Search Documents

Draft tube circulators are now widely used instead of Pachucas for suspension of slurries in large tall tanks.Precipitators in the alumina industry are an example.Draft tube/tank diameter ratio is critical. Two independent criteria are given for optimum ratio. The hydraulic and energy relationships are defined. These require an impeller of very high specific speed. For a stable and efficient system the impeller should have aerofoil blades with a pitch angle which decreases from hub to tip.The draft tube must be matched to the impeller with inlet baffles above the impeller and flow control vanes below it. Tip recirculation must be suppressed. The tank itself should have a filleted flat bottom.Such a system exhibits the behaviour of axial flow devices with the characteristic undesirable behaviour at low flow.Installed and operating power requirements depend critically on hydraulic design and to a lesser extent on speed reducer efficiency.The problems of re-suspension have been overcome by a patented slot system which also improves behaviour at low flow to permit a more economic design. A number of other practical operating considerations are also discussed.

Jan 1, 1982

By B Mohanty, D Zwaan

Systematic near-field vibration monitoring of stope blasts was carried out in a large, deep underground mine. A total of 31 production blasts were studied in order to investigate the effectiveness of existing blast designs. This involved the vertical retreat mining method, which requires drilling a raise bore or blasting a slot raise (typically 1.22 m in diameter) using large diameter boreholes (165 mm). The diagnostic technique employed multistation near-field monitoring of blasts with high-g (100 g) and high-frequency (>10 kHz) triaxial accelerometers. The amplitude of the vibrations is correlated with the strain energy transmitted from each explosive deck. The results showed that more than 30 per cent of the explosive decks contributed little energy to the rock breakage process in these blasts, and an equal number contributed only inadequately. These findings are indicative of serious blast malfunctions. The problems can be traced to inadequate deck blast design and possibly to drill hole deviation. The various causes for such malfunctions are discussed and remedial measures suggested.CITATION:Mohanty, B and Zwaan, D, 2015. Assessment of underground production blast designs and blasting performance, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 607–616 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

An oxide ore heap (80,000 ton assaying 2 per cent copper) and a sulphide ore heap (300,000 ton assaying 1·7 per cent copper) are being leached in series in a closed circuit system. The ore is friable and weatherseasily giving severe percolation problems. These were eased by applying liquors at 235 gal/min to trenches 2 ft wide and 6 ft deep along the full length of the heaps.Cementation recovery was improved from 20 per cent to over 80 per cent by regular intermittent agitation of the iron using a back hoe unit.Liquor pH is controlled by acid addition, and iron content is controlled by a bleed-off set according to predictions made from a pH-Eh diagram drawn for the liquor components. These controls, together with acyclic wetting and draining procedure, have raised production from 6 ton/week to 10 tdn/week of 80 per cent copper.

Jan 1, 1968

By M J. Dunn

The geotechnical model is the cornerstone of any mining geotechnical design and as such the confidence level and reliability of the geotechnical model is paramount. The geotechnical model confidence level needs to be commensurate with the level of design that is being applied or study that is being undertaken. The geotechnical model is made up of several components and the reliability of the data underlying these components ultimately determines the reliability of the geotechnical model.Data reliability is linked to the quantity of data collected, the spatial distribution of the data collected, quality of the data collection and the interpretation of the data. In a typical project, there is an opportunity to improve data reliability through the scoping, prefeasibility, feasibility and final design and implementation stages.Currently, very little quantitative guidance exists in the literature on assessing the confidence level of geotechnical studies, although there have been attempts by various authors (Haile, 2004; Haines, Swart and Kruger, 2006; Read and Stacey, 2009; Dunn, Basson and Parrott, 2011) to qualitatively describe what level of geotechnical data is required. Recently a number of authors (Read, 2013; Fillion and Hadjigeorgiou, 2013; Thomas, 2013) have outlined methods that could be applied to assess the reliability of some types of geotechnical data that are used in the development of geotechnical models.This paper briefly discusses some of the factors influencing data reliability and the geotechnical model confidence and some of the tools available.CITATION:Dunn, M J, 2014. Geotechnical models and data confidence in mining geotechnical design, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 127–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By S Wainio, P J. Beckett, T Miller

Lichens are a symbiosis of fungi and algae. Air borne elements and gases are absorbed very efficiently over the entire surface of the lichen, because they have no protective structures such as a waxy cuticle or stomata. A survey in 1977 (one year before the Sudbury Regreening program began), indicated that several Cladonia spp had invaded the soil in Sudbury’s open birch woodlands. Pollution sensitive species such as Cladonia rangiferina and C. mitis occurred 20–25 km from the smelters. It was anticipated that the improvements in air quality and reclamation efforts would allow a natural invasion of pollution sensitive species into what once was a lichen desert that surrounded the smelters. The purpose of this project was to study the invasion of terricolous (soil-inhabiting) communities of lichens and mosses on reclaimed land in the Sudbury region 45 years after commencement of the Sudbury Regreening Program.

