Search Documents

By R Berry

This paper looks at two ways to estimate the bulk mineralogy of the rocks for assay intervals. The aim is to find an efficient indicator of the most common minerals in the rock. Phase (modal) analysis has traditionally been done using visual methods such as point counting and image analysis. A modern version of this process is the X-ray point counting routine using the SEM-EDS based software. These methods are too slow and expensive for routine analysis of bulk sample mineralogy at the normal assay spacing.Two sources of data were considered that provide information that can be used to determine the mineral abundance in assay samples. The most widely applied method is (semi-) quantitative X-ray diffraction (QXRD). The QXRD method is most applicable to major minerals and has limited application to minerals at low abundance. The nominal detection limit is 0.5 per cent. Values below five per cent have large errors. A second, less common, method is calculation of mineralogy from chemical assay data. Conversion of chemical analyses to mineralogical analyses depends on the unique chemical composition of each mineral. Elements only found in one mineral are easily accounted for, but many compositions are ambiguous. Deciding on the actual mineralogy is not simple. Recalculation of mineral mode from chemical analyses is more accurate than QXRD when the correct minerals, and mineral compositions, are known.Where only a few QXRD analyses are available they can be used to setup a protocol for calculation of mineralogy from assay data. Linear programming works well in this environment. The best results are obtained when both H2O and CO2 are directly measured. Loss-on-ignition (LOI) should be included if these are not available.Where both QXRD and chemical analysis are available for all samples, the best results are obtained using the least squared method to merge the data sets assuming QXRD has much higher analytical errors than chemical assays. The combined method provides more robust results because the high abundance minerals are controlled by the QXRD measurements while the chemical assays improve the precision for low abundance minerals

Sep 5, 2011

By K Morrison

Australia’s ageing population means that by 2050 there will be 2.7 people of working age to support each Australian aged 65 years and over compared with five working people per retiree today and compared with 7.5 in 1970 (Swan, 2010). This means that there is going to be a greater demand on social services – for medical and aged care – from a smaller private income base. How will this gap be met? Australia is fortunate in that it has vast resources of mineral wealth; from iron ore, nickel and gas in Western Australia to the giant copper and uranium deposits at Olympic Dam in South Australia.The prospect of a meaningful profit based tax on this vast mineral wealth has been lost through Australian government’s handling of the issue in 2010 and with an industry fiercely opposed to the prospect of a mining tax. Hence, new ways of thinking are required. This paper looks at the issues facing the implementation of a novel scheme whereby Australia leases the mineral resources it extracts and thus derives income over the decades the metals are in-use in pipes, wires and structures with a premium paid for unreturned material or that used in dissipative applications. Applicable minerals could include copper, aluminium, nickel and rare earths. If Australia simply digs up and sells the metals once, the buyer becomes custodian of that resource and they benefit from controlling the future ‘above-ground’ resource stock.A complementary driver for a leasing scheme is the increasing importance of chain-of-custody following initiatives of the Responsible Jewellery Council with gold and diamonds, now with the potential to extend across commodities. The Australian minerals sector could thus position itself as a premium supplier with high social and environmental credentials.Recognising the implementation challenges, this paper includes a review of how such a system could be enforced to ensure that the metal is tracked throughout its life. It concludes with a discussion of the rates and terms should such agreements hold and suggestions for institutional arrangements for enforcing compliance.

Nov 22, 2011

Population growth, social inequality, pollution, global warming, poverty, overexploitation of natural resources and biodiversity loss, are a few examples of the many challenges facing the world today. Sustainable development is about meeting these challenges and improving the standard of living for the benefit of the maximum number of people. These issues concern governments, communities, environmental and social action groups and individuals all over the world. Business too, has a fundamental role to play in delivering sustainable development. In particular, sustainable development is becoming increasingly recognised as a critical issue for the oil and gas industry to address and act upon. BP is committed to positively respond to the challenges posed by the objective of sustainable development.

