Search Documents

By T Ireland

The Project Hobson tunnel excavation was the first use in New Zealand of an earth pressure balance (EPB) tunnel boring machine (TBM). The tunnelling on the project was very successful and break-through was achieved three weeks ahead of program, demonstrating that tunnelling can be undertaken in Auckland with a high degree of cost certainty.Project Hobson involved the replacement of an existing 90 year old above ground sewer that crosses Hobson Bay in Auckland, New Zealand, and which had reached the end of its economic life, with a 3 km long, 3.7 m internal diameter segmentally lined bored tunnel. The NZD$ 118 M project has provided several environmental benefi ts to the Owner, Watercare Services Ltd and the local community:· provide capacity to meet projected growth in the region,· virtually eliminate wastewater overflows into Hobson Bay and the Waitemata Harbour, and· remove an obtrusive visual feature and open up the bay for recreational purposes.Auckland’s bedrock is a weak sandstone/siltstone (East Coast Bays Formation), subject to infilled paleovalleys. The geology in the region has been significantly influenced by volcanic activity; 49 volcanoes are present within 20 km of the city centre.The paper describes the design and construction challenges for the projects, including TBM performance, ‘sticky spoil’ management, and risks associated with basalt lava flows and two paleovalleys. The paper also highlights the reasons for the success of the project, including a rigorous approach to risk management during design, and effective planning during construction. Other useful data such as the effect on the watertable caused by closed face tunnelling, and ‘faceloss’ estimates derived from settlement arrays are included in the paper.Project Hobson also saw the successful implementation of a Geotechnical Baseline Report – one of the first uses of this type of document in Australasia.

Mar 8, 2011

By P Craig, A Crosky, P C. Hagan, E Elias, B Hebblewhite, S Saydam, D Vandermaat

"Premature failure of rock bolts has been recorded at twelve underground coalmines over the past 15 years in Australia. Over the last four years, UNSW Australia has been conducting an Australian Research Council (ARC) and Industry funded linkage research project into premature failure of rock bolts. The extent of the problem was investigated by underground surveys of mines with known prematurely failed bolts using visual mapping, non-destructive load and ultrasound testing. A major component of this project was to define the environmental factors responsible for corrosion of rock bolts. The environment to which a rock bolt is exposed will include groundwater chemistry, the mineralogy of the strata, atmosphere within the drill hole and even microbial activity. This paper focuses on the groundwater survey and analysis findings to date along with in-hole bolt corrosion coupons installed into field sites. Corrosivity classification systems exist for general corrosion but do not apply to the rock bolt stress corrosion cracking (SCC) problem found in Australian underground coal. The method of in situ investigations is leading towards the building of a corrosivity classification model to assist mines in prediction of premature rock bolt failure. An ‘in-hole bolt corrosion coupon’ development by the project may have multiple benefits of: helping quantify any corrosivity classification system providing an in situ ground support corrosion monitoring tool for testing possible corrosion protection solutions.CITATION:Craig, P, Saydam, S, Hagan, P C, Hebblewhite, B, Vandermaat, D, Crosky, A and Elias, E, 2014. An investigation of the corrosive impact of groundwater on rock bolts in underground coalmines, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference, pp 277–286 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 5, 2014

By C Simpson

In 2011 the forecasted world demand for iron ore continues to grow, and during this time Australia is looked upon as a reliable supplier of high quality ore. The expansion of the current Australian mines is unlikely to meet the forecast demand. New mines are therefore being actively explored for and when discovered, are quickly being developed into mines in order to meet the world’s hunger for steel.The Solomon Project area is a large new iron ore discovery, located in the central Hamersley Ranges of the Pilbara province in Western Australia. The first Fortescue exploration drill holes commenced on the project in 2007 and to date three billion tonnes (Bt) of iron ore have been defi ned within the project area. Fortescue is fast-tracking the development of the ‘Solomon Stage 1’ project, with rail and mine construction commencing during 2011, and ore to be railed to Fortescue’s existing shipping operations at Port Hedland commencing in 2012. At a designed production rate of 60 Mt/a, the Solomon operation will be one of the biggest production centres of iron ore in the Pilbara.Deposit types include the three dominant mineralisation styles of the Pilbara province, being bedded iron deposits (BID), Channel iron deposits (CID) and detrital iron deposits (DID). All these mineralisation styles are present in large concentrations within the Solomon project area, and when mined will produce two product streams. These are a single product of CID, and a combined product from a blend of BID and DID material.This paper defines the geological characteristics of the Solomon iron deposits as recognised through the exploration and development of this vast resource over the three years since exploration commenced on the project.

