Search Documents

By Clark IH

Numerical modelling is an effective aid for the planning and design of underground coal mines. With funding from the National Energy Research Development and Demonstration Program, CSIRO Division of Geomechanics has produced a workstation environment which will allow the Australian Coal Mining Industry access to a wide range of numerical design models. The emphasis is on usability and simplicity and the long-term aim is that the techniques should be used routinely at the mine site, so that, in the future, design of a new underground mine will routinely involve modelling of each proposed layout.Each of the five numerical analysis programs, FESOFt, FLAC, MNLAY, FEBLK and UDEC has both strengths and weaknesses. Some analyses with each program demonstrate areas when; observed in situ behaviour in underground coal mines has been successfully modelled, and the results of site monitoring provide a basis for comparison with the predictions of numerical models.

Jan 1, 1991

Key blocks occur on the surface of excavations and on the walls of the ornamental stones and limestone quarries due to the formation of joint planes, fissures, microfaults and quarrying operations. Movements of these key blocks have produced numerous important failures and are responsible for routine overbreak and rock falls accounting for great costs. The thrust of this work is to demonstrate how to delimit zones of poten- tial key blocks (danger zones) in the wall of Bani-Khalid quarry of lime- stone by using the block theory technique (stereographic projection). The final result of this study indicated that, there are three potential key blocks, the most critical one has been determined. To treat the problem, we sug- gest either to provide timely support to prevent the movement of this block, or to analyze it further in hopes that available friction on the faces will hold it safely in place.

Jan 1, 1989

By Mathews K. E, Willstead T. V C

Initial glory holing was followed by sublevel stoping, with a small proportion of total production mined by shrink and cut-and-fill methods.The sublevel stoping method was successfully modified to cater for altering ground conditions encountered at increasing depths. At present, 94 per cent of production comes from sublevel stopes. The evolution of this mining method and current techniques and practices is outlined. A combined shrink and,sublevel benching method was also developed to increase the mining rate of narrow orebodies over the standard stoping lift of 380 ft. Pillar recovery and stope filling operations have been continuously modified to suit the relIuirements of a rapidly developing mine.INTRODUCTIONOre production commenced at Mount Isa Mines in June 1931. Since then production has increased from approximately 2,500 tons of lead ores per mine day to the current 11,000 tons of sulphide ores per mine day comprising 3,100 tons of lead ore and 7,900 tons of copper ore. The early planners selected sublevel stoping with ring drilling for ore breaking as the most efficient and economical for Mount Isa conditions: This method satisfied requirements for:1. a low cost mining method for the comparatively low grade ores,2. a stoping sequence allowing development, stope preparation, breaking and drawing of ore to proceed concurrently,3. a method of extraction in which broken ore in the stopes would be kept to a minimum because of adverse effects of oxidation on mill metallurgy and...

Jan 1, 1961

By J Law, S Jahanshahi, R Holmes

Iron ore is AustraliaÆs largest commodity export and is vitally important to AustraliaÆs current and future prosperity. However, while major expansions are currently in progress to satisfy demand, the industry is also undergoing major transformations. Reserves of traditional high-grade Brockman ores that have underpinned the Australian iron ore industry since its inception are slowly being depleted and alternative ore types such as Marra Mamba bedded iron deposits, Yandi and Pannawonica channel iron deposits and magnetite deposits are now being developed. However, the impurity levels in some of these alternative ores are higher and they require blending and/or upgrading as well as an advanced knowledge of their downstream processing characteristics to facilitate cost-effective utilisation by overseas customers. The research challenge is to use advanced techniques for mineral exploration, ore characterisation, mineral beneficiation, agglomeration and sustainable processing to identify and develop innovative and breakthrough options for locating, unlocking and enhancing the value of AustraliaÆs iron ore resources. Furthermore, to sustain the steel industry and hence secure the demand for iron ore, there is a growing need to enhance the environmental and business performance of the industry through reductions in wastes and emissions. Therefore, cost-effective breakthrough and enabling technologies that massively cut waste generation, CO2 emissions and water consumption are also being developed. These include the use of renewable fuels and reductants, waste heat recovery and conversion of by-product slag into a saleable substitute for Portland cement. A number of examples of recent developments in the above areas are provided in this paper.CITATION:Holmes, R, Jahanshahi, S and Law, J, 2013. Research and innovation for the iron ore to carbon steel value chain, in Proceedings Iron Ore 2013 , pp 3-6 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By M Magee, D Way

