Search Documents

By Harrison AT, Smart RM

Backfill systems using unconventional cementitious hinders have been successfully used in relatively deep and hard rock tabular mines for longwall, scattered stoping and shaft pillar removals. Two unconventional cementitious systems are discussed: 1. A ground granulated blast furnace slag (GGBS) with an activator containing lime. This has been used with a total tailings 'stable' slurry at a relatively low dosage of less than seven per cent, by mass, based on dry solids. The room and pillar stopes supported with this fill were up to 20 in high and the tailings were relatively high in pyrite. .\ GGBS binder plus a silicate based activator and gelling agent that virtually eliminated all water drainage (and hence post filling shnnkage). The system used a slurry, but the addition of the ;iutivator created a final placed product that had the behaviour of a paste. The system has been successfully used for almost ten years in the following applications: ò sloping widths (mining heights) above 1.6 in; and ò shaft pillar removals in seismically active areas at the end of the life of the shafts. \This paper discusses the technical merits and costs of the systems and compares them to other fill systems (including true paste systems).

Jan 1, 1998

By P McCarthy

The relatively new field of geo-metallurgy promises to improve the predictability of mill feed quality and enhance processing outcomes. However, it is subject to the same limitations as the prediction of grade using geostatistics and has additional limitations due to the spatial distribution of the variations being measured and the sample sizes required. Schedules based on geo-metallurgical models will, in turn, be subject to variations arising from geological control and practical mining constraints.This paper discusses the key drivers of variations in mill feed quality and quantity from a mining perspective. It concludes that geo-metallurgical modelling addresses only one aspect of the problem. A case study is provided to illustrate poor predictability of metallurgical performance even with very detailed geological data.

Aug 8, 2011

By A Cranley, A Giblett, S Thacker

The Newmont Tanami Operations are located in the Northern Territory, approximately 550 km north-west of Alice Springs. The Granites process plant commenced operations in 1986 as a 300?000 t/a ball mill / carbon-in-leach (CIL) plant and has undergone numerous expansions between that time and the current day, with project-to-date gold production exceeding 6.5 Moz. Annual plant throughput has exceeded 2.8 Mt/a while processing a blend of open pit material and ore from the Callie Deeps underground mine, with annual gold production exceeding 400 koz. In 2013 the operation processed 1.8 Mt of underground ore for the production of 323 koz of gold.This paper reviews the operation and expansion of The Granites process plant since the mid to late 1980s with particular focus on the gravity gold recovery circuit. The Tanami ores contain significant levels of free gold, and gravity recovery has long been an integral component of the metal recovery process at the Granites plant. The results of ten years of gravity circuit performance analysis and optimisation are presented.CITATION:Giblett, A, Cranley, A and Thacker, S, 2014. Three decades of gold production at the Newmont Tanami operations, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 209–216 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By D Hope, D Mitchell, B Metcalfe

In recent years there has been a major change among mining companies in their mining methods. This has been driven by the need to increase shareholder value and optimising the value from an operation. With this understanding there has been a need for all producers to become more efficient in their mining processes. An analysis of the coal losses at Mount Thorley Operations indicated that the major losses were in the dragline section of the mine due to coal damage from throw blasting. This damage was evident after the removal of the overburden by the dragline.Coal and Allied Mount Thorley Mine in partnership with Orica Explosives developed a process to reduce the coal loss associated with the throw blasting of Mt Thorley. Orica provided its specialised knowledge and experience in the drilling and blasting area and combined this with the local mining knowledge and expertise of Mount Thorley Operations personnel to conduct the project. This partnership reduced coal loss in excess of 50 per cent whilst maintaining targeted dragline productivity.

