Search Documents

By E J. B van Etten

This paper reports on the results of several years of monitoring rehabilitation at a silica sand mine on the Swan Coastal Plain, south of Perth. Mining here occurs below the regional watertable and leaves a post-mine landscape of dredge pond voids (pit lakes) with surrounding battered slopes. The restoration we recommended was to develop the pit lakes as wetlands of regional analogue and value. Several different restoration techniques have been applied to re-vegetate pit lake slopes over many years which have enabled an evaluation of reasons for success/failure of different restoration approaches. Learning acquired clearly showed the benefits of using fresh topsoil for restoration over topsoil that has been stockpiled for several years. Most topsoil used in restoration was from seasonal wetlands and consequently restoration was most successful in the riparian zone from the edge of pit lakes to about 2 m vertically above the water table. Topsoil restored areas above this level remained poor in plant species and cover. Conversely, remedial seeding/planting proved largely unsuccessful. Permanently and seasonally flooded pit lake margins recolonised relatively quickly and successfully with native sedges and rushes. Development of rehabilitated upper slope plant communities over time was evident with loss of typical wetland species and greater growth and survivorship of upland and dampland plant species on mid to upper rehabilitated slopes. Plant communities of lower slopes showed a converse pattern of development, with a shift towards a more typical wetland composition. We believe matching topsoil to site and development of topographic profiles similar to natural wetlands of the region are the keys to optimising restoration success of sand mines with shallow water tables.

Oct 5, 2011

By Kanau JL, Kilgour I

This paper describes the metallurgical processes at the 80 000tpd Ok Tedi Mining Limited concentrator, which treats copper- gold ore by single-stage crushing, SAG and ball milling and flotation to produce over 500 000tpa of concentrate. Plant and process developments, including installation of column cells, reduction of fluorine in concentrate, use of sulphidisation and process control improve- ments are also discussed.

Jan 1, 1991

By R Crosbie, K C. Runge, E Tabosa, J K. McMaster

Flotation feed density is an operating parameter which is currently not well understood. Most models of flotation only incorporate its effect on particle residence time, but it is likely to have additional effects within both the pulp and froth phases of the machine. Test work was performed in MetsoÆs 3 m3 RCS test rig to investigate the effect of flotation feed density on metallurgical performance. The rig was operated at Rio TintoÆs Northparkes operation using flotation feed and scavenger tail. For each feed, tests were performed at different feed densities, and measurements were performed to estimate the pulp and froth recovery as well as other key flotation parameters (eg bubble size, turbulence and froth stability). Results of this test work have shown that the pulp density does affect key parameters of the flotation process in both the pulp and froth phases. Pulp phase kinetic rates decrease at high density and this is attributed to a reduction in the turbulence within the cell. Froth phase recovery, however, improves presumably because of a stabilising effect due to a greater loading of solids on bubble surfaces.There is a need for more research to be done to better understand these interactions so that metallurgists can determine the optimum flotation feed density to use at a particular operation, or within a section of a flotation circuit.CITATION:Runge, K C, Tabosa, E, Crosbie, R and McMaster, J K, 2012. Effect of flotation feed density on the operation of a flotation cell, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 171-178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By M T. Nguyen, S Vink, M Ziemski

On any given mine site the water system is contingent upon its initial design. Through time the initial design is adjusted by a myriad of water management options in order to improve water system performance or to adapt to a new production capacity or method at the mine site. These options generally do not comprehensively consider energy requirements, so it is unlikely that any given mine water system will be optimised in terms of both water and energy uses. Thus this may simply shift constraints of efficiency of one resource dimension, water, to another, energy. As a result, changes in water systems would cause more energy-related issues to mining companies. For example, the companies would have an increase in operational cost and/or pay more for carbon tax with changes in their water system. Therefore, in order to avoid undesirable and potential unforseen energy and infrastructure issues in a mine life cycle, it is essential to select suitable water management options for a mine considering both water and energy resources simultaneously.Considering water and energy criteria in evaluating water management options consists of net water volume availability, net operational energy demand and net water replacement energy demand. Ideal water management options should be high in water volume availability but low in both operational energy demand and water replacement energy demand. A water option would also be favourable if it has low potential of causing adverse environmental impacts such as lowering groundwater tables due to groundwater withdrawal, or elevating saline constituents in surface waters when reusing brine for dust suppression. However, these environmental impacts are not considered in this analysis.This article presents a graphical method to assess mine water management options, based on these three criteria. The proposed method to assist in screening mine water management options includes two main steps:1. categorise water management options into prioritised groups2. rank the options within each prioritised group.The method is applied to a gold mine and presented in this article as a worked example. CITATION:Nguyen, M T, Vink, S and Ziemski, M, 2013. Selection of mine water management options considering both water and energy impacts, in Proceedings Water in Mining 2013 , pp 29-34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By A Whaanga, W Vigor-Brown