The Mount Isa Copper Concentrator was commissioned in 1973. In 1991, two autogenous grinding mills were installed replacing two stages of crushing, one stage of rod milling and one stage of primary ball milling. The cyclone overflow P80 of the secondary ball milling circuit was reduced to 120 microns due to the increased operating power in the AG/SAG mill circuits. A study of the mineralogy of the milled products and the plant flotation recovery indicated that the installed secondary grinding energy was more than what was required for adequate liberation of the chalcopyrite and half of it had potential for more effective use elsewhere. Halving the secondary grinding energy meant only one of the two secondary ball mills would be needed. The predicted saving in operating cost of one less ball mill was more than two million dollars per annum. This paper summarises various plant trials that were conducted in the Copper Concentrator to decommission one of the two secondary ball mills.

Jan 1, 2004

By MacLean L

In 1975 the Commonwealth Government established import parity pricing for all liquid hydrocarbons discovered after the 16th September, 1975. These discoveries were termed "new oil" to differentiate them from existing discoveries and production. Overnight the price of the product being sought trebled, resulting in greatly enhanced economics by increasing the potential returns on existing prospects and by making smaller plays economically viable. After 18 years of drilling, the offshore Gippsland Basin has attained a moderate level of exploration for a basin of its size. Fifty seven prospects have been drilled within the basin but only a few of these were drilled along the southern and northern margins, while the deep water areas along the eastern margin have remained virtually undrilled following the Hapuku-1 oil discovery. The major hydrocarbon accumulations within the basin are trapped beneath the Latrobe Unconformity surface and exploration has largely concentrated on this single play in areas immediately adjacent to the major producing fields.

Jan 1, 1982

By B Walsh, M Cattani, S Verpaele

With the increasing sophistication of real-time sampling devices for occupational hygiene exposure assessment, research to objectively assess their performance is a priority. Using real-time monitoring equipment has several advantages over established gravimetric sampling methods, particularly their immediate results, lower overall long-term costs and no laboratory analysis costs, which are appealing to the mining industry due to the ongoing occupational hygiene monitoring programs required by the various regulatory agencies.

Apr 16, 2024

The design of a mine should aim to optimise the market value by maximising revenues whilst minimising costs. In open pit mining, the nature of the extraction technique translates this objective into the maximum recovery of reserves while minimising waste extraction subject to technical, economical and safety constraints. Since the introduction by Lerchs and Grossman, in 1965, of a model that is now considered a classic in the area, open pit design has reached a level of maturity and acceptance by industry. These models are being used on a regular basis by designers and planners.This paper proposes a new alternative model for open pit design. It is based on genetic algorithms (GA) and exploits a reduction of the number of decision variables of the more traditional techniques. The novel approach provides more flexibility than traditional models; it can also be extended to consider planning problems that traditional open pit design models are not capable of handling. The algorithm has been designed for two dimensional problems and tested in a simple instance. The results obtained in this simple test are encouraging and are a good supporting argument for the development of a GA model capable of handling three-dimensional (3D) instances. The model presented in this paper is just a first step towards a full GA to solve the pit design problem and it is believed that novel tools like the one presented herein could become great allies in tackling challenging problems in open pit design, an illustration of such a challenging problem is presented and discussed.

