Search Documents

By S Logan, J Pu, J Milsom, G McDonald

Management of environmental issues is an integral part of the mine decommissioning process. In Queensland, miners must comply with environmental aspects of the Mineral Resources Act and Contaminated Land legislation. Successful decommissioning involves the integration of a final Plan of Operations, decommissioning report addressing the mineÆs commitments included in its Environmental Management Overview Strategy (EMOS), and Site Contamination Report for relinquishment of leases under the Contaminated Land Act (1991). Niugini MiningÆs Red Dome Mine is proceeding through the decommissioning process. This paper discusses the important environmental management issues including sampling programs, management of culturally significant areas, assessment of background concentrations of target analytes, the use of historical reviews and risk assessment techniques, the timing of works, and the remediation/management of large areas of impacted land. The importance of a clear communications plan between key stakeholders is also discussed.

Jan 1, 1998

By K Heiskanen, R A. Grau

Gas velocity (Jg) measurements conducted close to the froth-pulp interface over the cross-section of a flotation cell reveal how efficiently the incoming air is being dispersed throughout the volume of the cell. Furthermore, measurements of Jg at deepest locations in the cell provide valuable information about air recirculation and dispersion conditions in the bulk volume of the cell. Gas velocity in flotation cells has predominantly been measured by a transient capture of gas in a graduated probe. In this project, a new sensor for measuring gas velocity in an on-line manner was developed. A probe is partially immersed in the flotation machine, below the froth-liquid interface. The probe is used to collect the rising air bubbles from the liquid phase. The liquid-froth interface is shifted into the probe under vacuum. A controlled vacuum is kept inside the probe. As air bubbles burst inside the probe, the excess of air is continuously removed from the probe via suction. The removed air is measured using a mass flow meter. The fully automated sensor allows us to continuously measure Jg at different location in a flotation machine. An experimental programme was carried out in a 10 cm diameter laboratory flotation column to determine the accuracy and repeatability of the automated sensor. The new sensor was used for evaluating gas dispersion conditions in a 215 litre transparent laboratory scale flotation cell. Gas velocity distributions along the radial and axial directions of the cell were measured over a wide range of operating conditions. The operating conditions in the cell were modified by altering impeller speed and air flow rate. Two different rotor-stator mechanisms were utilised to disperse the air in the cell, the MultiMix and the FreeFlow mechanism. In this paper, a description of the gas velocity sensor is given, and the results of the experimental work are discussed in detail.

Jan 1, 2005

By J Williams

The recent drought has highlighted the finite nature of AustraliaÆs divertible water resources. According to AustraliaÆs recently completed National Land and Water Resources Audit, development of water resources in southern Australia has reached or exceeded sustainable extraction limits. Similarly, 161 out of 538 groundwater management units are either totally allocated or already over allocated. Whilst mining only uses about three per cent of diverted water resources, water scarcity may be a major factor that determines whether potential mines can be developed in the future. Furthermore, the development of extraction and processing facilities that limit water use and maximise the re-use the waste water streams will be even more fundamental features of the mining industry in the 21st century than they are at present. There are encouraging examples where innovative water re-use technologies are significantly reducing the water used per unit of mined product. Whilst mining in the areas of Australia draining to the tropical seas may be less constrained by a current lack of water (60 per cent of divertible water resources drain into the Timor Sea, Gulf of Carpentaria and north east Coral Sea), it is highly probable that there will be increasing demand for these waters from the irrigation industry, whilst pressure will also be applied to ensure that environmental flows that benefit the coastal fishing and prawn industries are maintained. In the Great Artesian Basin, current research is demonstrating that the groundwaters are being recharged at rates considerably lower than current extraction. Whilst some other groundwater basins in arid and semi-arid Australia have currently untapped resources, these water are often relatively saline and/or may be intimately linked with key ecosystems in discharge areas. This paper presents an overview of the current state of our water resources and examines some of the key water use issues including allocation, use and reuse, environmental flows and competing demands on the resource that will ensure that water issues remain high on the policy agenda for mining, irrigation and other water users.

Jan 1, 2003

The application of new and currently practised mining techniques in new areas and at greater depths necessitates considerable and immediate research effort. This effort is aimed at identifying the factors which make a particular method suitable and economically viable in a given geological, structural and operational environment. These factors, together with greatly enhanced knowledge of a deposit at the exploration and planning stage, allow selection of the most appropriate and efficient mining method in a new area such that coal resource recovery is maximised in a cost effective manner. Current research and future requirements for research into mining methods and associated equipment and mine services are reviewed.

