Search Documents

By Roberts AW

Bulk materials handling operations depend on efficient storage and gravity flow facilit- ies. ,It is important that proper attention be given to the complete storage bin or stockpile and feeder combination. The paper briefly des- cribes the principles of efficient feeding and discusses the common types of feeders under practice. While ideally unaided gravity flow should be sought, occasions arise where flow promotion is necessary. Various types of flow promotion devices are described and their operational features evaluated.

Jan 1, 1978

Alluvial gold grades are typically highly erratic. It is very often difficult to establish with confidence the in situ grades of reserve blocks due to the small number of pit or drill hole samples available, and their erratic values. Trends in grade are often obscure. Geostatical methods are inappropriate due to the extreme nugget effect found in alluvial gold field data. Classical statistics appear more suited to such data but require assumptions to be made regarding the nature of the population sampled. Recent developments in computer intensive non-parametric statistical methods provide a new approach to dealing with some of the above problems. These methods avoid making assumptions about the type of population distribution, usually through some kind of re-sampling scheme. The bootstrap procedure involves taking the estimate of interest and synthesising its population of by re-sampling the original data a large number of times (1000+), at random and with replacement. The synthetic population is then used to draw conclusions about the likely behaviour of the true population.

Jan 1, 1985

By H Matsuno, N Oyama, T Yamamoto, K Nakajima, Y Iwami, N Saito

Recently, the quality of sinter feed ore used in sintering process has deteriorated. In particular, Fe has decreased and gangue component has increased in the sinter feed ore. Increase of gangue is not only the factor to influence sinter qualities, but also the factor to increase coke ratio in the blast furnace operation as the increase of slag ratio. Therefore, to cope with the deterioration of iron ore qualities, studies on alternative iron ore resources and development of its utilisation technology have been required.In that kind of new iron ore resources, authors focus on high-grade magnetite fine. High-grade magnetite fine decreases sinter productivity by the decrease of permeability of sintering bed. Therefore a new study for using large amount of magnetite fine is required. In the past, there are some studies about the effect of mixing ratio and size of magnetite fine on productivity and quality, but there are few studies about magnetite fine segregation in charging.In this research, the melting behaviour and interfacial reaction calcium-ferrite, which has important role as bonding agent among iron ores, melts into hematite substrate and magnetite substrate was studied. As the results, it was defined that upper segregation of high-grade magnetite fine is suitable for productivity of sintered ore. Based on this knowledge, the control method of high-grade magnetite fine segregation by magnetic force at charging was studied with DEM (discrete element method) and its verification experiments for magnetic segregation control was conducted in the laboratory.CITATION:Iwami, Y, Yamamoto, T, Oyama, N, Matsuno, H, Saito, N and Nakajima, K, 2017. Improvement of sinter productivity by control of magnetite ore segregation in sintering bed, in Proceedings Iron Ore 2017, pp 61–68 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

The management of safety has undergone a number of radical changes in the past 100 years. The most important paradigm shifts occurred through the work of Heinrich, followed by the advent of the safety systems era and, more recently, the behavioural safety approaches that have become increasingly popular around the world. Each of these æapproachesÆ to safety has left an indelible mark on the way we target safety improvements, helping decide which interventions are deployed and how they will be measured. They have also resulted in a number of æmythsÆ about safety management, each of which will be discussed, analysed and challenged in this paper. This paper highlights the complex problem of æcomplacencyÆ, that has arisen out of the increased levels of regulation and consequent perceived protection that workers enjoy in the work place. It also looks at a phenomenon called æaccident migrationÆ which results from a superficial treatment of accidents with changes to rules and procedures. The most recent approach to safety is generally known as behaviour-based safety, which flowed from the human sciences and quality management era. This approach has had a dramatic impact on the way safety is managed around the world, but still falls short in a number of key aspects, most notably the area of risk awareness and risk understanding. Many workplace accidents occur simply because the risk is unidentified, underestimated, not understood or ignored. This paper proposes a new direction for safety, called competency-based safety. It is based on cognitive psychology aimed at combating the consequence of modern protection. A case study is presented detailing the deployment of this approach throughout Placer Dome.