Aug 2, 2023

By J Planner

As Australia’s coal and iron ore export volumes increase to meet international market growth, port terminals, mining operations and rail transport systems can be the source of increased dust emission. Current and future sustainable expansion must minimise dust emission from bulk handling and transport operations located in close proximity to residential areas. Lower level dust emissions can be controlled by operational measures such as water addition to products, and use of water spray on stockpile surfaces. Recent research has shown that higher levels of dust emission can be more effectively controlled by understanding and treating the dust characteristics of each individual bulk product. Application of this research, progressively being applied at Australia’s coal and iron ore port terminals and rail transport systems, is achieving compliance with health standards and minimising dust nuisance effects to an acceptable level.

Nov 22, 2011

In March 2003, Rio Tinto Coal AustraliaÆs (RTCA) new Hail Creek open cut coal mine commenced operations in the Bowen Basin. Hail Creek is a two-seam strip mining operation utilising two 90 m3 draglines and a fleet of excavators and trucks to remove the overburden. All overburden at Hail Creek is blasted prior to excavation. The mine conducts its own drill and blast operations while engaging Dyno Nobel for the provision of explosives supply and loading truck (bulk explosives vehicle û BEV) services. This arrangement was favoured over outsourcing the entire blasting function to a contractor. Subsequent to a value engineering review, the mine set about developing and implementing a blasting operation that did not rely on the need to store bulk quantities of ammonium nitrate on site. There were advantages identified in doing this, in particular the reduction of capital expenditure required and reduced exposure to a number of recently introduced security requirements. This approach also makes sense operationally. The establishment of reload facilities for the BEV close to the blasting location, where turnaround times are kept to a minimum, increases the productivity of the BEV. For this strategy to be successful the logistics of ammonium nitrate supply into the blasting operations has to be well planned and thoroughly executed. This means a robust planning and forecasting arrangement needs to be established with the supplier and transporters of the ammonium nitrate. To date, 80 million bcm of overburden has been blasted at Hail Creek and each year the quantity of overburden requiring blasting is increasing. The purpose of this paper is to present the findings of a study: evaluating the effectiveness to date of the strategy to conduct blasting operations without ammonium nitrate storage on site, and identifying whether there is a limit to which this strategy can operate after which the introduction of bulk ammonium nitrate storage facilities are necessary.

Jan 1, 2007

By A Larsson, K Niiranen

The Palaeoproterozoic Leveäniemi iron oxide apatite (IOA) deposit of the so-called Kiruna type is currently mined by Luossavaara-Kiirunavaara AB (publ.), commonly known as LKAB. The mineralogy of iron oxides, ie magnetite, hematite, maghemite, and goethite is more complicated compared to the neighbouring and more famous IOA deposits of Kiirunavaara and Malmberget. Furthermore, the mineral chemistry of the iron oxides in the Leveäniemi deposit is also slightly different. Especially, the information about the deportment of titanium and vanadium in iron oxides and distribution in the deposit is essential since they can have an impact in the steelmaking process. For this study 50 samples were selected from exploration drill cores and investigated by optical microscopy, FE-SEM-EDS and EPMA at LKAB and the Geological Survey of Finland. Investigations revealed that magnetite is the predominant iron oxide mineral with secondary hematite being the second most abundant mineral. Primary hematite, maghemite, and goethite seem to be less abundant. It should be noted, however, that this investigation focused on magnetite which currently is the only mineral with economic value. Vanadium occurs as a substitution element in the crystal lattice of iron oxide minerals in the Leveäniemi deposit and not as discrete stochiometric vanadium minerals. In the investigated samples vanadium concentration in magnetite ranges from 0.12 to 0.32 wt per cent V2O3 with higher concentration in the southern part of the deposit. Contrary, titanium does not substitute for iron in the crystal lattice of magnetite or secondary hematite (less than 0.018 wt per cent TiO2). It either occurs as tiny inclusions of titanium oxide minerals or as exsolution lamellae of ilmenite in magnetite. The spatial distribution for titanium in the deposit, however, remains unknown. Furthermore, results of this study indicate that alteration of primary magnetite to secondary hematite has had no significant effect on the trace element chemistry of these minerals in the Leveäniemi deposit.

