Search Documents

By E Villaescusa, A Kusui

The depth of underground mines has been increasing due to several factors, such as material demand growth and improving technology. It is a challenge to understand severe failure mechanisms such as spalling, which is caused by induced high stress. To investigate this failure mechanism under high stress conditions, intact rock blocks with small size tunnel were tested at the Western Australian School of Mines (WASM). The range of rocks, such as sandstone and granite, were drilled (200 mm hole) and tested using a servo-controlled 450 t capacity INSTRON machine. The acoustic emission sensors were attached to the block mass during the experiment to investigate the seismic response prior to spalling failure. The effect of the ground support system towards the failure was also examined by comparing the seismic response of the various ground support schemes.CITATION:Kusui, A and Villaescusa, E, 2016. Seismic response prior to spalling failure in highly stressed underground tunnels, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 689–694 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Bure R

Approximately 2.4 million ounces of gold and 11.3 million ounces of silver have been produced from the Umuna Lode by Misima Mines Pty Limited between June 1989 and the end of Decemeber 1996. Reserves remaining at the end of December were 32.1 million tonnes at 1.0 gram per tonne gold and 9.7 grams per tonne silver. To attain precious metal production of this volume, an estimated K60,000,000 (1996 Kina) was spent on exploration alone. from the 1940s to the present day. Exploration expenditure for the 1996 calendar year was approximately K4,400,000. With such a large investment in exploration, large quantities of data were generated and stored in various forms. To make best use of this data, it was necessary to organise and systematically store this data in a form compatible with a modern Geographical Information System (GIS). The Umuna Lode on Misima Island is a low sulphidation gold- silver deposit dated at 3.5 ¦ 0.2 Ma. The deposit is controlled by the 50 to 100 metre wide Umuna Fault- a moderate dipping, brecciated clay- chlorite- carbonate altered, normal fault zone. There is approximately 230 metres of mostly dip slip offset on this fault, which is measurable by the offset of the Cretaceous schist, marble and greenstone host sequence. Late Miocene microdiorite spatially related to the Umuna Lode does not appear to be genetically related to the gold- silver mineralisation. GIS was introduced to Misima at the end of 1995 and until recently has been mostly used for data storage and retrieval, the over- laying of various data sets to assist in targeting prospective areas, and as a drafting tool. The use of data-driven, predictive data analysis is the most recent effort in maximising the use of the extensive Misima database. By characterising the key controls and properties of the Umuna- type mineralisation, a Weights of Evidence, data-driven analysis produced a prospectivity map of Misima Island. The purpose of this map was to identify prospective areas yet to be explored and to assess the effectiveness of exploration to date.

Jan 1, 1997

IN presenting the following short paper the writer hopes to illustrate some uses of explosives in industrial work under conditions different to those prevailing on mining fields. This paper is based on experience gained at the Newcastle steel works of the Broken Hill Proprietary Company Limited. The management had decided that as soon as No. 2 blast furnace which is of an improved design was ready to be put into commission, No. 1 blast furpace was to be dismantled and reconstructed to a similar design to No. 2 furnace. This reconstruction entailed the removal of the brick lining of the furnace shaft, and, also the removal and disposal of the,"salamander" and hearth-lining. For the information of members who may possibly be unacquainted with the term "salamander," it might be explained that this term is used by iron metallurgists to denote the mass of iron and slag formed at the- bottom of the furnace, whilst in commission.The method of disposal depends upon the size and nature of the salamander, and in the case under review it was decided to bury it below the hearth of the 'furnace' to be reconstructed. A passage-way was made in the concrete walls of the cast house, and the sand-filling of the cast house removed sufficiently to allow of the concrete foundations of the furnace being reached. This passage-way was extended until the hearth was encountered. The next operation was the removal of the hearth-lining below the salamander. The removal of the concrete was not difficult...