Jan 1, 2002

By D Kilkenny, D Nardini, P Kline

This paper is a case study highlighting learnings and success in two areas challenging underground miners: change management and collaboration. It examines the implementation process of a new automated loading system in the bulk stoping area of Telfer Mine in Western Australia, controlling multiple load haul dump machines. Here, the new technology has brought together different functions and different companies to deliver a well performing automation system in a changing and challenging mining environment. The introduction of a new and different technology on site has driven collaboration between all stakeholders to break down the traditional barriers to achieve the sustained performance required. Historically, different teams have operated within silos and not always aligned to deliver a ‘best for project’ solution. Technical teams focus on the mine design, maintenance teams focus on reliability and operations execute the plan. Mining contractors focus on productivity and cost. Manufacturers focus on supply of goods and service. Optimising each silo individually is not guaranteed to provide an optimal mining solution. Involving elements from each team as seen at Telfer, has resulted in an optimal mining solution for the automated loading system. A change of focus from the technical teams to include automation parameters in the mine design; operability and maintainability built into the system design allowing for collective ownership and responsibility resulting in a more resilient solution. The implementation of the new technology was not only a technical change but more importantly, successful management of change. Elements of successful change management such as communication, vision, leadership and planning, are essential to harness a trusting site culture which is responsive to new technology. Learnings and challenges from this change process will also be discussed with the intent to improve the success rate and timelines of technology implementations in the future.

Mar 15, 2021

By T Baumgartl, M Edraki, L Huang, D R. Mulligan

"Phytostabilisation with tolerant plant species has been advocated as a cost-effective solution for sustainable cover of tailings from metal mines and bauxite refinery. The development of sustainable plant ecosystems on such wastes requires not only tolerant plant species compatible with local climatic conditions, but also the formation of stable and functional root zones through systematic processes to develop functional soil matrix and horizons (eg A-B-C). However, the process requirements for reconstructing functional root zones in tailings are poorly understood. Based on a review of current literature and industry experience in tailings revegetation, the present paper conceptualises three key phases in the process of root zone development in amended tailings: hydro-geochemical stabilisation resulting from the interactions among tailings characteristics, amendment measures and local climatic conditions the rehabilitation of soil biological capacity the establishment of ecological (carbon and nutrient) linkages between the rehabilitated root zones and the above ground plant communities.Key research is required on: the relationship between hydro-geochemical stability and mineralogy and geochemistry of tailings, in response to rehabilitation treatments under local climatic conditions the relationship between soil biological capacity and hydro-geochemical stability in the root zone the transition of soil microbial communities specific to exogenous organic matters into those required for mineralising litters of in situ plant communities.CITATION:Huang, L, Baumgartl, T, Edraki, M and Mulligan, D R, 2012. Sustainable phytostabilisation of mine tailings - A critical analysis of system requirements and approaches, in Proceedings Life-of-Mine 2012, pp 105-116 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012

By D Genge, E Martin, T Goswami, M Rothery

Rio Tinto’s Hunter Valley Operations is a large open pit coalmine situated in the heart of the Hunter Valley in Australia. The Riverview West Pit has faced increasing production challenges in recent times due to decreasing dragline strike lengths and increasing environmental constraints on vibration, overpressure and fume generation. Conventional mining techniques would involve five to six production blasts per strip to recover multiple coal seams. Each blast event carries the risk of exceeding the strict environmental requirements. By working collaboratively with Orica, it was realised that the blasting method known as Stratablast™, in conjunction with advanced computer modelling techniques, could provide productivity gains whilst simultaneously providing more control over the environmental effects and the impact on nearby infrastructure.As a result of this change, the number of blasts per strip was reduced to one, with the implication that a great deal of care and forethought was needed to manage the increased challenge posed by multiple constraints in the proposed mining area. This innovative approach of combining throw and stand-up blasts allowed the extraction of all major coal seams in a single pass blast event. The blasts were initially designed with a large factor of safety to stay within environmental limits as they were over 1.1 km in strike length, with more than 800 holes and with a total charge weight of about 1000 t of bulk explosives. Furthermore, there were conflicting priorities around the desired blast outcomes. So far, 11 such blasts have been designed and successfully fired. After each blast, innovative design changes have been iteratively implemented to provide further control over environmental impacts, whilst continuing to improve productivity. As a result of these changes, blasts have progressively increased in complexity with the inclusion of features such as damage zones, mid-splitting, time gaps and different directions of firing. The consequence of this complexity is that the blast duration can be as long as 28 seconds to accommodate all components of the blast.This project has increased the productivity of the Riverview West Pit through blast design improvements and allowed the environmental impacts to be managed with far more control and predictability than would have been possible under a conventional blasting regime. There still remains room for further optimisation of mine productivity and this is being addressed through a process of continuous improvement.CITATION:Goswami, T, Martin, E, Rothery, M and Genge, D, 2015. A holistic approach to managing blast outcomes, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 645–654 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By P J. Hawke

