Search Documents

By G Simpson, S Dressler, A E. Levett

Tailings storage facilities often represent a mining operation’s most significant liability, posing serious environmental, social and safety risks. Almost all mining operations dispose of wet tailings (Valenta et al, 2023), which represents a risk of failure due to the potential for a rapid strength reduction of the unconsolidated materials leading to static liquefaction and subsequent dam wall failure. As a waste stream, tailings disposal, decommissioning and relinquishment aim to be inexpensive processes, ruling out many highly engineered solutions. Advantageously, tailings consolidation does not need to be immediate, opening the door for relatively passive, inexpensive consolidation methods that aim to gradually increase the strength of tailings over extended periods (ie years). In this paper, we present the prospect of novel in situ tailings stabilisation, learning from studies that have investigated the most erosion-resistant landforms on Earth.

Aug 2, 2023

By A G. Sheard

Fire safety requirements inside tunnels have become more demanding as tunnel designers consider the impact of potentially larger fires. Tunnel ventilation equipment is required to clear hot gases in the event of a fire. This is vital to maintain smoke free escape routes for people trapped in the tunnel and to facilitate safe access for emergency services. As the fire becomes larger, the temperature of clearing hot gases increases. Traditionally, engineers have taken into consideration gas temperatures of 250°C when designing tunnels. Because of larger fires, engineers must now design equipment to clear hot gas up to 400°C.Increasing the temperature of hot gases to 400°C requires tunnel ventilation equipment that goes beyond historic limits. As temperature rises, material strength reduces, consequently mechanically constraining fan aerodynamic performance. Developing tunnel ventilation equipment suitable for clearing hot gases at 400°C requires a fan technology that is more typical of industrial turbomachinery. The standards EN 12101-3:2002 and ISO 21927-3:2006 defi ne the necessary design criteria and testing methodologies to verify that a range of tunnel ventilation equipment is capable of extracting hot gases.This paper describes the process by which the authors certified in accordance with EN 12101-3 and International Organization for Standardization (ISO) 21927-3 a range of powered ventilators suitable for clearing smoke and hot gases at 400°C for two hours. Proving the high temperature capability of the new range provided a challenge as a consequence of the large physical sizes and high motor powers involved. Additionally, the need to install vertically, as well as horizontally, imposed high thrust loads on motor bearings, further complicating both mechanical design and testing. The paper presents the methods by which the authors overcame these challenges.

Mar 8, 2011

By Nilmani M, Malone J, Taylor RN, Floyd JM, Gray NB, Fountain CR

CSIRO staff and University of Melbourne staff and students collaborated in an intense programme of investigation on the CSIRO 50 kg Sirosmelt pilot plant.In two days of operation copper matte converting and zinc slag fuming trials were performed, whilst investigation of the process dynamics and process chemistry was carried out. This exercise is an example of the techniques available for process evaluation, which can rapidly advance the understanding of pyrometallurgical operations by use of a team approach covering a wide range of experiments.

Jan 1, 1985

By E Coffison, M Gibbs, C Bennett

The sustainable management of surface water associated with coal mining and coal seam gas projects is a considerable factor affecting the global competitiveness of these resource companies operating in Australia. Management of surface water can be costly, but effective water management and hence environmental stewardship enhances corporate social responsibility and the social license to operate. The surface water issues for the two industries are comparable, yet there is currently a lack of alignment between how Queensland, where the majority of AustraliaÆs coal seam gas projects are located, manages and regulates water on coal mine projects and coal seam gas projects.This paper provides a high level comparison of Queensland legislation and highlights the lack of alignment of this legislation regarding surface water management in these two industries. Through a case study, it looks at the surface water management process at a coal mine site based on the current legislation and principals of surface water management. QueenslandÆs lack of alignment in legislation regarding surface water management in these industries is understandable given the different development paths and time scales of the two industries. The coal mining industry has developed over a long period of time and the legislation has progressed in parallel, whereas, the coal seam gas industry is relatively new in Australia and the legislation has had to advance quickly. The lack of alignment between management of surface water for the two industries creates confusion among stakeholders and this adds complexity and additional transaction costs during the exploration, permitting and operational phases of projects, including landowners who may be affected.CITATION:Bennett, C, Coffison, E and Gibbs, M, 2013. Lack of alignment between regulation of surface water management in coal mining and coal seam gas, in Proceedings Water in Mining 2013 , pp 157-162 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By A G. Shellsh, R J. Henham, J R. Foley

