Search Documents

Any hypothesis for the origin of the Otago gold-quartz lodes must account for the following observations. 1. Southeast of Glenorchy, where the schists hosting the lodes are comparatively unaffected by Neogene Alpine Fault deformation, the dominant strike of the vein systems is NW-SE, parallel to the axis of greatest post-metamorphic uplift in the Otago Schist belt (Paterson, 1986). 2. The lodes are fault-hosted, with some developed along steep, low-displacement normal faults (eg Barewood, Bendigo, Nenthorn), implying NE-SW extension, and some developed along low-angle thrusts (eg Macraes) implying, in apparent contradiction, NE-SW contraction (Teagle et al, 1990). 3. The mineralising fluid was of metamorphic origin (McKeag and Craw, 1989), but while some of the lodes developed in a mesothermal environment at considerable depth (eg ~10 km for Macraes), others appear to have formed at very shallow depth (eg <1 km for Nenthorn) (Craw and Norris, 1988). 4. The timing of the mineralisation is generally poorly constrained but postdates the main Rangitata schist metamorphism. It probably initiated during early Cretaceous exhumation and unroofing of the schist belt (140 - 120 Ma?) and may have continued well into the Tertiary (Craw, 1989). Estimates for the relative ages of the different lodes are largely speculative but, based on pressure estimates from fluid inclusion studies, Macraes likely represents the deepest and oldest lode system while Nenthorn (just 12 km to the southwest) is perhaps the shallowest and youngest (Craw and Norris, 1988).

Jan 1, 1992

By Bhattacharyya A. K

The current methods for predicting pillar strengths are reviewed. A two-dimensional model, based on the Mohr-Coulomb failure criterion, is proposed for determining the compressive strength across the width of a long pillar. The model can be used to determine pillar strength and the depth of the crushed (ie yielding) zone from the pillar edges. The values of the parameters in the model, namely the cohesion and internal friction angle of the coal seam, friction angles at the contact of the coal seam with the roof and floor are determined by matching the strengths predicted by this model with the Bieniawski pillar strength formula for pillar width to height ratios up to 5. It is found that the derived values of these parameters are quite close to the results from laboratory tests. Based on the model, a preliminary analysis of pillar stability is made.

Jan 1, 1995

By C Balci, D Tumac, A Sheterpour-Mamaghani, E Dogan, A Kocbay, T Erdogan, A Gumus, H Copur, E Altintas

Excavation of vertical and/or inclined shafts in the underground structures requiring careful design and planning. Raise Boring Machines (RBMs) are commonly used for excavation of shafts for different purposes such as ventilation, orepass, and human-material transportation. Proper selection and accurate performance prediction of RBMs are two main parameters affecting the cost estimation and planning/scheduling. Indentation test is one of the most preferred methods that can be used to predict advance rate of RBMs. This study aims at suggestion of new prediction model for instantaneous penetration rate of RBMs based on indentation tests. Different rock (core) samples (with different geological origins) are obtained from the raise boring application projects in Turkey; then, the indentation tests are carried out on them by using a real-life insert (button), which is used in reamerhead cutters investigated in this study. Finally, the statistical relationships between the field performance and the indentation indices are investigated. The study indicates that the brittleness index (the ratio of maximum applied force to corresponding penetration) can be used to predict instantaneous penetration rate of RBMs used in the vertical raise bored shafts excavating rocks having uniaxial compressive strength lower than 100 MPa.