Nov 8, 2021

By M J. Nugus, J G. McLellan, T G. Blenkinsop

High fluid pressures and deformation have been instrumental in the formation of high-grade gold lodes at the Archaean granite greenstone 12 Moz Sunrise Dam gold deposit in Western Australia. Historically, predicting the location of these lodes has been difficult due to the irregular nature and high-grade nugget characteristics of the deposit. Recent exploration successes and the discovery of the Vogue system have led to an improved knowledge of the deep extents of the mine. This new structural and gold distribution data has enabled a new 3D interpretation of the system and has provided a better insight into the links between deformation, fluid pressure evolution and gold deposition. Here we employ 3D geomechanical and coupled fluid flow modelling to better constrain areas of high strain partitioning, rheological failure and focused fluid flow, which provides a substantially increased predictive capacity for further within-mine exploration. The localisation of deformation in and around the main felsic porphyry and major shallow shear zones provides critical insights into fluid pathways that have contributed to the distribution of fracture networks and ultimately gold deposition during late stage deformation events. Understanding the relationship between deformation events, fluid pressure evolution and the partitioning of strain is paramount in understanding the distribution of gold and for focusing on future target areas.CITATION:McLellan, J G, Blenkinsop, T G and Nugus, M J, 2013. Fluid pressure, geomechanical evolution and predictive targeting of the Sunrise Dam gold deposit, Western Australia, in Proceedings World Gold 2013 , pp 419-426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Drury SA, Williams RD, Nind DC

The Airborne Thematic Mapper is an eleven channel digital scanner which acquires image data in the visible, near infra-red, short wave infra-red and thermal infra-red wave- lengths. A description of the system is presented which includes details of the operating wavelengths and performance parameters of the scanner. Consideration is also given to the aircraft installation requirements. During January 1984 the scanner surveyed the mineral rich areas of Leonora, Laverton and Kalgoorlie in Western Australia. This is a region of intense exploration activity for gold and base metals. Some 30,000 square kilometres were systematically surveyed in a period of ten days. This scanner was flown at 7,000 metres altitude giving a ground pixel size of 17.5 by 17.5 metres. The flight line spacing was 8 kilometres. The overall project took some thirty days from conception to completion. The planning and execution of this operation are described in detail. The resulting magnetic tapes provided 11 channels of digital image data over a 30,000 square kilometre area and a variety of image processing techniques were employed in order to capitalise fully on the results. The imagery provides a powerful tool for the geological mapping of the terrain. The data can also be used to monitor the environmental effects of mining operations.

Jan 1, 1986

A number of cooperative studies have been carried out as preliminary work for drafting a standard for application of granulated slag sand for concrete, and the following conclusions were reached 1 The ten kinds of granulated slag sands pro- duced in Japan satisfy the national standard for fine aggregate in terms of physical and chemical properties. 2 Mortar and concrete tests conducted with granulated slag sand revealed that, although with slight differences in the extent, gran- ulated slag sands used in these tests were applicable'as fine aggregate for concrete, 3 The pumpability test by a concrete pump carried out on concrete with two kinds of now commercially available granulated slag sand demonstrated that the pump pressure feeding is applicable in the same manner as in the case of ordinary concrete. These tests permitted' preparation of a draft standard for application of granulated slag sand, and the results formed the first step toward utilizing this material as a sub- stitute for natural sand.

Jan 1, 1979

By Trueman R

If continuous mining systems are to be successfully applied in metalliferous mines then reliable models will be needed to predict rock cutting machine advance and tool wear rates for effective machine selection before mining commences. Many of the predictive models developed to assess cuttability in situ are over-simplistic. As a result they tend to be both site and/or machine specific. Nevertheless very detailed models have been developed for full face machines which are capable of accurate cuttability predictions in a variety of rock mass conditions and for a variety of machine and tool configurations. However, models to predict productivity and tool consumption for partial face machines are not as well advanced. There is a need to develop reliable models for partial face machines such as Roadheaders, the Robbins Mobile Miner and the HDRK-Wirth CMM, as these types of machine are likely to predominate in a mining environment. The paper outlines the current state-of-the-art for predicting cutting machine performance and the work being carried out within the Centre for Mining Technology and Equipment (CMTE), in collaboration with the Australian mining industry, to advance our capability in this area.