Jan 1, 1921

The impact of moves to introduce Abori- ginal land rights was felt in the Northern Territory as early as 1972 when the Federal Government froze the processing of all appli- cations for mining interests over vacant Crown land. The Aboriginal Land Rights (Northern Territory) Act was finally proclaimed on Aust- ralia Day 1977 and since that date the mining industry and the Territory legislature have struggled to make the Act work. Despite these efforts long delays have been experienced by those required to negotiate mining and explor- ation agreements under the Act. In fact explor- ation on Aboriginal land has been effectively stiffled since the introduction of the Abori- ginal Land Rights Act. The Northern Territory government and the mining industry have both sought amendment to the Act to remedy some of its more onerous problems. These efforts have generally been fruitless. Some of the recommendations put forward by Mr Justice Toohey following his recent review of the Act would provide relief in some important areas. However, any such improvements are more than offset by a number of Mr Justice Toohey's recommendations which would severely disadvantage the vast majority of Territorians. A recent survey of mining companies seeking exploration licences over Aboriginal land indicates that many of the existing diffi- culties could be overcome without significant amendment to the Act but rather by the adoption of a positive administrative approach by the Land Councils. It is now up to the Commonwealth and the Land Councils to demonstrate that their Act can work without crippling the Northern Territory economy and its mining industry.

Jan 1, 1984

By K Hines

Anglo Platinum is the worldÆs largest producer of platinum group metals, and also produces large quantities of nickel, copper and cobalt at its Refining complex in Rustenburg, South Africa. In 1995 Anglo Platinum embarked on a smelter modernisation project, primarily to reduce site emissions to below the guideline limit of 20 tonnes per day SO2, but also to increase the converting capacity in line with future projected production profiles. To achieve these requirements the existing Pierce Smith converters were replaced with a single large Ausmelt converter and a new acid plant. This was the first time that an Ausmelt furnace had been used for converting, but it had the advantages of being a very robust furnace and was fully enclosed, giving good gas capture. It was thus considered the most appropriate technology from both a process and an environmental perspective. It also enabled the smelting and converting furnaces to be decoupled. The plant was commissioned from late 2001 and the first tap was in June 2002. Despite being a new technology, ramp-up has been similar to other large scale pyrometallurgical operations. Numerous process improvements have been made since start-up, most notably a change from two-stage batch to fully continuous, resulting in the plant now operating above design in terms of throughput. Optimisation of freeboard accretion control was also a major component of the ramp-up activity. This paper discusses the commissioning and ramp-up issues of the new Ausmelt converting furnace, concentrating on the design and process changes, and summarises current operating performance against the original design objectives.

Jan 1, 2005

By Scales PJ

Fatigue is the primary cause of failure of structural and mechanical components subject to dynamic loading. Recognition of this basic fact and the development of appropriate techniques and details are important in the design and repair of off highway trucks (OHTs). The frames and appendages of OHTs and other mobile plant used in the Pilbara are subject to tough operating conditions. Any fatigue-prone details quickly show up and become a maintenance liability of considerable concern. Much of this equipment is approaching the limit of its fatigue life and maintenance managers face decisions on whether to repair or replace. Even new equipment often contains some poor details which suffer distress soon after commissioning. In those cases a repair is required which will reinstate the detail to its original intended design life. Repair details must be practical and cost effective. They must also be tailored to the capability and expertise available in the field or in local manufacturers' establishments. This is particularly important where original equipment was manufactured overseas and long delivery times are involved. Lessons are drawn from components which have failed, using the evidence constructively, to provide an upgraded part or an improved substitute. With the experience now available it is relatively easy to extrapolate to cover new problem areas. This paper describes specialised techniques of mechanical fastening and detailing for low fatigue susceptibility, built up over many years of experience with OHTs and other mining plant and equipment in the Pilbara.