Nov 29, 2022

By Sahoo K. C

Traditionally, the blast furnace (BF) has maintained a dominant position as the primary source of iron units. Notwithstanding the efficient nature of the process in respect of its material and energy consumption, the conventional blast furnace route is faced with limitations such as stringent quality metallurgical coke, high capital investment, etc. While BF will continue to retain its predominant position as the foremost ironmaking technology, the alternate processes may also have a role to play. Direct Reduced Iron (DRI) or sponge iron industry is all set to take a firm root in India as one important solution to the problems of shortage of metallurgical coal and ferrous scrap and high investment costs faced by the country's steel industry. The commercial proven DR processes coupled with electric arc furnace (EAF) steelmaking have also offered a viable alternative to the blast furnace - basic oxygen furnace (BF - BOF) route for the installation of integrated plants under specific local conditions. The performance and efficiency of DRI processes mainly depend upon the chemical and physical behaviour of the raw materials especially the iron bearing materials. Iron oxide pellet and sized lump ore constitute the oxide feed stock, while pellets form an ideal feed stock for direct reduction, use of lump ore is economically advantageous because of its lower price. National Mineral Development Corporation Limited (NMDC), being one of the major producer of iron ore in the country since last four decades, has established technology and developed process flowsheets for production of suitable calibrated lump ore for DRI production, besides supplying the natural lump ore for conventional blast furnace requirements. In addition to the above, extensive pilot plant tests have been carried out at the R&D Centre of NMDC for preparation of iron ore concentrates suitable both for direct reduction and blast furnace grade pellet feed using the iron ore fines from its own mines and as well as from the other iron ore mines in the country. For utilisation of the huge quantity of slimes generated in its ore processing plants, NMDC has planned to set up the first commercial plant adopting the smelt reduction process (ROMELT Process) for production of pig iron from Bailadila slimes. The paper mainly deals with various beneficiation techniques adopted for production of DRBF grade pellet feed from iron ore fines. Also presented in the paper, the extensive work carried out at R&D Centre on preparation and evaluation of calibrated lump ore (Natural Pellets), based on which, suitable modifications are incorporated in the ore processing plants of NMDC for production and supply of the same to sponge iron industries.

Jan 1, 1999

By P Fuller, A R. Penney

Re-commencement of mining in the Western Zone of Beaconsfield Gold Mine following a seismically-induced rockfall fatality in April 2006 required a change of mining method involving drilling and blasting from specially developed drives in the footwall of the orebody. Broken ore is mucked remotely from ore drives on each level. Support in the footwall drives is required to maintain stability during their development and as stopes are retreated, which increases induced stresses and further seismic events are triggered. The paper outlines the challenges involved and methods used to select the footwall drive support to handle both static and dynamic load demand. The importance of load development in the support system, its displacement capacity, the compatibility of support elements and energy absorption capacity of the support system are highlighted. It is usual in any support selection process to ensure that capacity exceeds demand to create a factor of safety. In this case the demands on the system relate to load, displacement and energy absorption and the support system capacity for each must ensure that appropriate factors of safety for each are achieved. The paper shows how these factors are not independent and that selecting a high factor of safety for load can lead to compatibility problems with support elements in the support system.

Jan 1, 2008

By T Laurencont, C Unger

The Mount Morgan minesite, located approximately 40 km SW of Rockhampton in Central Queensland, comprises 270 ha of unrehabilitated land which is the currently the major source of acid mine drainage run-off and seepage to the adjacent Dee River. Additionally, the minesite hosts an Open Cut Pit which contains 9000 ML of acidic and metal-rich water. In the absence of active management of water in the pit, there is a 50 per cent probability of an uncontrolled spill occurring in future years. The development of a contingency plan for management of overflow from the pit in the short term, has incorporated findings from numerous studies relevant to the Open Cut Pit including, but not limited to, water balance, contaminant source identification, toxicity testing, water quality profiling and limnological modelling, and estimates of probability of overflow. Extensive stakeholder consultation and peer review were also undertaken during the formulation of the contingency plan. The medium-term goal of lowering the water level in the pit to reduce the current high probability (50 per cent) of uncontrolled overflow to acceptable levels of risk is proposed to be achieved by a campaign of chemical water treatment. The treated water will be discharged to the Dee River, and sludge returned to the pit. The methodologies used for the selection and development of the water treatment process, that is proposed to involve treatment with lime, are described. Water treatment is the short- to medium-term component of a long range rehabilitation plan for achieving a negative pit water balance, and sustainable management of acidic water across the whole site. Achieving this ultimate goal will involve: reducing the inputs of water to the Open Cut Pit such that the annual water balance is zero or net negative, thus removing the need for water treatment in perpetuity; maximising, by surface rehabilitation works, the quality of run-off reporting to the Dee River; and minimising the volume of acidic seepage reporting to the seepage interception system. Possible strategies for achieving this long range goal consistent with overall site rehabilitation objectives are currently being developed and costed.