Dec 6, 2010

By I M. Platten

Narrow reef gold deposits are generally less than 4 m in width and relatively complex geological phenomena. They often display variable geometry, attitude, continuity and internal architecture. Economic grades are mostly restricted to specific structural domain(s) and localised within discrete ore shoots that have a nuggety internal grade distribution. On account of the often extended history of geological events, the specific factors localising gold-rich domains are likely to be unique to a particular mine or even reef. These features lead to a high resource risk and require careful management during both evaluation and mining. The gross form, location and global continuity of gold reefs can generally be determined from surface diamond drilling leading to the definition of Inferred Mineral Resources. It is likely that for the definition of Indicated and Measured Mineral Resources underground development and/or close- spaced diamond drilling will be required. Understanding geometry and continuity permits the resource to be more effectively managed, lowering risk/uncertainty. This in turn will allow for well-informed financial and operational decisions. Most importantly, project expectations and milestones can be set at achievable levels.

Jan 1, 2008

By M Salu, G J. Kay

"As underground mines increasingly face the challenge of maximising production without losingfocus on safety excellence, the ability to predict the eff ectiveness of mine seals and stoppings andthe identifi cation of defects plays an increasingly important role in mine ventilation management.While technologies for sample testing installed seals provides signifi cant assurance, the difficulty of conducting tests in operational environments, combined with the production impact of destructive testing procedures, has led to the development of a new method for non-destructively testing ventilation control devices (VCDs). This paper addresses the challenges of in situ testing and reviews the approaches previously employed to verify the quality of VCD installations. It then describes a new testing methodology jointly developed by Whitfield Minerals PTY Ltd and Parsons Brinckerhoff (PB) and the range of tests that have been carried out in the laboratory, above ground, at trial underground sites and in active coal mine operations. Although this is a new approach to testing underground VCDs, the method employs recognised testing equipment in a new application. The aim of the new non-destructive technology is to not only verify the thicknessand therefore overpressure rating compliance, of new VCDs, but to allow mine operations t oidentify and locate defects in installed VCDs without causing damage to the material structure.Currently it is difficult, time-consuming and costly to carry out physical sampling and testing ofevery VCD. Therefore, a reliable and accurate means of non-destructively testing concrete andplaster seals in situ will provide substantial operational and safety benefi ts to the underground coal mining industry."

Jun 1, 2012

By R Grogan

The Ungay-Malabago polymetallic deposit, currently owned by Lafayette Mining, is located on the eastern end of the island of Rapu-Rapu which lies east of the city of Legazpi in the Philippines. The island is sparsely populated and has largely been deforested by extensive logging some 30-40 years ago.The deposit is situated on a plateau some 200 m asl and lies about one kilometre inland from the coast. The site topography is difficult with minimal flat areas for plant facilities. The region around Legazpi is subject to volcanic activity and though the island is not affected it is in a seismic zone. There is no other mining or other industrial activity on the island, the local inhabitants being engaged in subsistence farming and fishing. These activities place a high level of responsibility on the mine operator with regard to the environment and the provision of employment and training to the local inhabitants. Although no previous mining was carried out at Ungay, shallow pit mining for high-grade direct smeltable copper ore has occurred during the mid-1900s in an area, known as Hixbar, some 2 km west of the deposit This area is currently being explored by Lafayette.

Jan 1, 2002

By G Noonan, S Thomas, M Limbert

Stuck drill rods (often referred to as bogged rods) in production ‘upholes’ are a common problem in the underground mining industry. Bogged and broken off drill rods have the potential to fall out of the hole without warning, posing a serious hazard to personnel and equipment below.Current industry practice to alleviate this hazard can be to either grout the hole in order to lock the drill rods in place, or to ‘plate over’ the hole with a rock bolt. Each of these operations seriously delays mine production as both require demobilisation of the production drill and mobilisation of alternative personnel and equipment to address the hazard. Both methods have been assessed for safety and efficiency and were found to be expensive, time consuming and in the case of plating over, ineffective.To address the safety and efficiency short-comings of the traditional practices, the long hole plug (LHP) has been developed to safely secure the lost rods in the hole. The LHP when struck by falling drill rods behaves similar to an expansion shell anchor transferring the axial forces from the falling drill rods horizontally into the rock mass. It is installed using standard production drills allowing work to safely continue with little interruption.Extensive testing has been carried out on the LHP in the laboratory and underground at the Rosebery mine on the west coast of Tasmania, Australia. Testing has included static pull testing, full scale drop testing and underground trials.The outcome of this work has proven the LHPs ability to add safety, volume and cost benefits to the Rosebery underground operation and it is currently in use at that site. It enables proven elimination of a common workplace hazard immediately, thus eliminating delay on the mine’s production cycle.CITATION:Thomas, S, Noonan, G and Limbert, M, 2017. Long hole plug – addressing the hazard of bogged rods in ‘upholes’, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 305–310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By G Eastwood, C Joyce, P Ryan, G M. Johnston