Jan 1, 1982

By P B. Card

"The website www.economicevaluation.com.au, which had its origins at the Project Evaluation Conference 2009, provides a free way for industry professionals to teach themselves economic evaluation. At its core is a set of fast-moving modules and three worked examples.The website recognises that economic evaluation is a discipline with a hierarchy of three levels:decision-makingevaluating the project/businesshands-on modelling.There are a set of modules for each level that describe the concepts and activities in detail. These emphasise that the most important and rewarding work is the evaluation of Level 2. The economic model created in Level 3 is merely a working tool and should not become a sophisticated ‘trophy’ in Excel that only one or two people can comfortably use.Hands-on modelling contains three sets of practices designed to make any model rigorous and intuitive so that it can be easily understood and used by others in the project team. Even if the model develops into a long, detailed and complex workbook, it should remain easy to follow and be intuitive. The website advocates freedom to devise any architecture that best suits the project under study, but promotes rigour through the following practices:four cash streams and graphsthree architectures – concept, prefeasibility and feasibilitysix principles.The modules in the Level 2 evaluation use conversational language to describe in detail the broad range of activities needed to properly understand and characterise a project/business. It stresses that net present value is nothing more than the mathematical treatment of a whole set of opinions, is not an absolute truth and is only a fraction of the evaluation process. The modules describe in detail the range of economic metrics that should be computed and the full spectrum of equally important characterisations required to make the decision in Level 3.CITATION:Card, P B, 2016. Teach yourself economic evaluation, in Proceedings Project Evaluation 2016, pp 160–171 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By Frazer E. J, Lwin T

Measurements of coulombic efficiency (QE) for zinc electrodeposition were carried out under mass-transfer-controlled conditions using a rotating disc electrode in synthetic acidic zinc sulphate solutions. Various methods of solution preparation and purifi- cation were investigated using reagents vary- ing from analytical grade to high purity; the purest solution was obtained-by dissolving 99.9999% zinc (Koch-Light) in sulphuric acid solution (BDH Aristar). Improvements in sol- ution purity did not necessarily increase QE, especially where apparently beneficial impur- ities (e.g., Pb) were initially present. The maximum QE obtainable through variation of temperature (T), current density-(i) and elec- trode rotation rate was established using a statistical optimization technique. The QE was determined principally by T and i, with significant interaction between these factors in the highest purity solution. QE contours, which gave an overall view of solution per- formance, were constructed and predictions about the response under conditions similar to plant practice were made. Wark's Rule (the dependence of QE on zinc/acid ratio) was obeyed in the purest solution over the range of composition commonly encountered in zinc plants. High concentrations of Na2SO4 and K2SO4, which occur in some plant solutions, were found to increase QE marginally ("1.2%). The intrinsic effects of individual impurities such as Cu and Ni were evaluated by additions (up to 5 ppm) to the purest solution. Decreases in QE were found to be minimal at the impurity levels normally encountered in zinc plants.

Jan 1, 1987

For many years the mining industry at Broken Hill, New South Wales, Australia, was carried on with just sufficient attention to underground ventilation and hygiene conditions as to keep pace with necessity. However, the campaign against industrial diseases in other mining centres (notably South Africa) some years ago, brought the subject more prominently before local mining engineers.Throughout a period of several years, gradual improvement has been effected, and at the present time industrial hygiene is considered an essential part of the production operations of the various companies.In June, 1918, a move was first made by the Board of Trade advising an inquiry respecting the health of employees engaged in the metalliferous mining industry in the State of New South Wales. At the end of that year, a recommendation was made to the State Government by the Board of Trade that a Techni.cal Commission of Inquiry be appointed to examine and report upon the dust conditions of the metalliferous mines at Broken Hill. Following this a second report presented in 1919 made specific recommendations in respect to the scope of such a Commission. A Technical Commission of Inquiry was accordingly appointed and arrived in Broken Hill to inquire into the prevalence of miner's phthisis and pneumonoconiosis in the mines. Early in March, 1920, the examination of all mine employees commenced, and the work was completed in June, 1920. The full report of the activities of the Commission and the conclusions arrived at was officially published at a later date. Based on the recommendations...