Jan 1, 2003

A methodology for the fatigue life estimation of load haul dumpers, employed in underground platinum mines, has been developed and applied. This method entails the quantification of operating conditions by means of stress measurements. The measurements are then translated into a fatigue loading factor for a finite element model. The results of this analysis are then used to compare all the critical connections in the structure to detail categories in relevant fatigue codes, and predict a life in operating hours for the vehicle structure. The method was applied on a specific model and the results of this analysis were compared to actual failure occurrences with reasonable accuracy. It is intended that the methodology be embedded into performance specifications and purchasing contracts and that technology transfer to OEMs be achieved. Based on the experience of this project and other similar exercises it is estimated that structural life expectancies may be increased across a typical fleet of trackless mining vehicles (LHDs, drill rigs, utility vehicles, dump trucks) by at least 20 per cent.

Jan 1, 2005

Since its inception in 1962, the Julius Kruttschnitt Mineral Research Centre has adopted the view that an effective method of training highly qualified engineers for the mineral industry is the pursuit of postgraduate research programmes conducted in operations, that is, in the mines and processing plants of the industry which the research serves. The paper describes how this is achieved in practice, at little or no cost to the taxpayer, and explores the strengths and weaknesses of this approach in the context of a dual mission for the Centre: 1. The postgraduate training of engineers for the mineral industry. 2. The production of useful R &I) for the mineral industry. Topics discussed include financing, relationships with industry and Government, the maintenance of academic excellence, research style, the marketing of research, and limits to growth.

Jan 1, 1989

By A K. Bayer

When the human eye fails in the evaluation of quality parameters in the extraction of minerals the use of laser-induced fluorescence analysis (LIF) can supply more detailed information on the composition of rocks. On the basis of measurements of selected raw materials engineering concepts for the use of this method in the mining industry as an innovative system for horizon control of mining machines will be described and the most important analysis parameters, influencing factors and interference variables are presented.

Jan 1, 2003

By J Charbucinski

Commonwealth Scientific and Industrial Research Organisation (CSIRO), Exploration and Mining, has developed nuclear spectrometric techniques for borehole logging. The paper reviews the latest developments of this technology for the metalliferous mining industries. The SIROLOG logging system developed by CSIRO Exploration and Mining has been commercialised and is available to the mining industry.

Jan 1, 2000

The accurate determination of trace level gold in ores, metallurgical samples and process solutions is required because of the value of gold, the efficiency of the cyanide leach process and because of the high gold recovery from these cyanide solutions. It is thus necessary to routinely analyse geological and metallurgical samples with gold concentrations of 3 g tonne (ug g- 1ppm) and process solutions with a gold concentration of 0.01 mgL 1 (ppm) preferably with sufficient accuracy to quote at least two significant figures. Several techniques have been reviewed for their suitability for the routine gold analysis of these samples which also contain signif- icant concentrations of other ions. The classic fire assay technique has achieved the respect and confidence of mining personnel because of the results achieved by very experienced assayers. Other extraction and concentration techniques have now been shown to be equally effective. The use of instrumental analytical techniques particularly atomic absorption spectrometry have shown that cheaper procedures, which are as reliable, are now available to gold producers for the routine analysis required to maintain an efficient gold recovery process.

Jan 1, 1982

By M Heidari, M Ataei

Today, the selection of a mining method is a multi-criteria decisionmaking process, with many factors in this process connected to each other. These trends do not have a high degree of confidence. In this study the analytical hierarchy process was used to select the suitable mining method for anomaly No 3 of Gol-Gohar iron mine of Iran. The results of this study show that gathering all existing information from the exploration stages and using AHP technique, the open pit mining method is the mining method for this anomaly.