Within the Mesa J pisolitic iron ore mine, clay is distributed unevenly throughout the deposit and often forms as pods and channels less than 10 m in width. The mine resource model, based on 50 m + 50 m spaced drilling, has been unable to accurately delineate the clay for scheduling and mining purposes. Therefore, alternative methods for mapping the clay-contaminated ore were sought. Predictive clay mapping will significantly reduce production costs at Mesa J through improved selective mining practices, more accurate scheduling, reduced wear on mining equipment and minimising the need for maintenance of haul roads and ramps. High lateral resolution electromagnetic (EM) surveying using a Geonics EM31 instrument can quickly and inexpensively delineate the extent and orientation of the clays. Preliminary results indicate that a block model based on the interpretation of the EM data can accurately predict the distribution, volume and tonnage of ore and waste material. While rip-line mapping, infill drilling, ground penetrating radar and gravity can delineate clay with various degrees of success, none were as efficient as EM31.

Jan 1, 2002

By N Redwood, N Fowkes, A Bassom, S Durkin

"It is well known that from time-to-time a vehicle will interact with a bund or windrow and often the barrier is insufficient to safely arrest that vehicle. The result of such an incident is often catastrophic. Regulations around the requirement for edge protection near pit edges vary between jurisdictions. Generally in Australia regulations tend to be around placing the responsibility on the mine operator to provide ‘adequate’ or ‘appropriate’ edge protection. Guidelines often place a minimum height of bund at between half and two-thirds the diameter of the largest tyre on-site.Safescape has identified the opportunity to improve safety in open pit edge protection and is currently developing the Edge Protector (EP) product. The EP is designed to create a vertical front face to a conventional broken rock safety bund. The fundamental premise of the product is that by creating a vertical front face to the bund, trucks cannot easily drive up over the bund and instead have to push through the rock to get to the other side.In addition to providing a safer system for arresting vehicles, the vertical front face also means that extra space is made available in the haul road. This can either be used to facilitate larger trucks or when designing a new mine, with an increase in overall pit slope.This paper outlines the research and development of a new edge protection product. Discussion will include project objectives, economic incentive for mines to apply the system, mathematical analysis of the truck/bund interaction and physical testing of the product.Citation:Durkin, S, Fowkes, N, Redwood, N and Bassom, A, 2016. Innovative Approach to Open Pit Edge Protection, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 138–149 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By P Crittenden