The Porgera Gold Mine, west of Mt Hagen in PNG is a large open pit and underground operation currently producing gold at the rate of almost one million ounces per year. This deposit has produced some 8.8 million ounces to-date and has current reserves of 103.4 million tonnes @3.2 g/t Au. The Porgera Joint Venture has invested over $A1 billion in infrastructure in this project. Technical management of this operation involves the interrogation of some 700 000 metres of diamond drilling, some 50 000 blastholes per year, and very large volumes of laboratory, geotechnical, environmental and production reporting data. Over the past seven years this data has been consolidated into a single centralised, relational database which now acts as the single reference point for all the technical application systems used for surveying, grade control, production reporting, deposit evaluation and modelling. Data transfer to application programs and management systems is controlled by the centralised database, this process at times involving a two-way, real-time, binary data transfer. The benefits of a specialised database application include security and integrity of the data asset, ease of access, and performance in a multi-user environment. This replaced fragmented, inconsistent data sets stored inefficiently as individual, unindexed, variably formatted files associated with the different application programs. Most importantly, the database has allowed mine management at all levels to make timely, confident investment, cash flow and optimisation decisions as it provides the primary link between the deposit and operational data sets on one hand, and the application programs and management and performance measurement systems on the other. This paper discusses the economic value and importance of technical data in terms of the resource asset and the means by which this data is being managed and used at Porgera.

Jan 1, 2000

By A C. Robertson

Over the past decade there has been continual change in the way that mines have been managed and the component roles of those people who make up the total mine management system. Major issues have included the change in the business structure of mining companies, the change in on-site infrastructure, increased personal liability of managers for the safety and health of employees and increasing social and environmental pressures on managers and their staff. This paper looks at the changing roles of two of the many groups of professionals associated with the mining industry - the equipment supplier and the mining consultant. The profiles of the ACME Group Pty Ltd, suppliers of ventilation equipment and ancillary canvas and plastic products to the mining and construction industry, and Tennent, Isokangas Pty Ltd, Consulting Mining Engineers, are presented.

Jan 1, 1998

By G L. Simmons, K M. LeVier, R Kappes

The low potential hydrophobic state of pyrite in amyl xanthate (PAX) flotation with nitrogen is of particular interest with regard to the N2TEC flotation technology currently being used for the recovery of auriferous pyrite at NewmontÆs Lone Tree Plant in Nevada. Initially, the N2TEC system had been found to operate satisfactorily, but cyanide in the flotation mill water appeared to be responsible for a loss in pyrite recovery. This supposition was confirmed with laboratory experiments, and a program was initiated to study flotation chemistry variables by electrochemically controlled contact angle measurements. Experimental results show that activation of pyrite in such cyanide solutions can be achieved more effectively with lead than with copper. Subsequently, based on these fundamental studies, significant improvement at the Lone Tree Plant was achieved by lead activation, in which case the recovery increased to expected levels. The effect of activator is particularly significant not only with respect to pyrite depression by residual cyanide, but also with respect to collector (PAX) consumption and the initial state of the pyrite surface. Experimental results show the importance of the pyrite surface state and the rather interesting features of the activation process.

Jan 1, 2005

By D Wyborn, P A. Dowd

The characterisation of rock fracture networks is an important component of rock engineering applications involving stability assessment or fluid flow analysis. However, the derivation of a reliable rock fracture model remains a very challenging problem in practice. This paper describes a Bayesian framework, in the form of Markov Chain Monte Carlo (MCMC) simulation, for the construction of such a model. Model conditioning using different data sources is discussed including seismic events recorded during hydraulic fracture stimulation, rock face fracture mapping data and downhole geophysical survey data. The freeware FracSim3D is used for the simulations.