IGO Ltd’s (IGO’s) Nova-Bollinger Deposit (Nova-Bollinger) is a magmatic nickel-copper-cobalt (NiCu-Co) sulfide deposit found 160 km east-north-east of the town of Norseman in Western Australia (WA). The deposit is hosted by the Mesoproterozoic rocks of the Fraser Zone, which is part of the Albany Fraser Orogen (AFO). Since mining commenced in 2016, IGO’s Nova Operation (Nova) has mined and processed to 31 December 2020, 5.63 Mt of ore grading 2.04 per cent Ni, 0.86 per cent Cu and 0.07 per cent Co. Nova’s mine geology team (MGT) has used commercially available implicit modelling (IM) and general-purpose resource modelling (RM) industry software systems, to prepare the 31 December 2020 (CY20) update of Nova-Bollinger’s JORC Code reportable Mineral Resource estimate (MRE). This CY20 MRE update was predominantly based on ~386 km of diamond core drilling, with the drill holes having a nominal grid spacing of 12.5 by 12.5 m throughout the mineralised zones of the deposit. Using IM tools, Nova’s MGT interpreted and modelled 22 separate domains from the drill hole logging, assaying results, and the MGT’s underground mapping. These IM closed volumes were then used to control the estimation of MRE variables into conventional industry digital block models using RM and other ancillary software systems. During 2021, a commercial machine learning (ML) software was trialled by Nova’s MGT for preparing block models of Nova-Bollinger’s MRE domains. The motivation for the trial was that the ML process could expedite modelling through the direct creation of a domain coded block model from the drill hole logging. Compared to the industry standard approaches of wireframing or IM, where the modeller usually makes many subjective choices to produce the domain model, ML offers a more objective ‘hands-off’ process for determining the connectivity of domains defined in drill holes. Additionally, the ML process provides a quantitative confidence metric associated with its output that may have utility in mine production and resource classification. In this paper, the results of the Nova-Bollinger ML modelling trial are compared to the MGT’s current workflow for MRE work. The MGT’s conclusions as to the advantages and disadvantages of the IM and ML methods for preparation of MRE domains are discussed. The ML software was also tested as a method of rapidly interpreting geology outside the principal zones of MRE interest. These testing results are also presented in this paper.

Mar 22, 2022

By S Thomas, S Ricketts, R Hassell

Northern Star Resources (NSR) operates several operations utilising narrow vein stoping operations in the Kundana area. Stope dilution performance is variable across these operations, with unplanned dilution reducing individual stope economic viability, increasing risk to personnel and machinery operating in and around the stope and delaying the overall stoping sequence. Technical investigations were undertaken to objectively understand the variables which had the largest impact on stope performance and then use the findings to help develop mining strategies to reduce dilution. A stope reconciliation process was developed to compile key stope performance information such as stope design parameters, geotechnical and drill and blast factors. These were compared against the measured dilution. Production targets necessitated a high turnover of stopes in the operations, and hence a requirement for an expeditious process and mine design software with automated tools. The output of these results, together with numerical variables from geological, geotechnical and drill and blast data were analysed via multivariate regression. The analysis identified the factors with the greatest influence over stope dilution, and a forecast model was consequently created. Confidence was gained in the model when the subsequent stopes performed in line with prediction. Different drill and blast designs were subsequently trialled and found to reduce dilution. The model was then updated with the new practices, facilitating further regression analysis to identify revised key controlling factors. The subsequent production results however, displayed a poor correlation with the prediction from the revised model. Inconsistencies in drill and blast designs and execution were identified as key factors in the dilution performance. This was an important finding as the correct implementation of the design is critical and this has become a key focus for future stoping. Overall the technique presents an objective process to identify causal factors of stope dilution resulting in improved economic metrics for stope production. The process will be applied to other similar Northern Star operations.