Jan 1, 2005

Hard rock TBMs are very often open machine layouts, with just a part roof shield over the front of the machine. The whole system is designed for fast face advance and the economy of the project often depends entirely on the rate of advance. Typically, hard rock conditions will demonstrate stable and good ground for a major part of the tunnel. However, short sections of crushed shear zones with clay and gouge material may cause serious time delays. Spiling rock bolting has been proven to be very efficient under such circumstances, provided the fully grouted rebar bolts can be placed in a controlled and practical manner.Environmental restrictions are becoming more and more a part of tunnel excavation projects. Even hard rock TBM tunnelling may require a strict ground water control, because of consequences on the ground surface from lowering the ground water level. Such consequences may be surface settlement, negative influence on ground water resources or damage to vegetation.Pressure injection ahead of the advancing tunnel face (in this paper named pre-injection), using microfine cement and chemical grouts, is today a proven technology. As examples can be mentioned (Garshol, 1997) about 100 km of pre-injected tunnels below Oslo City and about the same length of subsea tunnelling elsewhere in Norway. Examples from other parts of the world are also available, like below Stockholm, Sweden, the Inland Feeder project and Hollywood Metro both in Southern California.To take advantage of spiling rockbolts and pre-injection, it is an obvious prerequisite to be able to drill the necessary boreholes in the right positions and at the correct angle. In drill and blast excavation this is simple, but in TBM projects it has repeatedly turned out to be difficult. More than once owners have accepted bids containing reassurance from the contractor that the drilling method will be sorted out later. Experience shows that if ælaterÆ means after start of the TBM operation, it is often too late.

Jan 1, 1999

By R C. Morris

Secondary microplaty haematite in its variety of styles and generations is the defining component of the high-grade banded iron-formation (BIF)-hosted iron ores of the world that are dominated by martite (M; - haematite pseudomorphs after magnetite). The term microplaty haematite (mplH) was introduced during the CSIRO-AMIRA 1976-1994 iron ore program, and was used to differentiate the then main export martite-microplaty haematite (M-mpl H) ore types of Tom Price-Whaleback and Paraburdoo (Paleoproterozoic), from the newly exploited, more prolific supergene martite-goethite (M-G) ores (Mesozoic-Paleocene) of the Hamersley Province that are now the major Hamersley iron ore exports.Morris (1980, 1985) suggested that the most important genetic factor that distinguishes the two main ore types was regional metamorphism of Paleoproterozoic M-G ores at temperatures normally related to diagenesis (ca 80 - 100°C). As temperatures increased, mplH grew in goethite both spontaneously as well as by nucleating on martite and other pre-existing haematite. Because the conversion of goethite to haematite involves a ~27 per cent reduction in volume, the crystals probably grew within microvoids of their own creation, with iron transfer through water resulting from the process itself, a local hydrothermal process requiring no introduced hypogene fluids.Barley et al (1999) and Taylor et al (2001) concluded instead that oxidation of introduced siderite in hydrothermally metasomatised BIF ‘protore’ resulted in mplH + ankerite by reaction with heated meteoric fl uids. This postulated ‘protore’, still preserved locally at Mt Tom Price, was described during the CSIRO-AMIRA program as local post-ore BIF metasomatic residuals. These new hypogene-meteoric concepts for M-mpl H genesis have formed the basis for a range of varying local and international models that currently dominate the literature of iron ore.No valid petrographic data supporting the hypogene-supergene modelling was found but petrographic images of goethite-related mplH growth in a range of different environments are shown.