Jul 11, 2011

By M Biesinger, R St C Smart

Diagnosis of the surface chemical factors playing a part in flotation separation of a value sulfide phase requires measurement of the hydrophobic and hydrophilic species that are statistically different between the concentrate and tail streams. Statistical methods, based on the monolayer-sensitive time of flight secondary ion mass spectrometry (ToF-SIMS) technique, have been developed towards this ultimate aim by measuring hydrophobic species (collector ions, dimers and metal complexes, polysulfides) as well as hydrophobic metal ions, precipitates and added depressant species. Reliable identification of specific mineral particles is central to this statistical analysis. A chalcopyrite/pyrite/ sphalerite mineral mixture conditioned at pH 9 for 20 minutes to study transfer of Cu from chalcopyrite via solution to the other two mineral surfaces, since this mechanism can be responsible for their inadvertent flotation in copper recovery, showed no statistical difference in the copper intensities on pyrite and sphalerite (selected from Fe and Zn images) after this conditioning. Principal component analysis (PCA) identifies combinations of factors strongly correlated (positively or negatively) in images or spectra from sets of data. In images, PCA selects these correlations from the mass spectra recorded at each of 256 ¦ 256 pixels in a selected area of particles. In the image mode, PCA has proved to be a much better method of selecting particles by mineral phase with clearer definition of particle boundaries due to multi-variable recognition. It has clearly separated a statistical difference in copper intensities between the sphalerite and pyrite phases. The PCA method has been applied to concentrate and tails samples collected from the Inco Matte Concentrator demonstrating extensive CuOH and NiOH transfer between the chalcocite (Cc) and heazlewoodite (Hz) minerals. Statistical differences illustrate the important discriminating depressant action of NiOH in flotation despite the activation of Hz by Cu transfer. The adsorption of the collector at specifically-identified Cu sites has been elucidated by the study. Importantly, the statistical analysis has been able to confirm some mechanisms and deny others proposed to control recovery and selectivity giving more focus on the control factors.

Jan 1, 2005

In the past few years the Rietveld method emerged as a routine tool for quantitative phase analysis (QPA) from X-ray diffraction data. Fast and reliable results became possible by combining modern computer technology and optimised mathematical algorithms with the fundamental parameters approach in the Bruker AXS TOPAS software. Here the routine analysis of bauxite raw material and of aluminium bath electrolyte is presented. The accuracy of bauxite quantification was tested by analysing the IUCr round robin sample. An agreement of better than one per cent was obtained for minor constituents and a maximum deviation of 2.5 per cent for the major phases. This is excellent agreement with expected results from weighting. Ten different phases were quantified in natural samples from Turkey with a precision better 0.5 per cent for the major phases and one per cent for the minor phases. Additionally, crystallite sizes were obtained from the peak profiles that give valuable information for the processability of the material. XRD data from solidified aluminium electrolytes were rapidly measured using silicon strip detector technology. With the LynxEyeTM detector full patterns were collected in 90 seconds and analysed with TOPAS. It is shown how to derive well-established measures such as bath ratio and excess AlF3 from the Rietveld results. These measures are widely used in aluminium production and readily available with very high precision. The excellent agreement with ALCAN reference data demonstrates the outstanding accuracy of the method. The mean deviation between here presented results and reference data is below 0.5 per cent for total CaF2, below 0.25 per cent for excess AlF3 and 0.02 for the bath ratio. The precision of the method was evaluated by repeated measurements.

Jan 1, 2008

By S M. C Verryn

Through the application of the Rietveld method, X-ray diffraction analysis has developed into a fully quantitative method for phase analysis of metallurgical products. The Rietveld method itself has progressed from an unstable method that required constant operator intervention to a stable and robust method suited even for routine process control. Knowledge of the crystal structures of the major phases is essential for Rietveld analysis, and these are well known for most minerals and major phases in metallurgical products. It provides the basic structural information necessary for the determination of mineral stoichiometry and for elucidating solid solution behaviour. Modern methods, such as simulated annealing and charge flipping, permits the determination of crystal structures from powder data. Unit cell data can be used where conventional microchemical analysis is unable to provide an answer to the extent of solid solution in ilmenite roasting. Unit cell data (by XRD) is used to determine the amount of roasting necessary for the development of magnetisation to be able to separate chromite from an ilmenite concentrate. Phase quantification is probably the most widely used application of XRD analysis. It is used for materials balance in the minerals and cement industries, and it is finding novel applications in the iron and steel industry. Applications of XRD in high-temperature metallurgical processes are increasing. In this paper the phase chemistry of iron ore sinters, the evaluation of subsolidus reactions in titania slags and the identification of furnace accretions are discussed. Despite the success of the Rietveld method in phase quantification, the method still needs further development in the quantification of closely related or polytypic phases. The quantification of pyrrhotite phases using various Rietveld programs still gives ambiguous results. This is also true for the different SFCA phases in iron ore sinters. Clearly the analysis of similar phases, differing only in the presence of weak superlattice reflections is still problematic.