Mar 15, 2021

By I R. F MacCulloch, K Jones

Pintail Systems, Inc, a Colorado USA based company has developed and commercially applied bioremediation processes for biological detoxification of cyanide compounds in mine waste. Site-specific microorganisms are isolated from spent ore, tailings or process solutions and augmented in the laboratory for cyanide oxidation, denitrification and metal biomineralisation. Biological processes typically treat complex contaminants (cyanide compounds, soluble metals and nitrates) in a fraction of the time of conventional remediation processes. Cyanide is used in microbial metabolic processes as a carbon or a nitrogen source. Biological detoxification processes applied at the end of mine life can end long-term liability and perpetual monitoring and containment. Case studies from commercial application and demonstration programs for the US Environmental Protection Agency will be presented in this paper.

Jan 1, 2004

By C Fischer

The introduction of digital communications technologies into the underground mining industry, in both coal and hard rock mining, has enabled high bandwidth applications to be applied in the mining industry. Digital networks based on 802.11 b/g/n open Wi-Fi standards have allowed numerous applications to be run over a single communication backbone. One of the many important applications is the tracking of personnel and equipment via RFID Tags. This tracking application has formed the basis of a Proximity Detection System or Collision Avoidance System (Schiffbauer and Mowrey, 2001; Kent, Fischer and Schiffbauer, 2011) thereby improving safety and increasing control in the mining environment. This paper discusses the growth of digital technology as the backbone for communications in underground mining applications. This growth has allowed the ‘convergence of technologies’ (occurring in the general business world) to be available to mine operators in general and underground mine operators in particular. Mine Site Technologies’ involvement with major mining companies and mining equipment manufacturers (OEMs) in developing and supplying their communication systems is also discussed.The latest technical requirements and specifications for communication systems for underground and open cut mines will be reviewed.

Nov 22, 2011

Is your company paying taxation on profits which are partly illusory?ò Are unions making wage demands based on erroneous notions of the real level of value added to your companyÆs production?ò Do you receive historic data on profit contributions by different products, or for different market areas, which you feel may be misstated?ò Do you find that cash is not always readily available to pay dividends out of reported earnings because, it is required to finance additional working capital without a real increase in the level of activity?ò Are your planning and budgeting routines hampered by the need to rely on historic financial data which bear little resemblance to what the future may hold for your company?ò Are you able to maintain your business at its optimum operating capability or do you feel each year that it becomes more and more difficult to achieve the same volumes of prdduction at the same level of return on assets employed without having to raise more capital?If your answer to any of these questions is "yes", then it is very likely that Current Cost Accounting (CCA) has something to offer you!characteristics of the mining industry and for single venture mining operations.

Jan 1, 1984

By N F. Glenn, S Thiruchittampalam, B P. Banerjee, S Raval

The determination of shear strength parameters for the spoil material plays a crucial role in the assessment of a dump’s stability; nevertheless, their evaluation necessitates laborious laboratory experiments. In order to address this issue, Simmons and McManus (2004) formulated a framework that serves as a foundation for categorising spoils according to their distinctive shear strength parameters based on observable and tactile characteristics. This framework, previously identified as the ‘BHP Mitsubishi Alliance Coal (BMAC) Spoil Shear Strength Framework’, is now recognised as the ‘CoalSpoil’ framework. The spoil characterisation provided by the CoalSpoil framework offers benefits but is not without limitations. The examination of these attributes in the field is a time-consuming task that demands expertise. Subjectivity arises in the spoil characterisation when attributes straddle the line between two categories, such as delineating matrix-supported and framework-supported fabric structures. To enhance consistency in the spoil characterisation process, minimising human intervention is crucial to mitigate bias, classification errors, and safety risks. This study seeks to achieve this aim by introducing image-assisted and automated methods for spoil characterisation.