Jul 11, 2011

By M Chen, G H. Wang, J R. Zhou, P Yan, W B. Lu

Blast vibration analysis is one of the important topics in the control technology of blast vibration damage. Nowadays, blasting vibration safety standards are based on both the particle velocity and the frequency of vibration and they have been adopted widely and internationally. However, the analysis on vibration frequencies is less studied compared to investigations of peak particle velocity. For the vibration induced by a spherical charge in a viscoelasticly infinite rock mass, an expression of vibration spectrum taking into account the damping effect of rock mass is inferred. Then the attenuation laws of dominant frequencies and centroid frequencies are compared theoretically. For the case of cylindrical charge, dynamic finite element method (DFEM) software of LS-DYNA is employed to analyse the attenuation laws of characteristic frequencies. The research demonstrates that, no matter whether it is a spherical charge or a cylindrical charge, there is a local mutation or fluctuation at some distance when the blast proceeds, while the centroid frequencies conform to a smooth attenuation law. Both the multipeaks structures of vibration spectra and the decay rate difference between high- and low-frequency components contribute to the mutation or fluctuation investigated in this study. Additionally, an increase in longitudinally sonic velocity or the quality factor of rock mass produces an increase in the vibration frequencies, whereas an increase in blast source diameter or the rise time of blast load produces a decrease in vibration frequencies from a spherical charge. In borehole blasting, there is a positive correlation between the vibration frequencies and charge diameter, whereas there is a negative correlation with charge length. And altering the initiation plan will change vibration frequencies to various degrees. Finally, theoretical analysis results were validated by the empirical data from field experiments of Fengning pumped storage power station.CITATION:Zhou, J R, Lu, W B, Chen, M, Yan, P and Wang, G H, 2015. A further study on the attenuation laws of blasting vibration frequency, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 673–682 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By N Tyson

Throughout Australia and the world, there have been in recent years a number of incidents involving the reaction of ammonium nitrate based explosives with ground containing certain types of sulphides. This paper presents a comprehensive strategy designed to identify, assess and mitigate the risks involved with blasting in areas of reactive ground. Undertaking blasting in reactive or potentially reactive ground involves a degree of risk, the level of which is dependent upon the controls in place for specific sites; this in turn depends upon the degree of sound reasoning and judgement behind the implementation of these controls. Implementation of controls to minimise the risk of incidents also involves a measurable increase in production and blasting costs. To achieve a balanced solution to this matter, decision-makers need to understand how the risks eventuate, how they should be evaluated, and how control measures reduce the risk. Also required is an understanding of how the problem affects the economics of the operation, and the magnitude of this effect. It is the aim of this paper to provide a structured approach to gaining this knowledge, so that mine management, the workforce and explosive suppliers may jointly develop more effective economic and safe blasting systems for potentially reactive ground. Using a combination of fault/event tree risk assessment and semi-quantitative analysis, a structured approach to dealing with the issue will be illustrated.

Jan 1, 2001

By I Lipton

The existence of metalliferous mineral deposits on the deep-sea floor has been known since manganese nodules were discovered in the Arctic Kara Sea in 1868. Modern exploration to define commercially viable base and precious metal deposits began in the 1970s and gained further momentum in the last decade. High grade deposits have been delineated but investors remain cautious, many considering deep sea mining projects to be riskier than terrestrial projects. This paper compares opportunities and risks presented by terrestrial mining projects with those presented by deep sea mineral deposits (Table 1). The Solwara 1 volcanic-hosted massive Cu-Au-Ag sulphide deposit, the Atlantis II Deeps sedimentary base metal sulphide deposit, and the Mn-Ni-Cu-Co nodule deposits of the north-eastern Pacific Ocean are used as examples. These are advanced deep-sea projects with published Mineral Resource estimates, on the cusp of development. Off-shore diamond mines in Namibia are also considered. These examples provide a basis for comparing exploration and geological uncertainty, the technical risks of proposed mining systems, and the potential environmental and social impacts. CITATION: Lipton, I, 2018. A comparison of opportunity and risk in deep-sea and terrestrial mining projects, in Proceedings Complex Orebodies Conference 2018, pp 102–105 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By Fabjanczyk M. W