Sep 26, 2011

By N Maistry, C Carelse, A Singh

Banded Iron Formations or more commonly known as BIF are sedimentary rock formations with alternating silica-rich layers and iron-rich layers that are mainly composed of iron oxides (hematite and magnetite), iron-rich carbonates, and/or iron-rich silicates. Considering the depletion of highgrade iron ore reserves in South Africa, there is a need to maximise resource utilisation through the exploitation of low-grade/uneconomic resources particularly BIF material, which makes up more than 65 per cent of current reserves. Previous test work conducted by alternative BIF sources globally indicates the need for fines processing in order to produce a concentrate. South African BIF however is amenable to coarse and fines processing producing an on-grade product or blended feedstock. C-Type material within South Africa’s Northern Cape Province grading at approximately 33 per cent Fe was supplied for research purposes. Top size optimisation via gravity Heavy Liquid Separation (HLS) tests was conducted. The laboratory results being perfect separation (Ep=0) were modelled to predict pilot performance, the results of which were tested on a pilot scale for the finest size fraction (-1 mm). It was observed that a top size of -2 mm provided optimum results in terms of upgrade and recovery, with crushing finer not necessarily producing superior results. At a target grade of 60 per cent Fe, recoveries of 65.6 per cent were achieved on the laboratory scale, whilst recoveries of approximately 58 per cent were achieved on the pilot scale. Targeting higher upgrades of 63 per cent would inevitably result in lower recoveries of 57.2 per cent on a laboratory scale and approximately 54 per cent on a pilot scale. This is in line with grades and recoveries achieved globally for BIF material albeit at finer grind sizes.

Sep 18, 2023

By Y Mita, T Iwama, R Inoue, S Ueda

In the iron and steel manufacturing industries, efforts are being made to achieve carbon neutrality by 2050, and the transition from a coal-based steelmaking process to that utilising renewable energy is being pursued. An alternative process in which directly hydrogen-reduced iron is melted in an electric furnace is being investigated. It is known that foaming slag reduces heat loss from the steel bath in electric arc furnace, but iron loss due to the suspension of steel particles in the slag is indispensable. To improve the separation of steel particles from the slag, the control of the slag viscosity is important. Although the slag viscosity has been extensively studied, in those studies the slag was considered to be a simple liquid. However, in actual operations, slag is a multiphase fluid consisting of solid, gas and liquid phases. Therefore, in this study, by measuring the sedimentation velocity of titanium, stainless steel and glass spheres in an aqueous glycerin solution containing bubbles generated by the reaction between NaHCO3 and C2H2O4, the apparent viscosity of the gas-liquid fluid was evaluated based on Stoke’s law. It was found that the apparent viscosity of the gas-liquid fluid is larger than the viscosity of liquid phase and depends on both the bubble volume ratio in solution and the density of the falling solid sphere, and the apparent viscosity was different from that previously obtained by the rotation method. The apparent viscosity derived from the sedimentation velocity of solid spheres changed depending on the specific gravity of the ball. This is because the apparent viscosity is derived from the velocity of a ball falling in a static bubble in this method, whereas that is derived from the force applied by a stationary flow in the rotational method.

Aug 21, 2024

By K Dagdelen, I Traore

This paper presents an iterative net present value (NPV) maximisation method to determine the optimum surface to underground transition depth for an orebody to be mined by multiple open pits and an underground mine. The determination of transition depth from open pit to underground mining is based on global production scheduling optimisation of open pit and underground mines using mixed integer linear programming. The method is applied to a case study coming from a gold mining complex with six open pits and a large underground mine using longhole open stoping. The results indicate potential improvements of the NPV of global operations when compared to the traditional techniques based on independently optimised open pit first, followed by underground mining.CITATION:Dagdelen, K and Traore, I, 2014. Open pit transition depth determination through global analysis of open pit and underground mine production scheduling, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 195–200 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By D Maldonado