Jan 1, 1995

By Pandey A. K, Srivastava A, Das A

Drilling and blasting constitute important activity in mining operations and account for around 20% of the total excavation cost. The utilization coefficient of energy for explosions of the fragmentation type is hardly 15 to 2035 and an enhancement in this is possible only through optimization of blast design. Designing a 'blast is a complex planning task, which for optimum results calls for matching the energy level of the explosive, rock properties and bench geometry. Optimum blast design needs a comprehensive study and an objective analysis of the intersecting elements. A cost optimised approach is often adopted with due consideration for all the cost sectors viz., drilling, blasting, loading, hauling dumping, and primary crushing, contributing to the overall miring cost. The present study deals with a performance prediction model which predicts the optimum burden for an explosive system in a given rock type to produce a certain desired fragment size. The model is framed on the inputs : shovel size, drill size, unit cost of drilling, bench dimensions, rock density, bond index, unit cost of explosive, maximum work potential. The model has been extended to compute the drilling and blasting costs for an assumed size of the bench to be blasted per round, so as to arrive at the overall cost optimization from a number of explosive systems. A comparative cost calculation with different explosive systems has been presented for a typical iron ore mine in India.

Jan 1, 1990

By Porter I

Rock mass classification systems have emerged as a powerful tool which can be used for assessing ground conditions and determining support requirements in underground mines. They should not be used as a substitute for complete engineering design, but rather as a supplement to observational methods and analytical study. In general, the use of rock mass classification is attractive, but each classification system has various deficiencies. Use of any particular system should be made only with knowledge of that systems limitations. It is desirable to employ a number of systems and design methods which will allow for comparison and lead to a better understanding of the rock mass condition.The Rock Mass Quality system (Q-System), developed by the Norwegian Geotechnical Institute, and the Rock Mass Rating (RMR) System, Bieniawski, were designed primarily for civil engineering structures. Laubscher et al (1978) further developed the RMR-system specifically for rock mechanics engineering in the mining industry. A method of stope design, which introduces a stability factor for the rock mass and compares this with hydraulic radius, was developed by Mathews et al (1981). This paper reviews the above systems by applying them to stability assessment of crown pillars in two Australian metal mines and provides a critical analysis of the various approaches. In particular each system will be analysed to determine its suitability for use in crown pillar design. The most suitable system(s) will form the basis for future development in crown pillar stability analysis.

Jan 1, 1994

By Sobek S, Lotzien RM

Although the conventional procedures for designing agitator flotation plants are well-known and reliable, little experience for designing modem pneumatic flotation plants has been gained up to now. A reliable procedure originating from graphic methods for the design of distillation columns is presented. Examples demonstrate on laboratory and semi-technical scale the application of this extremely practical method for designing a fly ash and a magnesite flotation plant.

Jan 1, 1993

By A Hollweg, K H. Esbensen, M Lischka

Two new splitter designs for intercepting moving streams of matter are presented, the variable cross-stream splitter (vCSS) and the rotary stream splitter (RSS), which are intended for implementation in a fully automated modus. The vCSS facilitates obtaining up to three subsamples with different splitting ratios from automated laboratory flow paths, while the RSS divides the intercepted sample into 16 equal analytical aliquots. The splitters can process a wide range of dry, granular and free-flowing materials (<5 mm). The required weight for each subsample can be set without mechanical adjustments in the case of the vCSS. Typical applications are subsampling/splitting for X-ray fluorescence pelletisation (or fused beads) or splitting for average shift composite sampling or grain size analysis. The vCSS combines the advantages of riffle splitting (three user-defined subsample masses) with miniature bed blending and can accept up to 15 kg in total incoming sample mass. In practice, the automated vCSS can deal with unlimited ingoing mass fluxes, while the RSS is designed to operate at a user-defined fixed subsampling rate (1/16th in the tested version). Both splitters have the potential to be optimised and evaluated according to an application/user-defined total sampling error (TSE) + total analytical error (TAE) threshold. Both splitters were tested under adverse conditions and with compositions involving three components with properties representing typical mass fluxes and components concentrations in industrial and technological systems: phosphate concentrate 89.00 per cent (<500 µm), slag ten per cent (>2 mm) and glass spheres one per cent (750–1000 µm). The slag particles vary widely in particle shape, aspect ratio and surface roughness, while the glass spheres are extremely prone to bouncing and segregation (spillage). This test system is extremely difficult to split and thus constitutes a realistic worst-case scenario. While the vCSS does not comply strictly with Theory of Sampling demands for correctness, both splitters may well be able to deliver fit-for-purpose representative results if/when tested properly. Average relative mass deviations ranged from 1.89 per cent for phosphate concentrate (relative standard deviations of 20-fold repeated splitting) to 4.72 per cent for glass spheres and 13.04 per cent for slag. For the RSS, the average replication experiment splitting variation was 2.89 per cent for phosphate concentrate, 4.82 per cent for glass spheres and 11.1 per cent for slag. Both new automated online splitters would therefore appear to be able to be tuned to fit-for-purpose representivity (defined here as maximum relative reproducibility <5 per cent) for many non-extreme materials; however, it is always imperative to test every new type/class of material empirically. There is a wide commercial potential for important materials and commodities sectors, including food, feed, drugs (pharmaceutical), secondary raw materials, recyclates, agricultural products and seeds.CITATION:Lischka, M, Hollweg, A and Esbensen, K H, 2017. New online/atline splitter designs for laboratory automation – feasibility results, in Proceedings Eighth World Conference on Sampling and Blending , pp 159–166 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