Artificial ground support has developed into a refined science over the past 20 years. From reactive support systems such as timber props and steel supports, to active systems such as roof bolts and cable anchors, ground support technology has now developed efficient systems that work well in many instances. However this paper demonstrates that there is still a long way to go to develop optimum ground support systems. Some conventional rock bolts and cable anchors emphasise their tensile capacity only, without considering other factors such as their shear strength or shear modulus, or if the support member can transfer all of its support capacity to the surrounding rock. Examples are given of the use of ground anchors with high tensile and shear capacity in underground coal mining as well as examples of slope failures in open pits where the cable bolts have remained intact because they have been unable to transfer their full capacity to the surrounding weak rock mass. For underground coal mines, speed of installation is also of primary concern, but it must also have high tensile and shear capacity both in terms of strength and stiffness. Ground support systems of the future must therefore address these problems. An innovative new rock bolt is discussed which goes some way towards solving these problems. This new rock bolt is screwed into the rock and thus has a direct mechanical interlock with the rock. Initial field results show that it has an extremely high anchor capacity and can be fully installed in approximately 30 seconds. It has considerable capacity to improve the productivity of the coal mining industry.

Jan 1, 1992

By A Llewellyn, M Varvari

The ventilation circuit at the FrogÆs Leg Mine was originally designed to permit mining to progress down to 440 m below surface at a maximum production rate of 500 kt/a, as per the feasibility study. The FrogÆs Leg resource has now been defined down to 640 m below surface at a maximum production rate of 750 kt/a. In order to allow for this increase in production depth and tonnage, it was necessary to upgrade the ventilation circuit.This paper outlines the upgrades to the ventilation circuit that were undertaken and the underlying rationale behind them.CITATION:Llewellyn, A and Varvari, M, 2013. Ventilation upgrade at the FrogÆs Leg Mine - Case study, in Proceedings The Australian Mine Ventilation Conference , pp 95-102 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

The Effect of Using Different Comminution Procedures on the Flotation of Platinum Group Minerals The use of High Pressure Grinding Rollers (HPGR) has been widely reported to have major benefits in the treatment of minerals such as iron ore and diamonds. To date there have been few investigations into its use in the treatment of ores containing Platinum Group Minerals (PGMs). HPGRs are known to reduce energy consumption and wear costs and improve the throughput in the circuit. In the present investigation the effect of the comparative use of HPGR and conventional crushing in combination with either dry or wet rod milling on the flotation of PGMs was studied using batch flotation. Previous studies of a base metal sulfide ores had shown that either HPGR or conventional crushing followed by dry milling produced the highest grades and recoveries. However in the present study it was observed that a similar treatment produced the worst results and the highest grades and recoveries were obtained for the case of conventional crushing in combination with wet milling. The HPGR showed no advantages in terms of flotation performance and dry milling produced particularly poor flotation results. The results were investigated further using various surface characterisation techniques in order to determine the reason for the decrease in grades and recoveries of platinum when using dry milling and HPGR as opposed to the case for base metal sulfides. The feed and product samples were analysed using ToF-SIMS, XPS and MLA. The paper will propose reasons to explain the different flotation behaviour of the two ore types following the various comminution processes focusing on the surface characteristics of the ores, the particle size distribution and the pulp chemistry.

Sep 13, 2010

By Aiming Z, Shenyi S, Xialei W

Zhangmatun Iron Mine is situated in the suburbs of Jinan city. Shandong, China. Because of surface environmental constraints, no suitable site can he selected to dispose of mill waste. The full mill tailings must be disposed of underground. This paper deals with the work conducted at Zhangmatun mine to develop a total tailings backfill system, taking advantage of a double- shaft blade mixer and an activating agitator to prepare backfill. Cement and ground slag are added to tailings for strength development. Two scopes have been filled and the pillars have been effectively mined out during the field trial. The application of innovative total tailings backfill technology is a new concept at the mine. Detailed planning has achieved a close integration of mining, milling and backfilling. Full mill tailings, with or without rock, are disposed of underground in a continuous process to fill, totally and systematically, the cavities formed by mining.