Jan 1, 2001

By R Pinksen

The Iron Ore Company (IOC) of Canada Mining and Operations Departments expressed an interest in reducing the amount of oversize material (>1 m × 1 m × 1 m) being produced and its subsequent downstream effects including in-pit sorting and reduction, damage to mobile equipment, and significant delays in the loading pockets and the primary crushers. To achieve this goal an oversize reduction project was undertaken by the mine and to date has significantly improved upon baseline measures.One key approach used to reduce the amount of oversize was the implementation of thicker emulsion. The introduction of a thicker emulsion into the blastholes provided more resistance to the forces created by dynamic water and reduced the infi ltration of the emulsion into the cracks and fissures of the rock mass. Blast results showed reduced amounts of oversize and more consistent fragmentation throughout the muck piles. Additionally, a significant reduction in nitrates leached into the mine water discharge has been realised.To determine the effectiveness of the oversize reduction project, IOC used shovel based camera technology to assess fragmentation presented to the shovel at the digging face. A digital vision system (DVS) was installed on one of the shovels to capture images that were stamped with global positioning system (GPS) locations. A large population of digital images was analysed to produce a robust fragmentation distribution baseline that was used as one of the mine key performance indicators (KPI). Changes to blasting practice were subsequently measured against the baseline KPI to assess effectiveness.

Jul 11, 2011

Determining the environmental consequences of green field projects is becoming an increasingly important component of new projects. Feasibility studies are regarded by potential investors as incomplete if a comprehensive Environmental Impact Assessment (EIA) has not been completed. These EIAÆs need to meet various local and international requirements in order to achieve bankability. Heavy mineral mining projects are often located in ecological sensitive coastal zones, and bring with them a suite of social impacts in the mainly developing countries within which they are usually located. This paper draws on experience gained in undertaking EIAÆs for heavy mineral mining projects in Kenya, Mozambique and South Africa, and uses these case studies to identify potential pitfalls. Important lessons include the need to initiate the EIA process as early as possible in the project, in order to develop management systems to mitigate the environmental impacts of exploration. Close and on-going consultation with affected communities is also seen to be critical to the success of the EIA. Proactive participation on the part of the environmental consultants with the project team and all interested and affected parties (IAPs) is important. An EIA commissioned later in project planning makes it difficult for the EIA to contribute in a positive manner to the project. Early engagement with environmental consultants allows the environmental assessment to develop from a report to an actual process, and to become fully integrated with project planning. The proviso is that an initial æfatal flawÆ assessment is required to identify any potential æshow stoppersÆ, in order to meet one of the important objectives of EIA, namely an assessment of whether or not the proposed project is the preferred development intervention in the study area. For more controversial proposals this may require the commissioning of a Strategic Environmental Assessment (SEA), which circumvents some of the limitations of the project level EIA. Whilst confidentiality is a constraint to full disclosure, an open participatory approach to public consultation is essential to add credibility to the EIA process and to gain, at least, the acceptance of the process from the majority of IAPs. Full disclosure is encouraged by organisations such as the International Finance Corporation, who acknowledge that good public consultation costs a lot of money, but bad public consultation costs a lot more! An open approach to disclosure presents understandable difficulties for proponents, as they are required to give up some of their control over the project, and to trust the social scientists engaged in the process. However, independence in the EIA process is critical to its success. This paper will highlight these and other issues by drawing on five case studies to identify lessons learnt, and explore the above themes in more detail.

Jan 1, 2001

Sishen uses a state-of-the-art tracking system to track material from its position in blast blocks through various stockpiles and crushers. Qualities are blended directly to the crusher as opposed to blending from stockpiles. This poses an interesting challenge to the planning department to simulate these conditions. The software used in these simulations are Whittle 4X and Maximiser for long-term planning, Xpac for medium-term planning and Mine Works Planner for short-term planning. Geological models and mine design layouts utilise Surpac. Sishen introduced Xpac a number of years ago; the system has developed and changed over the years. With the Sishen Expansion Project (SEP), which aims to utilise low-grade material, major changes to the planning process have to occur. SEP requires that the mine have two different plants, which utilise two different ROM feeds and have different beneficiation curves. Xpac is used to produce a rolling 18-month plan, which is as close to actual operations as possible. In order to do this, the simulations have to take into account the plants beneficiation curves, stockpile movements, hauling distance and equipment needs. On top of this, the schedule has to continually consider specifications for Fe and the contaminants. Plant yields also have to be kept within a certain bandwidth. Xpac is used to simulate the above parameters, as well as generate the raw data required to produce a mine budget. The paper will also show how the 18-month planning process and subsequent planning processes are measured and aligned. Xpac has proved to be an excellent tool to achieve these goals.

