Search Documents

By Ross J. F

A pillar 'is a block of coal left in the first working of a coal seam for the purpose of supporting the superincumbent strata in such a manner that the winning out roadways will be safe to traverse by men and by the coal transport system.PRINCIPLES OF PILLAR EXTRACTION.The size of a pillar is chiefly dependent on the depth of cover, and in a lesser degree on the nature of the coal, or the condition in which the seam has been laid down. In a seam at 1,100ft. depth of cover, and assuming a spec'ific gravity of 2.5 overall for the cover strata, a pressure of 1,200lb. per sq. in. is the loading on the top surface of the coal seam before mining begins.When mining commences, and as the pillars are formed, an increased load is imposed on the coal left in the pillars, according to the percentage of coal extracted in the first working. Thus, if 25% extraction is taken in the first working, the load on the pillars is theoretically increased from 1,200lb. per sq. in. to 1,600lb. per sq. in. over the area mined. If this state of things went on indefinitely it would not be possible wholly to extract a pillar because of the extreme pressure tliat would be thrown on the diminishing portion; but, fortunately, another element, that of time, enters into and assists the process of extraction.If the superimposed strata were of an entirely plastic nature, this time factor could not operate, as the cover weight would settle instantly on the remaining portion of the p'illar and finally overwhelm it. The cover strata above a pillar generally have a certain rigidity which does not allow the superimposed weight to settle instantly on the pillar fraction, and it requires a period of time to elapse before the extra weight is felt by the pillar.The time factor varies widely, and is governed entirely by local conditions; it can only be determined by experience gained on the spot or in close proximity to the area of operations. It is dependent on the strength of the strata and its characteristics under bridging conditions.It is, therefore, logical to assume that the more rapidly a pillar can be extracted the greater will be the safety factor and also the percentage of recovery of coal.Up to the present time, the operation of the extraction of pillars in this country has been, with a few exceptions, a manual one, and before mechanization of Collieries can be fully accomplished, the process will have to be performed mecharrically.

Jan 1, 1947

By N K. DavT, A Coggan

The performance of in situ, shallow water covers in controlling acid generation was evaluated at four recently decommissioned pyritic uranium tailings sites at Elliot Lake, Ontario, Canada. The tailings are acid generating, having a pyrite content of approximately five to ten per cent and a very low to non-existent alkaline buffering capacity. Adverse market conditions led to the closure of all operating uranium mines in the early- to mid-1990s, followed by rehabilitation and decommissioning of mine and waste management facilities. In order to control acidic drainage, all new and active tailings areas at Denison, Quirke, Panel, Spanish-American and Stanleigh mine sites were re-engineered to provide in situ submersion of these tailings under shallow water covers. The tailings impoundment dams were upgraded and reinforced or in some cases reconstructed, to minimise seepages and provide a minimum 1 m depth of water cover. With the exception of Stanleigh mine, which was closed in 1996 and rehabilitated during the late-1990s, the water covered Tailings Management Areas (TMAs) at other sites have been in operation for a period of six to nine years. The surface water quality at these sites is maintained at near neutral pH conditions by periodic addition of lime slurry to the established water covers. Additional treatment of effluent is provided as required to meet the discharge water quality standards. The performance of the established water covers at the sites was evaluated by analysing the annual equivalent limestone consumption data. The results were compared with the performance of an older, decommissioned Nordic TMA, which was rehabilitated using revegetation techniques. The water covers at these sites are performing as designed and acid generation has been reduced to low levels. Based on the total amount of yearly equivalent limestone required to maintain water quality in the water cover and at the effluent treatment plant, it is concluded that acid generation rate at the Denison TMA has reduced to less than 0.15 per cent of its pre-water cover conditions during normal operation and rehabilitation periods. In comparison to the revegetated Nordic TMA, the acid generation rates at Denison and Panel TMAs have decreased to less than 1.6 per cent of that at the Nordic TMA. The acid generation rate at the Quirke TMA was comparable or only slightly lower than that at the Nordic TMA because of its unique terraced cell configuration, having tailings in five hydraulically interconnected cells at different elevations. Historic acidity and oxidation reaction products, accumulated during normal operating and pre-water cover periods, are flushing from upstream locations to downstream cells, thus requiring much higher equivalent limestone additions for acid neutralisation and effluent treatment.