Jan 1, 1998

By E Yurakov, D J. Ashelford, M I. Slate

The push for increasing coal production rates continues to place increasing demands on mine management to safely and effectively control seam gas. Gas drainage strategies applied vary in both effectiveness and form. Methods employed are a function of assessed risk, gas reservoir characteristics, surface and underground access, budgetary constraints and gas utilisation potential. With the aim of establishing and optimising the effectiveness and efficiency of gas drainage systems, Australian coal miners in cooperation with gas management specialists are embracing the use of gas reservoir simulators and gas emission models. This paper discusses the evolution of gas drainage practices in Australian underground coal mines and the role of gas reservoir assessment methods in optimising gas drainage systems and gas production forecasts.

Jan 1, 2005

By D Brown, K Markovic

The world is becoming an increasingly complex environment to operate within. Adoption and evolution of technology is occurring at a rapid pace and operating spaces are growing in interconnectedness and interdependency. In mining this is evidenced by the large-scale adoption of autonomous machinery, intelligent systems, Internet of Things (IoT) devices, and robotics to realise benefits in optimisation, productivity, and safety. To enable continual delivery and growth in operational performance, and to realise the aforementioned benefits, a new approach for managing mining and metals is required (Mining Review Africa, 2023). This means that an already talent constrained workforce must learn to manage the complexity inherent, evolving, and growing in the environment (Abenov et al, 2023). A key skill that needs to be further developed and deployed to combat these challenges and to enable robust problem solving is that of systems thinking, which is already practiced in pockets within the mining industry. Experience and learning can be leveraged from other industries and their application of systems thinking to ensure that focus is maintained on areas where the benefits from which will be optimised. With targeted application, a workforce capable of effective systems thinking can be the catalyst to optimisation across mining organisations.

Sep 1, 2024

By N Weerasekara, M Powell, P Toor

The effect of liner wear on SAG mill performance has gained much attention in recent years. It is commonly observed that the three key performance criteria of SAG milling; throughput, power and product size all improve as the liner wears.The increase in throughput is generally ascribed to the increase in the grate apertures and the increase in mill volume due to the wear of these components. Whilst the decrease in product size is attributed to the reduction in lifter height and angle, resulting in more breakage by means of attrition and abrasion.Though it is widely acknowledged that the wearing of liner components such as Lifters, Plates and Grates have a significant impact on mill performance, their individual contribution to changes in mill performance has been unclear, and resultantly lead to questions like; what percentage of the throughput increase can be attributed to the increase in mill volume (plate wear)? and how much can be attributed to the increase in grate aperture (grate wear)?It has been found that through the use of grinding surveys, analysis of production data and JKSimMet it was possible to separate the effects of changing liner profile, increasing mill diameter and increasing grate aperture on the mill performance allowing for the quantification of each.The outlined methodology allows for both troubleshooting of problem liner components which reduce milling efficiency in their wear life as well as providing a basis for a more quantitative approach to liner design and reline scheduling.CITATION:Toor, P, Powell, M, Hilden, M and Weerasekara, N, 2015. Understanding the effects of liner wear on semi-autogenous grinding mill performance, in Proceedings MetPlant 2015, pp 150–161 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By M Quinteiro, Å Sundqvist

What is special about being a female mine manager? We do not believe that the challenge is greater for women in managing a mine compared to managerial positions in other male-dominated businesses. The challenge lies in the fact that it is a male-dominated business. Being a leader belonging to a minority creates a situation where competence not only lies in having technical knowledge or general leadership characteristics, but also in acquiring an understanding of the male norm and being able to behave and communicate effectively in the organisation.In order to move towards a better gender balance at senior levels it is important to set measurable objectives on desirable proportions between women and men at management levels within the company. Focus and action are required to achieve this goal. At LKAB, the current target is to reach 25 per cent women in the total workforce by 2020. To date, LKAB has reached 19.4 per cent women in the total workforce, and the number of women in management positions is 19.9 per cent.It is of vital importance to create a non-discriminating working environment to achieve equal opportunities at the workplace, to be able to use the whole workforce as a resource for recruitment of professionals and managers, thereby improving decision-making, productivity, efficiency and profitability.Women as mine managers is not a utopia, but rather an effect of long-term investments in actions that result in equal opportunities for all employees.CITATION:Quinteiro, M and Sundqvist, Å, 2016. Women as mine managers – a utopia?, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016) , pp 43–48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By L S. Shekhawat, M P. Roy, R K. Paswan, P K. Singh, A Joshi