Jan 1, 2003

By P N. Holtham

Magnetic separation is routinely used in the processing of titaniumminerals, and the efficiency of these operations can be determined bymeasuring the magnetic properties of the process streams. The valuable components in the feed to a titanium minerals plant have specific magnetic susceptibilities ranging from -10-9 m3 kg-1 (zircon) to 10-6 m3 kg-1 (ilmenite). However, in an industrial environment, in which the mineral temperature may range from 20 to 120¦C, it is difficult to measure susceptibilities lower than about 10-7 m3 kg-1. Hence laboratory testing of spot samples from magnetic separators is currently required to obtain accurate performance data. This is an inherently slow process and where feed grades are variable, optimum performance of magnetic separators is generally not achieved.This paper describes the development of an inductance-basedinstrument for measuring very low levels of magnetic susceptibilityon-line. The signal from the instrument can be used for process control purposes to maintain optimum magnetic separator performance.A prototype instrument has been installed in the zircon scavengercircuit in an Australian titanium minerals plant. The circuit consists of a roll magnetic separator treating a feed consisting mainly of monazite and stained zircon. The monazite-rich magnetic fraction is returned to the mine site for disposal, while the non-magnetic fraction is recycled to the zircon wet circuit. Splitter positions in the separator are adjusted when the final zircon product fails to meet specification, or the magnetic fraction contains more than 30 per cent zircon. Weekly composite grain counts show that sub-optimal operation of the magnetic separator results in significant zircon losses into the magnetics fraction.Using the instrument, the zircon content of this stream can now beaccurately determined from the measured magnetic susceptibility,provided a correction for the effect of mineral temperature is applied using the Curie - Weiss relationship.

Jan 1, 2001

About 60 persons are admitted to the graduate course every year after passing the entrance examinations. The entire course of studies is free of charge and the universities provide accommodation for the students who need it. The five years of studies are divided into 10 semesters. One semester lasts 15 weeks. Automatics can be studied at three separate faculties. At the University of Mining and Metallurgy, it is offered by the Faculty of Electrical Engineering, Automatics and Electronics as well as the Faculty of Mining and Metallurgical Machines (metrology can also be studied there); at the Silesian Technical University in Gliwice, the Faculty of Mining offers the course. The educational plans and programmes comprise 3 groups of subjects: common for a given course of studies (foreign languages, political science and the basic technical knowledge) common for the speciality and subjects of diploma courses. The whole time of studies covers about 4400 hours excluding 3 periods of professional training and the physical training. The classes, laboratory classes, seminars and design classes are obligatory and the attendance is strictly checked. Students may extend their knowledge by participating and working in the Science Clubs. The students' work is checked not only during the classes but also by the examinations held at'the end of respective semesters. Those who fail the exams can repeat them only if very important reasons are presented. At the very end of the studies there is a diploma examination together with a discussion on the diploma thesis, written by the student. The successful result entitles the student to recieve the title of "magister inzynier",M.Sc. of his speciality. The graduates, after working for 2 years, can attend another course of studies lasting 2 semesters and called "Postgraduate Course", or start "Doctoral Studies" finished by the defence of a doctor's thesis. In'these cases the expenses are usually covered by the graduates' employers.