Jan 1, 2005

By C Samuelsson, Q Shu, A Lennartsson, F Gyakwaa, A Andersson, J Isaksson

The physico-chemical property, viscosity, is essential for pyrometallurgical processes and influences the settling rate of valuable metal droplets in slag, affecting the metal recovery. The copper slag from smelting furnaces typically contains between 1 and 2 wt per cent Cu, which equals to or is higher than in most sulfidic copper ores mined today, meaning the slag is a valuable resource for copper extraction. A low viscosity is desirable for slag-cleaning through a settling furnace where entrained droplets settle under gravity. One approach to control the viscosity is through the slag composition. The literature has limited data on the correlation between viscosity, slag structure, and optical basicity of iron silicate slag with FeO/SiO2, CaO, and Al2O3 as factors. Therefore, the present study evaluated the influence of these factors on viscosity and correlations with slag structure and optical basicity. The FeO/SiO2 ratio (at%/at%) and the CaO and Al2O3 content were altered in two levels, resulting in a two-level full factorial design with three factors. The study was done by synthesising FeO–SiO2–Al2O3–CaO–MgO–Cr2O3 melts, followed by water granulation. The melt structure of the samples was analysed with the help of Raman Spectroscopy. The viscosity was then estimated with a high-temperature rheometer using a Mo spindle and crucible. The results showed a correlation between the optical basicity, FeO/SiO2 ratio, and viscosity, where a high optical basicity and FeO/SiO2 ratio were beneficial for achieving a low melt viscosity.

Jun 19, 2024

By T N. Little

The aim of any rock breaking activity is to achieve success by developing designs that are blasting objective-specific and geology-specific, and then implementing such designs. This paper targets mining geologists with the aim of extending their knowledge of the rock fragmentation processes and providing insights to the significant relationships between geology and blasting. There are two main relationships, and if mining geologists appreciate both these relationships, then they can play a key role in optimising production. The business risk continuum is introduced to support this understanding. The first relationship is between geology and potential blasting hazards, and the operational complexity required to manage those risks. The risks associated with eight different ground types are discussed in terms of ground conditions, hazards and controls. These types are: reactive ground, hot ground, geothermal ground, fibrous ground, cavernous ground, combustible ground, pyritic ground and conductive ground.The second relationship is between the bench geology and blasting results. The blasting results discussed include: muckpile characteristics, remaining rock faces and blasting emissions. In this regard, some detailed insights and graphical examples are given for the influence of geology on blasting emissions, in particular, vibration, airblast and flyrock.A detailed description of the geological materials themselves can convey much useful information for blasting operators provided they are able to utilise this knowledge. Geologists are ideally suited to provide this description more effectively if they are familiar with the blasting process and the rock mass properties that influence blasting hazards and blasting results. It is also important to have clear statements of blasting objectives and associated operational targets, and this will maximise the likelihood of achieving the desired outcomes. The main aim of the paper is to highlight that geology is currently not fully utilised in the blasting process. In this regard, geologists are often not entirely aware of the blasting process and how they can contribute. The two significant relationships discussed above are integral parts of this process, and thus they are discussed as separate issues in the main body of this investigation.