Jan 1, 1940

Felspar occurs in association with quartz in the Broken Hill lode pegmatites and is brilliant green, greenish white, and white in colour. The pegmatites occur mainly in the walls in sporadic patches, parallel to the general dip of the ore deposit. The occurrences are of no economic value.Deposits of marketable felspar occur in pegmatite in a number of localities around Broken Hill, New South Wales.The majority of these are in the form of an irregular outcrop, usually of tapering length and depth. The maximum depth of any deposit yet worked in the district is about 40 ft. The felspar is occasionally contaminated by "blows" of quartz, mica and beryl, but the two latter are profitably marketable when separated.Felspars vary in colour from pink, through grey to snow white, and the colour is not indicative of the mineral content. The largest deposit at present being worked is the Egebeck quarry, about 14 miles south of Cockburn. It is a prominent outcrop, roughly circular and about 150 ft. in diameter, covered by one to three feet of overburden.The felspar is mainly massive, but contains some cleavage planes at approximately 90°. Intrusions of quartz and mica occur in patches, but the deposit appears likely to improve in size, regularity and quality below the present working floor.COMMERCIAL USES.Commercial felspars are mainly used in the ceramic industry, for which a high-grade potash felspar is required.The dental industry requires limited amounts of soda felspar with a very low Fe20s content. The poorer grades...

Jan 1, 1946

By Carlini G, Ibba R

The KSS Lead Plant (Kivcet - SNAMPROGETTI - SAMIM) of Por tovesme, owned by Nuova Samim (the sector-head Company for non ferrous metals and derivatives owned by ENI), has been operating since february 1987. This plant is based on the Soviet Kivcet licence and testwork carried out on the pilot plant of VNIITSVETMET in Ust Kameno gorsk fed by the Nuova Samim's concentrates. The plant is com pletely automatized using the most advanced technologies and it is operated by nineteen people on shift work, including all ancillary units and lead decopperizing-casting. The expected performance of the plant has been confirmed and improves day by day in relation of the operating experience, thanks to the new conceptual design of the furnace. Due to the remarkable flexi bility of the process, the integration of the lead plant with the other plants of the metallurgical complex of Portovesme rro-#4 (Electrolytic Zinc Plant, Sulphuric Acid Plant, Imperial Smel ting) has shown all the economic advantages. The lead content in the ambient air, detected by the monitors, either in the working area and on the ground outside the complex, is widely Pb W" below the stricter new limits recommanded by the E.E.C. (Economic European Community) rules and by the Italian law. The whole process is carried out in equipment completely closed and under suction and it does not require manual operations with exposure to the lead. The production cost is much lower than that performed by the traditional technology. This advantage permits wide margin to consider investment to replace the traditional technology.

Jan 1, 1989

By Grady B. V, Ault A. R, Newman O. M G, Fraser R. J, Malcolm J. McPhersqn

In all electrolytic zinc plants cadmium is removed as an impurity prior to the zinc electrowinning stage of the process. Cadmium metal is the favoured form of this by-product and most plants use an electrolytic route for its production. The formation of dendrites in cadmium electrowinning processes is the major limitation to deposition rates. There is an economic incentive, therefore, to better understand the factors affecting their growth. A technique that has been used by others to examine fundamental aspects of dendrite growth has been applied to industrial strength electrolytes. It involves potentiostatic deposition in a cell containing the electrolyte of interest. The variation in the current with time at a given overpotential allows the determination of the dendritic growth induction time. A method was developed (the Locus method) from the investigation of a set of such potentiostatic curves, obtained over a range of applied overpotentials, that appears to give a measure of electrolyte quality with respect to dendritic growth in galvanostatic deposition. The Locus technique predicts that zinc at industrial concentrations in cadmium electrolytes should have a significant effect on morphology and that deterioration of morphology will occur as the zinc concentration in the electrolyte is increased. This effect is consistent with literature prediction and was shown to relate to a reduction of the diffusion limiting current density. Magnafloc R333 is used as an additive at Pasminco Metals-EZ to control the morphology of cadmium deposits and the Locus method was successful in predicting its dendrite inhibiting properties. A possible mechanism is discussed. This work has opened avenues for future research with respect to a technique that may have an industrial application in electrolyte characterisation and has pointed to a direction in which better understanding of galvanostatic dendritic growth may be found.