Jan 1, 1981

In a state-of-the-an review of predictive methods for longwall support load calculation, special respect is paid to those techniques which enable actual roof conditions and local lithology of strata to be involved. Principal systems of roof examination include the borehole perforation test and seismic velocity measurements. Roof strata stability is related to caveability classifications and roof inclination due to subsidence. The critical analysis of both load resistance prediction methods and roof stability classifications shows that each has its own value of reliability level. The present research opportunities analysed underline the significance of developing fully reliable prediction techniques as needed by the coal industry.

Jan 1, 1991

Authors have been conducting research on autonomous loading operation by wheel loader. Autonomous loading cycles has been demonstrated with real size experimental model. In V shape loading operation, travelling between scooping point and dumping point is dominant factor for cycle time of the operation. The positions of scooping point and dumping point changes with advancing the operation. In the developed system, path planning is performed at the beginning of every cycle. The path is formed by combination of curve and straight path elements. During travelling on the planned path, path following control is applied on the loader to keep position error in narrow range. Positioning of the loader is based on dead reckoning with correction by global positioning system (GPS) data. In a process of path following control, control value for steering angle is determined based on position error in lateral direction. Proposed method of path planning and position control is installed and tested in the real size experimental model. The detail and results will be described in the paper.

Dec 6, 2010

The Institute of Geological and Nuclear Sciences (GNS) is commencing a project to develop a National Minerals Information System (NMIS) for New Zealand . Initially, the NMIS project will focus on providing public access via a web site to existing minerals related databases maintained by GNS and some other organisations. Core components are geological maps, GERM (Geological Resource Map), REGCHEM (Regional Exploration Geochemistry), PETLAB (rock catalogue), GEOCHRON (radiometric ages), mineral deposit models, mineral deposit profiles and 3D mineral deposit GIS databases. In addition to developing the web site, the project will include upgrades of some of the databases and the production of derivative products such as mineral resource and prospectivity assessments, and mineral inventories.

Jan 1, 2004

By Wood W, Bell A

Brown coal production in Victoria's Latrobe Valley Region (Figure 1) continues to rise and currently stands at around 50 Mt per annum. With the exception of around 2 Mt used to produce some 700 Kt of brown coal briquettes, this coal is mined by the State Electricity Commission to fuel large thermal power stations with a total installed capacity of just over 5 000 Megawatts. The moisture content of the coal as mined typically exceeds 60 per cent, making Latrobe Valley coal a markedly low rank fuel. The lack of heating value is, however, compensated for through power station design and by the fact that ash yield is very low, usually within the range of one per cent to four per cent on a dry basis. This means that compared with most other coals, the burning of Latrobe Valley brown coal produces relatively small quantities of waste products and discharges a minimal level of pollutants into the atmosphere. Even so, the inherent quality of Latrobe Valley coal does vary significantly from one area to another (Gloe, 1991; Barton et al, 1992) both on a local and a regional scale. Such variations need to be recognised and understood in order to not only realise efficiency gains in existing power stations but to properly assess resource potential for future utilisation and the application of new technologies. The principal aim of this paper is not to describe coal quality variation in detail or to speculate on the nature of and reasons for such variation. Rather, it is to simply underscore that significant differences do occur and that this is clearly a factor which needs to be considered in any evaluation of Latrobe Valley brown coal as a resource for the future.

Jan 1, 1992

Several years and millions of dollars later, the mining and extractive industries have now started to receive and implement industry based standards aimed at achieving better performance and output from the employee. IFAP in conjunction with the mining and quarrying industry has developed a range of training courses aimed at achieving the benefits that can be gleaned from application of these standards. The establishment of a career path and appropriate training packages for personnel involved in the handling and use of explosives provides industry with a training system that previously did not exist. The opportunity to receive quality training based on industry standards and aimed at achieving industry goals will now enable the industry to optimise itÆs explosives applications.

Jan 1, 1999

By Sullivan T. D, Lohe E. M

Geological structure is one of the main controls on ground conditions within mining. It has a significant impact on the mining conditions and productivity of coal mines within the Sydney - Bowen Basin. The three main types of faults common to this region, normal, reverse and strike-slip systems, each present distinct challenges to mining. These systems effect a wide range of geotechnical and mining conditions within the mines. These include coal quality, strata stability, goat and caving behaviour, productivity and maintenance schedules of mining equipment, mine design and mine-site stress fields. A better understanding of the regional, local and mine-scale structural setting, timing relationships of structural events and the mechanisms of fault formation will greatly aid industry's push for greater productivity and competitiveness.