Thiess Pty LtdÆs Australian Mining business unit used 7.6 PJ of energy in the 2007/2008 financial year. This represented more than 85 per cent of Thiess Pty LtdÆs total energy use and therefore meant that the Australian Mining business unit is required to conduct energy efficiency assessments and report publicly on the outcomes by December 2008 under the Federal GovernmentÆs Energy Efficiency Opportunities (EEO) Act. Thiess Pty Ltd has a policy commitment to sustainable development throughout its operations. This includes minimisation of its carbon footprint and the Australian Mining business unit has a strong focus on efficiency in all of its operations. It approached the energy efficiency assessment as an opportunity to further improve and build on its energy efficiency and greenhouse gas reduction focus in the business. As a mine contractor, Thiess faced a number of challenges in designing an assessment process that would be both effective and efficient to deliver. For example, unlike most other companies involved in the Energy Efficiency Opportunities program, the energy use associated with the Australian Mining business unit is not fixed to any single geographic location in Australia. Mining vehicles are moved from site to site according to the specific requirements of mine owners and the timing associated with the commencement and completion of contracts. Thiess departed from a traditional æsite by siteÆ based assessment and designed a ærepresentative assessmentÆ approach that involved detailed investigation of data across all sites and a focused assessment on a single site.Data and analysis was an essential part of the assessment and indicators at company, mine and site level were essential in identifying opportunities and tracking progress. Forty-six potential energy saving opportunities were identified and four of these are currently being implemented. The projects being implemented are: payload management, automating mobile lighting equipment, plant idle time management, and turbo idle downtime. The potential savings from the four major projects that have been identified are approximately 150 800 GJ/annum, equivalent to 10 600 tonnes of CO2-e/annum with a simple payback period of less than two years. Beyond the fuel savings however, there are a number of other benefits from the assessment, including operational efficiency, reduced maintenance costs and even a potential reduction in the number of vehicles required to complete the work. The EEO assessment has significantly increased the importance and urgency of energy efficiency and facilitated the sharing of good practice across all Thiess operations. Not only have four projects been adopted for immediate implementation but a further pipeline of projects is available for future possible implementation. This case study describes: how Thiess conducted its assessment including the use of energy data and indicators, the opportunities identified that are currently being implemented, and the lessons learnt and how other organisations can use these to improve their approach to energy efficiency assessments. This case study is a more comprehensive version of a case study developed for the Commonwealth Department of Resources, Energy and Tourism. The assessment results reported in this case study are drawn from the Thiess Energy Efficiency Opportunities Report 2008.

Jan 1, 2009

A comparison is made between elementary block estimation techniques and the optimal methods of geostatistics using data from an Australian deposit. Considerable improvement in the estimates are obtained by using the optimal technique in this case.

Jan 1, 1975

By D W. Nisbet

Today Hudson Bay Mining and SmeltingÆs 777 Project is the largest mining construction project under way in Canada. The project comprises six components: construction of the new 777 zinc-copper mine; construction of the new Chisel North zinc mine that will truck ore out from 600 metres below surface; expansion of the Flin Flon ore concentrator; expansion of the zinc plant to increase throughput by 15 per cent; a spill gas project that will reduce fugitive gas emissions by some 90 per cent; and infrastructure improvements including construction of a new electrical substation. Total investment in The 777 Project is over $US 260 million. Seven years ago, the Flin Flon, Manitoba-based company was fighting for its very existence. How does a company go from down-for-the-count to robust contender in just seven years? Contributing reasons are many, but all have their root in a process HBMS calls æTransformationÆ. It is transformation that has taken HBMS, a very traditional company, through a very non-traditional turnaround (Figure 1).

Jan 1, 2000

By Kubik K

This paper reviews the historical data on relative height changes of landmasses with respect to sea level for Pacific Rim countries.It discusses existing theories of the Greenhouse effect, and the interaction with the vertical movements of the continental plates which leads to different effects for different places. Possible future scenarios are described and directions for future research and measurement programs are given.Relative sea levels are governed not only the increase of water from deglaciation but also by a range of other factors such as variable water storage in lakes and the atmosphere, thermal expansion of the ocean, ocean currents, and the shape of the ocean and the continents. Sea floor spreading, for example, is ultimately more significant than deglaciation in sea level control but is generally much slower.

