of breathing exposes each individual to the risk of infection while the act of crossing the road could almost be considered suicidal. We deal with these constant threats by observing simple rules of hygiene, safety or what may be labelled as common sense. The rules of community, designed to minimise risk in society, can at times lose focus and result in the imposition of schemes that have a far greater cost than the issues from which they protect. Effective management of risk, whether in the community or a business is about awareness and balance and the elimination of unacceptable risk. Risk cannot be eliminated from our lives or our working environment. However it can be managed if it is properly understood, monitored and controlled. The purpose of my presentation today is not to provide a comprehensive technical risk inventory but to capture the essence of risk and the application of management strategies designed to deal with it in a positive fashion. The basis of our differential financial reward system is risk. The key to successful management is to deal with the downside risks in such a fashion that the benefits of enterprise are not eliminated. The key question any investor must consider is `can the major risks assQciated with a venture be managed or eliminated while retaining a greater proportion of upside potential'. The answer to this question is the ultimate value an investor would assign to any project. In reviewing the relevance of risk to our industry the range of papers to be presented today provide examples of how management deals with specific components of risk. In each case the value of the business has been enhanced by the practical application of balanced risk management. The ultimate success of the industry depends very much on this concept as it also provides a public showcase upon which we are judged. Therefore, from all perspectives the effective management of risk is a cornerstone from which to build a stable and progressive mining industry.

Jan 1, 1994

In todayÆs demanding business landscape continual change and technological advancement is a given. With these changes there is now, more than ever, a need to ensure sustainable growth in respect of value protection and value adding whilst meeting the pressures and expectations of the societies in which we operate. Traditionally the management of safety has been a very reactive activity in the business, in some cases seen as an irritation and a disruptive process that demands a focus on preventing reoccurrences. This in turn has focused the measurement of safety performance on a range of lagging indicators û æafter the effect managementÆ. Gaining and maintaining a licence to operate is crucial to a sustainable business but as a prerequisite, organisations need to have a demonstrable ability to manage the safety of their people, as well as mitigating the people risk associated with the business activity. A major focus in the last decade has been on the implementation of enterprise risk management programs, where risk becomes embedded in all business systems and processes and the organisationsÆ genetic make up is programmed to analyse and integrate risk management into all facets of the business activity. The management of safety should be no different. One school of thought argues that there are no new accidents, but rather our inability to learn from the past. Others believe that as long as we have an appetite to achieve the unachievable, we will have to continue to push the boundaries, our safety comfort zones and inevitably take risks. Single reliance on highly evolved technical systems, elaborate processes, highly skilled people, safe equipment and safe work environments have shown one thing û they are not sustainable in providing adequate coverage in the business. In analysing a range of factors associated with some of the worst catastrophes of the 20th century, it can be suggested that they were in fact predictable and inevitable and that an integrated approach underpinned by sound risk management systems could have determined a different result. The key to a sustainable approach in the management of safety requires us to look at a multitude of aspects that collectively allow the performance of an organisation to be predictable. To have certainty in the business activities it is necessary to have controls in place that will mitigate the risks normally associated with unwanted events. It is ensuring that human factors effectively contribute to monitoring the planned approach and being able to safely adjust to any variability. In essence this is having the ability to proactively plan for the longer term. The sentiments articulated by organisational leaders echo that safety management is good business. Surely then a good business is a sustainable business, and a sustainable business is one that provides lasting benefits to its stakeholders.