Jan 1, 1991

By D M. Hunter, S M. Iveson, K P. Galvin

For low density materials such as coal, density-based fractionation of particles via the sink-float method is relatively simple due to the availability of liquids of suitable density; however, for high density minerals, suitable heavy liquids are less available and those that are available are expensive and pose significant hazards. At best, sink-float separation can be performed up to densities of 4400 kg/m3 with the use of Clerici’s solution at elevated temperatures. Hence the direct measurement of grade-recovery and density-partition curves is problematic. Therefore, in most cases, beneficiation plants must rely on methods such as QEMSCAN, density tracer particles or very limited information to guide them in the design and optimisation of their plants.This paper describes a density-fractionation method utilising laminar flow through a system of parallel inclined channels to generate a series of overflow fractions at different flow velocities. Here the particles are subject to precise hydrodynamic forces with minimal dispersion or mixing. The size distribution of each overflow fraction at a given flow velocity is obtained using a laser particle size analyser, and combined with a laminar flow model to deduce the corresponding density distribution. The paper describes the application of the method to measure the separation achieved using a REFLUX Classifier to obtain the corresponding feed, product and reject ‘washability curves’, and in turn the full partition surface. Approaches used to corroborate the findings are discussed.CITATION:Hunter, D M, Iveson, S M and Galvin, K P, 2017. A batch elutriation technique for the density-based fractionation of iron ore, in Proceedings Iron Ore 2017, pp 195–104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

It is no longer possible to establish a quarry on the most convenient hill then abandon the site, leaving a scar if the stone or sand in the deposit is found to be unsatisfactory. Before approval is given to operate a new quarry, the relevant authorities require a detailed plan of operations from commencement to final rehabilitation. To prepare this plan, a thorough know- ledge of the quality and size of the deposit is required. To obtain this information, the industry must use the most modern techniques available. Many examples can be given showing problems which have affected the smooth operation of a quarry for many years because the initial exploration was poorly carried out. The factors which must-be considered when exploring a deposit are detailed in this Paper.

Jan 1, 1979

It cannot be said that accurate and reliable ore reserve estimation is the fundamental of any mining operation success. Estimation techniques which are used to estimate the grade distribution of an orebody together with the assessment of uncertainty and risk have a vital influence on the success of any optimisation algorithm. Traditional estimation techniques such as kriging or inverse distance weighting are frequently used for assigning grade values to blocks. Various attempts have been made in order to compare geostatistical estimated methods for ore reserve estimation. This paper aims to evaluate the sensitivity of different estimation methods over changing the block dimension. For this reason, several block models with different dimensions were derived in Chador Malu iron ore mine which is located in 180 km northeast of Yazd in the centre of Iran. Each block model was estimated by different estimation methods such as nearest neighbours (NN), inverse distance (ID) and ordinary kriging (OK). The results of each estimation methods were compared against a control block file created by using the assay results of all blastholes drilled in the ore over four benches of the pit. The results signify that by estimating the large block size, no significant improvement occurred due to the employment of different estimation techniques. Furthermore, the grades estimated based on ID method is more reliable, but OK methods estimated more accurate tonnage.

Dec 6, 2010

By H Han, W Wang, E Zhou, D Duan

"In this study, physical, chemical and microscopic characteristics of high phosphorus oolitic hematite were studied firstly. Based on which, the new methods of high phosphorus hematite used in the æsolid state reduction by rotary hearth furnace - magnetic separationÆ and iron nugget by rotary hearth furnace direct reduction processes were discussed. The results showed that high temperature, low basicity and high carbon content is conducive for the apatite in iron ore to reduce into molten iron, but not conducive to the removal of phosphorus. Through optimisation of process parameters, dephosphorisation rate of high phosphorus hematite is more than 60 per cent by æsolid state reduction roasting-magnetic separationÆ process while that is up to 80 per cent by iron nugget process. This study can provide theoretical and technical basis on economical and rational use of high phosphorus oolitic hematite.CITATION:Han, H, Duan, D, Zhou, E and Wang, W, 2013. New methods for high phosphorus oolitic hematite dephosphorisation by direct reduction process, in Proceedings Iron Ore 2013, pp 391-396 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

Upgrading of a Flow Sheet Selection PC Algorithm for Refractory Concentrates Treatment

Sep 13, 2010

By P Andersson, P Marklund

Evaluation of different techniques for bottom fill stabilisation showed that frozen fill was the most economical method. In order to test the method a full-scale field test was performed in the Rehnstr÷m mine. The test was instrumented with temperature gauges and extensometers. Before the field test, frozen fill was tested at the laboratory. The mechanical properties of the frozen fill were determined by uniaxial compression and creep tests. A deformation model for the frozen fill was set up. Calculation procedure for design of spacing between the freezing tubes, time for freezing and calculation of the necessary capacity of the refrigeration plant was developed. These procedures were calibrated against the field test. The results of these investigations allow the following conclusions: From a mechanical point of view, frozen fill has excellent properties as a structural member and it also has excellent properties to support itself and the fill above. Methods for the thermal and mechanical design of freeze stabilisation have been developed and found adequate. The need to place the freezing tubes several years in advance of the future sill pillar mining, requires careful long-term planning and accurate documentation.