Over the years, predictive techniques for Acid Mine Drainage (AMD) and the natural processes affecting acid generation have received considerable attention. Less emphasis has been placed on the sampling strategy and the integration of testwork results with the geological data base. The sampling strategy employed and the development of a geological model to determine the spatial distribution and volume of acid producing material are often crucial for developing cost-effective containment and mitigation measures. The geological model provides a link between the occurrence, timing, destination and placement of mined waste rock. Careful and accurate interrogation of a comprehensive geological database provides this linkage. The AMD testwork program at Cadia in NSW has been designed to identify the temporal selective handling requirements that will be required during operation. Sampling involved collection of representative combinations of all waste rock types identified within an extensive geological database. These samples were subjected to static, kinetic and accelerated weathering predictive tests. Preliminary results have been used to construct a waste block model for the deposit that identifies the quantity and distribution of acid producing material. Integration of the block model with the mine scheduling determines when the material will be mined.

Jan 1, 1996

By King D

Recent field experiments in the United Kingdom (Buchanan, 1979) have shown that the in-seam technique is capable of detecting a 1m fault in a 3m seam, at a range of 280m and with a resolution of ¦40m. Comparable tests in Australian collieries are proceeding. Although the practicality of an implementation of the technique on a routine basis remains to be demonstrated, the potential of the technique for the prediction of outbursts clearly warrants detailed examination. This potential will,depend, inter alia, on the level and scale of variations in elastic (and anelastic) properties of bodies of coal undergoing stresses associated with mining. Available data, mainly from studies of the seismic properties of gas saturated reservoir rocks, confirm the intuitive view that stress increases give rise to increases in seismic wave velocity and decreases in wave attenuation, markedly at low stresses (as pore spaces close with little resistance) but less so as stress increases. Such increases are of the same order as aniso- tropic effects, but should provide impedance contrast sufficient for detection by in-seam seismic methods. At higher stresses, cracks form within the rock mass. Results from research on earthquake prediction provide some clues to the behaviour of sedimentary rocks sub- jected to large stresses. In particular, the

Jan 1, 1980

By L C. Thompson

Biomineralisation is the process by which microorganisms mediate and catalyse inorganic reactions so as to form new mineral assemblages. The goal of biomineralisation as a remediation tool is to control microbial processes and their environment so as to sequester and immobilise specific toxic metals within exceptionally strong bonds of neo-formed mineral assemblages. In this way, the bound metals are no longer mobile within a geological time-scale. Applied biomineralisation uses microorganisms, which are isolated from a metal waste environment and are selected for their ability to rapidly catalyse neo-mineral development from dissolved or leachable metals. A typical waste environment will contain microbes that contribute to the mobilisation of metal contaminants as well as microbes that possess the potential for remineralising available metals. Selection and augmenting the correct combination of bacteria and eliminating the competing mineral degrading reactions are the key to applying biomineralisation as an in situ remediation process. Applied biomineralisation harnesses the microbesÆ ability to stabilise toxic soluble metals into non-mobile mineralassemblages. This paper will discuss and demonstrate the biomineralisation process through several case studies including the Summitville mine site in Colorado, the McCoy-Cove mine in Nevada, the Argonaut mine in California, and an historic lead site in Crooksville, Ohio.