BlueScope Steel’s Port Kembla sinter machine underwent a major upgrade during mid-2009. The mixing and rolling drum (MRD) was thoroughly cleaned during the upgrade. Space factor measurements taken in October 2009 showed that the drum was operating in the cataract regime in the dry mixing section and the cascading regime in the rolling section, which is optimal for granulation. Sampling carried out during an entry into the MRD showed that both the Sauter mean diameter and the predicted bed voidage increase rapidly during wetting, and then decrease in the wet mixing section. In the rolling section, the granule properties remained constant untilthe drum discharge. Frozen particle analysis, using liquid nitrogen as the quenching agent, were carried out on material collected from the MRD discharge. The results, expressed as a Granulation Index, showed there had been a significant improvement in the granulating performance of the MRD following the upgrade. The plant studies were also complemented with laboratory scale experiments which aimed to optimise the granulation process. The effect of burnt lime on green feed permeability was quantifi ed using the laboratory scale drum at different moisture contents. A significant increase in permeability was apparent once the burnt lime dosing rates doubled from 1.1 - 2.2 per cent w/w (feed basis). The capacity of the burnt lime system at the sinter machine will be increased in order to benefi t from the expected higher permeability, permeability, which will enable the machine to sinter at deeper bed heights.

Jul 11, 2011

By J Manuel, N Ware

Ideal iron ore sinter is produced by optimising the balance between coarse (+2 mm), stable ore nuclei and a reactive matrix consisting largely of fluxed -1 mm fines. The authors have previously published work evaluating the matrix melting behaviour of a number of fine ores, using techniques developed by CSIRO. The focus of that work was to demonstrate the contribution of the matrix to overall sinter quality, with the results showing a direct correlation between melting point, matrix porosity and strength. CSIRO has also developed a complementary test to study the behaviour of coarse ore nucleus particles in contact with the sinter matrix and provide an evaluation of their reaction and assimilation properties. This test provides valuable fundamental information that can be used to better understand the role of specific ore types and optimise blend composition.The CSIRO laboratory-scale assimilation test is carried out by embedding particles of ores of specific sizes into a fluxed matrix of known sinter blend composition, using real ores and fluxes, in a laboratory test that directly relates to pot-grate and plant sintering conditions. Samples are fired under controlled conditions in a tube furnace using a standard heating profile and a constant, low-oxygen potential atmosphere. These conditions simulate the actual sintering process while removing the effects of the many locally-variable parameters (eg temperature, oxidation potential and localised chemistry) that exist in the actual process, meaning that trends in behaviour can be more clearly seen. Designed as a compromise between the industry-standard pot-grate sintering test and a more fundamental test using chemical reagents, the aim is to isolate and evaluate the nucleus behaviour of an individual blend component to allow an improved understanding of the role that an individual ore plays in a specific blend. Measured cross-sections of the resulting fired samples provide a semi-quantitative measure of reactivity, while accompanying photomicrographs allow a qualitative assessment of assimilation properties (eg volume and distribution of secondary porosity generated during reaction).In this paper, to complement the previous work published on melting behaviour, nucleus particles were selected from hematite, hematite-goethite and goethite ores and embedded in a simulated plant sinter matrix. Drilled core particles of two sizes were tested at fixed temperatures simulating low- (<1300°C) and high-temperature (>1300°C) sintering conditions. The resulting assimilation properties are compared and discussed as a function of particle size, temperature and ore/sinter mineralogy. The implications for the contribution of each component to the prediction of blend sinter quality are also discussed.CITATION:Ware, N and Manuel, J, 2015. Fundamental nucleus assimilation behaviour of hematite- and goethite-containing ores in iron ore sintering, in Proceedings Iron Ore 2015, pp 77–82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By J Q. Shi, M Karakus, Y Liu