Aug 22, 2011

By K Devencorn

The development of robust, economical transport infrastructure has been identified as a key driver to sovereign economic growth. Notwithstanding the value of undeveloped mineral resources, unless they can be brought to market they are of little value. Within a global context, the continent of Africa probably faces one of the most significant transport driven economic development programs as countries strive to unlock their much sought after resources.The UN’s Africa Review Report on Transport (United Nations Economic and Social Council, 2009) provides an excellent context for the issue facing African countries and the potential for investment in transport to solve many of the intrinsic problems they are confronted with. With little exception, economic development in Africa is very likely to be driven ‘off the back’ of transport development – and more specifically from heavy-haul rail as a means by which economic wealth can be derived from export of the continent’s vast natural and mineral resources to the world. The report found:transport is a key driver of economic development and poverty reduction;road transport is the most dominant mode in Africa;the ‘Cost to Market’ of African goods is hampered by the reliance upon road transport;the cost of road transport is not just economic – 19 per cent of the world’s road fatalities were recorded on African roads;African railways are seen to be disjointed and under-utilised;Africa’s ports are key to export trade - yet only six ports (three in Egypt, and three in South Africa) handle about 50 per cent of the continent’s total container traffic;the cost of transport is increasing making African trade even less competitive; andsignificant negative impacts of Africa’s reliance on road transport – health, and greenhouse emissions.We understand that mining the resource is only part of the solution – it has to be put to market at a competitive landed cost.Most African countries face huge costs associated with transport development and ongoing operation – in many cases beyond their available resources.The Australian rail industry has faced and solved many of these challenges.

Nov 22, 2011

By A Gustafson, D Johansson, K Jonsson

The underground mining process, from in situ characteristics of the unmined rock mass to the final mill product with fully liberated minerals, consists of a chain of unit operations. Some of them influence fragmentation while fragmentation impacts others. From a production point of view, fragmentation is a key parameter for the proper functioning of many unit operations and affects total production; it influences the ability to load, haul and crush the rock later in the process. Fragmentation varies because of rock mass strength, the presence of joints, the chosen explosive, specific charge (kg/m3) and quality of drill holes. The efficiency and result of unit operations such as drilling, blasting, loading and crushing depend on the rock properties, which vary throughout a mine. Generally speaking, operations are not well adapted to the actual rock properties, leading to a non-optimised flow in production. This paper presents the initial part of a project that will build knowledge on the impact of fragmentation on each step of the production chain in an underground mine. It identifies the key parameters of fragmentation, which influence the overall energy consumption and productivity in a mining operation through interviews, mine visits and a literature review. In the subsequent stages of the project, a number of field tests in the case study mine will address important segments of the production process where fragmentation is a major obstacle to improvements. Optimising the entire process, rather than isolated unit operations, will lead to increased productivity, decreased amount of interruptions and lower energy consumption.CITATION:Gustafson, A, Jonsson, K, Johansson, D and Schunnesson, H, 2016. From face to surface – a fragmentation study, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 555–562 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

For too long we, as an industry, have borne the brunt of irrational claims, poor science and even worse, journalism with regards to our affect on the environment. To some of us, the overwhelming media attention on greenhouse warming, the polluting outputs of mineral processing or unthinkable depletion of natural resources has left us embarrassed and more unfortunately has turned bright young people away from a career in the minerals industry.This paper shows the hypocrisy associated with an element of the green movement and dispels some general myths on mining disseminated by radical environmentalists.The fallacy of the greenhouse warming effect will be scrutinised by common sense and the mining industryÆs use of land will be discussed and put in proper perspective.Problems associated with safety and emissions and the means to overcome such are discussed briefly.