Jan 1, 2008

By B McCreath

Industrial process water for the Commodore Coal Mine and the adjoining Millmerran Power Station is provided by pumping secondary treated sewage effluent 100 km from the Wetalla Sewage Treatment Plant near Toowoomba. (A separate source is used for potable water.) The effluent is not of sufficient quality for discharge to a watercourse, but it is suitable, with further treatment, for the mine and power station. In designing and constructing the pipeline, special emphasis was placed on preventing accidental spills or planned releases to the environment. The pipeline and associated works can transfer 1000 ML/annum for reuse in the coal mine and power station.

Jan 1, 2003

THE object that the writer has mainly in view in presenting this paper is to draw the attention of those connected with the technical side of the industry to the unsatisfactory and by no means up-to-date methods employed in estimating the tin contents of an ore. At the same time, what is regarded, from the writer's personal experience, as a satisfactory and reliable method is explained in detail. It is a curious fact that for the last 25 years tin·assay methods have made little or no advance, while those now in general use ill connection with copper and lead ores can scarcely be compared with those then obtaining, so greatly have they been improved upon. Though it. is not altogether expected that the method herein advocated will at once meet with general approval, the writer hopes the resultant discussion may bring out points that have hitherto escaped detection.FIRE METHODSThe old Cornish method of smelting with anthracite is now obsolete. The cyanide assay, although unreliable, is still much used because of its simplicity. In the Malaya many buyers of tin ores use the cyanide assay, the smelting being carried out generally in a benzine furnace. It is essential that the smelting with cyanide be performed at a low temperature. Even then, impurities, such as Sb2S3 and...

Jan 1, 1912

By P O. Andersson

Mining of sill pillars is more difficult than the ordinary mining. The sill pillar mining is performed under more difficult conditions and the mining of the sill pillar itself produces more problems; failure of the rock due to high stresses, difficulties in controlling the fill above, overall stability of the stope and special requirements on the technique for backfilling. Altogether this makes sill pillar mining technically difficult and often not profitable. A project was therefore initiated with the aim to increase the mineable ore reserve by making sill pillars mineable, both technically and economically. The project aimed at developing technique for already existing sill pillars as well as planned sill pillars. For the existing sill pillars a technique would have to be developed for mining beneath unstabilised fill. For sill pillars that would be created in the future, the most suitable mining method and methods of supporting or stabilising the fill in the stope above was to be chosen within the project.

Jan 1, 1998

By N McKenzie, E Taylor, S V. L Barrett, H Lagger, A Purwodihardjo

This paper discusses the temporary support design methodology for the largest road caverns ever built in Australia—the Lutwyche Caverns—part of the Airport Link project in Brisbane, Australia. The Lutwyche Caverns with a maximum excavated span of 27 m form a key component of this major road project, allowing on and off ramps merging with the underground highway. In addition to the two large span caverns, a 15 m soft ground tunnel with 5 m cover above the caverns and two 24 m deep burial chambers for the 12.4 m tunnel boring machines (TBMs) had to be built in record time at Lutwyche.The temporary support design methodology involved the use of a range of analytical approaches, including empirical methods to provide a starting point for design development, key block models to determine the potential influence of discontinuities on excavation stability and 2/3D continuum and discontinuum models to determine the potential influence of adjacent excavations and the proposed construction staging on the design. In addition, probabilistic analysis of potential kinematic instability using a discrete fracture network (DFN) approach was also undertaken to establish the critical block loads for the temporary lining, while the continuum and discontinuum models were used to design the support for the 1.5 m diameter rock pillar at the north end of the northbound cavern.The numerical modelling was undertaken in close conjunction with the contractor to develop the optimal construction sequence, considering the available construction equipment on-site and the overall project program requirements. Part of the presentation will further show the applicability of the developed design during construction (deformations, monitoring field observations) and lessons learned for future cavern construction in Australia.CITATION:Lagger, H, Purwodihardjo, A, Barrett, S V L, McKenzie, N and Taylor, E, 2014. Temporary support design for the largest road caverns ever built in Australia – the Lutwyche Caverns, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 399–410 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By D J. Brake