Predicting the spatial distribution of rock mass properties in cave mining is a critical challenge. In this study, we introduce a novel machine learning-based model to advance our comprehension of rock behaviour. This model specifically focuses on the spatial distribution of rock mass and mechanical properties, a crucial aspect of our understanding of rock mechanics. Our model is inspired by the recognition that neighbouring information serves as crucial prior knowledge for predicting the spatial distribution of these properties, wherein closer neighbours are likely to exhibit similar characteristics. To effectively capture and model these neighbour relationships, we design a neural network-based model to map the spatial locations within the data set into a new highdimensional space. Within this transformed space, we utilise Euclidean distance to identify N neighbours. Leveraging these neighbours, we introduce a straightforward yet highly effective approach—label propagation—to construct a graph that illustrates neighbour relationships. This graph not only facilitates the prediction of the spatial distribution of rock mass properties but also offers a measure of uncertainty for these predictions. We validate the proposed method using a real rock data set and showcase its efficacy in capturing intricate relationships and distributions within rock properties, enabling precise predictions across diverse spatial scales. Our results underscore the potential of machine learning-based approaches to revolutionise the field of rock mechanics, providing valuable insights applicable to geotechnical engineering, mining, and other sectors where an accurate understanding of rock properties is paramount. This model has direct practical implications, offering a new tool for geotechnical engineers and mining professionals to enhance their understanding and prediction of rock properties, thereby improving safety and efficiency in their operations.

Sep 1, 2024

By M Iglesias-Martínez

The potential for iron ore in the Central African Archean belts has received much less attention by comparison to their equivalents in other cratonic regions of West Africa, South Africa, Australia and Brazil. Historically, iron ore is known to occur in South Cameroon and North Gabon with significant iron ore deposits (eg Mbalam in Cameroon, Avima in the Republic of Congo, Minkébé, Bélinga and Boka-boka in Gabon), having been the subject of geological exploration programs carried out by government institutions and exploration companies. Although the presence of strong aeromagnetic anomalies, undeniably related to the presence of greenstone belt formations, has been recognised, this study is the first attempt to assess the potential of banded iron formations (BIF) in the Northern part of the Gabonese Republic in the region between Minvoul and Minkébé (>10.000 km2). Deep lateritic weathering, inaccessible equatorial rain forest and high operational costs are some of the reasons why only limited exploration has been undertaken in the area. This work aims to improve the geological knowledge and to highlight the potential for iron ore of the eastern margin of the Ntem Complex units dated between 3.3–2.7 Ga. Field work showed a series of mafic rocks (amphibolite, anorthosite and gabbro), schist and BIF (described as itabirites in neighbouring areas). Samples from Minvoul BIF showed an extensive and deep weathering to powdery hematite revealing the presence, in thin sections, of iron oxides including magnetite, hematite and martite, primary and secondary quartz, garnet, hornblende, anthophyllite, cummingtonite and epidote. Mineral assemblages and coarse grain size suggest a metamorphic grade ranging from medium to upper amphibolite facies. The existence of known economic iron ore deposits in neighbouring regions combined with an extensive weathering enrichment process are promising factors for potential iron ore discovery in this remote area.

Sep 18, 2023

Although a formal EES was not prepared for the WIM project due it winding down, CRA Ltd has been through the EES and planning scheme amendment process for its demonstration plant. Community consultation was involved with all aspects of this process. The paper outlines the WIM EES consultation program and provides lessons for future community consultation for major projects in regional locations with significant potential to alter the environment.

Jan 1, 1992

By K Clode, J Al-Shdifat, S Daykin

Planning for a circular economy allows for previously untapped market opportunities to be explored, resulting in new, innovative revenue generating opportunities, while also reducing environmental impacts. In particular, rare earth elements (REE) are in rising demand as they are key components of over 200 products across a wide range of applications (Xie et al, 2023) including renewable energy technologies. There is a geographical disparity in deposits, with China being the top producer, generating 70 per cent of global production in 2022 (Laboure, 2023). This single dominating source has created supply chain concentration and hence supply risks for other nations, providing a driver for finding alternative sources, such as mine-influenced water (MIW) and tailings. In this study, Isle presents a robust due diligence methodology for undertaking a global horizon scan into REE recovery technology, for a large mining company, from tailings decant water on a specific site. Previous studies of the tailings decant water at this site had shown potentially significant concentrations of both heavy and light REE, but challenges such as high flow, very low pH and high concentrations of iron had previously made recovery unfeasible. Due to these challenges, the horizon scan focused on technologies that had the potential for selective recovery, despite the challenges with water quality, and considered a range of Technology Readiness Levels (TRLs). This included an adsorption-based process that has the potential to selectively separate individual REE, and a polymer based selective flocculation technology.