Jan 1, 1990

By O Dominguez

Significant value can be added to ore supplied from the mine to the mill by measuring its quality in real time and performing grade control additional to that within the mine. Responsibility for ore quality between the mine and mill stockpiles is not always clear due to operational siloes so geologists and mining engineers need to be involved collaboratively with metallurgists to optimise ore value prior to processing. Sensors, such as the GEOSCAN-M which utilises high specification Prompt Gamma Neutron Activation Analysis (PGNAA), that measure conveyed ore flow representatively (continuous and fully penetrative) and in real time have been used in the minerals sector since 2003 and have been successfully applied in multiple commodities. Quality can be measured within the mine where material is conveyed underground or in-pit. Bulk ore sorting is used to divert increments of waste from the ore stream to upgrade material sent to the crushed ore stockpile (COS) as well as to create run-of-mine (ROM) stockpiles of different qualities to maximise blending opportunities and accommodate processing priorities, eg blending out deleterious content. The real time composition measurement can be combined with moisture and fragmentation analysis data for improved ore type characterisation, to control ore blending, for feedback to the mining schedule and block model reconciliation, and feed forward control for grinding and processing operations. The paper discusses various parameters measured and derived in existing operations that are used to maximise coarse waste rejection and metal recovery, optimise plant feed quality consistency, and reduce consumables; power, grinding media, water, reagents, and minimise fine tailings generation. Innovative geometallurgy applications are also discussed.

Mar 22, 2022

By Kleine T. H

Blast design involves many engineering constraints and objectives. Some of the more important include the implementation costs, the desired fragmentation and shape of the muckpile. A spreadsheet has been developed to allow blast design options such as burden, spacing, blast hole diameter, decking and explosive type to be varied. As any option is varied the spreadsheet recalculates and graphs the expected implementation costs, fragmentation and muckpile shape in seconds.The spreadsheet extends the philosophy of simple robust fragmentation prediction (Cunningham, 1983) to include similar models for explosive detonation (with respect to explosive type, age, blast hole diameter and density) and muckpile shape (with respect to burden, spacing, charge location and weight). The new empirical models for explosive detonation and muckpile shape prediction have been calibrated successfully for one situation and are now undergoing further field trials.

Jan 1, 1992

By P Thompson, D Rose, S Yu, W Baum, R Zahn, D Meadows, G Hall

Opportunities to improve mill operations are often cited by mining companies and recognised in many concentrators spread throughout the world but are not always followed through. Copper-molybdenum concentrator operations are challenged by a continuously increasing list of detrimental factors. They include deteriorating ore characteristics and poor mineralogical information on deeper ores, water quality and availability, steel wear and increasing power costs. Rapidly declining productivity, sustainability and environmental factors, new taxes, mining industry global skill set shortages, to name but a few, must also be considered. The days of maximising value by just increasing production or simple cost cutting are fading and will not be sufficient for the future of more complex mineral processing operations and larger plants. As a result, FLSmidth’s Global Process Technology Group has launched a plant and process optimisation program based on mineralogical and metallurgical surveys.Copper-molybdenum concentrators of the future need a paradigm shift. Modelling and simulation tools alone are not the answer to complex mineralogical associations and larger scale equipment and operations. Detailed area by area review aimed at identifying process constraints in terms of equipment and operating practice in conjunction with robust diagnostic work, ie mineralogical and metallurgical characterisation, are mandatory for process optimisation. The navigational beacon, for all operations who want to remain competitive, will be ‘process efficiency’. Since the use of automated mineral analysers has become more readily available and reliable, mineralogical-metallurgical plant surveys have proven themselves as the most efficient tool for optimising plant performance.The following paper will illustrate how operations can move toward eliminating under-performing flow sheets, fixing run-away flotation conditions, maximising individual process equipment performance, preventing shortcuts in Bond work index testing which may cause the failure of comminution models and minimising costly and time-consuming ‘debottlenecking’. As previous plant surveys have shown, the net project cash flow can be increased by 50 to 200 per cent if a combination of robust ore characterisation and plant process mineralogy is performed. The combined plant survey approach has been demonstrated successfully in a multitude of operations. This includes the use of key ore types in concert with statistically sampled process streams, bench-scale metallurgical tests and automated mineral analysis on a size-by-size basis.CITATION:Meadows, D, Hall, G, Rose, D, Thompson, P, Baum, W, Zahn, R and Yu, S, 2014. Copper-molybdenum concentrator surveys using mineralogy and process benchmarking tools to improve overall plant performance, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 315–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By R F. Cota, C Freeman, A Heberle