The correct specification and then selection of primary or major fans for an underground mine is a critical decision not only in terms of fan capital and operating costs, but also safety and reliability which usually has a major impact on mine production. In addition, fan manufacturers may spend tens of thousands of dollars preparing proposals for a purchase enquiry for primary fans especially where they have complete responsibility for the installation (turnkey projects). There are many good reasons to thoroughly and fairly adjudicate fan tenders. This paper describes the process to achieve this starting with the initial fan specification through to the final award.CITATION:Brake, D J, 2017. Fan specification and tender adjudication for mine ventilation engineers with particular reference to turnkey projects, in Proceedings Australian Mine Vent Conference 2017, pp 245–252 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By K Tanguturi, B Belle, R Balusu

Management of high rates of goaf gas emissions between 4000 and 6000 L/s of methane gas in longwall panels is a challenging issue, particularly in start-up areas of the panels. There is a need for investigation of the effect of various goaf gas drainage concepts and techniques, and development of effective gas drainage strategies for management of high goaf gas emissions in start-up areas of the longwall panels. This paper presents the results of various computational fluid dynamics (CFD) simulations that were carried out to investigate the effect of different goaf gas drainage strategies and combinations for gas management in the start-up area of the longwall panels. Results indicated that the gas (methane) concentration in goaf holes on the tailgate (TG) side vary between 50 and 75 per cent under the simulated field conditions with flat coal seam gradients. The results also indicated that operation of more goaf holes for draining the goaf gas on the TG side results in high ingress of oxygen and further reduction in gas concentration in goaf gas drainage holes. The simulations also included scenarios with goaf gas drainage holes on the maingate (MG) side, TG cut-through seal and near the start-up area. This paper presents the results of various goaf gas drainage strategies and discusses the effect of various combinations in order to develop effective goaf gas drainage strategies for gas management in start-up areas of the longwall panels.CITATION:Tanguturi, K, Balusu, R and Belle, B, 2015. Development of goaf gas drainage strategies for start-up areas of highly gassy longwall panels, in Proceedings The Australian Mine Ventilation Conference, pp 251–258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By A Tolley

Bauxite residue or ‘red mud’ is a by-product of the Bayer Process, the primary process of alumina refining. Due to its high alkalinity and variable composition, its storage and disposal poses high environmental risks to water sources, surrounding ecosystems and human health. The high alkalinity (pH 12–13) is a significant factor in its classification as hazardous waste; to mitigate this, Australian refineries have integrated neutralisation processes into bauxite refining. Both sea water and carbon dioxide neutralisation processes are applicable. Multiple studies have demonstrated pH reduction from 12–13 to 7–10, depending on the method. The key advantages of CO2 neutralisation are that it allows for carbon sequestration and is more effective when utilised as a pre-treatment for recovery of metals, while sea water neutralisation is more established and has been integrated into two Australian refineries. This paper proposes the application of the bacteria Exiguobacterium oxidotolerans for bioleaching of iron from hematite in bauxite residue. The genus Exiguobacterium is characterised by its high levels of adaptability, halotolerance and alkaliphilic nature. E. oxidotolerans is successful at eluting Fe2+ from hematite via reductive dissolution, which complexes with oxalic acid produced during metabolism. This aquatic bacterium presents a novel process pathway for iron elution due to direct interaction of E. oxidotolerans with hematite via the cell membrane and operates within the pH range of neutralised red mud. The proposed mechanism is extracellular electron transfer, a microbial metabolic process where electron transfer is facilitated between bacterial cells and extracellular material. Currently this is being investigated for promotion of seaweed growth in coastal environments as soluble iron aids and fortifies colonies. This has potential downstream applications for cleaner iron and steel production. While theoretical, this paper explores the neutralisation, bioleaching and application of the Fe(II)- and Fe(III)-oxalate complexes formed.