Sep 1, 2024

By C Sennersten, A Hellicar, C Lindley

Traditional methods of resource modelling and mine planning rely upon geostatistical methods applied to exploration drill core data to derive a three dimensional model of the distribution of metal grades, quantised into rectangular prisms or blocks. The resulting block model is a primary input into short, medium and long term mine planning. However, block attributes are averaged or interpolated over a complete block, meaning that information at smaller scales is lost to the mine planning process. Grade engineering for new mining methods, such as the development of more accurately controlled blast designs, continuous miners for hard rock and sensors for rock properties that can be distributed along the operations process and value chain, allows excavation to be much more selective than traditional blasting, and provides data for driving earlier separation of waste from ore. This selectivity can be optimised if the resolution of resource models can match or exceed the spatial resolution of selective mining technologies. Opportunities for selective mining increase as a deposit becomes more heterogeneous. This leads to an interest in methods for estimating the distribution and characteristics of mineral heterogeneity within the ore-body. The objective of this work is to present some definitions of mineral heterogeneity, and to explore how heterogeneity as defined can be measured and inferred within ore-bodies.CITATION: Hellicar, A, Sennersten, C, Lindley, C and Evans, B, 2018. Heterogeneity assessment for grade engineering in complex ore bodies, in Proceedings Complex Orebodies Conference 2018, pp 11–13 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By Z-Y Pi, B Zhang, S Wen

"The paper introduces the structure and work processes of outside auger hollow claw tipped mechanical sampler for coal. Twenty sets of claw tipped sampler performance tests show that: The design of inner hollow cylinder-type (?180 mm) can ensure to take a coal sample with nominal top size of 60 mm. Built-in self-cleaning piston pusher ensures no adherence and blocking of the sample. The operation practices show that the mechanical sampler can operate in order for taking coal sample with up to 16 per cent of total moisture. Claw closing design can avoid sample leaking or spilling during the claw lifting and ensure the integrity of primary increment. Ultrasonic positioning device makes the sampler capture the materials no less than 10 cm from the bottom of the wagons, basically meeting the requirement taking full depth of the sample. The precision and bias test indicates that the moisture and ash have no relative bias under the sampling process; the sampling precision is in accordance with the requirement in IS013909.At present, the spiral mechanical sampler is widely used for coal sampling but there are many limitations during application, for example: It is difficult to capture a large size sample, so the size range of a coal sample taken is limited. There is easy adhering or blocking for high moisture coal, which will result in the mixture of different increments, wear of sampler and the difficulties for cleaning and maintenance of sampler. It is difficult to capture the coal sample at lower than 30 cm from the bottom of the wagons, in order to avoid damage of the vehicle. It is possible for coal sample loss and spilling during the sampler lifting, due to the unsealed sampler.For the outside auger hollow claw tipped mechanical sampler designed for solving the above problems, the opening distance of the claw is the opening size of the sampler and makes the size range of the coal sample to be taken wide. During sampling, the two pieces of claws open and the sampler rotates vertically downward to capture an adequate coal sample after reaching the specific point. Then the two pieces of claws close tight automatically to ensure there is no coal leaking or spilling. The inner pusher of the sampler will prevent from the adherence and blocking of the coal sample effectively.CITATION:Zhang, B, Pi, Z-Y and Wen, S, 2012. Outside auger hollow claw tipped mechanical sampler for coal, in Proceedings Sampling 2012, pp 41-44 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

By V S. Vutukuri, K Shariar

This paper present a modification of selected strength criteria for coal and rocks containing weakness planes. The three strength criteria, namely, Murrell (1965), Bieniawski (1974a, 1983) and Hoek and Brown (1980) have been assessed for coal (containing weakness planes) by using triaxial strength tests. Triaxial test results indicated that the strength of coal specimens depends on the weakness plane inclination with respect to the principal stress direction. However it is shown that with increasing confining pressure, the effect of weakness planes inclination on the strength of coal specimens is reduced. The constant parameters in the three failure criteria for coal are determined for each weakness plane inclination by using the Datafit computer program (nonlinear regression analysis) and the results are compared with other rock types.

Jan 1, 1999