Sep 1, 2024

By D Phillpotts, S M. Mantsho, P Strobos

A challenge on many industrial flotation circuits is controlling concentrate mineral grades using measurements that are provided infrequently. The mineral grades in concentrate streams are a critical performance indicator in any industrial flotation circuit. Failure to achieve concentrate mineral grade targets has significant financial consequences on a flotation operation. A violation of a gangue mineral grade limits by the concentrator may also result in significant penalties. Online grade analysers which can provide reliable real-time grade measurements are essential for effective grade optimisation. The Blue Cube MQi analyser (by Blue Cube Systems) has recently come to prominence for its ability to rapidly determine mineral concentrate grades online and in-stream. This has provided excellent insight into the actual process dynamics in the flotation circuit, and hence enabled real-time control and optimisation of concentrate mineral grades. MintekÆs Measurement and Control division, specialising in advanced control solutions for mineral and metallurgical industries, has had the opportunity to link the FloatStar Grade-Recovery Optimiser to the measurements provided by the Blue Cube system at a nickel concentrator plant. The project initially focused on stabilising the final concentrate grade without directly accounting for nickel recovery. The site later procured additional Blue Cube MQi analysers, resulting in the expansion of the FloatStar Grade-Recovery Optimiser to incorporate recovery component in the performance. This site already had the FloatStar Grade-Recovery Optimiser for several years, but the original grade measurement device was unreliable and ultimately failed. The system was reactivated once the Blue Cube system was installed, replacing the old analyser.CITATION:Mantsho, S M, Phillpotts, D and Strobos, P, 2012. The implementation of FloatStar grade-recovery optimisation control solutions using Blue Cube online grade analysers on industrial flotation circuits, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 363-368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By S H. Algie, D P. Taplin, S G. Doig

"Suboptimal performance of clusters of hydrocyclones (cyclones), relative to the performance of the individual cyclones that comprise the cluster, is a common phenomenon. The primary cause is well known: uneven distribution of the slurry feed into the individual cyclones. The direct result of uneven distribution is that each cyclone in a cluster performs somewhat differently. Hence, some, if not all, of them do not work at their intended operating points, and the classification is not as sharp as intended. The impact on grade, recovery and milling efficiency will vary depending on the duty of the processing circuit, but the most immediately apparent consequence of uneven distribution is a difference in wear rates in the individual cyclones; this exacerbates the problems of unequal performance of the individual cyclones. In severe cases, and as differential wear proceeds, flows from the individual cyclones may become visibly different. Uneven distribution, once the phenomenon was identified, was seen to be a significant issue in the high-solids hydrocyclone cluster in the ball mill recycle section of Evolution Mining’s Edna May Operation (EMO, Westonia, Western Australia) gold processing plant. In 2012, a FloCEP® hydrocyclone feed distributor system was installed to alleviate the problem. Over the next four years of operation, this innovation has proven its value in the metallurgical and maintenance areas. Individual cyclones now wear at the same rate, greatly reducing the need for operator intervention, as well as increasing overall plant availability through minimising unplanned maintenance. The costs of the installation can be justified by savings in maintenance alone, though the greatest value, as is described in this paper, is in allowing the plant to produce consistently closer to its operational design limits. The FloCEP® system is a low maintenance, readily installed retrofit, based on two patented devices that are combined with complementary proprietary design methodology allowing customisation for specific flow rates and slurry particle properties. Together, these devices produce and distribute a pseudo-homogenous slurry flow without moving parts.Citation:Taplin, D P, Doig, S G and Algie, S H, 2016. Experience with FloCEP® Slurry Flow Conditioning at Evolution Mining's Edna May Operation, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 251–260 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

Opening AddressThank you for inviting me here today to open what promises to be a significant conference on the technological aspects of extractive metallurgy. I would especially like. to welcome delegates who have travelled great distances in order to contribute to, and be participants in, this examination of the technical innovations which have always been a crucial part of our industry.

Jan 1, 1992

By L Boczek

The term Engineer of Record (EoR) is commonly used in North America and South Africa to define the responsible person for the design, construction and operational phases of a tailings storage facility (TSF). Recently, this role has been elevated in prominence within Australia, but what does it really mean? Recent updates to international TSF guidelines suggests appointing an EoR is good practice, but where does the responsibilities of the EoR start and finish. Interestingly, both Samarco and Mount Polley failures had active EoR’s in place. This suggests that nominating an EoR alone, is not the full answer to mitigating the potential for a TSF failure. Appropriate construction and operational practices are key to the success of the design of TSFs, where all too often, operators ignore the operating plans developed by the designer. To be successful, a key consideration of the EoR role, is involvement in the operational phase of the TSF. This requires ‘buy-in’ from the mine managers and a change in the way TSFs are perceived by site. This paper explores how the roles and responsibilities of the EoR can assist in improving governance of TSFs if implemented effectively and what role the client has to ensure the success of the EoR.