Jan 1, 2004

By A Bagis

Road tunnels are an accepted and effective transportation solution in urban areas to mitigate increasing traffic congestion and facilitate improved urban connectivity in a cost effective manner while meeting societal goals to reduce the impact of construction. In designing a tunnel system, there is a requirement to achieve an acceptable level of in-tunnel air quality, as well as meeting ambient air quality goals. In Australia, there is also a requirement for zero portal emissions which means that all pollutants must be emitted to the atmosphere via a ventilation stack.Traditionally, effective pollutant dispersion has been achieved by constructing tall ventilation stacks which disperse pollutants into the atmosphere at a high level. The dominant variable parameters in the effectiveness of the dispersion under the ventilation engineers control are the efflux velocity, the height of the ventilation outlet and the concentration of pollutants at the point of discharge. During off-peak operations the required ventilation exhaust rate can be reduced due to the decrease in traffic. This can lead to a drop in the efflux velocity from the stack and therefore the effectiveness of the dispersion. This potentially drives the need for a higher outlet, or an increased exhaust rate to achieve a higher efflux velocity with consequent effects on energy consumption.The paper proposes a method of varying the cross-sectional area of the ventilation stack with the use of motorised control dampers, thereby maintaining a sufficiently high efflux velocity throughout the 24 hour period independent of traffic conditions. This allows the use of a potentially shorter ventilation stack.

Mar 8, 2011

By B Murphy, S O’Connell, J L. Heath

In the 1989 best-seller The 7 Habits of Highly Effective People, the author, Stephen Covey, highlights the importance of maintaining not only ‘production’, but also, ‘production capacity’. When operating a modern flotation concentrator, production is often measured in terms of concentrate tonnage, tonnes milled and plant utilisation. There are very few metrics that focus directly on flotation equipment condition in relation to performance, which is analogous to Covey’s production capacity principal. It is evident on many mine sites that flotation equipment condition is not monitored on a proactive basis and that the prevailing culture is to wait for a failure, before addressing an issue.This paper discusses examples of how poor equipment condition can lead to production loss through poor metallurgical performance. Actual examples are given where these problems have occurred in operating plants. An outline is provided on how metallurgical and maintenance departments can work together to protect production capacity and gain more from existing equipment.CITATION:Murphy, B, O’Connell, S and Heath, J L, 2014. Maximising value through maintaining your flotation equipment, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 71–76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By P Revell, G Wilkie, P Walters, L Keeney, F Faramarzi

Grade Engineering® is a value-driven strategy aiming to maximise benefits by exploiting intrinsic grade variability of ore deposits. It utilises a multitude of separation techniques to remove low grade material before being introduced to post-blast size reduction processes, i.e. crushing and grinding. At an operational scale, Grade Engineering® techniques can be implemented at the drill-and-blast stage, to control the degree of fragmentation in accordance with the spatial distribution of valuable minerals across an ore domain through differential blasting. It can also exploit intrinsic textural and breakage characteristics of a given ore type to reject uneconomical barren material at coarse sizes, which is known as Natural Deportment. Grade Engineering® can also be employed in the deliver stage of the mining value chain through sensor-based bulk and particle sorting. Each strategy is therefore highly dependent on the responsiveness of an orebody to available techniques. That is, the extent to which Grade Engineering® drivers would be capable of unlocking potential values of currently un-amenable orebodies depends on how detailed the heterogeneous nature of ore domains can be described. This paper considers exploring possible linkages between deportment characteristics of an ore and its competence when broken in a range of energy inputs at a particlebased level. Accordingly, potential opportunity may lie in exploring whether the intensity of input energy (or degree of fineness) can be used as a lever to improve or ‘unlock’ ore amenability to Grade Engineering® techniques. Implications from such a detailed approach offers new opportunities to enhance Grade Engineering® gains through engineering ore competence variability.