"The Lamego mine is an underground gold mine in the Iron Ore Quadrangle in Minas Gerais state, Brazil. The mine produces 48 to 50 koz per annum, as part of the larger Cuiabá-Lamego Complex. This combined unit is AngloGold Ashanti’s largest gold producer in the Americas, contributing with 310 to 320 koz per annum.The mine started production in 2009, utilising cut-and-fill mining methods.A mining method change was trialled in 2014, introducing open stope methods. The key benefits proposed from this change are considered to be: improved safety by eliminating re-entry mining methods reduced mining costs/increased productivity from utilising bulk-mining operations.The results from the trial were encouraging, and open stoping participation expanded beyond a trial.Production from open stope areas reached 180 000 t (40 per cent of total run-of-mine; ROM) in 2015. While the change in mining method resulted in higher production rates, it also introduced a critical issue in terms of stope recovery rate.Average underbreak (unplanned loss of ore) in the larger open stopes reached 21 per cent in 2015. To manage this ore loss, a project targeting higher recovery was structured with three primary components: analyse current performance to define contributing factors (design process gaps, operating practices) investigate corrective actions apply corrective actions and maximise team engagement to ensure changes become standard practice.Within six months of commencement, a range of contributing factors had been identified, and the majority of the associated corrective actions implemented, including increased team engagement to ensure changes were not ‘once off’ actions.The outcomes show a clear reduction in underbreak (average ~12 per cent for 2016), with further improvement opportunities identified. The challenging target is now to achieve a further reduction to 10 per cent underbreak as the average for 2017. The results contributed 1400 oz and additional US$ 0.5 million to the cash generation profile for 2016.CITATION:Heberle, A, Freeman, C and Cota, R F, 2017. Increasing stope recovery in an underground gold mine by using effective analysis, corrective action and employee engagement processes, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 117–122 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 16, 2017

By J Robinson, L D’Uva

"The Gold Fields group and Gekko Systems have successfully worked together on multiple projects, including at the St Ives, Agnew and Granny Smith operations in Western Australia, and the Damang operations in Ghana, with gravity recovery design, technology installation and optimisation the key driver on each occasion.In 2014, Gold Fields Australia identified an opportunity to challenge the historical thinking at Granny Smith and reassessed the benefit of upfront gravity gold recovery. The historical approach had been to employ gravity on the tailings stream of the carbon-in-pulp (CIP) circuit, recovering sulfide minerals into a concentrate from spiral concentrators for further liberation of gold via a regrind circuit.Gekko was engaged to assess the implementation of a gravity circuit within the grinding area, and to perform a comprehensive gravity recoverable gold test program. Test data was fed into the AMIRA P420 BCC Gravity Model to confirm the gravity recovery potential of the ore, and for process design basis generation. Height, space and capital limitations proved to be a design challenge. However, collaborative learnings throughout the project ensured the design and operation of a reliable and economic gravity gold circuit. Ultimately, the Granny Smith gravity circuit was a success, satisfying all the project objectives and yielding consistent, measurable benefits. On average, the gravity circuit recovers 33 per cent of total gold, resulting in an increase to overall gold recovery by 0.7 per cent.This paper highlights the key project drivers for Gold Fields, and the development of the Granny Smith free gold gravity circuit. It details application of test work and modelling, and the challenges and learnings encountered during the design, installation and commissioning stages. This paper seeks to demonstrate that continuous improvement in a long standing operation can be beneficial to overall circuit flexibility and increased ounce production.Citation:D'Uva, L, Robinson, J and Bell, T, 2016. Defying Gravity - Brownfield Continuous Improvement, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 135–144 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By P A. Grossman, J H. Rubinstein, M Brazil, K G. Sirinanda