Sep 18, 2023

By A Keogh, P Allen, P Stoker

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Private equity (PE) firms are comparatively free of mandatory requirements for the level and scope of due diligence applied prior to making investment decisions in minerals projects when compared to listed entities, sovereign funds or financial institutions adopting the Equator Principles (Equator Principles Association, 2013). While this freedom allows for flexibility, agility and innovation in making investment decisions, it can also expose PE firms to material risks that may impact their ability to successfully list the projects or attract later financing.Financial institutions and investors with mandatory due diligence and disclosure standards may refrain from investment in or acquisition of a project if it fails to meet various performance requirements. There are many high-profile projects that have suffered significant write-downs on book value after acquisition because specific non-mining issues were not adequately assessed. Thus, a PE firm may be left with an asset that is difficult to divest and incapable of securing development finance.PE firms can manage this risk by being aware of the growth trend in the adoption of ‘international standards’ in addition to host nation standards and legislative requirements. This paper outlines key issues for PE firms to address to maximise the chances of obtaining funding or successfully taking an exploration or mining project through to listing or divestment. Two steps are required: identification of gaps in performance and priority matters of interest to financial institutions and development of action plans to ensure that the priority requirements are met or capable of being met.A PE firm can set its project for success by understanding the social and environmental performance requirements of international standard financiers and by setting the project on the right path to meeting these requirements, and thus making it an attractive investment.CITATION:Allen, P, Stoker, P and Keogh, A, 2015. Setting for success – private equity exploration and mining project buy-in to listing and divestment , in Proceedings PACRIM 2015 Congress, pp 93–100 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By U Berg, T Neumann, Y Song

Eutrophication of water bodies is one of the most severe environmental problems worldwide. It is well known that the availability of phosphate, as the limiting nutrient, is crucial for increased primary production and eutrophication. Calcite exhibits positive surface charge in most natural waters and can therefore be used for phosphate immobilisation. In this study, sorption experiments were performed in order to test different calcite materials regarding their suitability for use in restoration of eutrophic lakes. These short-term experiments were performed under different hydrochemical conditions (pH, SICC, initial dissolved P concentration) and with varying calcite properties (specific surface area and amount) in order to predict the long-term stability of the Ca-P-bonds. Peculiar shapes of isotherms that could not be explained only by adsorption processes were detected in the individual experiments. Depending on the residual P-concentration in solution, the isotherms can be divided into three sections indicating different processes responsible for the P-fixation on calcite surfaces. Adsorption prevails in equilibrium with lowest residual P-concentrations. The inflection of the isotherm at moderate residual P-concentrations suggests that precipitation and transformation of a Ca-P compound becomes dominant. This is supported by characteristic Ca/P-ratios for different Ca-P-compounds (b-tri- calcium-phosphate, octa-calcium-phosphate). On the new surface, phosphate ions again are fixed by adsorption. The observed transformation of P-bonding is crucial for sustainable phosphate immobilisation on calcite surfaces. While pure adsorption processes are reversible, the development of a thermodynamically stable Ca-P-phase, like hydroxylapatite, will lead to a lasting immobilisation of phosphate.

Jan 1, 2008

The Gj0vik Olympic Mountain Hall is the world's largest underground cavern for public use and was created primarily to facilitate the ice hockey tournaments for the 1994 winter Olympics in Norway. The cavern has a span of 61 m, is 91 m long and is 25 m high. Ordinarily, rock caverns have a span width of 15 to 25 m, however, temporary mining caverns of up to 60 m have been excavated and natural caves with even greater dimensions occur. The Gj0vik Olympic Mountain Hall is unique as it is for public use with a capacity for 5800 spectators. Blasting was conducted with a high production rate at normal costs due to detailed planning and strict supervision of each round. The initiation system and vibration monitors were the main tools to control vibration levels and to facilitate a high production rate. It was of utmost importance that the rock remaining in the roofs and walls was of high quality after blasting to avoid rock fall, rock slides and excessive maintenance work.