Blasting in the mining industry is being transformed, and can no longer be treated as an art or a practice purely dependent upon experiences of individuals. Examples of key drivers that have demanded consistent and more accurate blast results are initiatives to control pit-wall damage to help mine steeper pit slope angles, to control damage to underground opening operating in close vicinity of the open pit mine. Such situation exists at Rampura Agucha open pit lead zinc mine, which is producing 5.7 Mt/a of ore and has started its underground part, which is slated to produce initially 2–2.4 Mt/a and 4.5 Mt/a in the near future. The open pit mine is currently working at 326 m depth and is designed to reach 421 m deep. It has been planned to operate the underground mine maintaining 50 m parting from the planned ultimate level of the open pit mine.Presently, open pit and underground mines are being operated simultaneously. The present average depth of underground working lies between 370 and 410 m below the surface level. Sometimes explosives up to 95 978 kg are being detonated in a blast round in open pit mine. These blasts are often apprehended as a danger to the safety and stability of underground openings. It was decided to document the impact of open pit blasting in the openings of underground workings, so that preventive measures may be taken for the safety and long-term stability of the underground mine. The impact of 86 open pit blasts has been documented in the underground openings and 258 blast vibration data has been recorded. The vibrations were recorded simultaneously in the roof, side walls and at floor levels. The highest levels of vibrations were recorded in the roof and the lowest levels at the corresponding floor levels. The pillars experienced lower level of vibrations than the roof. Blast designs were optimised at open pit mine to control vibration in view of long-term safety and stability of the underground openings. The vibrations generated due to detonation of explosives with shock tubes and electronic delay detonators have been recorded in underground openings for comparative assessment. Ground vibration recorded at roof, pillar and floor were analysed separately and threshold value of the vibration for the safety of underground workings has been determined based on the rock mass rating of the roof rock.CITATION:Singh, P K, Roy, M P, Paswan, R K, Shekhawat, L S and Joshi, A, 2015. Protection of underground mine structures due to adjoining open pit mine blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 279–288 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

THIS has been a much-neglected branch of engineering. With the majority of industries labour is the chief item of trouble and expense. Anything that will reduce trouble and increase efficiency is well worth considering. It is only of recent years that any attempt has been made on a scientific basis to improve conditions sporadic attempts having been made from time to time, privately and by law. Some have been successful, others unsuccessful not necessarily the fault of those who initiated the ideas, though naturally mistakes were made in some cases for want of experience, but those whom it was desired to benefit were not always prepared for the change, and by their distrust hampered schemes instead of assisting them.Man power is generally more expensive than machinery, though there are exceptions, such as when a small amount of work has to be done in a place where machinery does not exist, and it would not pay to instal any or where labour is cheap, and skilled workmen are scarce as in some tropical countries. When machinery is first introduced it generally causes the suspicion that it will deprive men of their work. It may cause men to vary the conditions of their work, and in some individual cases, when men are unable to conform to changed circumstances it may result in a certain amount of hardship; but, after all, the less competent must not hold back progress for the general good. Besides, changes as a rule do not take place suddenly, so old hands can generally find work at their particular calling 'till nature requires them to retire. In cases where men take to machinery, they not only find that they are relieved of the...

Jan 1, 1918

During the life of a mining project in Papua New Guinea (PNG), the greatest impact is on the people of the project area and the most intense, day-to-day contact is between these people and the project's field staff. Yet formal structures at present emphasise contact between much higher levels of national government and company personnel. Whilst understandable, this is unfortunate particularly since, given the nature of PNG politics, villagers do have a powerful influence on project success, as recent dramatic events on Bougainville have indicated. A greater role for local views and greater attention to such views by other parties is clearly required. But to achieve a successful marriage between informal village politics and the formal structures of investment procedures will require considerable patience and adjustment. This should be reflected in the cost of project development and be regarded as being as of a significance equal to that currently accorded to the technical aspects of project development.

Jan 1, 1990