Jan 1, 2003

By P Meehan, R McAree, Z Guan

Equipment maintenance is 30 - 50 per cent of the operating costs for a typical mining company. While this is substantial, its importance is beyond its significance as a cost heading. Modern mining requires large amounts of investment in capital infrastructure and equipment to produce a product sold at a low unit cost. To stay competitive, such a business has to focus on full realisation of its capital investment, ie sustained production at high levels. Maintenance plays an essential role in achieving this goal. Mining companies typically use a mix of breakdown or corrective maintenance, planned maintenance, and some condition-based maintenance. The share of breakdown maintenance has been coming down through more effective planned maintenance and better condition monitoring tools. Planned or preventive maintenance (PM) is playing an increasingly important role in todayÆs mining maintenance. This is the suite of inspection and repair/replacement actions performed at scheduled time intervals as part of a preplanned activity. The activities are scheduled well in advance and, usually, the current wear-state of the machine is irrelevant. For example, the replacement of a major gear may have been planned 18 months in advance; replacement is carried out when the time comes regardless of the actual condition of the gear. The PM costs are significant and include direct cost of parts and labour as well as the opportunity cost of lost production while the machine is under maintenance. It is important to identify the optimum PM effort because over-maintenance should be avoided as much as under-maintenance. A new concept called severity-based maintenance is introduced in this paper. We have seen that measuring equipment ageing in mining merely by counting the engine hours is a very imprecise way of planning and scheduling maintenance because the damage accumulated in one hour varies enormously from operator to operator and with changing pit conditions. We recommend continuous monitoring of duty on all major equipment. This is feasible without having to fit out the machine with an army of sensors because most of the physical sensors required by dutymeters are already installed and maintained as part of the existing performance monitors. While the investment is modest, the potential benefits are huge and can be grouped under three headings:Immediate benefits will come from providing operators with direct feedback on the effect of their behaviour on machine health and training them to use this feedback to correct their operating style. The equipment can operate closer to the limits of capacity, producing more without unduly sacrificing the availability by monitoring and controlling the severity of the operation, ie the duty on the machine. Longer term benefits accrue from establishing correlations between actual time to failure data and measured equipment duty and using these correlations to optimise maintenance effort as well as planning new equipment purchases and warranty conditions.

Jan 1, 2002

By T Graham

The invention of the traditional belt and idler conveyor system is attributed to Thomas Robins in 1892. This basic concept, ubiquitous in most mining operations, has not changed markedly in 125 years and still suffers from five forms of energy losses. Firstly, Wheeler, Roberts and Jones (2004) showed that indentation rolling losses, a consequence of the indentation a roller inflicts on the belt, consume 60 per cent of all energy. Secondly, Wheeler (2006) explained that bulk solid flexure resistance resulting from material interaction and movement absorbs 20 per cent. The remaining energy is lost by idler rotating resistance (5 per cent), belt flexure resistance (5 per cent) and secondary resistances (10 per cent).Traditional conveyor systems are continuous as opposed to batch systems, implying both positive and negative features. On one hand, continuous systems have high availability (available infers ‘ready to run’), but, on the other, utilisation of availability is often low; for example, when a conveyor is running empty or below capacity. This converts into reduced system OEE (overall effective efficiency). Many attempts have been made to mitigate energy losses and low OEE issues, including development of rail-based systems. The key drawbacks have been higher capital cost, low flexibility, poor availability and lack of market acceptance.A recent conceptual development known as the ‘autonomous rail conveyor’ (ARC) promises to address issues of energy loss and poor availability and provide increased flexibility by offering solutions for difficult applications. The ARC uses a series of interconnected skeletal bogies covered with a conventional conveyor belt as a load bed running on relocatable light rail. The bogeys have two axles, each driven by integrated variable speed-geared motor and brake systems, and are connected to previous/next bogeys by specialised couplers. Power is provided by a generator (located in a dedicated bogey) and ‘daisy chain’ plug in cables. Centralised redundant control is provided at a preferred point. Although the system is batch in nature, the number of carriages and trains is flexible, meaning that the system is effectively continuous. Loading is achieved by feeding the ARC from a perpendicularly oriented apron feeder, while material off-loading is accomplished by a twist-dump operation in which the belt is twisted through an angle of 50° below the horizontal, causing material to flow from the belt into a receiving conveyor.The ARC system can run multiple trains over any distance, although benefits are more significant in distances of over two kilometres. Capital and operating costs are predicted to be lower than competitive products, with planned maintenance being simple to perform.CITATION:Graham, T, 2017. The autonomous rail conveyor significantly reduces ore haulage costs, in Proceedings Iron Ore 2017, pp 467–472 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By M J. Bourassa