Jul 1, 2021

By C D. Pocock

Maintaining catch berm capacity in open pit mines through controlled blasting prevents production delays associated with managing risks associated with wall instability. A method has been developed to quantify the drill hole deviation of presplit holes at Century Mine. Different controlled blasting techniques are used to control wall quality and decrease the risk. The performance of presplit drilling, in terms of deviation from design has been investigated. A methodology has been developed to quantify the drill hole deviation in three dimensions. This methodology was converted into a series of algorithms capable of handling an extensive range of data. The methodology was applied to a case study at Century Mine to evaluate the performance of drilling on two presplit blasts. Overall, 67 drill holes were investigated in the case study. The drill hole deviation was quantified in terms of three parameters: skewness, linearity and drill hole deviation parameter. Methods for quantifying each parameter were developed. Skewness, a measure of the amount of curvature and linearity, was defined as the measure of the consistency of the gradient of the drill hole. Drill hole deviation parameter is defined as the average measured deviation of the surveyed drill hole position from the design position. Acceptable drill hole deviation tolerances for each of the defined parameters were developed by analysing drill hole deviation parameters with respect to implications to catch berm capacity. Verification of the methodology was confirmed through the comparing of the completed drill hole deviation results using both visual inspection and cross analysis for each of the three methods. Holes with an R squared value of less than 0.97 for skewed deviation were classified as having skewed deviation, while holes with a difference in gradient of 3.5 were classified as having linear deviation. The results show that 76 per cent of the drill holes had deviation. Of this, 19 per cent were skewed, 57 per cent had linearity and 12 per cent contained both skewed and linearity deviation.

Nov 8, 2011

By A D. Campbell, G R. Power

The objective of the draw strategy in a caving mine is to maximise economic return by minimising waste dilution3 and maximising ore recovery4. The draw strategy must also include suitable controls for air blast and mud rush hazards and is highly constrained until continuous cave propagation has been achieved. This paper details a three-year project at the Ernest Henry Mine (EHM), which used cave flow simulation software to develop a draw strategy that increased the mine value by 32 per cent.Dilution and ore loss can be significant in sublevel cave (SLC) operations and result in poor recovery and considerable economic losses. To minimise dilution and ore loss, cellular automata software was used to simulate cave flow over the mine life. The optimisation project required mining footprints for various cut-off grades to be developed. Draw strategies for each mine footprint were then generated using a range of shut-off grades. Economic assessment of each scenario was then conducted to determine the mine footprint and corresponding draw strategy that generated the highest NPV (net present value). The iterative simulation process was improved by developing automated software functions in the flow modelling software to reduce time taken to generate and assess life-of-mine (LOM) draw strategy scenarios.In addition to improving the NPV of the mine, the optimisation project also enabled a decrease in the mine cut-off grade which increased the ore reserve and extended the mine life. Overall, an iterative process of mine planning, cave simulation, economic evaluation and geotechnical analysis was used to significantly increase the economic return of the SLC whilst ensuring caving risks were controlled to an acceptable level.CITATION:Campbell, A D and Power, G R, 2016. Increasing net present value by a third at an operating sublevel cave mine using draw strategy optimisation, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 167–174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By D Kent

"There has been a revolution occurring in underground mining over the last several years, where big headline items such as the Internet of Things (IoT), optimisation, managing data, data mining etc – the list of current catchphrases, goes on. In the end these are nothing new; but the ‘things’ (sensors) are becoming smaller, cheaper and easier to deploy, and the analysis much more powerful as computer processing speeds increase. However, to take advantage of the myriad of devices out there and gain the processing power to analyse and use the data, a reliable ‘conduit’ is needed for that information to be delivered where it can actually be used. That is, a high quality data network.Modern mining is like any other industry in the information age: the access to reliable data is the first, critical step in improving productivity (Stevens, 2015). The convergence of communications onto an IP (Internet Protocol) backbone has been the driving force in enabling the productivity gains in general industry over the last two decades.This paper overviews how this technology has developed as an enabler in accessing productivity and safety benefits, and how it has used access to large amounts of data to manage mining processes underground. Reams of data are useless, but with the reliable receipt, analysis, processing and feedback system in place to use that data, benefits can be realised.Automated mining systems are increasingly being seen as a key requirement for a productive mining operation, and the importance of an integrated communication network infrastructure to support such systems is growing. Another emerging driver is the much talked about IoT and data analytics, both dependant on reliable, accurate, high volume data.The author will outline how communication infrastructure is fundamental to the operation of such systems, and explain why the resultant communication networks require much more than just increased bandwidth (data capacity) to properly support the automation and other data hungry systems within the overall mine operation.Mining operations embarking down this road are discovering that the required network must be based on a true enterprise level architecture to, not only enable the mine’s current plans for remote or automated mining, but also to provide a scalable and integrated platform for future developments. The emerging issues for the communication network to truly support automation systems include: increased complexities of operating and maintaining multiple networks integration issues with disparate systems problems with reporting, particularly as demands for corporate reporting and compatibility with enterprise systems become the norm ongoing management challenges, which will only increase with the proliferation of new technologies.How certain mining operations lay the necessary foundations to meet their current requirements, while supporting their visions for a more automated and proactively managed mine, will be explored.CITATION:Kent, D, 2017. Modern mining – why bandwidth matters, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 123–128 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 16, 2017