Jan 1, 1995

By M A. Gontalves, A F. D C Varajpo, S A. Stachissini

Clays from the Santa Elena Peninsula, south-east of the Ecuador coast, were investigated with a view to identifying their main mineralogical, physical, chemical and textural characteristics as well as their potential for industrial use as adsorbents. Identified as calcic bentonites, two representative samples from the Tosagua Formation (Oligocene to Lower Miocene) were selected for acid activation trials. The selection criterion was based on the greatest amount of clay fraction (<2 ¦m fraction) associated with the greatest content of montmorillonite. For the activation treatments, HCl and H2SO4 solutions of 4, 6 and 8 N were used in a stirred glass reaction vessel with the clay sample under reflux during four hours at temperatures of 70¦C for HCl and 85¦C for H2SO4. Mineralogical analysis by X-ray diffraction (XRD), chemical analysis by X-ray fluorescence (XRF), differential and gravimetric thermal analysis and measures of density, surface area and porosity indicated the changes occurred in the crystal structure of the montmorillonite. The acid treated clays were utilised in trials of purification and decolourisation of soybean vegetable oil in a ratio of 2:100 (clay/oil) at 90¦C for 30 min, under constant stirring. After centrifugation of the suspension, the wavelength of the bleached oil was measured by UV-visible spectrophotometer and the bleaching capacity of the clays was determined. The best bleaching capacity of the samples was obtained with 6 N H2SO4 acid-activated clays. The bleaching capacity was compared to Tonsil, a commercial acid-activated clay and similar results between them evidenced the potential industrial application of the Ecuadorian clays to bleaching of vegetable oil.

Jan 1, 2008

The accuracy of an ore reserve is only as good as the geologist's understanding of the deposit. The methods that are applied to resource and reserve estimation reflect that understanding. At the Olympic Dam copper-uranium-gold deposit in South Australia, evolution in the understanding of the controls on mineralisation coupled with the changing demands of the project have led to changes in the approach to reserve estimation. The project has moved into a phase where detailed stope mining reserves are now required as distinct from global ore reserves. The complex nature of the mineralisation and the large amount of data demand that all available information be readily accessible in a flexible format. To enable the selective manipulation of geological and assay information and its characterisation, a relational database has been developed. For reserve calculations themselves, initial computations were based on a system derived from that used for the Kambalda nickel orebodies. The Olympic Dam system differed mainly in the use of statistical analyses in the estimation of grade instead of the previous polygonal area of influence weighting method, Three dimensional weighting techniques are now being used for local reserve estimates. Flexible facilities for raw data handling combined with grade estimation techniques which are commensurate with the mine geologist's understanding, produce detailed gridded and contoured ore zone models suitable for reserve calculations and stope designs.

Jan 1, 1987

In a ætypicalÆ gold deposit each tonne of ore will contain tens of millions of very fine gold particles, whereas; at Bendigo the majority of gold in each tonne of ore is present in just five to 15 very coarse gold particles, a distribution more akin to diamond deposits. At Bendigo the minimum sample size required for good assay repeatability is estimated at 4.5 t for each assay. Drill core samples are several orders of magnitude too small to generate representative assays.The drilling data are characterised by a nugget effect approaching 90 per cent, a very skewed distribution and, on average, under-report in situ grade by 50 per cent to 75 per cent. Since 2002 Bendigo Mining NL has completed 47 000 m of diamond drilling, 1200 m of on reef development, collected and processed 100 bulk samples (150 t each), 800 mini bulk samples (50 kg each) and processed in excess of 25 000 t of ore through a pilot plant. The results of this work have provided the information required to develop and verify a robust grade estimation procedure. No standard geostatistical manipulation of the drilling assay data can generate an accurate grade estimate as the samples and associated assays are not representative of the ore being sampled. The recognition of this fact was critical as a radical transformation of the raw drill assay data was required to develop a workable methodology for grade estimation in such a high nugget environment. The aim of the transformation was to reduce the nugget effect and high variance and so approach a lognormal assay distribution. Ideally the average drill grade would approximate actual in situ grade and the assay distribution would reflect actual grade distribution within the reefs. Following the data transformation simple block modeling within the defined resources allows grade estimates to be made that can be used in the estimation of Indicated Resources and hence Probable Reserves. The grade estimates have been checked by extensive bulk sampling and processing of 25 000 t of ore (three per cent of total resource) through a pilot plant with planned full scale mining to provide the ultimate verification.

Jan 1, 2004

Leadership challenges for mine management over the next decade will be primarily about doing more with less labour. This will require a greater focus on people leadership and management, reducing uncertainty by evening out employment peaks and troughs, understanding and addressing our demographic destiny and its implications whilst identifying and holding onto our mission critical employees, managing creativity and accepting diversity whilst providing flexibility in employment for work-life balance. Greater emphasis will also be required on the non-technical social skills of complex interactions with community and education providers and finally a greater emphasis on forecasting and planning for the provision of future skills needs. Skills needs will become an ever increasing priority in risk management as retention starts with attraction and remember: SATISFACTION = REALITY                                EXPECTATIONS These are the challenges and opportunities for leadership and mine management of the 21st century to assist in better meeting and maintaining our human resources needs and thus contributing to the sustainability of the sector in Australasia.

Jan 1, 2006