To date, the scheduling and access design of an underground mine have only been considered as two separate optimisation problems. First, access to the mine is designed and then the scheduling is completed. One drawback of this approach is that the costs of access construction fail to be reflected in the net present value (NPV) calculation. In this paper, designing the access and scheduling its construction are formulated as a single optimisation problem.The underground mine access construction process can be classified according to the number of faces being developed concurrently. An underground mine with a single decline branching at a junction point into two declines is considered. After construction reaches the junction, the two faces of the decline can be constructed sequentially or concurrently.This paper proposes an efficient algorithm for optimally locating a junction point to maximise the NPV where two faces are being developed concurrently. The NPV is defined by taking the locations of orebodies and their values, decline construction costs, decline development rate and discount rate into account. The variation of the NPV and the optimal locations of the junction point for one and two concurrent development faces for a range of discount rates are discussed and compared. The proposed algorithm is applied in a simulated case study based on hypothetical values for an underground mine.CITATION:Sirinanda, K G, Brazil, M, Grossman, P A, Rubinstein, J H and Thomas, D A, 2014. Strategic underground mine access design to maximise the net present value, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 235–242 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By S Wilkinson, S Black, L van den Berg

"The mine ventilation system plays an important role in mitigating human exposure to diesel particulate emissions (DPM), exhaust gases and heat in underground mines. The mine’s secondary ventilation systems are critical for diluting contaminants when working at the face of a heading. To improve these systems it is important to understand and visualise the localised air flow profiles. We have considered an approach that includes both tracer gas measurement–modelling to analyse this complex flow behaviour in a heading. The use of tracer gas enables reliable measurements of flow behaviour and differentiation between the contributions of various contaminant sources including DPM. A pilot study was conducted to demonstrate how tracer gas can be used to directly measure the effectiveness of ventilation dilution in a heading during shotcrete activity. This activity is considered to be one of the more challenging areas for diesel exhaust exposure management. Exposure sources include the diesel engine of the spraying equipment (Spraymech) and concrete agitator truck (Agi) that supplies the shotcrete. During operation both the Spraymech and Agi operators are located outside the equipment’s air-conditioned cabins and both are exposed to diesel exhaust. In the pilot study tracer gas was injected directly into the Spraymech exhaust stream. This allowed thorough mixing, ensuring the tracer gas was able to track exhaust gases and particulates released to the heading. The release was repeated at three different headings with varying degrees of secondary ventilation controls. The study showed that small changes to the secondary ventilation system can significantly impact the contaminant concentration. It also demonstrated that tracer gas can be used to isolate different contaminant sources. The intent is to use this technique in a more comprehensive study to develop best practice guidelines for secondary ventilation installations. This paper presents the technique used and the preliminary results from the pilot study. CITATION: Wilkinson, S, van den Berg, L and Black, S, 2015. Application of tracer gas flow profiling to improve secondary ventilation practice – a pilot study, in Proceedings The Australian Mine Ventilation Conference, pp 345–352 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 31, 2015

By Bodnaras G. E, Sceresini P. A

The Filblast Cyanidation Process incorporates the advantages of intense high shear mixing, high dissolved oxygen concentration and high pressure to achieve extremely rapid gold dissolution rates. This is made possible by the unique design of the Filblast gas shear reactor. The reactor is a rugged and compact in-line device. The outer casing is protected by a polyurethane coating and the internal parts are of wear resistant polymer. The largest unit built to-date has overall dimensions of 1200 mm length by 300 mm diameter and has a capacity of 150 dry tonnes per hour at 40 - 45 per cent solids. Service life at this throughput is at least three months. The process may further be applied to high temperature leaching of refractory gold ores or other metals. Wear resistant metal or ceramic materials would be employed for this duty. Four mines are currently employing the Filblast Process for treating a variety of ore types ranging from highly reactive, almost impossible to treat, pyrrhotite/arsenopyrite to deeply weathered clay ore which forms a highly viscous pulp. The effect of shear thinning has resulted in improved adsorption kinetics resulting in higher carbon loading and reduced soluble gold loss. Total tonnage treated is approximately four million. Operating costs which include leasing and maintenance charges for the Filblast and pump power costs are about 16 cents per tonne. This is equivalent to about ten per cent of savings. Laboratory scale units having capacities up to 30 litres/min are available for test work but laboratory testing techniques so far developed do not accurately reflect the oxygen and cyanide savings which have been achieved in the plant.

Jan 1, 1994