By T N. Little

This paper is concerned with the influence of engineering geology on design of Wall Control Blasts. In the Introduction, the Blast Management Framework and the Blast Design Requirements classification system (previously developed by the author) is drawn upon to set the context. Blasting objective for all wall control blasts involves both profile and damage control. Four classes of approaches for blast design are outlined and briefly discussed. Five distinct wall control blasting techniques are summarised. The general relationship between geology and blast design is explored in the paper. Influence of geology on pre-split and post-split design and blasting direction is highlighted. Wall damage modelling from the closest row of blastholes is also introduced using the Analytical Damage Model (ADM). The relationship of rock properties and explosive selection and in particular the Mach wave generation is introduced to assist blast designer in this regard. Finally a Conceptual Model that relates vibration, damage and rock mass condition has been presented along with some applications that have been undertaken by the developer. Eight conclusions have been formulated based on extensive work in this area and the current study.

Jun 22, 2022

By W Russell, P Wighton, J Franke

Recent advances in ruggedised industrial control system technology and architecture in combination with latest technologies in the fast-evolving 3D LiDAR sensor sector becoming available have enabled the implementation of sophisticated automation algorithms for mining equipment such as bucket wheel reclaimers, as published by the authors in the peer reviewed AusIMM 2019 Iron Ore conference proceedings. This paper provides an overview of a second use case for such automation technology in bulk material ports integral to iron ore operations. The real-time 3D machine-vision based port automation system described in this paper was originally developed for the BHP-Mitsubishi Alliance’s (BMA) Hay Point port. The system has seen deployment at other major mining and general ports in Australia, such as at Dalrymple Bay Terminal (DBT) (shown in Figure 1) managed by Dalrymple Bay Infrastructure Management (DBIM), Hay Point, Queensland. It has the following use cases:

Nov 8, 2021

By T Burns, P Savory

In 2013, Rio Tinto Iron Ore (RTIO) produced 251 Mt from 15 mines in Western Australia. Throughout the mines, Ore Reserve models are used for long-term and medium-term mine planning. Grade control data aids the accuracy of short-term planning. Reconciliation of models with grade control data is important for maintaining confidence in predictions from the models, understanding the limitations of the models, and identifying issues that may require further work.There are a large number of sites and models, with more than 200 professionals involved in different parts of the reconciliation process. Regular meetings of all involved and enabling effective communication are important in the reconciliation process.Reconciliation data is gathered and processed through a web-based system; Grade Block Reconciliation System. This system cuts each grade block against the required model, stores the results, and allows users to view and analyse the data. Development of this system has occurred over a number of years and all Rio Tinto Iron Ore mine geologists and resource geologists now use it as standard to report reconciliation results. The results can be viewed in many ways including by different time periods or benches. Graphing the results assists identification of trends. Centralising and standardising reconciliation has allowed easier comparison between sites. Flexibility in the system allows users to customise reports to manage issues unique to their particular site.In parallel with system development, substantial effort has been put into ensuring mining professionals get together to discuss and understand reconciliation issues. To facilitate this there are now regular sessions, including site visits. Issues are assessed on a case-by-case basis and decisions on how best to address the issues are made by the relevant stakeholders. Reconciliation reports and action plans are revised each quarter.CITATION:Burns, T and Savory, P, 2014. Reconciliation of orebody model predictions – system and people, in Proceedings Ninth International Mining Geology Conference 2014 , pp 367–376 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014