The integration of historic exploration geoscientific data with high precision multi-element and isotope geochemistry can provide explorers fundamental information on mineral potentiality, tectonic setting, source signatures, fluid migration, mineralisation environment and the timing of mineralising events. Such knowledge is crucial for ore modelling and target generation, particularly for concealed ore systems in both brown and greenfields. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By D J. Brake

Most mine ventilation engineers are involved in ventilation planning and design in some capacity. Ventilation modelling software used by a competent experienced ventilation engineer is extremely useful in developing good ventilation designs by allowing assessment of a wide range of potential options. Unfortunately, ventilation modelling undertaken by persons who do not have sufficient experience or knowledge usually results in a façade that covers up a fundamentally unsatisfactory design. Ventilation models are produced for a wide variety of purposes including: fault-finding of a problem area in a mine and options analysis for resolution of such problems; a complete review or optimisation exercise of an entire mine’s ventilation system; or a much longer life-of-mine type of study. Models can be intended as the basis for studies with diverse purposes such as primary shaft or airway sizing, primary fan specification, examining re-entry times after blasting, resolving leakage or recirculation, or investigating the impact of fires or underground climate or cooling requirements. The concepts of ‘materiality’ and ‘fitness for purpose’ are essential to developing or using a ventilation model and serious mistakes have been made in wrongly using a ventilation model for purposes for which it was never intended, often because it is simply the most recent model on the mine site. Mistakes at this level often translate into faulty ventilation strategies and inefficient or ineffective use of scarce capital for ventilation projects. Validating a ventilation model is a time-consuming and expensive process and not every model must (or even should) be fully validated to meet the objectives at that time. This paper discusses the application of quality assurance in ventilation planning with particular respect to the ‘basis of design’ (BOD) as well as the standards for validating a ventilation model. It also provides a recommended way of dealing with non-conformances in measured versus modelled values of critical parameters in the model.CITATION:Brake, D J, 2015. Quality assurance standards for mine ventilation models and ventilation planning, in Proceedings The Australian Mine Ventilation Conference, pp 221–228 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By KeBler H-W, Seeliger A

Vibration analysis for diagnosis of machines is a powerful instrument for condition monitoring. Especially for diagnosis of antifriction bearings various equipment and techniques have been developed and are available. The envelope analysis is the most reliable method for bearing diagnosis. Different bearing failures lead to different patterns of the envelope spectrum. Checking the amplitudes of characteristic bearing frequencies is mostly not sufficient for a reliable diagnosis. Therefore human experts compare the pattern of the spectrum with typical patterns of bearing defects. In this paper a diagnosis system is presented which imitates this action of human experts. Using a neural net the system not only distinguishes typical bearing defects but also detects unbalance, beating of disengaged machine parts and other kinds of machine failures.

Jan 1, 1995

By Longtin Z, Jin C, Zixin C

This paper proposes a new idea of disintegrating mode (division into simpler sub-problems) for complex problems, and based on -it, a study of the structure and the design of a knowledge base and inference engine for layout design of mineral concentrator expert systems. There is also a study of the formalisation method for describing the layout picture, and the work derived therefore found a formalisation method for expressing the knowledge and experience of layout design. There is also a study of the general characteristics of layout design knowledge.

Jan 1, 1993