Jan 1, 1985

By Z Endut, T F. Ng, G H. Teh, J H Abdul Aziz

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Gold mineralisation at the Penjom gold deposit in the Central Belt of Peninsular Malaysia is hosted in structurally-controlled quartz-carbonate veins that display a variable degree of overprinting events under a ductile-brittle regime. Mineralised veins are categorised into two main types: shear and extension veins. Shear veins are interpreted as forming during the fold and thrust episode (D2 event) along the bedding and the Penjom Thrust ore zone. The shear veins are associated with discordant extension veins. In addition, NE- to NNE-trending splays and Penjom-Thrust-parallel reverse-dextral and locally NNW to N–S reverse-sinistral faults overprint earlier vein events, forming a new episode of extensional veins during the D3 event. This is mostly at the fault contacts of intrusives, either as shallow-dipping or vertical-sheeted stockwork or brecciated veins. At least two episodes of faulting comprising D4-D5 are evident, which postdates the main episodes of veining and mineralisation. This is indicated by a series of late episode N–S-trending sinistral and oblique to normal faults that transect and displace the Penjom Thrust and the folded footwall sequence at low angles, and are interpreted to be responsible for intensive vein deformation along the Penjom Thrust and displacement of the orebody. Structural interpretations of mineralised veins suggest that the veins were formed under a compressional to transpressional regime, with later post-vein displacement in a transtensional to extensional regime. Vein formation in response to deformation observed at Penjom reflects regional structural deformation within the Central Belt of Peninsular Malaysia and specifically along the Bentong-Raub Suture zone.CITATION:Endut, Z, Ng, T F, Abdul Aziz, J H and Teh, G H, 2015. Style of veins in Penjom gold mine, Malaysia – implications for gold mineralisation and structural episodes, in Proceedings PACRIM 2015 Congress, pp 507–514 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By S Leichliter

La Colosa, Colombia is a large gold-porphyry deposit currently undergoing feasibility studies by AngloGold Ashanti. This period of development allows the opportunity to apply innovative and emerging testing and modelling methods to provide a predictive geometallurgical recovery model for the deposit. By partnering with the AMIRA P843A Geometallurgical Mapping and Mine Modelling (GeMIII) research project, the geological and mineralogical data are analysed with respect to liberation and recovery methods. This will allow the variability in the geology and mineralogy of the deposit and key relationships recognised in the data to be included in the development of a model to help predict recoveries of the gold. Many aspects of the gold mineralisation such as gold paragenesis, associations, grain size and texture are determined and analysed using optical microscopy, Mineral Liberation Analysis (MLA), and laser ablation (LA-ICP-MS). At La Colosa the gold has been located in sulfides (eg pyrite, pyrrhotite, and chalcopyrite), silicates, along silicate phase boundaries, and among the pyrite-rich intermediate argillic alteration. Further testing and analysis will also determine if ‘invisible’ gold is present in the pyrite, pyrrhotite, and chalcopyrite. Recovery methods can also be determined and tested after combining the results of mineralogy tests with other data (eg results of comminution tests). Indices for the mineralisation and recovery are developed using image analysis and analytical testing. These indices are correlated with recovery data from the company to develop a predictive block model for recovery. The goal is to develop cost-effective, efficient methods to analyse the mineralogy and geology of the deposit; understand the variability in the mineralogy, geology, and recovery; and construct a predictive geometallurgical recovery model.

Sep 5, 2011

By E Kabwe, M Karakus

Deep hard rock underground mines tend to experience high stress as such drives exhibit dynamic responses attributed to a rock burst variant (strainburst). This dynamic behaviour is difficult to predict, and every effort is made to devise the appropriate dynamic support system for its associated failure restraint. This paper outlines the back analysis and the support scheme design for an underground decline that exhibited damage from a dynamic strainburst occurrence. It employs a decline section that experienced a dynamically loaded strainburst that initiated rock fragment ejections. The procedure involves a preliminary structural analysis, a seismic intensity measure, and a rock mass simulation to determine the static stress concentration and ground support system response. The numerical simulation is conducted in FLAC3D which employs the advanced strain-softening IMASS constitutive model governed by two Hoek–Brown (HB) bounding yield surfaces. To account for the post-peak brittleness response associated with strainburst the plastic strain multiplier () is adjusted to 0.0 < < 1.0. The back-analysis shows that the occurrence was initiated by a low-intensity seismic wave that superimposed an extra stress component to the initial static stress which triggered rock fragment ejections. Additionally, the appropriate support scheme comprised of Weldmesh, Fibrecrete, static (split set) and yieldable (Kinloc) reinforcements is recommended and implemented. Thereafter, the bolt’s efficiency is evaluated based on the axial force and elongation capacities and then compared with the published bolt performance data. The evaluation results show that the maximum bolt axial force (0.1 per cent) and elongation (0.006 per cent) are below the designed capacity and rupture strain.