In addition to the geologic risk of a particular project, the criteria that an international exploration company (æIECÆ) utilises when making an investment decision in a particular country should also include a critical analysis of the political, judicial and fiscal regime of the host country. A key investment criteria of an IEC is mineral tenure and the security and continuity of that mineral tenure under the host countryÆs existing legal system as well as the host countryÆs overall legal, political and fiscal framework, the latter of which can affect the projectÆs overall economic viability in a number of ways. The authors, Steve Vaughan and Michael Bourassa of Aird & Berlis, Toronto, Canada, have taken the position that developing an understanding of a countryÆs legal tradition is a crucial first step in analysing the mineral regulatory regime of a particular country. This paper continues their efforts to overview the most recent legal trends affecting the worldÆs mineral industry and attempts to analyse, categorise, compare and contrast differing legal systems, cultural backgrounds and economic philosophies relating to the development of mineral rights in Pacrim countries and the resulting commercial, legal, and political framework which ultimately drives the relevant mineral legislation. For the convenience of organisation of this analysis, the authors have divided the Pacrim countries into four smaller groups, firstly, on the basis of their legal tradition and, secondly, by their geographic location:Common Law Countries: USA, Canada, Australia and New Zealand; Spanish Civil Code Countries: Mexico, Central America (Panama, Nicaragua, El Salvador, Guatemala), South America (Chile, Peru, Ecuador, Colombia). Communist or Former Communist Countries: Mongolia, China, Russia. Countries of the Pacific Southwest: Phillippines, Indonesia, Malaysia, Indo-China (Vietnam, Laos, Cambodia, Thailand), Papua New Guinea. The discussion starts with an analysis of the various types of legal regimes, attempts to classify or categorise them, reiterates the necessity for the rule of law and those factors which encourage mineral exploration and development and discusses and recommends the expansion of a practical country competitiveness rating system developed by the Fraser Institute. In addition to the fundamental issue of mineral tenure û what it is and how secure it is û the paper discusses how different legal systems have shaped different approaches taken by individual nations to attract foreign mineral investment. The paper analyses the best practices and experiences accumulated in different Pacrim countries with varying legal traditions and identifies a practical country competitiveness rating system which the authors believe should be expanded to cover all minerally endowed countries. This rating system will permit countries to identify their mineral regime weaknesses and adjust their legal systems to better attract mineral investment and will also permit exploration and mining companies to compare their jurisdictional choices with those selected by their competitors.

Jan 1, 1999

Valuers of mineral properties should be aware that accountants are a major user of their opinions of value. Reliance by accountants can range from obtaining comfort that book values in balance sheets are not overstated to establishing values by which to assess the fairness of a takeover offer. Accountants using mineral property valuations clearly can't be expected to have the same level of expertise as the valuer and ""second guess"" the valuation. But they do have an obligation, under the ASC guidelines and their own professional standards, to'check the logic and reasonableness of the valuation before being able to rely on it. This means reviewing the valuation report for general sensibility, discussing the methodologies and assumptions with the valuer and being satisfied as to his competence and independence. This paper outlines how accountants use mineral property valuations, the level of scrutiny applied to such valuations and the problems commonly encountered in practice by accountants seeking to rely on them. The paper also explains how values of-mineral properties are established in company balance sheets and why these often differ, quite validly, from fair market values.

Jan 1, 1994

By G F. Johansen

The erratic and localised occurrence of economic gold grades is a common feature of high-nugget effect gold veins. The nugget effect is a consequence of small-scale geologically controlled enrichment, and the inclusion or exclusion of sparse gold particles because of the sampling process. Such deposits do not always contain visible or coarse gold, and can be characterised by fine gold particles. Economic grade accumulations are generally contained within discrete oreshoots, which are surrounded by barren to low-grade material. Problems are often encountered where small sample types (eg drill core or channel samples) often vastly understate in situ grade, due to their general inability to intersect rare gold particles. As a result, the definition of grade and its distribution is often challenging, and leads to substantial resource uncertainty. Proxies, or indicators for grade, can help the geologist gain a better understanding of grade distribution and grade potential. These are based upon geological (eg mineralogical, textural, etc) and/or geochemical (eg specific elemental ratios, fluid inclusion compositions, elemental correlations, etc) criteria. The paper discusses the use and application of such proxies through three case studies.