Jan 1, 1993

By J Allen, B Oats, S Palaniandy, M Lollback

The Julius Kruttschnitt Mineral Research Centre has conducted an intensive VertiMill® (VTM) survey program at the Cannington mine concentrator as part of the ‘collaborative research in stirred milling technology’ program funded by Metso Minerals. Since 2003, Cannington has progressively added grinding capacity into the circuit through VTMs operating in secondary and regrinding duties. Cannington was one of the first mines to adopt this technology in secondary duty by installing two VTM-1500-WBs as part of a capacity expansion to produce sub-100 µm rougher feed. Subsequently, an additional VTM-800-WB was installed in the lead regrind circuit to prepare sub-20 µm cleaner stage feed.Several surveys were carried out to evaluate the VTM performance over a range of changed conditions. Among the key changes in operating variables were circuit power draw, feed rate and water addition to the bottom of the mill. The average specific energy for secondary duty was 3.7?kWh/t. The lead and zinc regrind mills consume 8.1 and 15.3 kWh/t respectively. Generally, the VTM installations have successfully prepared feed for rougher and cleaner circuits by reducing the top size into the floatable regime with steeper particle size distribution, which has led to enhanced recovery. The survey results show the success of VTM installations in secondary (receiving feed from autogenous circuit) and regrind duties.CITATION:Palaniandy, S, Powell, M S, Hilden, M, Allen, J, Kermanshahi, K, Oats, B and Lollback, M, 2014. VertiMill® performance updates in secondary and regrind duties at Cannington mine, BHP Billiton, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 263–272 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By R Van Laeren, G Langerak, S Fityus, K Koosmen

Co-disposal of partly-dewatered mixed-plant rejects (MPR) from coal processing into spoil dumps is gaining favour amongst Australian coalmine operators in preference to conventional tailings disposal methods which require a tailings dam. Owing to their often low permeabilities and high degrees of saturation, MPR materials may be prone to the development of excess pore pressures when covered by spoil during routine dump advancement. The likelihood of dump failure will increase if these pore pressure regimes and the associated delay of shear strength development are not accounted for during waste dump design. To date however, little is known about these pore pressure regimes due to the complexities associated with their in situ measurement.This paper describes the in situ measurement of pore pressures in a cell of MPR placed within a coalmine spoil dump. Four vibrating wire piezometers (VWPs) were placed within a cell that was then filled with MPR and allowed to consolidate under self-weight before advancing an adjacent tiphead across the cell. The VWPs recorded the transient pore pressures during MPR placement and dump construction, and their interpretations are described within the context of laboratory measured parameters. Following analysis of the measured pore pressures, their implications on shear strength and dump design are also discussed.CITATION:Koosmen, K, Langerak, G, Simmons, J, Fityus, S and Van Laeren, R, 2015. Field measurement of transient pore pressures within co-disposed processing rejects placed in a spoil dump, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 63–72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By S Zheng, Y Zhang, Z Wen, S Ma

Red mud (RM) is a solid waste product generated during alumina refinery process, and is usually stored in SFs (SFs) because it canÆt be disposed of easily. In this paper, environment degradation caused by RM-SFs was systematically assessed by the method of single factor pollution index based on the analysis data of water, soil and atmosphere sampled around one newly-built and one decommissioned RM-SFs, which are managed by an alumina production company in China. The results revealed that the ambient environment around RM-SFs is seriously polluted by alkali and mercury (Hg). The pH value of RM leachate, surrounding surface water and groundwater are all higher than the limit of water quality standards in China. And as a possible result of overflowing of high alkaline leachate, soil pH value for the decommissioned SF decreases with increasing distance between the sample collection points and the closest side of RM storage facility (RM-SF). Total Hg concentrations in RM leachate, surrounding surface water and groundwater all exceed Grade III limits of ChinaÆs Environment Quality Standards for Surface Water and Groundwater. However, the air quality was little affected as the daily average of TSP in the air is below grade II values of Chinese Ambient Air Quality Standard.CITATION :Wen, Z, Ma, S, Zheng, S and Zhang, Y, 2012. Assessment of environmental quality impacts caused by red mud storage facilities in China, in Proceedings Life-of-Mine 2012, pp 51-58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By D Laurence