Jan 1, 2006

Geophysics is playing an increasingly important role in the exploration industry. In the soft rock scene the application of seismic techniques is basically mandatory prior to any drilling program. Simply, this is because, in a majority of situations, the seismic method is ideally suited to mapping accurately relatively flat lying strata and displaying structures that may host oil or gas. It is worth stressing that seismic methods do not delineate oil or gas but they map well in two or three dimensions. In the base metal arena, geophysical methods used are generally focussed on direct detection methods with the mapping application not often used except in potential fields (magnetics and gravity). The success rate in the last decade has not been good but this does not only apply to the application of geophysics; it really applies across the board of exploration techniques. Both geological and geochemical exploration have not had a success rate commensurate with the funds injected. Basically in the last ten years we have failed as explorers! As explorers we have been negligent in mapping. As geoscientists we have let the basic mapping and observation skills diminish û the old adage æboots on the groundÆ is still applicable but are we doing enough of it? The answer is clearly no. As explorers the huge burden of bureaucracy, eg Government Acts û local, state and federal, safety compliance, environmental compliance, etc has reduced the ægeologicalÆ time dramatically. This has culminated in an over-reliance on quick fix solutions, eg spot the bump geophysics or geochemistry. This obviously simplistic scenario is arguable but there is no doubt in the geoscientific areas we have failed in the last decade to provide adequate geoscientific maps to assist in exploration. This failure could partially be responsible for the current demise of the industry resulting in a reduction in exploration dollars and, hence, people. This trend is seen acutely in the geophysical area where the head count in comparison with the geological fraternity is low. Other trends during this downturn are inevitable as explorers maximise the use of the dollar in exploration and diminish spending on advances in geophysics. Improvements are being seen however in geophysical equipment, although it is considered that the main improvement will be in the interpretation of data. Specifically, the trend will be towards integrating geophysical data into geological, geochemical and spatial data sets producing quality interpretation and providing low risk drill targets. Examples of the current trends in hardware and future directions are discussed below. In interpretive schemes there are very few examples of integrated interpretation but the possible trends will be discussed with limited examples.

Jan 1, 2000

By D Judkins N OÆLoughlin

"Basin Minerals Limited commenced exploring for conventional strandline hosted mineral sands (rutile, ilmenite and zircon) deposits in the Murray Basin in April 1997. This has resulted in the discovery of a major mineral sands field in the Douglas Project area, located southwest of Horsham in the Wimmera Region of Western Victoria. After the successful completion of a pre-feasibility study on these deposits in September 2000, the Douglas Project has advanced to bankable final feasibility study. This study should be completed by mid-2002 to allow a decision to commence production in 2003 at an expected rate of in excess of 500 000 tonnes of combined mineral sands products per annum. The field comprises several mineralised strandlines. The main ones of economic interest are from west to east, the four strandlines, Acapulco, Bondi, Bondi East and Echo. These strandlines at August, 2000 contain total Inferred Resources of 443 million tonnes at 4.7 per cent HM at a one per cent HM cut-off; ie 20.8 million tonnes of heavy mineral concentrate which in turn contains 11.3 million tonnes of ilmenite and leucoxene, 1.3 million tonnes of rutile and 1.6 million tonnes of zircon. The heavy mineral concentrate is coarse-grained with mean diameter grain size of the strandline deposits ranging from 130 to 160 microns in size. Major controls on the formation of mineral sands deposits in the Murray Basin are discussed with reference to the main mineral sand bearing, strand plain domains; the Central Strand Plain, the New South Wales Strand Plain and the West Wimmera Strand Plain. The Douglas Project deposits on the West Wimmera Strand Plain domain are characterised by wide zones of mineralisation with high-grade cores (>10 per cent HM), low stripping ratios, and a valuable economic heavy mineral suite comprising 60 to 80 per cent of heavy mineral concentrate. Constituent mineralogy of the heavy mineral concentrate of the overall deposits is; ilmenite (40 to 58 per cent), leucoxene (five to seven per cent), rutile (four to ten per cent) and zircon (four to 14 per cent). The Douglas Project Area appears to be endowed with significantly enhanced levels of heavy minerals compared to other areas of the Murray Basin due to its unique palaeo-geographical position. Long shore drift to the south of the basin has caused large quantities of heavy mineral to be trapped against the palaeo-cliffs and headlands of a rugged palaeo-coastline which includes in a major embayment, the Grampian Mountains, the Black Range and the Glenelg Complex. To the east, major faulting and uplift has brought the fine-grained WIM offshore deposits close to the surface and has resulted in erosional stripping of mineralised strandline deposits. This mineralisation has been recycled and reconcentrated within the younger strandlines to the west within the adjacent Douglas Project Area. These strandlines are thought to be younger than other mineralised strandlines discovered to-date in the Murray Basin. The Project Area strandlines are described; ie their morphology, geology and patterns of mineral distribution. The mineralogy of each of the strandlines is distinctive and variations are noted along strike and section."

Jan 1, 2001