Jan 1, 2004

By R Ayothiraman

Tunnel excavation may induce adverse effects on nearby existing structures/foundations in urban areas. Accurate prediction of tunnelling effects on pile foundations of nearby structures in the urban environment poses a major challenge during design. Several studies have been undertaken to understand the mechanisms of the soil-tunnel-pile interaction, which focused only on influence of tunnelling on nearby existing building and foundations. However, effect of pile loading on existing tunnels did not receive enough research attention so far. So it is essential to measure the response of existing tunnel-lining due to loading on newly constructed pile to assess to the safety against the additional forces/moment caused by pile loading and to evaluate the critical distance for the proposed construction of any structures from the tunnel location. This paper presents result of three-dimensional (3D) finite element analysis carried out in ABAQUS to investigate the effects of pile loading on existing tunnels embedded in cohesive soil. It is found that the effects on tunnel lining depend on horizontal separation distance between pile and tunnel as well as location/elevation of pile tip with respect to tunnel location.

Mar 8, 2011

By E Rubio, N Morales

Currently, mine plans are optimised by using several criteria as objective functions, like profit, life-of-mine, concentration of some pollutants, mining costs, confidence level or ore resources, with consideration of constraints related to production rates, plant capacities and grades. Whilst this approach is successful in terms of producing high value production schedules, it uses a static opening sequence of the drawpoints and therefore the optimisation is made within the level of freedom left by the original opening schedule, and as a result it is far from the true optimal value of the project. This paper presents a model to optimise the sequence of drawpoint opening over a given time horizon. The emphasis is in the precedence constraints that are required to produce meaningful operational sequences considering the exploitation method (panel or block caving), physics considerations and logical rules. Further on, while it applies the standard approach of maximising net present value (NPV), it considers other targets for optimisation, like the robustness and constructability of the plans. Finally, it applies the model to real data to obtain feasible plans by means of this model. The first tests were done varying the production capacity of the mine.

Sep 26, 2011

By D R. Wines

The design of near-surface civil infrastructure requires detailed consideration of the geological/ geotechnical conditions, excavation geometry and sequence and ground support measures to ensure stability of the underground openings and minimal impact on overlying or adjacent infrastructure. Twin parallel road tunnels have been designed and built with connecting cross passages and a piggyback busway tunnel as part of a large infrastructure project in Australia. The tunnels were excavated in poor to fair quality rocks using road headers. Temporary ground support includes shotcrete, rock bolts and canopy tubes. Extensive numerical analyses have been performed to analyse the expected behaviour of the tunnels during excavation, including two-dimensional analyses using UDEC and three-dimensional analyses using FLAC3D. Structural defects in the rock are explicitly included in the 2D analyses to examine the potential for localised ground instability. The stress redistribution is captured by the 3D modelling with an accurate representation of the complex excavation geometry and the detailed excavation and support sequence. This paper presents the modelling methodology, numerical results and discussions on integrating both 2D and 3D analyses to achieve reasonable design.

Mar 8, 2011

By Tack K

During its 28-year life the MHD ISP smelter has gone through two phases, each of about a dozen years. The first phase was a learning one; in the second phase the lessons were applied and throughput and production rose strongly. Early experience revealed the robustness and the flexibility of the Imperial Smelting Process. The experience was demonstrated by strong increases in the throughput of mixed lead-zinc concentrates and of secondary (oxide) zinc materials. Purchased material quantities rose from 175 000 tonnes/year to 200 000. The required capacity increase of the IS furnace to smelt the higher throughput was achieved by relatively minor modifications; for instance a change to the internal furnace profile gained an extra two square metres in cross sectional area. The furnace hearth area has remained practically unchanged over its entire history. The paper concludes that there is still more potential to be drawn from the process and MHD intends to sustain raw material input at a new level of 240 000 tonnes/year. However, this rate will have to be achieved under the imposition of more stringent environmental and product quality standards than ever before.