Jan 1, 1998

By J Butler, N Patel, S Narendranathan, S Rastogi

The Yallourn Mine (YM) commenced mining of brown coal in the 1920s under operation by the State Electricity Commission of Victoria (SECV), prior to it becoming privatised in 1996. The present owners of the YM, Energy Australia Yallourn (EAY), acquired the site in 2000 and intend to continue operations until scheduled closure in 2028. Brown coal extracted from the YM is fed into the Yallourn Power Station which supplies approximately 22 per cent of Victoria’s electricity. Water within the YM is collected and stored in the Township Field Fire Service Pond. Water levels within the Fire Service Pond (FSP) may fluctuate considerably depending on the requirement for storage at the site. With due consideration to the stability performance of mine batters adjoining the FSP, the authors performed slope stability assessments to evaluate the risk and consequence of batter instability during the potential pond filling as it approaches the ‘critical pool’. The critical pond is defined as the level at which the driving forces (destabilising forces) are at their greatest and the resisting forces (lake forces, friction) are at their lowest. This assessment was undertaken using the Mine Geotechnical Risk Index (MGRI) approach.

Aug 2, 2023

By Todd S, Lam K, Hewitt A

A series of field experiments investigated the perfonnance of fine mesh curtain screens which were used to suppress coal dust in a transport roadway of a New South Wales colliery. Four types of screens were tested under dry and wet conditions. The screen materials consisted of flyscreen and garden "shadecloth" with single and double membranes of both materials. Personal dust samplers coupled to dust cyclones and filtration cassettes were used to collect the respirable and total components of dusts respectively. The procedure used for locating the samplers upstream and downstream of the screen was based on the roadway air velocity profiles. The number and configuration of the water sprays impinging onto these screens had significant influence on the results. The study showed that wet double layered flyscreen is the most effective of the four configurations tested.

Jan 1, 1991

By Jia X

Three-dimensional microscopic modelling techniques involving specific calculations based on direct computation of the Brownian, van der Waals, Born, electrical double layer repulsion, bulk, hydrodynamic and external forces (gravity, magnetic etc) acting on and between each particle in a mineral dispersion are now feasible using advanced computer processor architectures. This contribution surveys the hardware requirements, the advantages and limitations of the approach for enabling prediction of dispersion behaviour a priori. The notion of developing a generic particle simulator, akin to the use of molecular modelling in the area of drug design, based on inputting process-relevant data (solution chemistry, mineral solids properties, hydrodynamics etc) is discussed. The methodology is illustrated with application examples involving: predictions of coagulation of mineral fines; shape and size of magnetically-flocculated hematite; and the kinetics of fouling of membrane surfaces and walls.

Jan 1, 1993

By Cox A

A key concern both in public perceptions of the environmental performance of the mining industry and in the development of policy relating to mining activities is the state in which the areas may be left at the completion of mining operations. There is, in effect, concern that the transient economic benefits of mining are enjoyed by the few, while the 'scars' may remain for all. While the techniques of mine rehabilitation have improved rapidly in recent years, an important set of economic issues has generally been neglected.In this paper, the economic and policy aspects of mine rehabilitation are examined. The key issue addressed is how to determine when expenditure on rehabilitation should stop. The answer to such a question requires consideration of the full range of social, as well as private, costs and benefits of rehabilitation at a particular site. Clearly these costs and benefits will vary between sites. From both an economic and policy perspective it is important to establish whether the additional gain from more rehabilitation would exceed the additional cost.It is concluded in the paper that the technical feasibility alone does not justify a paeticular level of rehabilitation activity and expenditure. While more rehabilitation at a particular site may be technically feasible, the additional expenditure incurred in undertaking that rehabilitation may result in little extra benefit. This conclusion has important implications for government policy, particularly with respect to establishing the goals for rehabilitation, criteria for successful rehabilitation and enforcement of rehabilitation objectives.

Jan 1, 1992