Jan 1, 2004

By C Nucifora, M Landers, J Jones, G Maddocks, K Mandaran, A Forbes, W Wilson, S Newman

Glencore’s Mount Isa Mines Limited (MIM) operates the Mount Isa open cut and underground copper (Cu) and zinc-lead (Zn/Pb) mines near Mount Isa in Queensland, Australia. Tailings from processed Cu and Zn-Pb ore is contained in a 1,315 ha shallow (< 35 m deep) multi-cell valley fill tailings storage facility (TSF). Static geochemical testing conducted by MIM over the life of mine (LoM) verifies that the Cu, and Zn-Pb tailings has a wide range in sulfide content and diverse mineralogy with significant acid neutralising capacity (ANC) in some samples. The tailings are predominantly classified as potentially acid forming (PAF) using static analytical methods. Kinetic leach testing using free draining columns and humidity cell tests simulating tailings placed on the surface of the TSF suggest that the tailings samples are likely to remain non-acid forming (NAF) for 10 to 40 years under aerial exposure, and much longer than this under saturated conditions within the TSF. During this period of weathering, as ANC is depleted, the neutral pH drainage may contain elevated concentrations of some elements including sulfate, manganese and zinc. Only when the ANC is depleted would the tailings then begin to produce acid drainage. CITATION:Mandaran, K, Jones, J, Nucifora, C, Maddocks, G, Landers, M, Forbes, A, Wilson, W and Newman, S, 2018. Mount Isa Mines Rehabilitation Materials Sampling and Analysis program for closure planning, in Proceedings Life-of-Mine 2018, pp 138–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By M J. Kongas, K M. Saloheimo

This paper presents the art of on-stream particle size and elemental analysis used at iron ore concentrators, followed by the results and experiences from several sites.Online particle size analysis is rather common at medium- to large-sized concentrators. Online X-ray fluorescence (XRF) elemental analysis, however, is only used in some iron ore concentrators, while it is a routine practice in base metal concentrator plants. Online XRF analysis is applicable for process monitoring and control down to four to five per cent silica by measuring Fe assays accurately. With lower silica content, direct measurement of silica and other light elements is required. Some light element analysers that are based on the prompt gamma neutron activation analysis (PGNAA) method have been developed, but they have not performed up to expectations with slurry analysis. Other methods have been tried though these have not been used beyond prototype installations. Operating online light element slurry analyser installations are not common in iron ore applications.There is an economic incentive to mine lower and variable grade iron ore resources, which require concentration and removal of several impurities to produce high-quality concentrates for pellet production. Monitoring such operations by on-stream analysis has significant economic benefits, and there is a need to develop a dependable slurry online analyser for Si, Al, Mg and other light elements. The latest developments in slurry on-stream light element analysis are described.CITATION:Kongas, M J and Saloheimo, K M, 2013. Online slurry analysis for process control and monitoring at iron ore concentrators, in Proceedings Iron Ore 2013 , pp 303-308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

This paper discusses the prediction of subsidence over partial extraction systems in thick coal seams. A model based on empirical techniques using influence functions is developed to calculate the surface ground settlements above extraction panels. Independent of the influence function, two field parameters, the subsidence factor and the angle of draw (limit angle) are required to define the model. Both these parameters are best observed from critical or super critical subsidence areas. However in thick seams, extraction widths are typically sub critical and therefore it was necessary to refine an estimation process for sub critical conditions. Partial extraction systems in NZ are characterised by variability with respect to extraction thickness and depth. As extraction proceeds along a panel, conditions deteriorate once the critical span width is exceeded and therefore percentage extraction decreases. A further variable was introduced to the modelling which allows for varying extraction sequences. Two comparisons with field observations, one over a partial extraction panel, the other over abandoned workings, showed the method gave good agreement to measured subsidence values.

Jan 1, 2002

By Crellin D, Reed SM

The paper presents details of borehole instrumentation schemes for the purposes of monitoring rock and fill deformations associated with groundwater in underground and surface coal mines. The instruments are described which measure rock mass displacements, permeability changes and alterations to hydrology. Methods of installation are detailed and the applicability of instruments discussed. Reduction and interpretation of results are detailed.

Jan 1, 1988

The Application of Roasting Pretreatment for Antimonial Refractory Gold and Silver Ores

Sep 13, 2010