Jan 1, 1993

By R C, K L. Rees, J S. J van Deventer

In contrast with previously published models for the carbon-in-pulp (CIP) process, the model proposed in this paper incorporates film transfer, intraparticle diffusion, simultaneous leaching, preg-robbing, the loading of multicomponent species, and the effects of fouling and changing cyanide levels. The rationale behind this comprehensive model is that changes in fouling and competitive adsorption along a CIP cascade affect the profiles of gold loading. As it is impossible to quantify all these non-ideal factors, a method is proposed whereby an imaginary species is postulated so as to combine all the competitive effects. A plant survey at the Telfer mine has shown that the mass loss due to a gravimetric analysis of the fouled carbon could be used directly to quantify this competitive effect. The degradation and consumption of cyanide along the Telfer CIP cascade enhance the loading of copper on to the carbon, which should be taken into account when modelling the gold profiles. It appeared that the effect of cyanide itself on the loading of gold was negligible compared with its effect on the copper. Evidently much more research is required on this topic in order to optimise CIP operations exposed to constantly changing conditions.

Jan 1, 1998

By I Jabouri

There are many physical factors that can affect the self-heating rate of coal. The presence of seam gas has often been referred to as inhibiting coal self-heating due to the limited access of oxidation sites created by the presence of the gas adsorbed on the coal pores. Similarly, the presence of bed moisture in the coal also acts as an inhibitor of oxidation by blocking access of air into the pores. Gas drainage of a coal seam prior to mining removes both gas and moisture from the seam. Bulk coal self-heating tests in a two-metre column on both gassy, as-mined and gas-drained, dried high volatile bituminous coal show that removal of gas and moisture from the coal accelerates the rate of self-heating to thermal runaway from 8.5 days to 4.25 days, from a start temperature of 30¦C, with an airflow of 0.25 L/min. The corresponding gas evolution pattern for each of these situations is different. Therefore, it is necessary to take this change in coal condition into consideration when developing a spontaneous combustion management plan.

Jan 1, 2005

By G Cooper

The Société Nationale Industriel et Minière (SNIM) is expanding its ore and concentrate production capacity in Mauritania, West Africa. This government-controlled mining company has been in production since 1963 and currently exports some 12 Mt/a.SNIM is presently doubling its magnetite concentrate production at the Guelb el Rhein mine. An existing processing line will have a second parallel production line of 4 Mt/a added. The mine is located some 600 km inland from the Atlantic coast in the heart of the Sahara Desert.The metallurgy of the ore is reasonably straightforward. It is a magnetite banded iron formation that is amenable to magnetic separation. While the existing plant uses semi-autogenous grinding and dry magnetic separation, the new processing line will use HPGRs, dry magnetic separation, and a wet milling and magnetic separation circuit for treating middlings.The process choices refl ect the scarcity of water in the region, the high cost of locally generated power and the operating experience and preferences of SNIM. Dust control in the desert environment has been a particular challenge.The metallurgical design aspects as well as the infl uence of the environmental and commercial aspects of the project are presented.

Jul 11, 2011

By S Udayakumar, S Biswal, N Sarmadi, V Sahajwalla, F Pahlevani

Recent times have witnessed a notable momentum in the interest surrounding technology dedicated to harnessing waste as valuable resources, prompted by the mounting challenges posed by waste accumulation and the swift depletion of natural resources. The carbon dissolution process within a molten iron bath stands as a pivotal reaction within the metal processing sector. The current study explores the utilisation of waste graphite electrodes (WGE) (obtained after being utilised in an electric arc furnace) as a secondary resource of carbon for dissolution into liquid iron. Experimental investigations were carried out at 1550°C using the sessile drop approach. High purity iron powder was used and the carbonaceous substrates were prepared from the ground WGE. The carbon pickup was determined using a suitable carbon analyser. Furthermore, an examination of the interfacial area between the molten iron and the WGE substrate was conducted beneath the metallic droplet, which effectively represents the iron/carbon interface. This interfacial analysis was carried out on two different samples obtained after a varying period of heat treatments at 1550°C. The interface layer was investigated using scanning electron microscopy (SEM) in conjunction with energy-dispersive X-ray spectroscopy (EDS).