Nov 10, 2020

By R Berry, A Escolme

"Predictive geometallurgical models are being developed for the Productora Cu-Au-Mo deposit based on geochemistry to reflect variability in Cu species based on Cu sequential leach data (ie oxide, transitional-oxide, transitional-sulfide, sulfide and non-recoverable Cu).Productora, located in the coastal range of northern Chile, is a magmatic-hydrothermal tourmaline breccia-hosted, structurally controlled Cu-Au-Mo deposit hosted by a thick sequence of Jurassic rhyodacitic volcanic rocks. North and north-west striking fault sets control the distribution of mineralised breccias. Alteration is widespread, complex and pervasive. Hypogene alteration assemblages range in composition from distal magnetite-amphibole, to sodic-calcic, to sodic, to phyllic, to proximal potassic. Low-temperature advanced argillic assemblages are locally juxtaposed next to proximal high-temperature K-feldspar-tourmaline assemblages. The dominant hypogene Cu phase is chalcopyrite.A simple Cu species classification scheme based on sequential leach data and S per cent was devised to account for non-recoverable Cu (ie non-sulfide Cu), which is insoluble in weak acids. Through machine learning, a proxy for this Cu species classification scheme was developed based on: depth, Ca per cent, Cu per cent, Fe per cent, K per cent, Mn ppm, S per cent and Ln(Cu/S) plus logged regolith class, thus allowing classification to be extended to areas of the deposit where no sequential leach data are available. The modelled data has been used to generate deposit-wide 3D models for Cu species classification.The validity of the proxy Cu species classification model is being tested against the results of flotation analysis. Initial results indicate that geochemical proxies can be used to successfully predict Cu species class and provide a high density of classification data.CITATION:Escolme, A, Berry, R and Hunt, J, 2016. Predicting Cu Species Classification Using Geochemistry at the Productora Cu-Au-Mo Deposit, Chile, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 113–118 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By M Schaffer, T Kewe, N Moffatt

Porgera mine is 95 per cent owned by Barrick Gold Corporation. It is located at an altitude of 2200–2700 m above sea level in the Enga province of Papua New Guinea and produces approximately 460 000 oz per annum with a proven and probable reserve of 6.2 Moz. The refractory ore is ground in a conventional semi-autogenous grinding and ball mill circuit. After the gravity gold is recovered, the slurry is floated, oxidised in the autoclaves and then leached. This paper will focus on the flotation circuit and the recent upgrade of the control system. The five interdependent flotation circuits were challenging for operations to control as they dealt with variable grade, throughput and circulating loads, as well as the physical limitations of the equipment. With the installation of 18 Portage Froth Characterization® (PFC) cameras, the plant’s operation has been converted from a level-control based strategy that was focused on individual cells to one that targets grade and recovery control across the entire circuit. Variability in feed and the corresponding launder issues were addressed with a unique site initiative of deflector plates to indicate filling level. Non-linear closed loop control was implemented directly in the DeltaV Distributed Control System (DCS) using Portage Advantage Regulatory Control (PARC) algorithms and optimised with AwaRE advanced controllers. The most noticeable benefits achieved with the upgrade include improved flotation gold recovery, consistent flotation sulfur grade and autoclave performance. Correspondingly, there was a significant drop in boiler diesel fuel usage and launder overflow conditions.CITATION:Kewe, T, Moffatt, N and Schaffer, M, 2014. Porgera flotation circuit upgrade and expert system installation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 345–356 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By T Walkemeyer, R Elliott, D Chang-Martin

Over the past decade, discrete element method (DEM) simulations have seen increasing adoption by the resources sector to inform the design of materials handling equipment such as transfer chutes, bins and hoppers. But, if ‘all models are wrong, but some are useful’ (Box, 1979) what approaches are available to check that a DEM simulation is useful? How to avoid garbage in equals garbage out. This work considers what properties of bulk solid flow behaviour are important to transfer chute simulation. Cohesive bulk solids (such as sticky iron ore fines) can develop sufficient strength to form a stable cohesive arch, this phenomenon is not well predicted by measurements of angle of repose. This work presents a two-part approach to the development of a useful DEM model that can be used to add value to the design and optimisation of bulk materials handling equipment. Part 1 is the calibration of not just one, but a range of material models chosen to envelope the range of anticipated materials that will be handled. This work describes the DEM simulation of a batch of direct shear cell tests to develop material models that can be measured by the same metrics routinely used to characterise the flowability of cohesive iron ore fines. Part 2 of this work describes systematic methods for validation of the transfer chute DEM simulations. The DEM model is only useful if it can adequately represent the typical problems observed within a transfer chute, such as blockages due to build-up and cohesive arching. Proper validation requires good observations. Validation examples of site observations are shown side-byside with simulations to demonstrate the adequacy of the DEM model and calibration approach. DEM simulations have the potential to add significant value by allowing engineers and designers to predict material flow-through equipment based on a range of material properties, allowing for stress testing designs and making iterative improvements.