Nov 29, 2022

By E N. Sparg, O D. A Deuchar, F Needham

Decline shafts are an attractive option to both new and existing mining operations where there is a need to access an inclined orebody deposit via on-reef development so as to generate a return in the shortest possible time. There are many different technologies that are available to transport men, material and rock in incline shafts. This paper focuses on the applicability of two hoisting technologies for decline shafts, namely endless and direct rope systems. The pros and cons of each system are reviewed. A common concern with direct rope haulage systems is the possibility of generating slack rope during deceleration. This paper illustrates the issues involved in designing a system so as to avoid the possibility of slack rope. In conclusion, the key factors relevant to the selection of endless or direct rope haulages for a particular decline application are reviewed. The paper is a joint submission by FFE Minerals-Vecor and Qualter Hall UK.

Jan 1, 2005

By G Johnson, S Michalek, N Redman

As the modification of the 2009 Mill OperatorsÆ Conference theme from æmilling through the boomÆ to æthe boom û experience gained and lessons learnedÆ exemplifies, comminution practitioners are facing a series of challenges in the dramatically changing mining environment. One of the main problems plant managers have been facing during the boom times has been the severe metallurgy skills shortage and high staff turnover, both factors that can cause difficulties in mill liner management. Many of todayÆs mill managers are now also more than ever faced with the need for cost-cutting in order to continue operating viably. Amongst other potential target outcomes such as maximised throughput, MillMapperÖ, a tool for mill condition monitoring and mill performance optimisation, can be utilised to address these issues. This paper demonstrates how MillMapperÆs quantifying decision making tools can serve to be in control of managing mill liner and production issues, and how it can form the basis for mill cost savings without the risks normally associated with conventional methods or the lack of using any condition monitoring methods. MillMapperÖ is currently being referred to at a rate of approximately 150 surveys and associated reports per annum at processing plants in Australasia, South America and Africa. Examples throughout the paper provide insight into how the presented sample set of users have extracted benefits that could have otherwise not been safely or at all achieved.

Jan 1, 2009

By Y Yamaguchi, S Nomura, M Matsumura, C Kamijo

In order to increase productivity and decrease reducing agent rate (RAR) of blast furnaces, slag content of sinter ore must be decreased. However, gangue content in iron ore tends to increase because of resource depletion. Therefore, amount of high-grade concentrate in sinter ore feeds should be increased, but this situation causes a decrease in permeability of the sintering bed so that the productivity of sinter process decreases. In order to increase the amount of concentrate, NSSMS has developed the P-type separate granulation method, RF-MEBIOS and SPEx II technologies. These technologies have been introduced to actual sintering machines. In this report, a new technology using microparticles of iron ore is proposed to increase the amount of concentrate in sinter blends. Basic experiments simulating the sinter making process using microparticles of iron ore were undertaken. Crushed pisolite, containing &gt;60 wt per cent -10 µm was prepared for binder. The pisolite microparticle binder was mixed with another Australian sinter feed ore in a high-speed agitating mixer. They were mixed for about one minute, and then granulated using a pan pelletiser. After that, they were added to another raw material mixed by a drum mixer, and then charged in a pot for a sinter pot test. As a result, when the amount of concentrate increased from 13 wt per cent to 20 wt per cent, productivity was almost kept constant using pisolite microparticle binder.CITATION:Kamijo, C, Yamaguchi, Y, Matsumura, M, Kawaguchi, T and Nomura, S, 2017. Development of an iron ore microparticle binder for increasing the concentrate content of sinter blends, in Proceedings Iron Ore 2017, pp 69–74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017