Jun 19, 2024

By D Deb, R Pramanik

This paper presents a generalised methodology in smoothed particle hydrodynamics (SPH) framework to analyse dynamic failure process of rock mass having natural joint under blast-induced stress wave and expansion, and penetration of high pressure gaseous product. The necessary interactions of gas-rock are incorporated in the model which describes features of coupling between damage and plasticity in tension and compression respectively. A Drucker-Prager formulation of plasticity is used to model the behaviour of aggregate field and the Grady-Kipp damage model is employed for tensile strain. These two material behaviours are then brought together within the framework of interacting continua. The model relies on the Drucker-Prager plasticity surface to predict the dilatancy aspect of the material response and to account change of strength according to the strain rate effect. Three numerical examples are presented with rock joint and multiple blastholes.CITATION:Deb, D and Pramanik, R, 2015. Smoothed particle hydrodynamics modelling of blast-induced fracture processes in naturally jointed rock medium, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 65–70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By G van Niekerk, M Wortley

Screening is a critical part of many mineral processing circuits and keeping the aperture of the screening media within specification is vital to ensure efficient performance of the processing plant. Typical ways of estimating and/or measuring the wear of the screening media vary from very subjective methods (for instance, using the human eye) to manually checking the width of a few of the more severely worn gaps with a measurement device. Subjective methods can be flawed by human error while manual checking can distort the polyurethane or rubber materials that are used in several types of screening media. All of these errors can cause either premature replacement of panels or, even worse, poor screening of the material.Metso Process Technology and Innovation (PTI) and Metso Screening Media Solutions (SMS) have developed an innovative method that measures screen aperture using advanced image processing techniques. Field trials of the device are presented in this paper, which shows the comparison between the different methods of measuring apertures. Case studies demonstrate how the system, when combined with ScreenTrack, MetsoÆs industry leading maintenance system, and screening media, is providing users with the best possible screening solutions.

Sep 26, 2011

By K Koskinen, S Ronkainen

The flow field induced in an Outokumpu TankCell and by an OK rotor-stator mixing device in a laboratory and a process size flotation cell was modelled numerically using computational fluid dynamics (CFD). The primary target was to discover and reproduce the various interactions between the flow field and the flotation cell by numerical means. As power consumption depends sensitively on flow field, it can be regarded as a top-level derived quantity (or measure/metric) indicating the validity of the numerically obtained flow field. Having properly validated numerical means to produce the flow field the influence of various design parameters can be captured with certain accuracy. In addition, separate gas and solid phase models for bubbles and solids, respectively, were implemented. The comparisons between velocities and turbulence quantities measured using the laser doppler velocimetry (LDV) technique and CFD modelling were performed. The grid generation was performed with the commercial Gambit 1.3 and the subsequent integration and solving of the resulting algebraic equations with the commercial CFD-code Fluent 6.22. The computationally economic multiple reference frame method was included to model the moving rotor blades. Gas and solid phase models were modified mixture models.

Jan 1, 2005

By J E. Powalisz

Obtaining a representative sample of bulk materials in process industries is critical to providing valid data for process control and custody transfer (valuation). The accuracy of a sample, that is to say how well the sample represents the material in the process, is directly related to how well the process can be controlled and to how much a product may be worth. Sampling accuracy then is in fact related to bottom line profitability.Sampling theory offers information and equations on how to take a representative sample from a process, however, the actual practice of extracting a sample from the process can be more of an art.Key sampling variables include product specifications such as bulk density, particle distribution, material conveyance, practical sampler location, sampler type and sample frequency and volume/mass.This paper discusses basic sampling theory, sampling methods, types of samplers, how to develop a ‘real world’ sampling system and current manual and automated samplers.Key points include ‘practical precision and variance’, material properties, flow properties, direct sampling versus indirect sampling, sampler types and applications.CITATION:Powalisz, J E, 2014. Bulk solids sampling, in Proceedings Sampling 2014 , pp 179–188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By R Valenta, A Littleboy

Geological heterogeneity is one dimension of complexity in mining. Significant effort is put into developing an understanding of this complexity so it can be used in resource estimation, mine planning and economic modelling. However, over the decadal lifespan of a mining venture, many other dimensions add to the complexity of a mining operation. These include: technological evolution, market fluctuations; investor confidence; social norms; local expectations; and ecosystem functionality. As with geology, these factors are all heterogeneous, uncertain, time varying and represented through sparse and incomplete datasets. Recent work (Valenta et al) is beginning to show us how these risks correlate in different global settings. By analysing data relating to known, but as yet undeveloped copper deposits, this work (the complex ore body database) is demonstrating that it is the combination of issues (both price sensitive and non price-sensitive) that determine the viability of a deposit for extraction in the 21st century.CITATION: Littleboy, A, Plint, N and Valenta, R, 2018. Mining as a complex system: do we need a new model?, in Proceedings Complex Orebodies Conference 2018, pp 41–43 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018