Australians are at the forefront of exporting their mining expertise in a number of areas. Minerals education is just one example. The growing economies of Southeast Asia host some of the most prospective mineral fields in the world. Laos for example, hosts the world class Sepon and Phu Kham copper-gold deposits. The Philippines has the fifth largest global mineral resource inventory. These and other countries in the region lack the mining engineers, geologists and metallurgists required by international mining companies to ensure their operations are sustainable. This paper describes the author’s experience in working with mining schools in Southeast Asia and specifically the Philippines, Cambodia, Laos, Thailand and Vietnam. Various strategies to ensure sustainability and lessons learnt are presented.

Nov 22, 2011

Drainage aids are designed to assist in filter cake dewatering by reduction of surface tension. By the early 1980's severalspecialist chemical manufacturers had developed drainage aids specific to the alumina industry. Thus, after some initial laboratory work, drainage aid addition to the product hydrate filter cake was first tried at Gove in early 1981. Encouraging results led to further plant trials and a laboratory trial comparing eight different products. Fromthis last trial a product was chosen and a plant trial run in March 1982. The results achieved encouraged a further plant trial to be run during April and May, 1982 and a decision was then made to adopt the full-time use of drainage aid on the plant.Optimisation work with the drum filters and drainage aid continued until late 1983. This work not only led to optimisation of dose rates, concentrations etc., but also to significant improvements in the mode of operation of the product filtration area.

Jan 1, 1985

By X B. Sun

Mining work is a high-risk operatation under a special environment. It is affected by space, lighting, noise, vibration, dust, air pollution, etc as well as coal seam conditions, complicated geology construction, combustion of coal, gas, coal dust, etc. Factors which affects safety production are numerous, eg natural conditions, technical equipment level, producersÆ and managersÆ qualities. It is a complex system engineering to ensure mining safety and high efficiency. Among the ideology, methods and measures of safety management are the most important factors besides safety technology. Mine productive environment is a main problem that affects minerÆs work as far as safety and health are concerned. Combining ChinaÆs mine productive environment situation and using human ergonomics theory, this paper explores a series of measures and suggestions as to how to reinforce safety management, how to build up the safety management ideology, how to improve the mine production environment, how to decrease coal mine accidents, and how to ensure mining safety and high efficiency.

Jan 1, 2003

By J Lim, M Powell, P J. Scales

The current philosophy employed in the design of mineral processing plants effectively involves bolting together segmented unit operations both chosen and optimised from a product-centric perspective. In this context, integration of water saving technologies at an overall plant level becomes difficult and often only local water efficiency improvements are feasible. In general only limited benefit can be obtained from such add-on solutions. It is therefore proposed that to obtain significant savings in water consumption and reductions in the volume of discharged contaminated water in the mining process, the entire process along the mining and mineral processing chain should be addressed This paper explores aspects of the processes that may be modified to provide an integrated and combined step change saving in water consumption. It is also apparent from this study that taking a more holistic view of the process can provide significant benefits in energy savings and total cost of production, providing the potential of a substantial win-win outcome.

Jan 1, 2009

On the basis of the data known on formation, characteristics and stability of solute heavy non-ferrous metals under different temperature and pressure conditions and different concentrations of substances dissolved it is found to be possible to obtain a condition of mineral formation resulting in selective production of free-floating minerals. This process of forced mineral formation has been taken as a basis of new methods of refractory copper raw materials concentration, complex processing of lead dust from copper smelting plants, lead flotation tailings final concentration and of those of polymetallic ores concentration. This list of effective utilisation of the process is not exhaustive (Bekturganov Abishev and Shkodin, 1987; Bekturganov and Sim, 1987; Bekturganov, 1988; Abishev and Bekturganov, 1989; Bekturganov, 1989a). To understand the character of the sulphurising thermodynamic and kinetic examination have been done. Analysis of conditions of the newly formed mineral associations formation and stability facilitates the elaboration of methods of improvement of results of the valuable components selective separation.

Jan 1, 1993