Sep 18, 2023

By J P. Evert

Didipio gold-copper mine operation is situated in the island of Luzon, approximately 270 km north of Manila in the Philippines, in an area of high seasonal rainfall. The hydrogeological water flow model implied that there would be high connectivity between regional structures and underground operations. This model predicted that underground mine groundwater inflows were expected to quickly rise as the decline progressed to a peak of 510 L/s. Designing a capital pump station to deal with 510 L/s has its own challenges, however developing the decline down to the required level, always dealing with 300 L/s of water and constructing the pump station is extremely challenging and required a robust water management plan and mine design. When dealing with expected high volumes of water, underground mine design and scheduling plays a key role in protecting electrical infrastructure, equipment, secondary pumps, and the decline from flooding. A good drainage system and controlled dewatering plan is essential for safety and progress. This paper details the dewatering techniques and mine designs required to accomplish decline development with high water inflows as used in the Didipio project. It will describe the learnings and outcomes that are achievable with a flexible design, as new structures are mapped, and water intersections are increased. It also highlights the potential for adaptability in mine planning to provide evolving improvements or to evade problems that are expected from the constant reconciliation of data recorded during development.

Mar 29, 2023

By M Gasparon, J Harris, T Baumgartl, D J. Williams, M Edraki, P A. Kirsch, D Rowe

RISKGATE, an Australian Coal Association Research Program-funded (ACARP) initiative, has been designed to assist the Australian coal mining industry in improving minimum standards for safety performance, efficiency, operating practice and training. The online system is innovative in that it is built upon a foundation of industry expert knowledge gathered through action research workshops, which is further supported by a broad array of industry, academic and technical resources. In operation, RISKGATE offers a continuum for knowledge transfer and communication of current practice in risk identification, assessment and management in the coal mining industry. The primary mission of RISKGATE is to focus industry attention on prioritising control management as a way to achieve acceptable risk.A Coal Mine Tailings Dam Module has recently been added to the RISKGATE suite. The key risk, or initiating event, associated with coalmine tailings dams is catastrophic failure of the dam, leading to the release of tailings and water. This can occur due to geotechnical instability of the dam itself or of its foundation, overtopping and erosion of the dam, and piping failure of the dam itself or of its foundation. Coalmine tailings dams are also prone to seepage into the foundation and through the dam, particularly during operation when large volumes of water are discharged with the tailings. The most significant risk associated with seepage is the release of potentially contaminated water to the environment. Contamination can take the form of elevated salinity, acidity and dissolved metals. Run-off from coalmine tailings can cause erosion and can also potentially contain contaminants. Desiccation of the tailings surface can result in dust generation and dispersion.The paper presents the background and context of the RISKGATE project, the need for the addition of the RISKGATE Coal Mine Tailings Dam Module, and a description of the developed module, including the five initiating events considered, their causes and associated preventive controls, and their consequences and associated mitigating controls. This paper concludes with a discussion of the ways in which Australia’s coal mining companies are starting to apply the RISKGATE body of knowledge at their sites, which will flow onto the management of their tailings dams.CITATION:Williams, D J, Kirsch, P A, Gasparon, M, Baumgartl, T, Edraki, M, Rowe, D and Harris, J, ?2014. Application of RISKGATE to coal mine tailings dams, in Proceedings Life-of-Mine 2014 , pp 219–230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014